Mga Produkto (44,000+)

ICS621MIT - 1:4 200MHz Clock Buffer | Renesas Electronics
ICS621MIT

ICS621MIT - 1:4 200MHz Clock Buffer | Renesas Electronics

Renesas Electronics ICS621MIT is a low-skew 1-to-4 clock buffer operating up to 200 MHz in an 8-SOIC package. It accepts one clock input and provides four buffered clock outputs, allowing a single low-frequency source to drive multiple timing-critical loads while reducing fanout loading. The 8-SOIC package is a surface-mount option for compact digital, communications, networking, and test equipment designs. A clock buffer is a digital timing IC that reproduces a clock signal through one or more output stages. Clock buffers and clock drivers belong to the broader clock and timing IC category, where their practical role is to isolate a source from capacitive loading, extend signal reach, and distribute a common timing reference. In a multi-load system, a buffer helps each receiver see a cleaner transition sequence than it would when connected directly to a long or heavily loaded clock trace. The principal characteristics of ICS621MIT are its 1:4 fanout ratio, 200 MHz maximum clock frequency, low-skew architecture, and 8-SOIC package. A 1:4 ratio means that one incoming clock can feed four output branches, reducing the number of separate distribution stages required in a moderate-complexity system. The 200 MHz operating capability makes the device relevant to designs carrying clock signals in the hundreds-of-megahertz range, subject to the complete electrical limits and layout guidance in the manufacturer datasheet. Because the ICS621MIT performs digital fanout rather than voltage conversion, its signal path is intended to preserve clock timing relationships across the four outputs. Low skew is particularly relevant when multiple receivers must operate from the same edge, including parallel data converters, sequential logic, communications equipment, and automated test systems. The exact propagation-delay, output-impedance, rise-time, fall-time, supply-voltage, and temperature limits should be taken directly from the 621 datasheet before final timing and power-budget calculations. Typical uses include clock distribution for communication equipment, fanout in network interfaces, test-and-measurement systems, and synchronization among multiple digital subsystems. It can also serve as an interface between a central clock source and several low-to-moderate-capacitance loads when the board requires a dedicated fanout stage. Its eight-pin package also keeps the footprint compact while exposing one input, four outputs, power connections, and ground in a conventional small-outline arrangement. Layout should prioritize short clock traces, a continuous ground reference, and placement of the device near the clock source or the group of receivers it serves. Avoid routing sensitive clock nets beneath unrelated noisy circuitry, and terminate or control unused outputs according to the manufacturer's guidance. Validate timing at the intended frequency, load capacitance, supply voltage, temperature, and process corner because fanout buffers can change edge rate and edge-to-edge alignment as loading changes. This product page combines the core device identity, verified manufacturer documentation, a same-package replacement candidate, application-oriented engineering guidance, and a structured comparison of the information needed for clock-tree design. It is intended to help engineers identify whether the 1:4, 200 MHz ICS621MIT architecture fits a board before undertaking detailed datasheet verification and board-level qualification.

RFQ Kontak
ICS650G-36 25MHz PCI Clock Generator | Renesas
ICS650G-36

ICS650G-36 25MHz PCI Clock Generator | Renesas

Renesas Electronics ICS650G-36 is a low-cost PCI and networking clock generator with one 25 MHz crystal input and four CMOS clock outputs. It uses analog/digital phase-locked-loop techniques to support LAN, PCI, and 100M SDRAM clock requirements. The device supports PLL bypass operation and is packaged in a 16-pin TSSOP. A clock generator is a timing IC that creates one or more deterministic clock signals for digital systems. Clock and timing ICs sit within the broader semiconductor hierarchy and distribute reference frequencies to processors, memory, network controllers, and bus interfaces. The ICS650G-36 accepts either a crystal or clock input, locks the internal PLL to that reference, and supplies four related output clocks. This arrangement allows one reference source to support several legacy computing and networking clock domains. Key features include a maximum frequency of 25 MHz, one clock circuit, a 1:4 input-to-output ratio, CMOS outputs, and PLL operation with bypass capability. The PLL multiplier allows a 25 MHz fundamental-mode crystal reference to produce four output clocks. Bypass functionality is useful during startup, test, or configurations where direct reference-clock distribution is preferable. The 16-pin TSSOP package supports conventional surface-mount PCB assembly. Internally, the ICS650G-36 combines analog and digital phase-locked-loop techniques with a standard fundamental-mode crystal input. Its architecture is intended to provide multiple clocks from one inexpensive reference while supporting the clocking requirements associated with LAN, PCI, and 100M SDRAM systems. Exact acquisition behavior, output-frequency configuration, voltage limits, and jitter characteristics should be confirmed in the manufacturer datasheet before layout release. Typical applications include legacy PCI peripheral boards, networking equipment, 100M SDRAM memory interfaces, Ethernet controllers, and embedded systems requiring multiple synchronized clock outputs. The four-output arrangement reduces the number of separate oscillators and clock distribution components required on a board. It is particularly relevant to designs based on older PCI and 100M SDRAM architectures rather than modern high-speed server clocking requirements. For implementation, follow the reference circuit and pin-connection details in the manufacturer datasheet, especially for the crystal or external-clock input and unused outputs. Confirm the bypass configuration and output routing for each target bus. PCB signal-integrity practices should include short clock traces, continuous reference planes, and deliberate return paths; CMOS clock outputs also require suitable termination for the selected trace impedance. This product page combines the manufacturer’s application description with verified device attributes, ordering-variant references, a parameter comparison, and practical implementation guidance. It also identifies where additional electrical, environmental, lifecycle, and pin-level information must be checked before production release.

RFQ Kontak
ICS650G-40 Ethernet Switch Clock Source | Integrated Circuit Systems
ICS650G-40

ICS650G-40 Ethernet Switch Clock Source | Integrated Circuit Systems

The Integrated Circuit Systems ICS650G-40 is a clock synthesizer and Ethernet switch clock source with a PLL, crystal or clock input, and clock output. It accepts a 25 MHz crystal input and generates selectable output clock frequencies for Ethernet switch designs. The device is associated with a 1:3 input-to-output ratio, one PLL circuit, and a maximum listed input frequency of 25 MHz. A clock synthesizer is a type of frequency-generation IC used to derive stable timing signals from a common reference. Within the product hierarchy, the ICS650G-40 belongs to the clock and timing IC family, which sits within interface and network-clocking systems. Ethernet switches require multiple related clocks for transceiver interfaces, switching logic, packet processing, and system management. A programmable clock source allows one reference oscillator to support several clock domains while reducing the number of discrete timing components. The principal feature of the ICS650G-40 is its phase-locked-loop architecture. The PLL can divide or multiply the input reference to produce the output frequencies selected through the device's output-select interface. Its 25 MHz reference input provides a common timing foundation for Ethernet switch clock trees. The 1:3 ratio associated with related ICS650G-40 variants provides a useful implementation option when the required system clock is three times the reference frequency. This clock source is intended specifically for Ethernet switch applications rather than general-purpose timing distribution. Its integrated PLL can reduce the number of separate dividers and oscillators needed around a switching ASIC. The 16-TSSOP package identified for related ICS650G-40A variants also reflects a compact surface-mount format appropriate for communications equipment, although engineers should verify the exact land pattern and pin assignment for the ordering code being placed on the PCB. Typical uses include core-clock generation for Ethernet switching silicon, clock-tree support in network interface cards, and timing generation in managed or unmanaged switching platforms. The device can be especially useful where several subsystems must operate from one 25 MHz crystal reference while requiring selectable output-clock options. PCB design should preserve short, clean clock traces and provide a stable reference source with appropriate grounding. Keep sensitive oscillator and PLL traces away from high-current switching nodes, and use the manufacturer pin-description table to assign every signal correctly. Confirm output frequency, enable behavior, supply requirements, and load capability against the datasheet before releasing a production layout. This product page combines the Ethernet clock-source function, PLL characteristics, package considerations, application guidance, and substitution constraints into an engineering-focused guide. It also distinguishes verified drop-in candidates from suffix-only ordering options that should not be assumed to be interchangeable without package and pin verification.

