Mga Produkto (44,000+)

EP610IDC-10 - 16-Macrocell Classic EPLD, 10ns, CDIP-24 | Altera
EP610IDC-10

EP610IDC-10 - 16-Macrocell Classic EPLD, 10ns, CDIP-24 | Altera

The Altera EP610IDC-10 is a Classic-series Erasable Programmable Logic Device (EPLD) delivering 300 usable gates, 16 macrocells, and a 10 ns pin-to-pin logic delay in a 24-pin ceramic DIP (CDIP) package. It belongs to the original Altera Classic EPLD family, fabricated on advanced CMOS technology, with a 100 MHz maximum counter frequency and 5V TTL-compatible I/O. A Classic EPLD is a non-volatile programmable logic device that combines the density of a small PLD with the speed and pin-count flexibility of early FPGAs. It sits within the broader hierarchy of programmable logic devices (PLD), between simple PAL/GAL arrays and full FPGAs. EPLDs use a sum-of-products architecture with user-programmable AND/OR planes and a fixed, deterministic interconnect, which makes them ideal for fast control logic, address decoding, and state machines where predictable timing is more important than raw gate density. Key features of the EP610IDC-10 include 16 macrocells, 4 dedicated inputs plus 20 I/O pins, an on-chip programmable interconnect, support for 100% TTL emulation, and an integrated test circuitry that allows AC specification verification during production. The device is in-system programmable via the Altera MAX+PLUS II development environment and supports JTAG-style boundary-scan testing on selected package variants. The Classic architecture is macrocell-based: each macrocell contains a programmable flip-flop, configurable I/O, and shared product-term logic that feeds the AND/OR array. Compared with one-time-programmable (OTP) PALs, the EP610IDC-10 is windowed ceramic and therefore erasable with UV light, making it suitable for development and low-volume prototyping rather than high-volume production. Typical applications include high-speed address decoding for 8086/80286-era microprocessor systems, bus interface logic, glue logic in industrial controllers, state machines for instrumentation, and 5V TTL glue-logic replacement. Designers also use Classic EPLDs to consolidate multiple discrete 74LS/74F logic packages into a single programmable device for legacy system refresh. A key design consideration is the 5V supply requirement: the EP610IDC-10 is not 5V-tolerant in a mixed-voltage system, so any 3.3V signals must be level-shifted. The CDIP-24 ceramic windowed package requires a UV eraser socket for reprogramming, so production volumes should migrate to the plastic OTP (one-time-programmable) EP610PC-10 variant. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate EPLD alternatives for legacy design maintenance and obsolescence avoidance.

RFQ Kontak
EP610IDC-15 - 16-Macrocell Classic EPLD, 15ns, 24-CerDIP | Intel
EP610IDC-15

EP610IDC-15 - 16-Macrocell Classic EPLD, 15ns, 24-CerDIP | Intel

The Intel EP610IDC-15 is a 16-macrocell Classic EPLD from the Altera Classic device family, fabricated in CMOS and housed in a 24-pin ceramic dual in-line package (CerDIP) with a 15 ns propagation delay. It provides 300 usable gates, a 66 MHz maximum operating frequency, and 5V nominal supply operation across the commercial 0C to +70C temperature range. The device implements UV-erasable / OTP logic for in-system prototyping and is supported by the MAX+PLUS II development environment. A Classic EPLD (Erasable Programmable Logic Device) is a member of the SPLD/CPLD hierarchy of programmable logic devices. Architecturally, an EPLD sits between simple PAL/GAL SPLDs and modern high-density CPLDs/FPGAs, offering non-volatile, deterministic combinatorial-and-sequential logic blocks (macrocells) with pin-to-pin timing guarantees. In the broader taxonomy: programmable logic -> SPLD/EPLD -> Classic EPLD -> macrocell array. EPLDs are valued for low-power, deterministic, single-chip glue-logic replacement of discrete 74LS/74HC TTL. Key features of the EP610IDC-15 include 16 macrocells with user-programmable I/O, 24 dedicated input pins, an internal logic-test mode for AC verification during production, pin-to-pin delay of 15 ns, and CMOS standby current well below bipolar predecessors. The CerDIP-24 ceramic package provides hermeticity for legacy industrial and military programs that demand through-hole reliability and DIP-handling compatibility. The architecture is built on a CMOS EPROM cell array driving an AND/OR macrocell fabric with programmable registers. Each macrocell includes a flip-flop with separate feedback, enabling both combinatorial and registered outputs from the same physical cell, which simplifies state-machine and counter implementation. The 5V-only supply and TTL-compatible I/O make this part a drop-in logic replacement for 24-pin TTL-based designs without I/O voltage translation. Typical applications include legacy TTL/74-series glue-logic replacement, address decoding for 8/16-bit microprocessor systems, bus arbitration and handshake logic, state-machine controllers in industrial automation, and retrofit logic boards for legacy test equipment where ceramic DIP packages are still required. Pin counts and pinout align with 24-pin standard DIP footprints, easing drop-in substitution onto through-hole motherboards. When designing with the EP610IDC-15, use a programming current of 11.0 mA typical (per Classic family datasheet), place a 0.1 uF decoupling capacitor at VCC, and budget for the 15 ns propagation delay when computing worst-case timing margins. This part is mature/EOL, so confirm last-time-buy windows with the supplier before committing to a new design. This page synthesizes distributor pricing, drop-in alternatives from the EP610 Classic family, and practical design notes that go beyond the manufacturer datasheet.

RFQ Kontak
EP610ILC-10 - Classic EPLD, 16 Macrocells, 10ns tPD, PLCC-28 | Altera
EP610ILC-10

EP610ILC-10 - Classic EPLD, 16 Macrocells, 10ns tPD, PLCC-28 | Altera

The Altera EP610ILC-10 is a 5 V, UV-erasable/OTP Classic-series Erasable Programmable Logic Device (EPLD) housed in a 28-pin plastic J-lead chip carrier (PLCC) package, providing 300 usable gates and 16 macrocells at pin-to-pin logic delays as low as 10 ns and counter frequencies up to 100 MHz. The device implements a PAL-type architecture with 16 dedicated input pins and 16 I/O macrocell outputs, giving designers a glue-logic alternative to small PAL/GAL devices with deterministic, non-volatile 5 V silicon. An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic device that combines the integration density of early PLDs with erasable EPROM-style configuration memory; in the broader taxonomy EPLD -> PLD -> programmable logic -> digital IC, the EP610 sits at the low-density end typically used to replace discrete TTL/CMOS glue logic, state machines, address decoders, and bus-interface functions. The Classic family provides pin-to-pin delays of 10-25 ns and supports counter frequencies up to 100 MHz, making it suitable for synchronous control logic in industrial and embedded systems. Key features of the EP610ILC-10 include 160 product terms, 4 dedicated inputs, 16 I/O pins, and a 5 V single-supply operation; the -10 speed grade delivers 10 ns tPD and 100 MHz fCNT, allowing the device to be clocked at full speed without metastability issues typical of slower PALs. The macrocell architecture supports both registered and combinatorial outputs with feedback, enabling efficient state-machine implementation. The PLCC-28 package uses J-leads suitable for socketed programming and field replacement, which is important for legacy and MIL-spec applications. Typical applications include address decoding in 8086/68000 microprocessor systems, glue logic in VMEbus/ISA backplanes, state machines in industrial controllers, and bus arbitration logic in legacy embedded systems. The 5 V supply and TTL-compatible I/O make the EP610 directly compatible with bipolar and CMOS 5 V logic families including 74LS, 74HC, and 74F series. When designing with the EP610ILC-10, ensure that input rise/fall times remain below the datasheet limit to avoid AC noise issues, and provide proper decoupling with 0.1 uF capacitors on each VCC pin. Because the EP610 is a legacy part with limited current production, engineers should verify lifecycle status with the distributor before committing to new designs and consider pin-compatible successors such as the EP610ILC-12 or EP910 for higher gate counts.

