Mga Produkto (44,000+)

ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas
ISL8485ECP

ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas

The Renesas Electronics ISL8485ECP is a single half-duplex RS-485 and RS-422 line transceiver IC operating from a 5 V supply and supplied in an 8-pin PDIP package. It combines one driver and one receiver in one device, supports ESD protection to ±15 kV, and includes driver short-circuit current limiting and on-chip thermal shutdown for improved robustness during bus contention. A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers. The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring. The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration. Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture. PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process. This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.

RFQ Kontak
ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IB

ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas

Renesas Electronics ISL8485IB is a single half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and a 5 V supply in an 8-pin SOIC package. The ISL8485IB uses BiCMOS technology and is specified for 4.5 V to 5.5 V power supplies, including the 10% supply tolerance identified on the Renesas product page. Its industrial temperature range extends from -40°C to +85°C. An RS-485/RS-422 transceiver is a differential communications interface IC that converts logic-level transmit and receive signals into balanced, noise-immune bus signals. The ISL8485 family supports both RS-485 half-duplex operation and RS-422 balanced operation. The ISL8485 configuration multiplexes its driver output and receiver input onto the same pair of bus terminals, allowing a compact eight-pin implementation. The principal features include a 5 Mbps maximum data rate, low-power BiCMOS construction, operation from a nominal 5 V rail, and a single-unit-load RS-485 bus interface. Half-duplex operation requires the design to control the driver-enable and receiver-enable functions so that the transmitter is disabled when the bus is not being driven. These characteristics make the device appropriate for industrial data links, instrumentation, factory equipment, and point-to-point or multidrop balanced communication. The ISL8485IB is one of three related devices: the ISL8485 provides half-duplex multiplexing, while the ISL8490 and ISL8491 provide separate receive and transmit paths for full-duplex applications. The Renesas ISL8485, ISL8490, and ISL8491 datasheet identifies these architectural differences explicitly. Because bus topology and enable logic affect protocol behavior, an existing PCB should be checked for pin functions before selecting a related family member. Typical installations include RS-485 industrial sensor networks, RS-422 controller-to-peripheral links, building-control equipment, and data-acquisition systems. The 5 Mbps capability supports faster communication than legacy low-speed RS-485 links, while the differential interface helps reject common-mode noise when the transceiver is used with correctly terminated cabling. Designers should verify the eight-pin pinout, supply decoupling, driver-enable sequencing, bus termination, and protection requirements against the manufacturer datasheet. Differential routing should use a controlled-impedance layout where practical, and the unused bus terminals must be handled according to the applicable RS-485 or RS-422 configuration. This page consolidates the verified Renesas and distributor information for the ISL8485IB, documents pin-compatible alternatives with their differences, and provides practical interface-design guidance that is not available from a distributor listing alone.

RFQ Kontak
ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IBZ

ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8485IBZ is a single half-duplex RS-485/RS-422 transceiver operating from a 4.5 V to 5.5 V supply, with a maximum data rate of 5 Mbps, in an 8-pin SOIC package. The device combines one driver and one receiver and presents one unit load to an RS-485 bus. An RS-485/RS-422 transceiver is a balanced data-communications interface that converts logic-level signals into differential bus signals and receives differential signals from the bus. These interface ICs belong to the transceiver hierarchy within interface integrated circuits and support robust point-to-point or multipoint communication over longer distances than conventional single-ended logic links. The ISL8485 family is specified for 10% supply tolerance, allowing operation across the 4.5 V to 5.5 V range. Its BiCMOS architecture supports data rates up to 5 Mbps, making the ISL8485IBZ useful for industrial control links, factory automation equipment, instrumentation, and other balanced-communication systems. The balanced interface also improves noise immunity in environments containing switching equipment and industrial motors. The ISL8485 is a half-duplex device, so the driver and receiver share the bus connection rather than operating simultaneously. System design must account for this shared use of the interface and provide the required direction-control function. The 8-SOIC outline supports compact, surface-mount PCB construction, although exact pin names and exposed-pad details should be confirmed against the manufacturer pin-description table before routing a new design. Typical uses include RS-485 links between controllers and sensors, communication between industrial modules, and RS-422-compatible point-to-point interconnects. The 5 Mbps maximum rate supports relatively fast control and data traffic, while the differential signaling method reduces susceptibility to common-mode noise. Cable length, topology, termination, grounding, and data rate must be considered together because faster operation generally imposes more restrictive channel requirements. For PCB implementation, place the transceiver close to the connector and route the balanced pair as a tightly coupled differential pair with continuous ground referencing. Use the termination and protection strategy appropriate for the installation, and keep switching-node currents away from the receiver path. This page also organizes lifecycle, sourcing, replacement, and application guidance around the manufacturer’s ISL8485 family information.