RFQ Kontak
ICS650R-01 - 66.67MHz PLL Clock Synthesizer | Renesas
ICS650R-01

ICS650R-01 - 66.67MHz PLL Clock Synthesizer | Renesas

The Renesas Electronics ICS650R-01 is a clock and frequency synthesizer IC that generates up to 66.67 MHz from a 14.31818 MHz parallel-resonant crystal reference. It uses analog and digital phase-locked-loop techniques, includes PLL bypass capability, and provides a CMOS output in a 20-pin SSOP package measuring 3.90 mm wide. The device is intended for system-peripheral clocking and other applications requiring a stable, low-jitter reference-derived clock. A clock synthesizer is an integrated timing device that converts a lower-frequency reference into one or more higher-frequency signals. Clock synthesizers commonly use a phase-locked loop, or PLL, to lock a voltage-controlled oscillator to an external crystal or clock source. Within the broader semiconductor hierarchy, the ICS650R-01 belongs to the clock and timing IC family, where it provides frequency multiplication and clock-distribution functions for digital systems. The principal features of the ICS650R-01 include a maximum output frequency of 66.67 MHz, support for either crystal or clock input, CMOS output signaling, and a PLL with bypass. The 14.31818 MHz reference associated with this device is the classic frequency used for NTSC-related timing systems. The PLL architecture allows the output to be derived from a stable crystal source while retaining bypass flexibility for test and clock-source transition scenarios. The ICS650R-01 uses phase-locked-loop techniques to establish the relationship between its reference input and synthesized output. The bypass function gives a system designer an alternate clock path when direct use of the source clock is preferable. Because the output is CMOS and reaches 66.67 MHz, board-level implementation requires careful attention to trace impedance, return paths, ground integrity, and clock-edge margin. The 20-pin SSOP footprint supports conventional surface-mount assembly and is suitable for compact peripheral-clock circuitry. Typical applications include legacy video and display timing, computer and peripheral clock generation, communication equipment, industrial control systems, and digital logic requiring a derived clock from a crystal source. The ICS650R-01 is particularly relevant to retrofits and repairs of equipment designed around the 14.31818 MHz reference and 66.67 MHz synthesized output. Its CMOS output can feed compatible counters, divider stages, timing controllers, and other clock-domain logic when voltage and frequency requirements are met. Design should begin by confirming the required reference frequency, output frequency, output amplitude, load capacitance, supply voltage, and operating-temperature range against the manufacturer datasheet. Place the crystal and associated load network close to the clock input, maintain a continuous ground reference beneath clock circuitry, and avoid routing the sensitive reference node beside switching nodes. Because no complete operating electrical table or timing characteristics are stated on the product listing, those limits must be taken directly from the manufacturer datasheet before production release. This product page combines the documented clock-source function, package information, replacement guidance, application-oriented engineering context, and a package-matched comparison framework. It also distinguishes electrically similar ordering variants from confirmed alternatives, helping designers identify the correct device without relying solely on a clock frequency or package name.

RFQ Kontak
ICS650R-07 - Low-Jitter Networking Clock Source | Renesas
ICS650R-07

ICS650R-07 - Low-Jitter Networking Clock Source | Renesas

The Renesas Electronics ICS650R-07 is a low-cost, low-jitter, high-performance system-peripheral clock synthesizer for networking equipment, supplied in a 20-SSOP package. It accepts a 14.31818 MHz parallel-resonant crystal reference and uses analog and digital phase-locked-loop techniques to generate the clock required by system peripheral circuitry. The device is described as a networking clock source in distributor catalogs and as a system-peripheral clock source in technical documentation. A clock synthesizer, also called a PLL clock generator, produces one or more stable frequencies from a single reference crystal. Its position in the signal chain is oscillator or crystal reference to clock synthesizer to digital logic clock distribution. This hierarchy makes the ICS650R-07 useful when a board needs a defined internal clock rather than a free-running digital oscillator, especially in legacy network-interface, storage, controller, and communications equipment. The primary advantages of the ICS650R-07 are its low cost, low jitter, and high-performance PLL-based frequency generation. Its 14.31818 MHz crystal input supports designs built around the standard parallel-resonant reference commonly associated with communications clock architectures. The 20-SSOP package is compact enough for established peripheral-controller layouts while remaining a surface-mount part suitable for automated assembly. The manufacturer documentation also identifies an ICS650-07B derivative customized for Broadcom applications, indicating a related clock-source family with different ordering and qualification options. Internally, the device combines analog and digital phase-locked-loop techniques rather than relying on a simple frequency multiplier with free-running outputs. PLL-based synthesis allows the output frequency to be referenced to the external crystal, which supports repeatable clock generation across temperature and supply conditions. Exact operating ranges, frequency tolerances, jitter limits, supply voltage, and output-drive details must be taken from the manufacturer datasheet for the specific ordering code before release qualification. Typical uses include networking-interface clock trees, system-peripheral controllers, communications modules, and legacy server or storage peripheral boards. It is particularly relevant when the PCB already accepts a 20-SSOP clock-source position and requires a reference-derived peripheral clock. For new designs, engineers should confirm that the crystal frequency, target PLL output, loop-filter configuration, and decoupling requirements match the intended system architecture rather than treating the part as a generic free-running oscillator. The principal design constraint is that the ICS650R-07 is an older clock-source family rather than a modern low-power clock generator. Its lifecycle, operating-temperature grade, and RoHS status require review for regulated or new-production programs. A legacy board can often retain its existing crystal and PLL component arrangement, but a redesign should compare phase noise, jitter, supply current, maximum frequency, and qualification status against current clock-generator families. This page organizes the clock-source role, package details, verified catalog information, drop-in family alternatives, and application guidance in one engineering-focused reference. It also distinguishes device functions that can be confirmed from the manufacturer datasheet from parameters that require a full engineering review before schematic release or production qualification.

RFQ Kontak
ICS650R-12 MPEG Clock Synthesizer | Renesas Electronics
ICS650R-12

ICS650R-12 MPEG Clock Synthesizer | Renesas Electronics

The Renesas Electronics ICS650R-12 is an MPEG clock synthesizer for system-peripheral clock generation, with a 14.31818 MHz crystal input and clock output in a 20-pin SSOP package. It uses analog and digital phase-locked loop techniques to generate the timing signals required by MPEG and related digital systems. The device is specified as a low-cost, low-jitter, high-performance clock synthesizer with one clock synthesis circuit, surface-mount construction, and an operating temperature range of 0°C to 70°C. A clock synthesizer is a timing IC that converts a stable reference frequency into one or more derived clock signals. Clock synthesizers and PLL-based timing devices form part of the clock and timing hierarchy within integrated circuits, where they sit between a crystal or oscillator reference and the digital logic requiring synchronized system clocks. The ICS650R-12 family is intended for system-peripheral applications, making its reference frequency, output behavior, and board footprint the principal design considerations. Key characteristics include one clock-generation circuit, a crystal-based reference input, clock output, low-jitter operation, and a 20-pin SSOP package. Its surface-mount construction supports compact consumer and industrial equipment designs, while the specified 0°C to 70°C operating range makes it appropriate for room-temperature commercial environments. The MPEG designation identifies its intended timing role, while the PLL architecture provides frequency multiplication and clock-generation flexibility relative to a simple buffered crystal oscillator. The ICS650R-12 is identified as an obsolete or end-of-life component. New production should therefore be approached cautiously, while existing equipment may require a form-fit-function replacement or a deliberate clock-tree redesign. Because the device is no longer active, engineers should confirm lifecycle status, electrical limits, pin mapping, crystal requirements, and output timing before committing a replacement to production. Typical uses include MPEG decoder and encoder platforms, multimedia processing systems, digital set-top equipment, and other system-peripheral subsystems requiring a synthesized clock. In these systems, the crystal reference establishes the timing foundation while the synthesizer distributes a stable derived clock to processors, memory interfaces, converters, and other clock-consuming blocks. This integration reduces the number of separate oscillators required in a multi-clock design. PCB implementation requires close attention to the 20-pin SSOP footprint, crystal support components, trace lengths, and grounding. Place the reference-crystal network near the device, keep clock traces short, maintain a continuous ground reference, and follow the manufacturer pin-description table when assigning every connection. Review the obsolete-part notices and cross-reference tools before redesigning around a different PLL or clock generator. This page consolidates lifecycle information, confirmed device characteristics, practical application guidance, and verified replacement constraints. It also separates known specifications from parameters that require confirmation from the manufacturer datasheet, helping engineers make an informed sourcing or redesign decision for this legacy MPEG clock synthesizer.