RFQ Kontak
EP610ILC-25 - Classic EPLD 300 Gates 16 Macrocells 25ns | Altera
EP610ILC-25

EP610ILC-25 - Classic EPLD 300 Gates 16 Macrocells 25ns | Altera

The Altera EP610ILC-25 is a 25ns Classic EPLD (Erasable Programmable Logic Device) from Altera's EP610 series, delivering 300 usable gates, 16 macrocells, and 40 MHz maximum operating frequency in a 28-pin PLCC package. It is a CMOS, PAL-type Electrically Erasable Programmable Logic Device (EEPLD) offering 160 product terms and flexible macrocell output architecture for legacy 5V logic designs. A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that combines multiple PAL-like macrocell arrays with a central interconnect, allowing engineers to implement custom glue logic, state machines, and bus interface functions without the cost of an ASIC. The EP610 belongs to Altera's Classic EPLD family — the early 5V generation that pre-dated the MAX 7000 series and now sits firmly in the legacy/last-time-buy segment of the Altera (now Intel PSG) catalog. Key features of the EP610ILC-25 include 4 dedicated inputs and 16 bidirectional I/O pins (20 total inputs), 16 macrocells with configurable D/T/JK/SR flip-flop options, 160 product terms for sum-of-products logic, and a 25ns pin-to-pin propagation delay that supports a 40 MHz internal fMAX. The device is electrically erasable, enabling in-system reprogramming during development and field upgrades. It operates from a single 5V supply (4.75V to 5.25V) with commercial temperature range of 0C to +70C. The EP610ILC-25 architecture pairs a programmable AND array feeding a fixed OR array into 16 macrocells, each capable of registered or combinatorial output with selectable feedback paths. The JTAG-less, 5V-only design philosophy makes it a straightforward drop-in for legacy PAL/GAL replacement designs and for engineers migrating older prototype boards into a single, denser, erasable part. Typical applications include legacy glue logic replacement, address decoding for 80C186/80C51 microcontroller systems, bus interface and arbitration logic, 5V state machines in industrial control, and education/lab platforms teaching programmable logic fundamentals. The 28-pin PLCC socket footprint remains widely supported on legacy backplanes and industrial SBCs. When designing with this part, verify that the development toolchain (MAX+PLUS II or older Altera classic support) is still available, as modern Quartus flows may not target the EP610 family. Confirm socket availability — J-lead PLCC-28 sockets are still in production but increasingly specialized. For new designs, evaluate MAX II or MAX V CPLDs as modern equivalents. This page synthesizes distributor stock and lead-time intelligence, pin-compatible same-family drop-in alternatives, and practical legacy-design notes not consolidated in the original Altera datasheet.

RFQ Kontak
EP610ILC10 - 16-Macrocell Classic EPLD, 10ns PLCC-28 | Intel
EP610ILC10

EP610ILC10 - 16-Macrocell Classic EPLD, 10ns PLCC-28 | Intel

The Intel EP610ILC10 is a 16-macrocell Classic EPLD (Erasable Programmable Logic Device) from Altera's EP610 family, housed in a 28-pin PLCC package with a 10ns propagation delay. It delivers pipelined data rates of up to 100 MHz and operates from a single 5V supply (4.75V to 5.25V), making it suitable for high-performance glue-logic and state-machine replacement in 5V legacy systems. A CPLD/EPLD is a non-volatile programmable logic device that retains its configuration without external memory and provides fast, deterministic propagation delays. Within the broader hierarchy, the EP610 sits as: programmable logic -> PLD -> EPLD -> Classic EPLD. It is implemented in CMOS technology, offering low static power consumption compared to bipolar PAL alternatives, and supports both UV-erasable and one-time-programmable (OTP) operation. Key features include 16 macrocells with 16 I/O lines and 4 dedicated inputs, 160 product terms, a 15ns pin-to-pin propagation delay (tPD), and a 100 MHz maximum internal clock frequency. The PAL-type AND-OR-NOT architecture with user-configurable macrocell flip-flops allows implementation of registered or combinatorial logic. The I-suffix indicates the industrial operating temperature range of -40C to +85C. The EP610ILC10 uses a classic sum-of-products architecture with a programmable AND array feeding fixed OR terms, followed by individually configurable output macrocells. Each macrocell contains a flip-flop and programmable output polarity, supporting D, T, JK, and SR flip-flop modes. The device is programmed via the Altera programming algorithm using a master programming unit, with security bit support to protect design IP. Typical applications include address decoding for microprocessor systems, bus interface glue logic, state-machine replacement, peripheral control, and 5V industrial control boards. The 100 MHz performance makes it useful in video timing and data-path control where fast, predictable logic is needed. When designing, note that the EP610 is a mature, NRND/EOL part - verify lifetime-buy status with the distributor before committing to new designs. The 28-pin PLCC package requires a through-hole or socketed footprint, so plan board layout accordingly. This page synthesizes distributor pricing, Classic EPLD family variants, and practical 5V glue-logic design notes not found in the original datasheet.

RFQ Kontak
EP610ILI-12 - 300-Gate Classic EPLD, 12ns, PLCC-28 | Altera
EP610ILI-12

EP610ILI-12 - 300-Gate Classic EPLD, 12ns, PLCC-28 | Altera

The Altera EP610ILI-12 is a 300-gate Classic EPLD from the EP610 family, packaged in a 28-pin Plastic J-Lead Chip Carrier (PLCC) and specified with a 12 ns pin-to-pin propagation delay. It provides 16 macro cells and operates from a single 5 V supply, drawing classic CMOS standby current in the I-grade industrial temperature range. Classic EPLDs (Erasable Programmable Logic Devices) are non-volatile programmable logic ICs that use EPROM/EEPROM cells to store the fuse map. They sit below modern CPLDs and FPGAs in the programmable logic hierarchy (PAL/GAL < Classic EPLD < MAX CPLD < FPGAs), and are intended for glue-logic, address decoding, state-machine and bus-arbiter functions where deterministic 12 ns timing and zero-config boot are required. Key features of the EP610ILI-12 include 300 usable gates, 16 macro cells, 4 dedicated inputs, a programmable security bit for proprietary design protection, 100% generically tested TTL-compatible I/O, and in-system 100% test coverage. The 12 ns speed grade (the "-12" suffix) places it in the mid-tier of the EP610 family, which spans from -10 to -25 speed grades. The "I" indicates the industrial temperature grade and "L" denotes low-power CMOS operation. Typical applications include TTL glue-logic replacement, address decoding for 8/16-bit microprocessors, state-machine controllers, bus arbitration, and legacy 5 V industrial control designs. Because the EP610 family is mature and now positioned as a legacy part, EP610ILI-12 is frequently specified for maintenance of existing equipment rather than new greenfield designs. When designing with this device, program it with a Classic EPLD programmer or compatible third-party tool (e.g. Altera MAX+PLUS II legacy flow). Note that Altera's PLCC package follows JEDEC MO-047 outlines and the JEDEC EEPROM cell retention spec applies for the user-programmable fuse map.

RFQ Kontak
EP610IPC-10 - Classic EPLD 16-Macrocell 10ns OTP PLD | Altera
EP610IPC-10

EP610IPC-10 - Classic EPLD 16-Macrocell 10ns OTP PLD | Altera

The Altera EP610IPC-10 is a UV-Erasable/OTP (One-Time Programmable) member of the Altera Classic EPLD family, delivering 16 macrocells and 300 usable gates in a 24-pin plastic DIP (PDIP) package. Per the manufacturer datasheet, the part provides a propagation delay of 15 ns (the -10 speed grade is the tPD-10 bin) and supports system clock operation up to 100 MHz, making it a long-standing workhorse for glue-logic, state-machine, and bus-interface integration. What is a Classic EPLD? An Erasable Programmable Logic Device (EPLD) is a CMOS-based programmable logic IC that combines PAL/GAL-style AND/OR arrays with a configurable output macrocell. EPLDs sit between simple PLDs (PALs/GALs, typically tens of gates) and complex PLDs (CPLDs/FPGAs, thousands of gates). Classic EPLDs from Altera pioneered the integration of multiple PAL-equivalent functions plus buried registers into a single 24- or 28-pin DIP, allowing engineers to replace four to six discrete 20-pin PALs with one part. The EP610 is the smallest Classic family member with 16 macrocells; its siblings EP910 (24 macrocells) and EP1810 (48 macrocells) extend the architecture for larger designs. Key features include 16 macrocells, 16 dedicated input pins (4 dedicated inputs plus 12 I/O), 20 total input pins, 160 product terms, a Turbo-only AND-OR-NOT architecture, JTAG-free ISP (programmed via an Altera Master Programming Unit or compatible third-party programmer), and 5 V CMOS/TTL-compatible I/O. Per the Classic EPLD datasheet, the device supports 100% TTL emulation and integrates cleanly with standard 74LS/74F logic families. The 24-pin PDIP form factor is friendly to through-hole prototyping and legacy system retrofits. From a technical-depth perspective, the EP610 uses a CMOS EEPROM/UV-EPROM cell technology with a programmable interconnect array feeding a sum-of-products logic matrix. Each macrocell contains a flip-flop, output enable polarity, and feedback path to the AND array, allowing D/T/JK flip-flop and combinatorial outputs to coexist in the same device. The I pin suffix denotes the industrial operating temperature range (-40C to +85C) and ceramic-windowed (UV-erasable) package, while the C suffix indicates plastic OTP. The -10 suffix indicates the 10 ns commercial tPD grade. Typical applications include bus-interface bridging (e.g., replacing multiple 74LS245/74LS373 glue-logic chips with one EP610), state-machine controllers in industrial automation, address decoding and wait-state generation in 80C186/68k/MIPS embedded systems, and legacy telecom backplane glue-logic. The 24-pin PDIP package is particularly valued in long-lifecycle industrial, military, and aerospace systems that prefer through-hole components for field-serviceability. When designing with the EP610IPC-10, plan for programming infrastructure: the part requires either a UV eraser window (I grade) or one-time-programmable configuration (C grade, no window), plus an Altera-compatible device programmer. Engineers migrating new designs should also evaluate the MAX II or MAX V CPLD families as modern, in-system-programmable alternatives with longer supply continuity. This page synthesizes current distributor availability, parametric-equivalent drop-in alternatives, and design notes not found in the original Classic EPLD datasheet, helping engineers source, second-source, and qualify the EP610IPC-10 for both new designs and legacy field-replacements.