RFQ Kontak
ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IP

ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8485IP is a 5V, low-power, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5Mbps and supplied in an 8-pin DIP package. It provides one balanced transceiver interface for bidirectional multipoint data communication, places one unit load on an RS-485 bus, and operates from a supply range of 4.5V to 5.5V. The device is intended for industrial communication links requiring either high-speed operation or controlled slew rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential signals for balanced wired communication and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced links, while RS-485 permits multipoint buses and driver-enable control. The ISL8485IP belongs to the transceiver hierarchy within interface ICs and combines transmitter, receiver, bus-enable control, and protection functions in one package. Key features include a 5Mbps maximum data rate, 4.5V to 5.5V supply tolerance, one-unit-load bus loading, and support for both RS-485 and RS-422 signaling. The 8-pin DIP package is suitable for conventional through-hole assembly, prototyping, repair, and industrial control equipment. Its half-duplex arrangement allows the same differential pair to transmit and receive, although external direction-control logic is normally required. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation with high data-rate capability. According to the Renesas ISL8485 family information, the ISL8485, ISL8490, and ISL8491 devices are 5V-powered single transceivers that meet RS-485 and RS-422 standards. The family supports supply voltages with 10% tolerance and presents one unit load to the RS-485 bus, helping control loading when multiple nodes share a communication line. Typical applications include industrial factory automation, programmable-logic-controller communication, building-control networks, instrumentation links, and embedded serial-interface equipment. In these systems, the transceiver serves as the physical-layer interface between a controller UART or logic port and a balanced RS-485 or RS-422 cable. Its 5Mbps capability supports high-speed equipment links, while slew-rate-controlled variants in the broader family can be useful where lower EMI is the priority. PCB design should preserve the differential signal path and provide controlled termination and biasing appropriate to the selected RS-485 or RS-422 topology. Keep the transceiver close to the connector, route the differential pair as a coupled pair, and place termination components where they can be configured for the intended network. The maximum 5.5V supply is especially important in industrial systems because transients and supply tolerances must remain within the device rating. This product page combines verified distributor identification, package and interface details, family-level electrical characteristics, alternative sourcing information, and application-specific engineering guidance. It also distinguishes explicitly verified facts from parameters that require confirmation from the manufacturer datasheet before schematic release or production qualification.