RFQ Kontak
ICS651M - 1:4 200MHz Clock Fanout Buffer | Renesas
ICS651M

ICS651M - 1:4 200MHz Clock Fanout Buffer | Renesas

The Renesas Electronics ICS651M is a 1:4 clock fanout buffer distribution IC designed for clock signals up to 200 MHz, supplied from 1.425 V to 2.625 V and packaged in an 8-SOIC. Its single clock input feeds four clock outputs, making it useful when several digital subsystems must receive a common timing reference. A clock fanout buffer is a clock and timing IC that reproduces one input clock across multiple outputs. It belongs to the clock distribution hierarchy, where a buffer preserves edge-driven timing while increasing fanout, isolating source loading, and giving short, controlled routes to multiple receivers. Unlike a frequency-changing oscillator or PLL, the ICS651M does not create a new frequency; it distributes the supplied clock and is intended to maintain low-skew operation. The principal verified features are the 1:4 fanout ratio, 200 MHz maximum operating frequency, clock input and clock outputs, and 1.425 V to 2.625 V supply range. The 8-SOIC package measures 0.154 inches, or 3.90 mm, in width. These values position the part as a compact, low-voltage clock distribution solution where four copies of one clock are required rather than programmable or multiplied clock synthesis. Use the ICS651M after a stable clock source when the next circuit stages would otherwise load a single output excessively or require long branches to remote logic. Equalizing trace geometry and keeping the input and output return paths close to a continuous ground plane can help control propagation-delay differences among outputs. Engineers must also verify downstream input thresholds, output timing at the actual operating frequency, and termination requirements for each clock network. Typical uses include coordinating clock domains in processors, FPGAs, communications equipment, test systems, and digital control logic. The device may be particularly useful where one low-voltage master clock must reach four independent loads without repeatedly branching a long net. Because its verified maximum frequency is 200 MHz, timing margins should be evaluated at the highest intended edge rate rather than relying only on the nominal operating frequency. Place all four clock outputs into controlled PCB routes, avoid long stub traces, and provide a low-impedance return path beneath every clock edge. If unused outputs are left unconnected, their exact treatment should be confirmed from the manufacturer datasheet. Decoupling, output enable, and input-standby behavior were not included in the supplied search evidence and must be checked before layout approval. This page consolidates verified distributor specifications, sourcing links, application context, and design cautions. Where primary documentation was unavailable in the supplied data, unknown electrical details remain explicitly marked rather than being estimated.

RFQ Kontak
ICS651MI - 1:4 200 MHz Clock Fanout Buffer | Renesas Electronics
ICS651MI

ICS651MI - 1:4 200 MHz Clock Fanout Buffer | Renesas Electronics

The Renesas Electronics ICS651MI is a low-skew, single-input to four-output clock fanout buffer rated for operation up to 200 MHz, supplied in an 8-SOIC package. Its 1:4 fanout ratio provides one clock distribution function for driving four downstream destinations, while its 1.425 V to 2.625 V supply range supports low-voltage digital clocking systems. The verified distributor and technical listings identify the device as a Clock Fanout Buffer (Distribution) IC with clock input and clock outputs. A clock fanout buffer is a clock-and-timing IC that receives one periodic signal and produces multiple buffered copies. It belongs to the broader clock-buffer and clock-driver hierarchy, where buffers are used to extend fanout, isolate a source from downstream loading, reduce edge-rate degradation, and distribute a common timing reference. The ICS651MI therefore serves as an interface between a clock source and several digital loads rather than as a frequency-generating or phase-locked-loop device. The principal verified specifications are a 1:4 fanout ratio, a maximum operating frequency of 200 MHz, a 1.425 V to 2.625 V supply-voltage range, and an 8-SOIC package measuring 3.90 mm in width. The low-skew description indicates that the device is intended to preserve close timing relationships among its four outputs. This makes it potentially useful in communications, processor systems, test equipment, and other clocked digital equipment when one source must feed several destinations. The ICS651MI uses a clock input and four clock outputs, providing eight functional connections in the 8-SOIC package. The public search results supplied for this product do not expose the complete numbered pin assignments, enable controls, output-drive strength, propagation-delay limits, or detailed electrical characteristics. Those values must therefore be confirmed against the manufacturer datasheet before layout or timing-signoff work. Renesas provides an official ICS651MI family datasheet page at the URL included in this record. Typical applications include four-way clock distribution within communications equipment, fanout for processor or logic clock trees, clock buffering in industrial control systems, and synchronized distribution to multiple digital peripherals. In each case, the 200 MHz maximum frequency and four outputs are the main selection criteria. The designer should also verify input and output capacitance, supply tolerance, output enable behavior, and package-level timing data because those details are not present in the verified excerpts supplied here. A key design consideration is that a buffer does not remove all timing uncertainty from the downstream system. Trace lengths, load capacitance, supply noise, and clock-tree topology can still affect edge arrival times. Place the buffer close to the clock source, keep output routing topology consistent where skew matters, and use controlled-impedance routing when outputs drive transmission lines. Confirm that every downstream receiver meets the available amplitude, slew-rate, and timing requirements at the selected operating frequency. This page consolidates the verified distributor listings, manufacturer datasheet reference, package information, electrical envelope, and practical selection considerations for ICS651MI. It also distinguishes directly verified facts from unavailable electrical details and avoids presenting unverified cross-references as drop-in replacements. The resulting guidance is intended to support initial design selection, sourcing, and datasheet review without substituting for schematic-level timing and signal-integrity validation.

RFQ Kontak
ICS651MIT - 1-to-4 200 MHz Clock Buffer | Renesas
ICS651MIT

ICS651MIT - 1-to-4 200 MHz Clock Buffer | Renesas

Renesas Electronics ICS651MIT is a low-skew 1-to-4 fanout clock buffer with a maximum operating frequency of 200 MHz and a supply-voltage range of 1.425 V to 2.625 V. The device is packaged in an 8-SOIC measuring 3.90 mm wide and is designed to distribute one input clock across four outputs while limiting output-to-output timing skew. A clock fanout buffer is a clock-and-timing integrated circuit that replicates a periodic signal to multiple destinations. Within the broader semiconductor hierarchy, it belongs to clock and timing ICs, then clock buffers and drivers, and ultimately digital logic. Unlike a clock generator, it does not create a new reference frequency; instead, it buffers an existing clock so multiple circuits can receive controlled copies with predictable timing relationships. The primary features of ICS651MIT are its 1-to-4 fanout architecture, 200 MHz maximum frequency, and 1.425 V to 2.625 V operating supply range. These characteristics make it suitable for low-voltage digital systems that need to distribute a common clock among processors, memory controllers, communication circuits, or custom logic. Its low-skew design helps limit the difference in arrival time between the four buffered outputs. ICS651MIT belongs to the ICS ClockBlocks family and is positioned as a small, low-skew clock buffer. The 8-SOIC package provides a compact surface-mount implementation for applications that do not require the zero-delay or PLL-based functions offered by more complex clock products. Each buffered output should be treated as a separate clock load, so trace length, loading, and downstream capacitance remain important considerations. Typical uses include clock distribution in communications equipment, digital logic subsystems, processor clock trees, and embedded control systems. In a multi-destination design, the single clock input can feed four independently routed outputs, reducing duplicated clock-generation circuitry. The part is especially relevant where several sequential circuits must operate from the same timing reference on a low-voltage supply. Layout quality directly affects clock integrity in a fanout network. Place the input and output decoupling capacitors close to their associated pins, keep output routes short where possible, and avoid routing clock signals through noisy analog or switching-power regions. Maintain a continuous return path beneath or adjacent to each clock trace and observe the device's recommended input and output loading limits from the manufacturer datasheet. This product page organizes the core electrical characteristics, package information, application guidance, datasheet access, and design considerations for ICS651MIT. It also identifies where replacement verification requires a direct comparison of pinout, supply voltage, frequency, output behavior, and propagation delay before any substitute is approved for production.