RFQ Kontak
EP610IPC-25 - 25ns Classic EPLD, 20 I/O, 5V CMOS | Intel/Altera
EP610IPC-25

EP610IPC-25 - 25ns Classic EPLD, 20 I/O, 5V CMOS | Intel/Altera

The Intel (formerly Altera) EP610IPC-25 is a Classic EPLD (Erasable Programmable Logic Device) from the EP610 family, offering a PAL-type architecture implemented in advanced CMOS technology. It provides 25 ns pin-to-pin propagation delay, supports up to 20 inputs and 16 macrocell outputs, and contains 160 product terms for logic integration. The device operates from a single 4.75V to 5.25V supply and is rated for commercial temperature operation from 0°C to 70°C, packaged in a 24-pin plastic DIP (PDIP-24). A Classic EPLD is an early-generation programmable logic device that combines multiple PAL (Programmable Array Logic) and GAL (Generic Array Logic) functions into a single erasable, reprogrammable IC fabricated in CMOS. EPLDs sit in the hierarchy between simple PLDs (PALs/GALs) and modern FPGAs/CPUs - they offer non-volatile, in-system reprogrammable logic that integrates glue logic, state machines, address decoding, and bus interfacing on a single chip. The EP610 family was one of Altera's foundational product lines in the 1980s and remains in service for legacy industrial, military refresh, and long-lifecycle equipment designs. Key features of the EP610IPC-25 include 100% TTL emulation of standard 10K/100K ECL and 74LS logic functions, macrocell-based output architecture with configurable registered or combinatorial outputs, and on-chip erasable CMOS memory for in-system reprogrammability. The device supports multiple package options across the family and is JEDEC-standard pinout compatible within the EP610 series, enabling drop-in speed-grade and temperature-grade substitution. The architecture combines a programmable AND/OR array with dedicated output macrocells, allowing designers to replace dozens of 74LS TTL gates with a single chip. This density advantage, combined with CMOS power consumption (typically under 200 mW active), made the EP610 family a workhorse for industrial control, telecommunications glue logic, and legacy computing systems. The 'IPC-25' suffix denotes the 24-pin plastic DIP package with a 25 ns speed grade. Typical applications include address decoding and bus interfacing in 8086/68000-based embedded systems, glue logic integration in telecommunications equipment, state machine implementation in industrial controllers, and legacy TTL/74LS logic replacement. The wide supply tolerance (4.75V-5.25V) makes it tolerant of unregulated 5V rails commonly found in industrial backplanes. When designing with this device, verify that the 25 ns propagation delay meets your critical timing path requirements - the EP610 family is offered in speed grades from 15 ns to 35 ns. Note that this is an OTP (one-time programmable) windowless plastic package; for prototyping or development use the CERDIP/UV-erasable variants (EP610DC/EP610DM). This page synthesizes distributor pricing, same-family speed-grade alternatives, and practical design notes for the EP610IPC-25 that go beyond the manufacturer datasheet.

RFQ Kontak
EP610JI-30 - 16-Macrocell Classic EPLD, 30ns, CQCC28 Windowed | Altera
EP610JI-30

EP610JI-30 - 16-Macrocell Classic EPLD, 30ns, CQCC28 Windowed | Altera

The Altera EP610JI-30 is a high-performance, 16-macrocell Classic EPLD (Erasable Programmable Logic Device) from the EP610 family, housed in a 28-pin windowed ceramic JLCC (CQCC28) package and rated for a 30 ns propagation delay. It operates from a single 5 V supply using CMOS PAL-type architecture, with 4 dedicated inputs, 16 I/O lines, and 160 product terms driven by two external clocks, supporting pipelined data rates up to 100 MHz. A Classic EPLD (Erasable Programmable Logic Device) is a UV-erasable member of the programmable logic family, sitting between simple PAL/GAL devices and modern CPLDs/FPGAs in the design complexity hierarchy (PAL/GAL -> Classic EPLD -> MAX CPLD -> FPGA). The windowed ceramic package contains a quartz window that allows the device's internal EPROM configuration memory to be erased with ultraviolet light, enabling hundreds of reprogramming cycles during prototyping and design iteration. The 16-macrocell Classic architecture is sum-of-products based, with a global bus interconnecting the AND/OR arrays to a programmable output macrocell register bank. Key features of the EP610JI-30 include the 32 ns propagation delay window (often marketed as 30 ns grade per the speed suffix), 100 MHz pipeline throughput, JTAG-free boundary-scan-free classic programming via the Altera programming algorithm, and 5 V CMOS I/O. The device supports bidirectional I/O, programmable output enables, and registers on every macrocell, making it a flexible glue-logic replacement for discrete TTL/CMOS gate arrays in legacy designs. Two clock inputs feed the device's internal register clock network. The EP610 architecture uses an EPROM-based sum-of-products structure with a programmable interconnect array feeding 16 output macrocells. Each macrocell contains a programmable flip-flop, output polarity selection, and tri-state control. This architecture gives deterministic tpd that does not depend on routing congestion, a major advantage over early FPGA architectures of the same era, and the part supports synchronous and asynchronous clocking schemes with predictable pin-to-pin timing. Typical applications for the EP610JI-30 include legacy bus-interface glue logic, address decoding for M68000/i8086 systems, state-machine replacement in industrial controllers, TTL/CMOS gate-array consolidation, and prototyping of glue logic where modern FPGAs are not required. The windowed package is specifically chosen for engineering development and low-volume production where in-house UV erasure and reprogramming provide the lowest total cost. When designing with this part, note that the EP610 requires an Altera-compatible programmer (e.g., Altera Logic Programmer or third-party equivalents). Decoupling must use a 0.1 microfarad ceramic capacitor per VCC pin placed within 5 mm of the package. Inputs float when not driven; tie unused inputs to VCC or GND through a 10 kohm resistor to avoid CMOS shoot-through current. This page synthesizes distributor stock status, JLCC28 package diagrams, and pin-compatible Classic EPLD alternatives not consolidated in the original Altera datasheet, helping sourcing engineers extend the lifecycle of legacy Classic EPLD designs.

RFQ Kontak
EP610LC-15 - 16-Macrocell Classic EPLD, 15ns PLCC-28 | Altera
EP610LC-15

EP610LC-15 - 16-Macrocell Classic EPLD, 15ns PLCC-28 | Altera

The Altera EP610LC-15 is a high-performance, 16-macrocell Classic EPLD (Erasable Programmable Logic Device) housed in a 28-pin PLCC package with a 15 ns propagation delay and pipelined data rates up to 100 MHz. This CMOS-era Erasable Programmable Logic Device (EPLD) integrates 300 usable gates and 16 macrocells into a deterministic, non-volatile logic fabric, making it a foundational part for glue-logic integration in 5 V industrial systems. The device supports in-system UV-erase (windowed versions) and one-time-programmable (OTP) configurations, with -15 speed grade delivering 15 ns pin-to-pin delay. An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic device that pre-dates modern FPGAs and CPLDs. In the taxonomy, an EPLD sits between a PAL (Programmable Array Logic) and a modern CPLD/FPGA: like a PAL, it is non-volatile and instant-on, but like a modern CPLD it contains multiple macrocells with sum-of-products logic and a fixed interconnect. The Classic EPLD family from Altera was widely adopted in the 1980s and 1990s as a higher-density, faster alternative to discrete PAL/GAL devices for state machines, address decoding, and bus-interface logic. Key features of the EP610LC-15 include 16 macrocells with 16 dedicated flip-flops, propagation delays of 15 ns, fmax of 83.3 MHz counter frequency (and pipelined throughput up to 100 MHz), 24 input pins, and 16 output pins in the J-lead PLCC-28 footprint. The device operates from a single 5 V supply and is fabricated in CMOS technology, providing low static power consumption compared to bipolar PALs of the same era. Architecturally, the EP610LC-15 uses a sum-of-products (AND-OR) plane feeding configurable macrocell flip-flops, with a global interconnect that guarantees deterministic, predictable timing - critical for synchronous state-machine design. This deterministic timing, plus non-volatile configuration, makes Classic EPLDs preferred over early FPGAs in safety- and timing-critical industrial applications. The device is currently maintained by Rochester Electronics, LLC as an authorized Altera licensee for long-lifecycle programs. Typical applications include bus-interface glue logic, address decoding and chip-select generation, state-machine controllers, and replacement of discrete 74LS/74F TTL logic in 5 V systems. The wide operating voltage (single 5 V) and PLCC footprint also made it a common choice in industrial control, telecommunications backplane, and military/aerospace programs where long-term supply continuity is mandatory. When designing with this device, note that programming requires a compatible EPROM/UV eraser and programmer (e.g., Data I/O or BP Microsystems), and design entry is typically performed with classic Altera MAX+PLUS II or equivalent tools. Designers should also verify available package alternatives (windowed ceramic vs. plastic OTP) before committing to a long-lifecycle design. This page synthesizes Rochester Electronics distributor pricing, same-family Altera Classic drop-in alternatives, and practical design notes for long-lifecycle EPLD programs - information not consolidated in any single manufacturer datasheet.

RFQ Kontak
EP610LC-25 - 16-Macrocell Classic EPLD, 25ns, PLCC-28 | Intel
EP610LC-25

EP610LC-25 - 16-Macrocell Classic EPLD, 25ns, PLCC-28 | Intel

The Intel EP610LC-25 is a 16-macrocell CMOS Classic EPLD (Erasable Programmable Logic Device) with a 25 ns propagation delay, housed in a 28-pin PLCC package. It is part of Altera's original Classic EPLD family, designed for high-performance glue-logic replacement of discrete TTL and PAL/GAL devices in 5V systems. The device delivers pipelined data rates of up to 100 MHz and offers 16 macrocells organized into four Logic Array Blocks (LABs), each containing four macrocells. A Classic EPLD is a type of programmable logic device (PLD) that combines the low cost and simplicity of PAL/GAL architectures with the flexibility and density of early FPGA-like logic. In the broader taxonomy, the EP610LC-25 sits within: programmable logic device -> erasable PLD -> CMOS EPLD -> Classic EPLD family. The EP610 family was introduced in the late 1980s as one of the first UV-erasable CMOS PLDs suitable for high-speed state machine and bus-interface applications. Key features include 16 macrocells, 25 ns maximum pin-to-pin propagation delay (tPD), a 100 MHz maximum toggle frequency, and a 5V ±5% supply requirement. The device is in-system or window-erasable (UV forcerasable ceramic windowed variants) and supports industry-standard JEDEC file formats for programming. Per the Altera Classic Device Family datasheet, the EP610 provides bidirectional I/O, programmable output enable, and configurable flip-flop polarity in every macrocell. The architecture uses an AND/OR PLA-style logic array with a fixed OR plane feeding programmable flip-flop macrocells, providing predictable timing with no routing delay variance. Each macrocell contains a flip-flop, output polarity control, and a tri-state output buffer, enabling implementation of both combinatorial and registered logic with deterministic timing. Typical applications include bus-interface glue logic, state-machine controllers, address decoders, and 5V legacy system replacements. The 28-pin PLCC footprint is socket-compatible with standard 28-pin PLCC sockets, enabling easy drop-in replacement of older PAL/GAL devices. When designing with this part, designers should ensure 5V ±5% supply tolerance and provide adequate decoupling (100 nF ceramic near VCC). For new designs, modern CPLDs such as the Altera MAX II family or Lattice ispMACH 4000 series offer substantially higher logic density, lower power, and in-system programmability. This page synthesizes distributor availability, pin-compatible alternatives from the same Classic EPLD family, and practical design notes not found in the manufacturer datasheet.

RFQ Kontak
EP610LC-30 - 16-Macrocell Classic EPLD, 30ns, 5V | Altera / Intel
EP610LC-30

EP610LC-30 - 16-Macrocell Classic EPLD, 30ns, 5V | Altera / Intel

The Altera (Intel) EP610LC-30 is a 16-macrocell Classic Erasable Programmable Logic Device (EPLD) from the EP610 family, offered in a 24-pin ceramic or plastic DIP/Cerdip package with a 30 ns pin-to-pin propagation delay and 5 V CMOS supply operation. It is built on an advanced CMOS EPROM process that combines high-speed logic integration with low static power consumption and supports pipelined data rates of up to 100 MHz for high-performance glue-logic replacement. A Classic EPLD is a non-volatile programmable logic device sitting in the hierarchy of simple PLDs -> EPLD/CPLD -> programmable logic -> semiconductor. EP610 EPLDs integrate wide AND/OR arrays with a fixed macrocell architecture, providing deterministic 30 ns combinatorial delays across all 16 macrocells and offering a Turbo-only configuration mode for registered logic paths. This makes the family a direct drop-in successor to legacy 20-pin and 24-pin PAL/GAL devices in industrial and military designs. Key features include 16 macrocells, 5 V single-supply operation (VCC = 4.75 V to 5.25 V), 100 MHz pipelined throughput, in-system UV-erasable EPROM cells for design iteration, 100 % generic testability, and full JTAG-free boundary-scan test capability through the Altera programming algorithm. The device also supports 1000 erase/program cycles typical, providing field-reprogrammability for prototyping and pre-production builds. The EP610LC-30 architecture comprises a programmable AND array feeding a fixed OR array, followed by an output macrocell with a programmable flip-flop, output enable, and tri-state control. The Turbo mode bypasses the internal combinatorial delay path to deliver registered-clock rates well above the 33 MHz tpd-1 specification, while preserving the same I/O pinout across the family. Typical applications include TTL/CMOS glue-logic replacement, address decoding for 8-bit and 16-bit microprocessor buses, state-machine controllers, industrial control logic, and legacy 5 V system designs where modern FPGAs would require level shifting and reprogramming. The military / industrial temperature grade extends the operating range to -55 C to +125 C. When designing with the EP610LC-30, ensure that VCC decoupling (0.1 uF ceramic + 10 uF tantalum) is placed within 5 mm of the supply pin, and that programming voltage VPP (13 V nominal) is correctly sequenced for UV-erase windows on ceramic-windowed packages. Designers migrating from 25 ns EP610LC-25 should verify setup/hold margins since the slower part requires longer clock-to-output timing. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping sourcing engineers validate second-source decisions for legacy 5 V EPLD sockets.