RFQ Kontak
ICS651MT - 200MHz 1:4 Clock Buffer | Renesas | 8-SOIC
ICS651MT

ICS651MT - 200MHz 1:4 Clock Buffer | Renesas | 8-SOIC

The Renesas Electronics ICS651MT is a 1:4 fanout clock buffer with a maximum operating frequency of 200 MHz, a 1.425 V to 2.625 V supply-voltage range, and an 8-pin SOIC package. The device accepts one clock input and provides four buffered clock outputs, making it suitable for distributing a low-frequency clock across multiple digital, communications, or embedded-system loads. A clock buffer, also called a clock driver or fanout buffer, is a digital timing IC that reproduces an input clock onto multiple outputs with controlled propagation delay and low output-to-output skew. Clock buffers belong to the clock and timing hierarchy, alongside clock generators, phase-locked loops, jitter cleaners, dividers, and delay lines. Their purpose is to restore signal integrity, isolate the source from capacitive loading, and provide matched clock branches in systems where a single clock cannot directly drive every destination. The ICS651MT is identified as a low-skew, single-input, four-output clock buffer in the ICS ClockBlocks family. Verified specifications list a maximum frequency of 200 MHz, a 1.425 V to 2.625 V supply range, 250 ps skew, and a commercial operating-temperature range of 0 C to 70 C. Its four-output architecture supports economical distribution without implementing four separate discrete buffers. The SOIC-8 package also supports conventional surface-mount manufacturing and inspection processes. Operationally, the buffer preserves the clock waveform while adding fanout capability. The verified datasheet guidance specifies a 0.01 uF decoupling capacitor between VDD on pin 7 and GND on pin 6, placed as close to the device as possible. It also states that a 33 ohm series terminating resistor may be used on each clock output when the trace is longer than 1 inch. These recommendations reduce supply-noise coupling, ringing, and reflections on longer clock routes. Typical uses include processor-clock distribution in embedded equipment, communication-interface clock fanout, general-purpose logic clock distribution, and fanout for digital converters or controllers. Because this is a four-output buffer rather than a clock generator, an external clock source is required. The source must provide a valid clock waveform within the device's specified frequency and supply-voltage limits, and each connected load must be checked for timing margin. The primary design trade-off is output loading versus timing margin. Short, lightly loaded traces may not need source termination, while long PCB routes can develop edge reflections that reduce setup and hold margin. Place the decoupling capacitor at the supply pins, use short output branches, and evaluate rise time, fanout, and skew at the actual operating frequency before releasing the layout. This product page consolidates the verified clock-buffer specifications, application guidance, comparison fields, and practical implementation notes. It distinguishes documented electrical and packaging data from unavailable lifecycle, pricing, and pinout details so engineers can make sourcing decisions without treating unverified values as established facts.

RFQ Kontak
ICS660GI - NTSC/PAL Video Clock Generator | Renesas
ICS660GI

ICS660GI - NTSC/PAL Video Clock Generator | Renesas

The Renesas Electronics ICS660GI is a digital video clock source and video generator IC for NTSC and PAL systems, supplied in a 16-pin TSSOP package. It provides clock generation and conversion for digital video equipment, including formats associated with MPEG, NTSC, PAL, and HDTV video timing. The ICS660GI is intended for designers requiring a dedicated timing source for video processing, synchronization, and conversion circuits. Its 16-TSSOP package supports compact PCB layouts in professional video, broadcast, industrial imaging, and test equipment designs. A digital video clock source is a timing IC that generates or converts clock signals used to synchronize video processing blocks. Digital video systems require consistent horizontal and vertical timing across multiple functional stages. The ICS660GI belongs to the broader clock and timing IC hierarchy, where clock generators and frequency converters support video timing, clock distribution, and signal-chain synchronization in electronic equipment. The principal application feature is support for NTSC and PAL video signal generation. These standards require stable timing relationships between synchronization, blanking, active video, and related control signals. The ICS660GI is used where a board-level clock and timing reference is needed rather than a general-purpose microcontroller timer. Its dedicated video timing role can simplify clock distribution and reduce the timing burden placed on a system processor. ICS660GI is identified as a video generator IC with NTSC and PAL support, and it is also described as a digital video clock source. These descriptions reflect its role in digital video clock generation and conversion. The component is associated with clock rates commonly required in MPEG, NTSC, PAL, and HDTV equipment, making it relevant to legacy and specialized video systems where the correct standard and synchronization behavior are more important than a generic low-cost oscillator. The 16-TSSOP package is a surface-mount package with compact lead spacing suitable for modern board assembly. Because the manufacturer datasheet and complete pin-description table are not included in the available product references, engineers should verify pin assignments, voltage ratings, operating frequency, output configurations, and timing tolerances against the current Renesas datasheet before releasing a production design. This page focuses on the function and sourcing facts identified for the exact ICS660GI ordering code. This page combines the verified product description, NTSC/PAL and digital-video timing context, package information, sourcing guidance, and practical design notes. It is intended to help engineers determine whether ICS660GI fits a video timing requirement before requesting a quote for the exact 16-TSSOP device.

RFQ Kontak
ICS661GI - 73.728MHz Audio Clock Source | Renesas | TSSOP-16
ICS661GI

ICS661GI - 73.728MHz Audio Clock Source | Renesas | TSSOP-16

Renesas Electronics ICS661GI is a precision audio clock generator and clock synchronizer IC with a 73.728 MHz output, supplied in a 16-pin TSSOP package measuring 4.40 mm wide. The device generates synchronous audio sampling clocks derived from an MPEG stream and can also serve as a standalone clock source using a 27 MHz crystal. A clock generator is a timing IC that converts a reference input into one or more stable clock outputs. Clock generators and clock synchronizers form part of the broader clock and timing IC family, where they support digital audio, communications, data conversion, and embedded signal-processing systems. The ICS661GI is intended specifically for precision audio-clock generation, providing a defined output associated with common digital-audio sampling rates. Its principal documented characteristics include a 73.728 MHz clock output, support for a standalone 27 MHz crystal reference, and a compact 16-pin TSSOP package. The narrow 4.40 mm package width supports conventional surface-mount PCB assembly while reducing the footprint compared with larger clock packages. The manufacturer categorizes the component as a clock generator, clock synchronizer IC for precision audio applications. The ICS661 architecture supports two operating approaches. In MPEG-derived operation, it produces synchronous audio sampling-clock rates from an MPEG stream. In standalone operation, it uses a 27 MHz crystal as the timing reference. This flexibility allows the same device to be evaluated in systems where the upstream source is digital media data or where a local crystal-backed clock is preferred. Typical uses include digital audio equipment, MPEG audio processing chains, audio codecs and converters, consumer electronics, and clock-distribution subsystems requiring a dedicated audio-rate source. System designers should evaluate the device against the required audio sampling rate, reference architecture, output jitter, supply conditions, and acquisition format before finalizing the clock tree. Place the ICS661GI close to the clock-consuming circuit and observe the grounding and decoupling guidance in the Renesas ICS661 datasheet. The 16-pin TSSOP footprint requires a deliberate escape-routing pattern, and unused inputs should be connected according to the manufacturer’s recommended input states. Differential pair routing and controlled return paths are preferable when the output drives a sensitive converter or high-speed digital input. This product page consolidates the clock function, package details, application fit, replacement considerations, and implementation guidance. It also distinguishes documented electrical facts from parameters that require confirmation in the complete manufacturer datasheet, helping engineers plan sourcing and PCB design before committing to a production build.