RFQ Kontak
EP610LC-35 - 16-Macrocell Classic EPLD, 37ns, 5V, PLCC-35 | Altera
EP610LC-35

EP610LC-35 - 16-Macrocell Classic EPLD, 37ns, 5V, PLCC-35 | Altera

The Altera EP610LC-35 is a Classic-series Erasable Programmable Logic Device (EPLD) from the EP610 family, delivering 16 macrocells, 300 usable gates, and a 37 ns propagation delay in a 28-pin plastic J-lead chip carrier (PLCC) package. It operates from a single 5 V supply and is fabricated in CMOS technology for low power consumption. A Classic EPLD is a non-volatile programmable logic device that combines the integration of a PLD with erasable CMOS architecture, sitting in the hierarchy between discrete 22V10-style SPLDs and modern SRAM-based FPGAs. The EP610 family targets glue-logic replacement, state-machine implementation, and decoder/encoder functions in 5 V systems where a small number of logic functions must be implemented in a single package. Key features include 24 dedicated input pins, 16 output macrocells, 4 combinatorial feedback paths per macrocell, programmable I/O architecture, and a synchronous prescaler for flexible clock division. The Classic family supports 100% factory-tested AC and DC specifications with on-board logic-test circuitry that enables standard production-flow verification. Macrocells share a sum term and product term, allowing wide-input AND/OR functions to be combined with registered outputs. The EP610 uses CMOS EEPROM-based configuration cells backed by UV-erasable windowed ceramic variants (EP610I/J) and one-time-programmable plastic variants (EP610L/D). Architecture-wise, every macrocell contains a flip-flop, an output enable, and feedback into the AND-array, supporting both registered and combinatorial outputs from the same physical pin. The 37 ns tpd speed grade (-35) is the slowest of the EP610 family and trades timing margin for slightly lower dynamic current draw at lower toggle rates. Typical applications include 5 V bus decoding, address mapping for microcontroller and 8-bit/16-bit processor systems, state-machine controllers, glue-logic consolidation in industrial control boards, and replacement of legacy 22V10 PAL/GAL devices. The wide supply tolerance makes it usable in 5 V-only industrial backplanes where modern 3.3 V-only CPLDs are not pin-compatible. When designing with this part, note that the -35 speed grade is the slowest EP610 variant; verify timing margins carefully when porting -25 or -15 designs. Programming is performed via the Altera MAX+PLUS II development system and a hardware programmer; source files are still maintained in the Altera Classic Device Family support archive. This page synthesizes distributor pricing, Rochester Electronics stock status, same-family speed-grade and package alternatives, and practical design notes that go beyond the marketing blurb in the original datasheet.

RFQ Kontak
EP610LC15 - 16-Macrocell Classic EPLD, 15ns, 5V, PLCC-28 | Rochester
EP610LC15

EP610LC15 - 16-Macrocell Classic EPLD, 15ns, 5V, PLCC-28 | Rochester

The Rochester Electronics EP610LC15 is a 16-macrocell Classic EPLD (Erasable Programmable Logic Device) with a 15 ns propagation delay, supplied in a 28-pin PLCC package and fabricated on a 5V CMOS process with UV-erasable windowed ceramic package option. The Classic family provides glue-logic integration at pipelined data rates of up to 100 MHz and is fully compatible with the original Altera Classic EPLD architecture that defined the segment in the late 1980s. A CPLD/EPLD is a non-volatile programmable logic device that combines multiple PAL-style macrocell arrays on a single die, allowing designers to replace dozens of 74-series SSI/MSI glue-logic packages with a single erasable part. EPLDs sit in the broader taxonomy programmable logic device (PLD) -> EPLD/CPLD -> CMOS programmable logic -> digital semiconductor, and historically predate modern flash-based CPLDs and SRAM-based FPGAs. The Classic architecture uses a sum-of-products AND-OR array followed by an output macrocell with selectable flip-flop polarity, making it well suited for state machines, address decoding, and bus interface logic. Key features of the EP610LC15 include 16 macrocells, 10 dedicated inputs, 16 I/O pins forming a 24-pin logic array, a 15 ns pin-to-pin propagation delay (tPD), a 83.3 MHz maximum toggle frequency, and a single 5V (±10%) supply with TTL-compatible I/O. The device is in-system programmable via the Altera-standard 4-pin JTAG-style serial interface and supports security-bit protection to lock the programmed pattern. The EP610 architecture uses an EPROM-based AND array driving a fixed OR array, with each macrocell containing a programmable flip-flop, output enable, and feedback path. The 5V CMOS process yields zero standby current on disabled outputs and typical quiescent current in the low milliamp range, while the ceramic-windowed package allows pattern erasure under UV light for prototyping and design iteration. Typical applications include bus decoding for 8086/68000 microprocessor systems, address decoding for memory and peripheral mapping, state-machine implementation in industrial controllers, and TTL-to-CMOS level-interface bridging in legacy 5V designs. The 83.3 MHz fMAX also supports small pipelined datapath functions such as counter chains, frequency dividers, and shift registers. When designing with the EP610LC15, observe that the LC suffix denotes the commercial 0°C to +70°C operating range and the 15 ns speed grade; the -15 speed bin is the slowest of the EP610 family and should be selected only when timing slack allows. Programming requires a hardware programmer supporting the Classic EPLD algorithm (e.g., Altera PL-ASAP or Data I/O). Lead-finish options are matte-tin over nickel (lead-free) per modern Rochester Electronics re-creation, RoHS compliant. This page consolidates Rochester Electronics and Altera datasheet specs, cross-brand 5V-CPLD drop-in candidates, and design notes for legacy 5V glue-logic replacement that distributor listings do not present in one place.

RFQ Kontak
EP610LI-15 - 16-Macrocell CMOS EPLD, 15ns tPD | Altera (Rochester)
EP610LI-15

EP610LI-15 - 16-Macrocell CMOS EPLD, 15ns tPD | Altera (Rochester)

The Altera EP610LI-15 is a 16-macrocell ultraviolet-erasable CMOS Erasable Programmable Logic Device (EPLD) from the Classic EP610 family, supplied as a long-retail product by Rochester Electronics. It offers a pin-to-pin propagation delay (tPD) of 15 ns, a counter frequency fCNT of 83.3 MHz, and is housed in a 24-pin ceramic side-brazed DIP package (windowed, for UV erasure). The "LI" suffix denotes the commercial temperature grade (0C to +70C) and low-power CMOS process variant, while "-15" specifies the 15 ns speed grade. What is an EPLD? An EPLD (Erasable Programmable Logic Device) is a type of programmable logic that combines the non-volatility and pin-out predictability of PAL/GAL devices with the higher integration of early PLDs. In the system hierarchy, an EPLD sits between simple SPLDs (PAL/GAL) and CPLDs/FPGAs: it provides AND/OR array logic with user-programmable macrocells but offers a fixed architecture (no SRAM-based interconnect), making timing deterministic and easy to simulate. The EP610 family is the second-generation Classic EPLD line introduced after the EPROM-based EP1200 series, using a CMOS EPROM cell instead of a fuse, which made it re-programmable in-system via UV erasure. Key features of the EP610LI-15 include 16 macrcells delivering up to 48 product terms per macrocell in sum-of-products form, 100% TTL-level compatibility on inputs and outputs, and a 5 V single-supply operation. Inputs are CMOS/TTL-compatible and outputs are 3-state, allowing bus-oriented designs. The device is in-system programmable via standard EPROM programmers after UV exposure through the quartz window. Architecturally, the EP610LI-15 uses a programmable AND-OR-NOT array feeding 16 output macrocells, each containing a flip-flop and output enable. The fixed interconnect eliminates the routing-variation headaches of FPGAs and gives predictable tCO and tSU timing - useful for legacy glue-logic replacement in industrial controllers, telecom backplanes, and military refresh programs. Today the part is supported as a long-term sustainment product by Rochester Electronics, the authorized Altera/Intel legacy distributor, with 2917 units in stock per the LCSC listing as of 2026-09-10. Typical applications include address decoding in 8086/68K microprocessor systems, peripheral glue logic in VMEbus designs, state-machine controllers for industrial automation, and TTL-to-CMOS logic replacement in legacy telecom equipment. Its deterministic timing also makes it suitable for instrumentation front-ends where predictable propagation delay matters. When designing with this device, mind the 15 ns tPD budget: at 40 MHz bus rates the device is borderline, so allow one wait state if driving a fast microprocessor. The DIP-24 ceramic package requires a socket if UV erasure is planned, since desoldering a ceramic DIP repeatedly will damage pads. This page synthesizes distributor stock, lifecycle status, and drop-in same-family alternatives (EP610LI-12, EP610LC-15) not found in a single source on the manufacturer datasheet.

RFQ Kontak
EP610LI-20 - Classic 16-Macrocell EPLD, 20ns | Rochester/Altera
EP610LI-20

EP610LI-20 - Classic 16-Macrocell EPLD, 20ns | Rochester/Altera

The Rochester Electronics (originally Altera) EP610LI-20 is a Classic-series Erasable Programmable Logic Device (EPLD) featuring 16 macrocells, a 20 ns pin-to-pin propagation delay, and operation from a single 4.5 V to 5.5 V supply. Housed in a 28-pin PLCC (PQCC28) package, it is supplied today through Rochester Electronics' authorized aftermarket channel as a long-life sustaining solution for legacy Altera EP610 designs. What is a Classic EPLD? An Erasable Programmable Logic Device is a UV-erasable, electrically programmable logic IC that preceded modern CPLDs and FPGAs. Conceptually, an EPLD sits in the programmable logic hierarchy as follows: programmable logic device (PLD) -> EPLD (UV-erasable) -> CPLD (modern non-volatile equivalent) -> FPGA (largest, SRAM-based). Each Classic EPLD macrocell combines a programmable AND-OR array with a flip-flop, allowing replacement of multiple SSI/MSI glue-logic packages with a single reprogrammable device. Key features of the EP610LI-20 include 16 macrocells, 24 dedicated input pins, 20 I/O pins, a maximum toggle frequency of 100 MHz, 20 ns tPD (pin-to-pin) at worst-case commercial conditions, and CMOS technology with low standby current. The 'LI' suffix denotes the industrial temperature range (-40C to +85C) and 20 ns speed grade, while the 'L' package suffix indicates a PLCC (Plastic Leaded Chip Carrier) JEDEC outline. The EP610LI-20 implements a sum-of-products AND-OR array per macrocell with an output flip-flop and a programmable output enable. Architecturally, it offers predictable, deterministic timing suitable for replacing PAL/GAL devices with higher macrocell density. The device is programmed using a standard Altera programming algorithm via dedicated programming hardware. Typical applications include industrial control glue logic, address decoding for legacy microprocessor boards (Intel 8086/8088, Motorola 68k), bus-interface adaptation, state-machine replacement, and prototyping of discrete SSI/MSI logic functions. The PLCC-28 socket-compatible footprint also enables direct substitution onto existing Altera EP610, EP610I, and EP910 boards when pin-compatible speed grades are required. When designing with the EP610LI-20, ensure the supply rail is decoupled with 0.1 uF ceramic capacitors close to each VCC pin and that unused inputs are tied to VCC or GND to avoid oscillation. Because the part is UV-erasable, designs requiring field re-programmability must include a windowed (ceramic) package variant or migrate to a modern MAX-series CPLD for in-system programmability. This page synthesizes distributor pricing, same-brand Altera/Rochester EP610 family drop-in alternatives, and practical design notes not collated in the original datasheet, helping engineers sourcing legacy EPLDs extend the lifecycle of installed equipment without PCB rework.

RFQ Kontak
EP610LI-25 - 16-Macrocell Classic EPLD, 25ns, CMOS | Altera / Rochester Electronics
EP610LI-25

EP610LI-25 - 16-Macrocell Classic EPLD, 25ns, CMOS | Altera / Rochester Electronics

The Altera (Rochester Electronics) EP610LI-25 is a 16-macrocell Classic EPLD from the EP610 family, providing 300 usable gates with 25 ns maximum propagation delay in a CMOS, low-power 'L' speed-grade variant. This Classic-family Erasable Programmable Logic Device (EPLD) integrates AND/OR logic arrays with programmable macrocells, offering pipelined data rates up to 100 MHz and pin-compatible migration within the EP610 family. The part is supplied in a ceramic/through-hole or windowed ceramic DIP package designated 'I' for industrial temperature grade. An EPLD (Erasable Programmable Logic Device) is a type of programmable logic IC (PLD) that combines multiple PAL-like macrocells on a single CMOS die, erasable via ultraviolet light through a quartz window on windowed packages. Classic EPLDs occupy the architectural middle ground between simple PALs/GALs and modern high-density FPGAs or CPLDs: they offer deterministic combinatorial and registered logic, predictable pin-to-pin timing, and simple development flows based on Altera's legacy MAX+PLUS II / Classic compiler toolchain. In a system hierarchy, EPLDs sit under CPLDs and FPGAs but above discrete 74-series glue logic for designs needing a few hundred gates of custom decode, state-machine, or bus-interface logic. Key features include 16 macrocells, 300 usable gates, 25 ns tPD, 100 MHz pipelined fMAX, 4 dedicated inputs plus 16 I/O pins, and programmable output macrocell polarity. The device offers three-state output control on every I/O pin, a synchronous preset/reset structure shared across the macrocell array, and low CMOS standby current typical of the 'L' power variant. JTAG/boundary-scan test is not present on this Classic part - test access is via the standard functional pins and the dedicated programming algorithm. From an architectural standpoint, the EP610 is a sum-of-products AND-OR array feeding a global interconnect that drives 16 output macrocells. Each macrocell contains a flip-flop, output polarity bit, and three-state buffer that can be individually enabled. This structure delivers predictable, deterministic timing that does not require place-and-route iteration, making EP610 designs reproducible across production lots. Typical applications include legacy glue-logic replacement on industrial and military backplanes, address decoding for 8- and 16-bit microprocessor systems (8086, 68000, Z80), bus arbitration and interrupt controllers, state-machine controllers, and small peripheral interfaces where modern CPLD/FPGA density is unnecessary. The 'I' temperature grade and ceramic package also make it suitable for extended-temperature and Mil-spec system designs still in active production. When designing with EP610LI-25, use Altera MAX+PLUS II or the Classic compiler with a supported programmer, and respect the 25 ns tPD budget when cascading logic across multiple macrocells. For new designs, prefer the EP610LI-20 or EP610LI-15 speed grades if timing margin is tight; the EP610 family shares pinout across all speed grades, simplifying speed up/down swap on existing boards. This page synthesizes distributor pricing from Rochester Electronics and authorized partners, lists same-family drop-in pin-compatible alternatives from the EP610 family, and surfaces practical programming and design notes not consolidated in the original Altera datasheet.

RFQ Kontak
EP610LI-30 - 16-Macrocell Classic EPLD, 30ns | Rochester
EP610LI-30

EP610LI-30 - 16-Macrocell Classic EPLD, 30ns | Rochester

The Rochester Electronics EP610LI-30 is a high-performance, 16-macrocell Classic Erasable Programmable Logic Device (EPLD) offering pipelined data rates of up to 100 MHz and a 30 ns pin-to-pin propagation delay, supplied in a 24-pin ceramic DIP package. Originally designed by Altera and now manufactured and supported by Rochester Electronics, this member of the Classic EPLD family integrates multiple 24V18 macrocell PAL-like AND/OR arrays into a single CMOS device, replacing 4 to 8 discrete SSI/MSI TTL or CMOS logic packages with one programmable part. An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic IC that combines the architectural density of a PLD with the erasability of an EPROM. Within the broader semiconductor taxonomy, EPLDs sit between simple SPLDs/CPLDs and large FPGAs: they offer deterministic timing, low static power consumption, and zero in-system configuration time because the logic is realized in silicon at manufacture-time via fuse/anti-fuse links rather than SRAM lookup tables. The Classic EPLD family historically targeted glue-logic replacement, address decoding, state-machine encoding, and bus-interface adaptation in industrial, telecommunications, and legacy computing designs. Key features include 16 sum-of-products macrocells with user-configurable output polarity, a 5 V CMOS core with TTL-compatible I/O, an internal 24V16 AND array, and a built-in test mode for verification. The device is fabricated in UV-erasable CMOS technology and is windowed ceramic DIP-packaged for military and aerospace programs that require proven, long-life-cycle silicon. The EP610LI-30 uses a MAX-type macrocell architecture with a configurable D/T/J-K flip-flop per cell, a global clear and a product-term clock network, and a synchronous preset that simplifies state-machine design. The pipelined register path allows internal fMAX up to 100 MHz, while combinational paths at 30 ns make the part well-suited to legacy system-clock domains of 25-33 MHz. Typical applications include legacy peripheral adapter cards, industrial motor-control glue logic, MIL-STD-1553 bus interface decoding, telecom backplane address decoding, and avionics retrofit programs. The device is especially useful when modern FPGAs are overkill or where a non-volatile, instantly-on logic element is required. When designing with this part, note that the 'LI' suffix denotes a windowed ceramic DIP for MIL/Aero temperature ranges (-55C to +125C), so erase/programming requires a UV eraser and a Classic-series programmer (e.g., Altera PLDS-JAM). Designers migrating to surface-mount should consider the equivalent PLCC-package variant. This page synthesizes Rochester stock data, same-family drop-in alternatives, and Classic EPLD design notes not found in the legacy Altera datasheet, helping engineers source obsolete EPLD silicon for long-life programs.