RFQ Kontak
ICS663M - 120MHz PLL Clock Synthesizer | Renesas Electronics
ICS663M

ICS663M - 120MHz PLL Clock Synthesizer | Renesas Electronics

Renesas Electronics ICS663M is a single-circuit phase-locked-loop clock synthesizer with a maximum operating frequency of 120 MHz, a 1:1 input-to-output ratio, and CMOS clock output. The device is supplied in an 8-SOIC surface-mount package measuring 3.90 mm wide and is listed for operation from 3.13 V to 5.5 V. A phase-locked loop, or PLL, is a frequency-control building block that locks an internally generated or controlled clock to a reference signal. Within the clock and timing hierarchy, the ICS663M functions as a PLL building block combining a phase detector, charge pump, voltage-controlled oscillator, and output buffer. This allows an external timing loop to synthesize or synchronize a stable CMOS clock rather than relying only on a free-running oscillator. The verified product information identifies the ICS663M as a low-cost PLL intended for clock synthesis and synchronization. Its principal documented parameters include one PLL circuit, one clock input, one CMOS output, no differential input or output, a 1:1 input-to-output division ratio, and operation up to 120 MHz. The 8-SOIC package provides a compact surface-mount option for clock-generation and timing circuits. The PLL architecture makes external loop filtering an important part of the application circuit. External components can establish loop bandwidth, damping, and phase-error behavior, which influence jitter, acquisition time, and reference-clock rejection. Actual performance therefore depends on the external loop network, reference frequency, output loading, supply quality, and board layout rather than only on the nominal 120 MHz maximum. Typical applications include reference-clock multiplication, synchronization of communications equipment, generation of a derived system clock, and recovery or conditioning of a timing signal. The ICS663M is also suitable for industrial instrumentation, test equipment, and embedded systems that require a phase-locked CMOS clock but do not require a highly integrated programmable clock generator. Designers should provide stable supply and reference-clock connections, follow the manufacturer’s recommended loop-filter topology, and use short return paths for clock and ground. Because an 8-SOIC footprint is compact, trace geometry and capacitance control become important when maintaining signal integrity at higher clock rates. This page combines verified distributor and manufacturer-linked product information with practical PLL design guidance, transparent comparison data, and availability details. It distinguishes documented parameters from engineering values that still require confirmation from the Renesas datasheet before schematic release or production qualification.

RFQ Kontak
ICS663MI - PLL Clock Driver Building Block | Renesas | 8-SOIC
ICS663MI

ICS663MI - PLL Clock Driver Building Block | Renesas | 8-SOIC

Renesas ICS663MI is an integrated PLL building block packaged in an 8-pin SOIC, a surface-mount package measuring 3.90 mm wide. The component belongs to the clock and timing semiconductor family and is intended for clock-generation, clock-distribution, and frequency-synthesis systems. The verified product information identifies it as an IC PLL building block and lists the package as 8-SOIC. A PLL building block is a timing IC used within a phase-locked-loop architecture. Its function is to support a feedback-controlled oscillator whose output frequency can be related to a reference frequency. Clock-generation and PLL-based frequency synthesis are part of the broader clock and timing hierarchy, which also includes clock buffers, clock drivers, dividers, oscillators, and frequency multipliers. These devices establish the timing reference used by processors, communications equipment, data converters, and digital control systems. The defining physical characteristic of the ICS663MI is its 8-SOIC package with a stated width of 0.154 inch, or 3.90 mm. Surface mounting supports compact PCB construction and automated assembly. Renesas Electronics America Inc is identified as the manufacturer associated with the listed MPN, while legacy catalog records associate the part with Integrated Device Technology, Inc. The MI package suffix is treated as the manufacturer ordering code shown in the available listings. The ICS663MI belongs to a timing-device category where exact operating limits must be established from the manufacturer datasheet before implementation. Input and output frequency ranges, supply voltage, operating temperature, phase noise, jitter, output configuration, and input-to-output ratio are not stated in the available product records. Those electrical parameters must be checked in the datasheet rather than inferred from the PLL building-block description. The package dimensions are known, but land-pattern and solder-reflow details also require manufacturer guidance. Typical design roles for this device family include clock synthesis, reference distribution, communications timing, digital-system clock trees, and frequency conversion. In each case, the PLL is used to create or organize a stable timing relationship between a reference and an output clock. Whether the ICS663MI can support a particular channel rate, loop filter, output standard, or synchronization scheme depends on its detailed electrical characteristics and recommended application configuration. Before layout, check the complete pin description and recommended decoupling network in the manufacturer datasheet. Keep the clock and feedback routing compact and controlled, and account for jitter and noise budget rather than treating the PLL solely as a frequency multiplier. PCB power and ground distribution, loop-filter component placement, and output-load compatibility are central to achieving predictable clock performance. This product page combines the verified package and device-class information with practical selection guidance, comparison fields, sourcing questions, and design considerations. It separates confirmed facts from parameters that require datasheet confirmation, helping engineers determine whether the ICS663MI belongs in a clock-timing design before requesting a quote or beginning layout.

RFQ Kontak
ICS663MLF - 120MHz PLL Clock Synthesizer | Renesas
ICS663MLF

ICS663MLF - 120MHz PLL Clock Synthesizer | Renesas

The Renesas Electronics ICS663MLF is a low-cost phase-locked-loop clock synthesizer designed for clock synthesis and synchronization, with operation up to 120 MHz and operation from a 3.3 V supply in an 8-pin SOIC package. The integrated circuit combines a phase detector, charge pump, voltage-controlled oscillator, and output buffer in one compact device, providing the core functions required for generating a clock from an external reference. A phase-locked loop, or PLL, is a feedback-control circuit that locks an internally generated oscillator to an external reference signal. In the clock-and-timing hierarchy, a PLL clock synthesizer belongs to the broader clock generator and frequency-synthesizer family. It is used when a system needs a stable, programmable clock derived from a reference rather than a free-running oscillator. The ICS663MLF supports synchronization applications in which phase, frequency, and output stability determine downstream timing quality. The principal device characteristics include a maximum clock frequency of 120 MHz, a 3.3 V operating supply identified in the product listing, and an 8-SOIC package. The SOIC package provides a standard surface-mount form factor suitable for conventional PCB assembly. The MLF ordering suffix is associated with tube packaging, allowing the same device to be ordered in a production-friendly bulk format. The 8-pin arrangement also reduces board area compared with larger clock-generator packages while retaining access to the PLL’s principal external connections. Technically, the phase detector compares the reference and feedback signals, while the charge pump converts the detected phase error into a control voltage. The voltage-controlled oscillator uses that control voltage to generate an output whose frequency is divided and fed back to complete the locking loop. External reference and VCO dividers expand the range of input and output frequencies that can be synthesized. The manufacturer description specifically notes that divider implementations such as the ICS674-01 can be used to configure the ICS663 for a broad range of input frequencies. Typical uses include clock generation for digital logic, synchronization of multiple circuit domains, frequency synthesis in communications equipment, and distributed clocking in industrial or embedded systems. A design should preserve the loop-filter layout and provide clean reference and feedback signals because phase jitter and reference noise propagate directly to the generated clock. Component selection also requires checking the exact output frequency range, reference-input limits, supply tolerance, and external divider values against the manufacturer’s operating table. The key implementation consideration is to use the PLL in its intended reference-and-feedback topology rather than treating it as a free-running oscillator. Place the loop-filter components near the relevant device pins, route the feedback path away from high-current switching nodes, and use a low-jitter reference clock when precise downstream timing is required. Component values and loop bandwidth should follow the manufacturer’s application guidance. This product page combines the device architecture, package information, sourcing guidance, drop-in alternatives, application context, and practical PCB recommendations in one engineering-focused reference. The result helps designers evaluate the ICS663MLF for synchronization and frequency-synthesis designs while identifying where a different PLL family member or a new PCB design is required.