RFQ Kontak
EP610LI-35 - 16-Macrocell Classic EPLD, 35ns, PLCC-28 | Altera
EP610LI-35

EP610LI-35 - 16-Macrocell Classic EPLD, 35ns, PLCC-28 | Altera

The Altera EP610LI-35 is a high-performance 16-macrocell Classic EPLD (Erasable Programmable Logic Device) from the EP610 family, delivering pipelined data rates of up to 100 MHz in a 28-pin PLCC package. Operating from a single 5 V supply, the device integrates 300 usable gates and 16 macrocells interconnected via a programmable AND-OR array, with 20 total inputs and 16 I/O lines. The 'LI' suffix denotes a windowed ceramic package suitable for military temperature range operation, while the '35' speed grade specifies a 35 ns propagation delay. A Classic EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic device that uses EPROM, EEPROM, or Flash cells to store the configuration. CPLDs/EPLDs belong to the broader hierarchy of programmable logic devices (PLDs), which sit between discrete logic ICs and full FPGAs in density and complexity. The Classic family implements a PAL-style AND-OR architecture with macrocells containing flip-flops, making it ideal for glue logic, state machines, and bus interfacing in 5 V systems. Key features of the EP610LI-35 include PAL-type architecture with 16 macrocells, 160 product terms for wide sum-of-products logic, 4 dedicated inputs plus 2 external clock inputs, and CMOS technology for low power consumption. The device provides in-system programmable logic with high noise immunity typical of CMOS designs, supporting synchronous designs through dedicated clock networks and asynchronous designs through programmable flip-flops. The EP610 architecture uses a programmable interconnect scheme with each macrocell containing a configurable flip-flop with preset/reset capability. Logic is implemented as sum-of-products terms that feed the 16 macrocell flip-flops, which can be configured as D, T, JK, or SR types. This architecture is well suited to decoder, encoder, and state-machine implementations where deterministic timing is critical. Typical applications include bus interface glue logic, address decoding, state machines, and peripheral control in legacy 5 V systems. The wide 5 V tolerance makes it suitable for industrial control and replacement of discrete TTL/CMOS logic, particularly in long-lifecycle equipment where modern FPGAs are unsuitable. The windowed ceramic package enables reprogrammability for prototype development and field updates. When designing with the EP610LI-35, ensure that all unused I/O pins are properly terminated to avoid floating-input issues in CMOS designs. The 35 ns propagation delay must be analyzed against the target system's timing budget, with attention to the worst-case delay paths through multiple logic levels.

RFQ Kontak
EP610PC-15 - 16-Macrocell Classic EPLD, 15ns PDIP-24 | Altera
EP610PC-15

EP610PC-15 - 16-Macrocell Classic EPLD, 15ns PDIP-24 | Altera

The Altera (now Intel) EP610PC-15 is a Classic EPLD (Erasable Programmable Logic Device) from the original Altera Classic family, delivering 300 usable gates, 16 macrocells, and a 15ns pin-to-pin logic delay in a 24-pin plastic DIP (PDIP) through-hole package. It operates from a single 5V supply and supports pipelined data rates of up to 100 MHz, making it the slowest-speed grade in the EP610 Classic EPLD lineup but still suitable for many glue-logic and bus-interface tasks. An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic IC that combines the architectural simplicity of PAL/GAL devices with higher gate density and on-chip macrocell registers. Within the broader taxonomy, the EP610 belongs to the chain: EPLD -> CPLD -> Programmable Logic Device (PLD) -> Logic IC -> Integrated Circuit. Classic EPLDs are CMOS UV-erasable parts historically used to replace multiple discrete PAL/GAL chips with a single, in-system reconfigurable device, sitting upstream of the FPGA family in the programmable-logic evolution. Key features of the EP610PC-15 include 100% TTL emulation, on-board logic test circuitry for AC/DC verification during production flow, integrated macrocell flip-flops, and a choice of speed grades (-15, -20, -25, -30, -35) with the -15 being the slowest variant. The Classic family supports 300 to 900 usable gates, but the EP610 specifically targets the 16-macrocell / 300-gate entry point for low-density glue logic. It is a PAL-type architecture with CMOS technology and a 17 ns tPD (per Datasheets360 listing). The device architecture is based on a sum-of-products PLA-style AND/OR array feeding 16 macrocells, each with a programmable flip-flop and I/O control. This makes the EP610PC-15 well-suited to state-machine, address-decoding, and bus-arbitration functions where non-volatility, deterministic timing, and a simple development toolchain (MAX+PLUS II) are valued. Typical applications include address decoding in 8086/68k/MIPS-based systems, glue logic between microprocessors and peripherals, bus arbitration, state-machine controllers, and legacy industrial control replacement where original Altera Classic parts must be form-fit-function substitutes. Because the EP610 is in production through Rochester Electronics as a long-life sustaining product, it continues to be specified for EOL (end-of-life) boards and long-lifecycle aerospace/defense programs. When designing with this device, note that the 15ns grade has the slowest tPD in the family - if your timing budget is tight, choose -20, -25, -30, or -35 instead. Verify the supply voltage (5V only) and the package footprint (24-pin PDIP, 0.3 inch row spacing) match the legacy PCB layout before substitution. This page synthesizes Rochester Electronics distributor pricing, same-family drop-in alternatives, and design notes not found in the original Altera datasheet, providing practical sourcing intelligence for engineers maintaining legacy EPLD designs.

RFQ Kontak
EP610PC-20 - Classic EPLD, 16 Macrocells, 100 MHz | Altera
EP610PC-20

EP610PC-20 - Classic EPLD, 16 Macrocells, 100 MHz | Altera

The Altera (Rochester Electronics) EP610PC-20 is a Classic-family Erasable Programmable Logic Device (EPLD) with 16 macrocells, 300 usable gates, and pipelined data rates of up to 100 MHz, housed in a 24-pin PDIP package. The -20 speed grade denotes a 20 ns pin-to-pin propagation delay (tPD), suitable for high-performance glue-logic and state-machine replacement in legacy 5 V systems. According to Rochester Electronics' datasheet excerpt, the device is fabricated in CMOS EPROM technology, supports in-system UV erasure via a windowed package option, and is pin-compatible with the broader EP610 family. A Classic EPLD is a type of programmable logic device that combines the non-volatility and instant-on behavior of EPROM with the flexibility of combinatorial and sequential logic implementation. In the system hierarchy, an EPLD sits between simple PLDs (PAL/GAL) and modern CPLDs/FPGAs, providing predictable timing, deterministic propagation delay, and a small macrocell count optimized for fast logic integration. The EP610 was Altera's second-generation Classic EPLD, designed for high-speed decoder, counter, and bus-interface applications where bipolar PALs lacked speed or density. Key features of the EP610PC-20 include 16 macrocells, 24 dedicated input pins, 16 flip-flops with individual clear/preset control, programmable output polarity, and a 5 V ±10% single-supply operation. The device offers 100 MHz registered operation, 20 ns tPD (commercial grade), and a maximum I/O count consistent with the 24-pin PDIP footprint. The architecture is a sum-of-products array feeding 16 macrocells, with each macrocell containing a programmable flip-flop and output enable logic, allowing implementation of either combinatorial or registered logic functions. Architecturally, the EP610 uses a unified AND/OR array with a fixed internal interconnect, eliminating the routing variability of FPGAs. The CMOS EPROM process provides zero standby power and full TTL compatibility, while the deterministic tPD enables accurate timing analysis without static timing closure tools. Compared to bipolar 20 ns PALs, the EP610PC-20 adds programmability of registered outputs and eliminates the need for separate PAL/flip-flop pairs on a board. Typical applications include bus decoders and address-mapping logic in 8086/68000-era microprocessor systems, high-speed glue logic between ASICs and standard peripherals, replacement of multiple 20 ns PALs with a single device, DMA state machines, interrupt controllers, and legacy industrial control designs. The 100 MHz pipelined throughput also makes the device useful for frequency-division and clock-distribution networks. When designing with the EP610PC-20, ensure that the 5 V supply is within ±10% tolerance, place a 0.1 µF decoupling capacitor near each VCC pin, and confirm that the device programmer supports the Classic EPLD algorithm (e.g., Data I/O, BP-1200, or equivalent). For production, use the one-time-programmable (OTP) windowless variant if UV erasure is not required, and program the security bit to prevent pattern readback. This page synthesizes distributor pricing from Rochester Electronics and authorized resellers, same-family drop-in alternatives (EP610PC-15, EP610LC-25, EP610DC-25) from the Site MPN list, and practical design notes not found in the original manufacturer datasheet.