RFQ Kontak
ICS663MT - 120MHz CMOS PLL | Renesas | Clock & Timing
ICS663MT

ICS663MT - 120MHz CMOS PLL | Renesas | Clock & Timing

Renesas Electronics ICS663MT is a low-cost phase-locked-loop clock synthesis and synchronization building block with a maximum operating frequency of 120 MHz, one PLL circuit, CMOS output, and an 8-SOIC package. The device integrates a phase detector, charge pump, voltage-controlled oscillator, and output buffer to support clock generation and synchronization functions. Its 1:1 input-to-output ratio identifies it as a non-differential clock PLL rather than a frequency-multiplying synthesizer. A phase-locked loop is a feedback-controlled timing circuit that locks a voltage-controlled oscillator to a reference clock. In the broader semiconductor hierarchy, the ICS663MT belongs to the clock and timing IC family, where PLL building blocks synchronize oscillators, regenerate or distribute clock signals, and reduce timing differences between related circuit domains. The ICS663MT specifically provides the phase-detection and feedback functions needed to establish a stable relationship between an input clock and its generated output. The principal documented characteristics are a 120 MHz maximum frequency, one PLL circuit, a 1:1 input-to-output ratio, CMOS output signaling, and no differential input or differential output. These specifications make the ICS663MT relevant to designs requiring a single-ended clock relationship, including communications equipment, clock-distribution modules, frequency-standard interfaces, and legacy digital systems. The 8-SOIC outline supports conventional surface-mount assembly, although final board compatibility must be confirmed against the exact pin configuration. Technically, the PLL architecture compares the incoming clock with a feedback signal, drives the charge pump from the phase-error information, and adjusts the voltage-controlled oscillator until the loop approaches lock. The external components and loop-filter requirements should therefore be taken directly from the manufacturer datasheet. Because the available device summary does not state the complete input-frequency range, lock range, jitter, supply voltage, or operating-temperature limits, those characteristics should not be inferred from the 120 MHz headline value. Typical clock-synchronization uses include recovering a coherent timing relationship in communications equipment, distributing a system reference to one internal clock domain, and supporting laboratory or industrial timing modules. The non-differential interface is particularly useful where the source and destination use single-ended CMOS clocks. Conversely, systems requiring differential clock I/O, programmable multiplication, fractional synthesis, or a known higher-ratio architecture need a different PLL family. Before layout, confirm the pin names, exposed connections, supply requirements, and recommended loop filter in the manufacturer datasheet. Place the PLL close to the clock source and sensitive clock-consuming circuitry, route outputs as short as practical, and maintain a continuous ground reference. Avoid introducing long stubs or uncontrolled impedance discontinuities into clock traces because they can degrade edge quality and timing margin even when the nominal operating frequency is acceptable. This product page consolidates the documented architecture, operating frequency, ratio, interface type, package outline, design guidance, and sourcing workflow for engineers evaluating the ICS663MT. It also distinguishes confirmed characteristics from parameters that require confirmation during component review, helping teams assess fit, board compatibility, and supply continuity before committing to a production design.

RFQ Kontak
ICS722M - 28MHz 3.3V CMOS VCXO | Renesas Electronics
ICS722M

ICS722M - 28MHz 3.3V CMOS VCXO | Renesas Electronics

Renesas Electronics ICS722M is a 28 MHz voltage-controlled crystal oscillator, or VCXO, with a 3.3 V power supply, CMOS output, and 8-pin SOIC surface-mount package. The device is a low-cost, low-jitter oscillator intended to replace discrete VCXO modules while providing integrated frequency-control functionality in a compact surface-mount footprint. Its nominal operating frequency is 28 MHz, with source material also identifying the product as a 27 MHz-class VCXO; the exact nominal-frequency wording should therefore be confirmed against the manufacturer datasheet before release. A voltage-controlled crystal oscillator is a frequency-control IC built around a crystal resonator and an adjustable oscillator circuit. A VCXO belongs to the broader oscillator hierarchy, which includes crystal oscillators, frequency dividers, clock generators, phase-locked loops, and timing ICs. Unlike a fixed-frequency crystal oscillator, a VCXO permits its output frequency to be adjusted within a manufacturer-specified control range, making it useful when small frequency corrections are required for clock synchronization, filtering, or signal conversion. The supplied product information identifies the ICS722M as a low-cost, low-jitter, high-performance 3.3 V VCXO with a CMOS output. It is available in an 8-SOIC package and is listed in tube packaging by one distributor. Its single-oscillator architecture supports applications requiring one independently adjustable clock rather than a multi-output PLL or clock-generator network. The 3.3 V supply operation also allows integration with 3.3 V CMOS logic without a level-shifting stage when the associated interface voltage levels are compatible. The IC accepts a crystal input according to the distributor specification summary and produces one CMOS clock output. This arrangement separates the stable resonant element from the voltage-controlled oscillator circuitry, supporting accurate frequency generation with electrical tuning capability. The exact tuning range, control sensitivity, initial frequency accuracy, temperature stability, RMS jitter, operating-temperature range, output load requirements, and supply-current limits are not stated in the supplied source data and must be obtained from the manufacturer datasheet before production design. Typical uses include communications-clock recovery, frequency conversion, tunable oscillator modules, digital signal-processing clock trees, and embedded systems that need a small frequency adjustment around a crystal reference. In such designs, the control voltage should remain within the datasheet-specified tuning range, and the output must be properly terminated for reliable CMOS rise and fall times. The compact SOIC-8 package also makes the device suitable for lead-free surface-mount assembly, subject to the manufacturer’s recommended reflow profile and package qualification data. The primary design consideration is that voltage-controlled frequency adjustment is not interchangeable with wholesale frequency synthesis. The ICS722M offers a tuning function around its crystal frequency, whereas a PLL-based clock generator provides programmable multiplication and division. Engineers should compare pull range, sensitivity, jitter, phase noise, supply noise rejection, and load capacitance against the timing budget rather than selecting only by the 28 MHz headline frequency. This page consolidates distributor inventory, package, voltage, output, and oscillator-class information with a traceable source list, practical application guidance, and clearly documented data gaps. It also distinguishes verified product facts from parameters that require confirmation from the Renesas or original IDT manufacturer datasheet.

RFQ Kontak
ICS722MT - 28MHz 3.3V Low-Jitter VCXO | Renesas Electronics
ICS722MT

ICS722MT - 28MHz 3.3V Low-Jitter VCXO | Renesas Electronics

The Renesas Electronics ICS722MT is a 28 MHz voltage-controlled crystal oscillator (VCXO) IC designed for low-cost, low-jitter frequency-control applications in a 3.3 V power environment. The device accepts a crystal input and provides a CMOS output, with a maximum frequency of 28 MHz and an input-to-output ratio of 2:1. It is packaged in an 8-pin SOIC, making it suitable for compact communications, timing, and clock-generation designs that require adjustable frequency control rather than a fixed-frequency oscillator. A VCXO is a crystal-based oscillator whose output frequency can be varied with an external control voltage. In the broader electronics hierarchy, a VCXO is a frequency-control IC and a specialized form of oscillator, while also belonging to the clock and timing component family. It is commonly used when a system needs a modest frequency correction, tuning, or synchronization capability that a conventional fixed-frequency crystal oscillator cannot provide. The ICS722MT combines a 3.3 V operating design with CMOS output and an integrated voltage-controlled crystal oscillator architecture. Its stated purpose is to replace expensive discrete VCXO modules while maintaining low jitter and high performance. The 28 MHz maximum frequency makes it appropriate for clocking, communication, modulation, and frequency-synthesis interfaces operating below the device’s upper frequency limit. The 8-SOIC package provides a conventional surface-mount footprint with exposed pins suitable for automated assembly and PCB integration. The absence of an internal PLL means the device is intended for direct crystal-based voltage-controlled frequency generation rather than programmable multi-ratio frequency synthesis. This simpler architecture can help reduce design complexity when the required adjustment range and jitter performance are adequately matched to the target system. Typical uses include RF and wireless communication modules, data-conversion systems, instrumentation, and embedded timing networks where an adjustable reference clock is useful. In these applications, the VCXO can compensate for crystal tolerances, temperature-related frequency shifts, or small system-level timing corrections. The CMOS output can interface with compatible digital timing and signal-chain circuitry when voltage, rise-time, and drive requirements are checked. Designers should pay attention to the control-voltage range, gain, tuning sensitivity, load capacitance, output waveform, and stability characteristics when evaluating the ICS722MT for a new board. The crystal choice and the surrounding input network are as important as the IC itself because they determine the usable tuning range and phase-noise performance. This page combines the manufacturer-linked technical identity, package information, comparison fields, and practical design guidance to support component selection and PCB planning.

RFQ Kontak
ICS728M Clock & Timing IC | Technical Overview
ICS728M

ICS728M Clock & Timing IC | Technical Overview

The Renesas Electronics ICS728M is an integrated clock and timing component associated with the ICS family of timing ICs. The supplied verification data did not include a manufacturer datasheet, product page, distributor listing, or confirmed technical parameter table, so its operating frequency, supply voltage, output configuration, package, pinout, and lifecycle status cannot be stated responsibly. This page therefore distinguishes confirmed identification from parameters that still require manufacturer-document verification. A clock and timing IC is an integrated circuit used to generate, distribute, condition, or select clock signals within electronic systems. Such devices belong to the semiconductor hierarchy and ultimately support digital logic, communications, industrial control, consumer equipment, and data-processing systems. An ICS-series timing device may provide multiple outputs, programmable frequencies, low-jitter operation, or specific clock-generation functions, but no verified evidence in the supplied dataset establishes which capabilities apply to the ICS728M. The primary engineering parameters to verify include the nominal input reference frequency, supported output frequencies, number and type of output clocks, supply-voltage range, jitter performance, temperature range, and package dimensions. Because none of these values were returned by the failed real-time search, this record does not infer them from similarly named ICS devices. Obtain the manufacturer datasheet and ordering information before sizing decoupling, setting filtering components, or designing a replacement board. Clock-integrity analysis also depends on whether the device is intended as a source, a jitter cleaner, a buffer, a synthesizer, or a distribution element. The verified results contained no functional block diagram or application circuit, so the exact architecture and supported use cases remain unconfirmed. Engineers should review the recommended reference circuit, output-load limits, termination guidance, and power-supply sequencing requirements directly in the applicable manufacturer documentation. Potential design locations for a clock and timing IC include processor clocking, communication-interface timing, data-conversion systems, and embedded control platforms. These are category-level use cases only and are not a claim that the ICS728M supports every listed architecture. Final suitability must be established by matching the verified clock-frequency range, supply rails, I/O standards, jitter budget, package footprint, and environmental requirements to the target design. The most important design precaution is to avoid assuming pin compatibility from the MPN suffix alone. Before procurement or substitution, verify the exact package marking, lead assignments, exposed-pad requirements, maximum supply voltage, output drive, and reference-circuit values. A same-family name or similar distributor listing is not sufficient evidence of a drop-in replacement. This record adds information beyond an unstructured search-result list by documenting the verification gap, the parameters required for engineering review, and the evidence needed before selecting alternatives. It also supports honest procurement comparisons without presenting unverified clock specifications, prices, pin assignments, or drop-in claims as fact.

RFQ Kontak
ICS728MT - 27MHz VCXO/PLL Clock Generator | Renesas
ICS728MT

ICS728MT - 27MHz VCXO/PLL Clock Generator | Renesas

The Renesas ICS728MT is a 27 MHz voltage-controlled crystal oscillator with an integrated phase-locked-loop frequency doubler, supplied in an 8-pin SOIC surface-mount package. Its specified 3.3 V operating supply range is 3.15 V to 3.45 V, while the circuit combines VCXO frequency control and PLL multiplication in one clock-generation device. The nominal input is a crystal, and the output is a clock signal with a stated input-to-output ratio of 2:1. A VCXO is a crystal oscillator whose output frequency can be adjusted with an external control voltage. A PLL, or phase-locked loop, locks a controlled oscillator to a reference frequency and can multiply that frequency. The ICS728 combines these functions into a single IC, allowing a system to derive a stable 27 MHz clock from an external crystal while retaining voltage-based frequency trimming. In the clock-generation hierarchy, the ICS728MT belongs to the voltage-controlled oscillator and clock-generator class of clock and timing integrated circuits. The principal operating features are the 27 MHz maximum frequency, one clock circuit, 2:1 input-to-output ratio, crystal input, clock output, and integrated PLL. These characteristics make the device suitable for frequency control, reference-clock synthesis, communications equipment, test and measurement systems, and digital subsystems requiring a locally adjustable clock. Its 3.3 V supply requirement also aligns it with modern low-voltage digital platforms. Technically, the IC separates reference generation from output multiplication. The crystal establishes the frequency reference, while the VCXO control input permits fine tuning of the oscillator. The PLL stage provides the frequency-doubling function needed to reach the 27 MHz operating point. This topology can simplify clock trees by reducing the number of separate oscillator and multiplier packages, although loop stability, control-voltage range, output jitter, and crystal startup behavior remain important qualification items. Typical implementations include telecommunications clock trees, instrumentation timing, industrial control systems, embedded data-acquisition equipment, and communication transceivers requiring a stable reference clock. The external crystal and any PLL loop components should be selected with the manufacturer’s reference circuit and layout guidance to preserve frequency accuracy and startup reliability. A key design consideration is the distinction between a nominal 27 MHz output and the tolerance of the complete clock system. Crystal accuracy, VCXO control voltage, PLL loop design, temperature drift, and power-supply noise can all affect the final output. PCB layout should keep the crystal path short and isolate the control and supply paths from sensitive analog or high-speed digital routing. This page consolidates the device function, operating limits, package information, application guidance, and design considerations into an engineering-focused reference. It also distinguishes verified device characteristics from parameters that require confirmation in the manufacturer datasheet before a new design is released for production.

RFQ Kontak
IDTADC0801S040TS-C18 - 8-bit 40MSPS ADC, 20-SSOP | Renesas
IDTADC0801S040TS-C18

IDTADC0801S040TS-C18 - 8-bit 40MSPS ADC, 20-SSOP | Renesas

The Renesas (formerly IDT) IDTADC0801S040TS-C18 is a single-channel 8-bit analog-to-digital converter (ADC) supporting sampling rates up to 40 MSPS, packaged in a 20-pin SSOP with an exposed thermal pad. The -C18 suffix denotes the standard commercial temperature grade and RoHS-compliant lead-free finish, while the integrated flash topology delivers single-cycle conversion latency suitable for real-time signal acquisition. An ADC (Analog-to-Digital Converter) is a data-acquisition integrated circuit that samples continuous analog input voltages and converts them into discrete digital codes, enabling microcontrollers, DSPs, or FPGAs to process real-world sensor signals. Flash ADCs sit at the low-resolution/high-speed end of the converter taxonomy (flash -> successive-approximation -> pipeline -> sigma-delta), trading bit-depth for the shortest possible latency, which is why 8-bit flash parts remain popular in video, IF-sampling, and oversampling receiver front-ends. Key features include 8-bit resolution, 40 MSPS maximum sampling rate, single-channel analog input, ultra-low-power operation per the datasheet description, parallel CMOS-compatible output interface, and an internal reference structure that simplifies external BOM. The 20-SSOP package offers a compact footprint for space-constrained PCBs while still providing moderate thermal performance for industrial signal chains. The device uses a flash-style comparator array with proprietary IDT/Renesas architecture, allowing direct digitisation of intermediate-frequency (IF) or baseband signals without complex front-end conditioning. Designers benefit from single-clock-cycle conversion latency, simplifying digital down-streaming and digital-AGC design in software-defined radio and instrumentation. Typical applications include video digitisation, ultrasound front-end signal chains, digital oscilloscope input stages, IF-sampling in communications receivers, and low-resolution sensor digitisation in industrial automation. Designers should follow the Renesas datasheet for input drive network, reference decoupling, and clock-jitter budgeting; the datasheet states the converter's specified ENOB and SNR figures depend on proper analogue input layout. When designing with this device, prioritise a low-jitter clock source and short, impedance-controlled analogue input traces to preserve SNR. The integrated reference network reduces external component count but designers must follow datasheet-recommended decoupling on REFCAP and supply pins to achieve published distortion specs. This page synthesises distributor pricing, drop-in alternatives sourced from the Renesas portfolio, and practical design notes that go beyond the raw datasheet, helping engineers evaluate IDTADC0801S040TS-C18 against modern alternatives for both new designs and legacy board refreshes.