RFQ Kontak
EP610PC-20T - 16-Macrocell Classic EPLD, 20ns, PDIP-24 | Intel
EP610PC-20T

EP610PC-20T - 16-Macrocell Classic EPLD, 20ns, PDIP-24 | Intel

The Intel (formerly Altera) EP610PC-20T is a 16-macrocell Classic EPLD (Erasable Programmable Logic Device) with 300 usable gates, a 20 ns pin-to-pin propagation delay, and a 62.5 MHz pipelined data rate, housed in a 24-pin plastic DIP (PDIP) through-hole package. It is a UV-erasable, CMOS Classic-series EPLD designed for glue-logic and state-machine replacement in legacy 5V systems. A CPLD/EPLD is a non-volatile programmable logic device that retains its configuration when power is removed, sitting in the broader hierarchy of programmable logic devices (PLD) -> CPLD -> EPLD -> programmable logic IC. Classic EPLDs predate modern flash-based CPLDs and are widely used for board-level integration of random logic, address decoding, bus arbitration, and peripheral control in industrial, telecom, and military systems where 5 V tolerance and proven long-term reliability are required. Key features of the EP610PC-20T include 16 macrocells, 16 dedicated inputs plus pin feedback, 4 product-term OR arrays, a 5 V VCC supply, a 20 ns tPD commercial-grade speed grade, and on-board logic test circuitry that allows verification of function and AC specifications during standard production flow. The 'PC' suffix denotes the PDIP package, '20' denotes the 20 ns speed grade, and the 'T' indicates tape-and-reel packaging. The device is programmed using the MAX+PLUS II development system and supports the Classic-series JTAG-compatible programming interface. The EP610PC-20T is built on a CMOS EEPROM/EPROM-based architecture with on-chip charge pumps for in-system programming, programmable interconnect, and product-term logic arrays per macrocell. Each macrocell contains a programmable register, feedback path, and output enable control. Designers can synthesize combinational or registered logic up to 300 gates equivalent, replacing dozens of discrete 74-series TTL/CMOS parts. Typical applications include 5 V address decoding, glue logic for ISA/VME bus systems, state-machine replacement in industrial controllers, microcontroller I/O and peripheral expansion, and legacy telecom line-card interface logic. The through-hole PDIP-24 package is well suited to through-hole PCB assembly, prototype boards, and MIL-spec or ruggedized designs. When designing with the EP610PC-20T, remember that Classic EPLDs use the legacy MAX+PLUS II toolchain; modern Quartus support is limited. Decoupling 0.1 uF ceramic caps must be placed on every VCC/GND pair, unused inputs must be tied to VCC through a 10 kohm resistor, and the device must be erased under UV light before reprogramming. This page synthesizes distributor pricing, drop-in same-brand speed-grade alternatives, pinout diagrams, and practical design notes that are not aggregated on the manufacturer datasheet or single distributor listings, giving engineers a single decision-grade reference.

RFQ Kontak
EP610PC-25 - 16-Macrocell Classic EPLD, 25ns PDIP-24 | Altera
EP610PC-25

EP610PC-25 - 16-Macrocell Classic EPLD, 25ns PDIP-24 | Altera

The Altera (Intel) EP610PC-25 is a Classic EPLD (Erasable Programmable Logic Device) from the EP610 family, delivering 16 macrocells, 300 usable gates, and 25 ns pin-to-pin propagation delay in a 24-pin PDIP (0.3 inch) through-hole package. It is a CMOS PAL-type OTP (one-time programmable) PLD with pipelined data rates up to 100 MHz and operates from a single 5 V supply. What is a Classic EPLD? An EPLD (Erasable Programmable Logic Device) is a type of Programmable Logic Device (PLD) that combines the non-volatility and simple programming model of a PAL (Programmable Array Logic) with the higher macrocell density of early complex PLDs. Classic EPLDs sit in the hierarchy between simple PAL/GAL devices and modern CPLDs/FPGAs, providing AND/OR plane logic with user-configurable macrocell flip-flops. EP610-class devices were commonly used to replace discrete 74LS glue logic and SSI/MSI PALs in 5 V industrial and computer-peripheral designs. Key features include 16 macrocells (organized as four 16x8 PAL-like blocks of four macrocells each, with a sum term shared across each block), 24 dedicated input pins, 10 I/O pins, 33 product terms per macrocell, asynchronous clocking per macrocell, and architectural support for D, T, JK, and SR flip-flops. The EP610 is electrically erasable, allowing in-system reprogramming via the Altera programming algorithm. The EP610PC-25 is built on a 5 V CMOS process with UV-erasable EPROM cells (the PC suffix denotes PDIP package). It supports synchronous or asynchronous register loading, programmable output enable per macrocell, and output macrocell polarity control. With 25 ns propagation delay and a 100 MHz internal pipelined data rate, it is positioned for glue-logic and interface-controller applications rather than high-density state machines. Typical applications include 5 V glue-logic replacement in microprocessor systems, address decoding for 80-series CPUs, peripheral-interface controllers (bus arbitration, interrupt controllers, custom state machines), and legacy industrial-control retrofits. The PDIP-24 footprint is socket-friendly for prototype and through-hole assembly. When designing with the EP610PC-25, allocate enough macrocell feedback for buried combinatorial logic; the AND-OR array is shared across each 16x8 block, so heavily skewed product-term distribution can limit fitting. Programming requires an Altera-compatible programmer (e.g., Altera Logic Programmer) and the MAX+PLUS II or AHDL+ toolchain. This page synthesizes distributor pricing, legacy EPLD family equivalents, and application guidance not consolidated in the original Altera datasheet.

RFQ Kontak
EP610PC-25T - 16-Macrocell Classic EPLD, 25ns, PDIP-24 | Intel / Altera
EP610PC-25T

EP610PC-25T - 16-Macrocell Classic EPLD, 25ns, PDIP-24 | Intel / Altera

The Intel / Altera EP610PC-25T is a 16-macrocell Classic EPLD (Erasable Programmable Logic Device) in the Altera Classic EP610 family, packaged in a 24-pin plastic DIP (PDIP-24) and specified for a 25 ns pin-to-pin propagation delay. It delivers 300 usable gates, 16 dedicated registers, 16 user I/Os, and pipelined data rates up to 100 MHz from a single 5 V supply, making it a compact, non-volatile logic integration point for glue-logic, bus decoding, and state-machine designs. A Classic EPLD is a one-time- or UV-programmable CMOS PLD positioned below the CPLD and FPGA tiers in the programmable-logic hierarchy. It sits architecturally between a PAL/GAL and a modern CPLD: more flexible than a fixed-AND/OR PAL, but simpler and lower-cost than a JTAG-configurable CPLD or SRAM-based FPGA. In a typical digital system the EP610 replaces multiple SSI/MSI 74LS/74HC glue-logic packages - address decoding, wait-state generation, interrupt steering - so designers reduce board area, BOM count, and assembly cost without writing HDL or purchasing a toolchain beyond a simple programmer. Key features of the EP610PC-25T include: 25 ns tPD (pin-to-pin delay, commercial speed grade), 16 macrocells each with a configurable flip-flop, product-term allocation for both combinatorial and registered logic, 5 V ±5% VCC operation, and an industry-standard JEDEC DIP-24 footprint compatible with UV-windowed EP610DC-25 ceramic parts on the same PCB. The T suffix denotes a tube-packaged shipping form, while the EP610PC-25 is shipped in tray; both share identical die and pinout. Architecturally the EP610 uses Altera's Classic macrocell with sum-of-products logic feeding a programmable output cell that can be configured as registered, combinatorial, or bi-directional I/O. The device is programmed via an industry-standard 4-pin JTAG-style interface in production programming. Its CMOS EPROM-style non-volatile configuration means no boot PROM is required, simplifying board design. Designers should be aware that the device is NOT in-system programmable and must be erased by UV light if a windowed CERDIP variant is used, or discarded if a plastic one-time-programmable (OTP) variant like the EP610PC-25T is used. Typical applications include industrial control boards, telecom line cards, legacy peripheral adapters, address decoding for microprocessors, and replacement of 74LS-series glue logic. The EP610PC-25T is also widely used for long-life-cycle embedded systems where supply continuity for over a decade is required. When designing with the EP610PC-25T, plan for a 5 V supply rail, place a 0.1 µF decoupling capacitor adjacent to each VCC pin, and budget for the OTP programming step (the device cannot be reprogrammed in-circuit). Engineers migrating from EP610PC-25 should note identical pinout, identical die, and identical speed grade. This page synthesizes distributor pricing, drop-in alternatives drawn from the Altera Classic device family, and practical design notes not found in the manufacturer datasheet alone.

RFQ Kontak