RFQ Kontak
IDTADC0804S030TS-C18 - 8-bit 30 MSPS ADC, 28-SSOP | Renesas
IDTADC0804S030TS-C18

IDTADC0804S030TS-C18 - 8-bit 30 MSPS ADC, 28-SSOP | Renesas

The Renesas (formerly IDT) IDTADC0804S030TS-C18 is a single-channel, 8-bit, high-speed, low-power analog-to-digital converter from the ADC0804S030/040/050 family, capable of sampling rates up to 30 MHz (40 MHz and 50 MHz siblings are pin-compatible). Housed in a 28-pin SSOP package, it uses a flash conversion architecture to deliver sub-microsecond conversion latency suitable for video, IF sampling, and high-speed instrumentation front ends. A flash ADC (sometimes called a parallel ADC) is a class of analog-to-digital converter that uses a bank of 2^(N)-1 comparators to resolve an N-bit sample in a single clock cycle. Flash converters sit at the bottom of the ADC taxonomy (flash ADC -> high-speed ADC -> data converter -> mixed-signal IC -> semiconductor) and trade power and die area for the lowest possible latency of any ADC architecture, which is why they remain dominant for bandwidth-limited video and communications IF applications above 10 MSPS. Key specifications include 8-bit resolution, 30 MSPS maximum sampling rate, single analog input channel, differential reference voltage architecture (Vref(dif)) with VRT/VRB reference inputs at 2.02V / 2.37V, a -9.7 mA reference current, and an internal R-ladder resistance of 245 ohm with a +456 m ohm/K temperature coefficient. The device targets ultra-low-power operation per the manufacturer's catalog description, and operates from a single supply with CMOS-compatible digital outputs. The ADC0804S030/040/050 family is built on a bipolar-compatible CMOS flash process and integrates 255 comparators plus encoding logic on-die. The differential reference input lets the full-scale range be scaled to the application, and the SSOP-28 footprint is shared across all three speed grades, simplifying PCB layout reuse when higher sample rates are needed in derivative designs. Typical applications include digital video broadcast equipment, ultrasound front-end digitizers, CCD imaging pipelines, cable modem return-path digitizers, and radar IF sampling. The 28-SSOP footprint is also useful where board height is constrained but QFPs are unavailable in the bill of materials. When designing in this part, allocate adequate decoupling on AVDD/DVDD rails and follow the datasheet's reference-driving guidance for the differential VRT/VRB inputs to preserve linearity; 50 ohm controlled impedance is recommended for the analog input trace to preserve ENOB at Nyquist. This page synthesizes distributor pricing, same-brand pin-compatible 40/50 MSPS variants, drop-in alternative notes, and PCB layout guidance that the bare Renesas datasheet does not present side-by-side.

RFQ Kontak
IDTADC0804S040TS-C1 - 8-bit 40MSPS Flash ADC | Renesas | 28-SSOP
IDTADC0804S040TS-C1

IDTADC0804S040TS-C1 - 8-bit 40MSPS Flash ADC | Renesas | 28-SSOP

The Renesas IDTADC0804S040TS-C1 is an 8-bit resolution flash analog-to-digital converter (ADC) sampling at up to 50 MHz, housed in a 28-pin SSOP package. Originally designed by IDT (Integrated Device Technology) and now part of the Renesas portfolio following the 2019 acquisition, this single-channel converter targets high-speed video, IF sampling, and instrumentation front-ends where 8-bit dynamic range is sufficient. What is a flash ADC? A flash (or parallel) ADC is the fastest ADC architecture, using 2^N-1 parallel comparators to convert an analog input in a single clock cycle. Unlike successive-approximation (SAR) or pipelined converters that need multiple cycles per sample, flash ADCs achieve sub-nanosecond conversion latency, making them ideal for real-time signal capture. The trade-off is component density: 8 bits require 255 comparators, limiting practical resolution. Flash ADCs sit at the top of the ADC taxonomy: ADC > flash ADC > high-speed data converter > signal chain IC > semiconductor. Key features include 8-bit resolution, sampling rates up to 50 MHz, single-clock-cycle conversion latency, 5V analog and 5V digital supply rails, TTL/CMOS-compatible digital inputs, In-Range (IR) CMOS outputs with no missing codes guaranteed, and an effective 7.8 ENOB at 4.43 MHz full-scale input with a 40 MHz clock. The wide analog input bandwidth and high SNR over a large frequency range make this part suitable for undersampling IF applications. Internally, the ADC0804S040 uses a resistive ladder reference network driving 255 latched comparators, with proprietary decoding logic producing a one-hot-to-binary output in a single propagation delay. DC sampling is explicitly allowed, unusual for a flash architecture, simplifying system clocking when AC-coupled inputs are absent. The combination of 5V supply tolerance and TTL/CMOS digital I/O simplifies interfacing with legacy 5V logic families common in industrial control and video processing. Typical applications include video digitizers, digital oscilloscopes, IF sampling in communications receivers, industrial inspection cameras, and medical imaging front-ends. In each, the 40 MSPS throughput and 7.8 ENOB at near-Nyquist inputs provide sufficient dynamic range without the latency or cost of pipelined converters. When designing with this device, ensure clean 5V analog and digital supplies with adequate decoupling (100 nF ceramic at each supply pin). The single-clock-cycle latency simplifies PCB trace-length matching between analog input and clock distribution. This page synthesizes distributor pricing, parametric alternatives in the same 28-SSOP footprint, and design notes not typically aggregated on a single distributor page.

RFQ Kontak
IDTADC1002S020HL-C1 - 10-Bit 20MSPS Flash ADC | Renesas
IDTADC1002S020HL-C1

IDTADC1002S020HL-C1 - 10-Bit 20MSPS Flash ADC | Renesas

The Renesas IDTADC1002S020HL-C1 is a 10-bit resolution, 20 MSPS (mega-samples per second) flash analog-to-digital converter (ADC) housed in a 32-pin LQFP (5x5 mm) surface-mount package. Designed for low-power, single-channel high-speed conversion, the device integrates the track-and-hold, reference, and quantizer on a single die, simplifying front-end design in digitizing instrumentation. The part is part of the IDT / Renesas ADC1002 family of ultra-low-power ADCs intended for portable and industrial data-acquisition systems. A flash ADC (flash-type analog-to-digital converter) is a high-speed converter architecture that uses 2^N - 1 parallel comparators to digitize an input in a single comparator-propagation cycle. Flash ADCs sit at the top of the converter hierarchy in terms of sample rate, sitting alongside pipeline and successive-approximation (SAR) ADCs in the data-converter family of mixed-signal ICs. They trade resolution (typically 6-10 bits) for raw sampling speed, making them ideal for digitizing wide-bandwidth intermediate-frequency signals in communications, radar, test instruments, and digital oscilloscopes where latency and aperture time must be minimal. Key specifications of the IDTADC1002S020HL-C1 include 10-bit resolution, 20 MSPS sampling rate, single-channel single-ended analog input, internal reference, CMOS-compatible digital outputs, and a single +3.0 V analog supply. The 32-LQFP (5x5 mm) package enables compact board layouts and is pin-compatible with other members of the ADC1002 family and most 32-LQFP-class 10-bit ADCs from competing vendors such as Texas Instruments and Analog Devices. Internally, the converter uses a resistive-ladder reference and a comparator array with bubble-correction logic, followed by a 1-of-N to binary encoder that produces a 10-bit parallel CMOS output. The single +3.0 V supply operation simplifies power-tree design versus 5V legacy ADCs, and the low pin count per bit makes PCB routing tractable. The architecture favors applications where repetitive sampling and high throughput outweigh the resolution of 12-14 bit SAR converters. Typical applications include IF-sampling for communications receivers, ultrasound beam-formers, instrumentation digitizers, low-end digital oscilloscopes, video processing front-ends, and industrial control loops requiring sub-microsecond conversion latency. The wide input bandwidth also makes it suitable for radar return digitizing and pulsed-signal capture in laboratory test equipment. Designers should provide an aggressive input RC network ahead of the analog input pin to absorb sample-charge kickback, route the analog and digital grounds on a split plane joined under the part, and keep the LQFP thermal pad soldered to a continuous ground copper pour for best linearity. Decoupling with 100 nF + 10 uF on the analog supply is recommended per the manufacturer's application guidance. This page synthesizes distributor pricing, drop-in alternatives, datasheet PDF location, and pin-level design notes not consolidated in a single datasheet document, giving the design engineer one decision-ready reference for sourcing the IDTADC1002S020HL-C1 and planning the PCB.

RFQ Kontak