RFQ Kontak
ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IPZ

ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

Renesas ISL8485IPZ is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin PDIP package. It operates from a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and combines one transmitter and one receiver in a single integrated circuit. The BiCMOS implementation supports balanced industrial-communication links where a compact, single-part interface is preferred. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as logic-level outputs. RS-422 provides a point-to-point balanced communication format, while RS-485 supports multipoint bus arrangements. The ISL8485IPZ belongs to the interface-IC hierarchy within integrated circuits and is used where electrical isolation, protocol conversion, or galvanic distance is handled elsewhere in the system. The principal operating features are a 4.5 V to 5.5 V supply range, operation to 5 Mbps, half-duplex communication, and one-unit-load RS-485 bus loading. These characteristics suit equipment that exchanges data over relatively short, high-speed balanced interconnects. The integrated transmitter and receiver reduce board area compared with separate driver and receiver circuits, while the PDIP package supports conventional through-hole assembly and prototyping. The BiCMOS architecture combines bipolar and CMOS circuit techniques, allowing the device to provide high-speed differential signaling while maintaining low-power interface operation. Half-duplex operation means the transmitter and receiver share the same differential pair, so the design must correctly manage driver-enable and receiver-enable controls to prevent unwanted bus contention. The one-unit-load rating permits multiple compatible transceivers to share an RS-485 network, subject to the total-load and topology limits of the completed bus. Typical uses include industrial control equipment, factory automation links, data-acquisition equipment, instrumentation, and communications modules that connect a host controller to an RS-485 or RS-422 peripheral. The 5 Mbps capability is useful for short links carrying frequent control or diagnostic messages, although cable length, topology, termination, grounding, and transceiver delay determine the practical communication distance. Designers should place the transceiver near the connector and cable entry point, provide the required supply and bypass capacitance, and follow the manufacturer datasheet for driver-enable and receiver-enable logic. Differential pairs should be routed with consistent geometry and controlled impedance. A termination resistor is normally placed at each end of an RS-422 link; RS-485 termination practices depend on the bus topology and its signal reflections. This page combines the exact Renesas product characteristics, package information, pricing evidence, interface-family relationships, comparison parameters, and practical implementation guidance. It also distinguishes verified drop-in alternatives from near-equivalent devices that use a different package and therefore require PCB redesign rather than simple component substitution.

RFQ Kontak
ISL8487EIB - 5V RS-485/RS-422 Transceiver | Renesas
ISL8487EIB

ISL8487EIB - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8487EIB is a 5 V, single RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. It supports balanced data communications, provides ±15 kV ESD protection on driver outputs and receiver inputs, and offers a 1/8-unit-load receiver for demanding multidrop and multipoint networks. The family operates from a single 5 V supply and is designed for low-power industrial interfaces. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential, balanced bus signals and receives differential bus signals back into CMOS-compatible logic. The differential architecture improves common-mode noise rejection and supports communication over longer cables than single-ended interfaces. The ISL8487E belongs to the RS-485 transceiver hierarchy, within interface ICs and broader data-communication semiconductors. Key characteristics include ±15 kV ESD protection, fractional 1/8-unit loading, 5 V operation, and a maximum quiescent current of 145 µA for the ISL8487E family. The fractional loading permits as many as 256 devices on a bus under ideal conditions, subject to the network configuration and system-level constraints. Both high-speed and slew-rate-limited versions appear in the ISL8487E family, so the exact drive and data-rate limits should be confirmed from the ISL8487E datasheet before selecting the required speed grade. The BiCMOS implementation combines low power with balanced-line drive capability. The receiver can monitor bus activity independently of the driver, while the driver and receiver enables support controlled connection to a multidrop network. The ±15 kV protection is particularly useful in industrial environments where cables may connect to external equipment and exposed connectors. Typical applications include industrial process automation, remote meter reading, building controls, factory equipment links, multidrop instrumentation buses, and point-to-point RS-422 links. The low 1/8-unit load is valuable when many nodes share one bus, while the small SOIC-8 package simplifies PCB routing in compact control equipment. When laying out the circuit, route the differential A and B traces as a closely coupled pair, provide the transceiver-side decoupling recommended by the manufacturer datasheet, and use chassis-ground protection methods at exposed connectors. Termination remains a network-level decision: terminate the far ends of the bus rather than every node, and confirm whether the selected family member uses slew-rate-limited or high-speed drive. This page combines the manufacturer family specifications, package and interface details, comparison guidance, and practical PCB considerations to accelerate transceiver selection for balanced industrial communication links.

RFQ Kontak
ISL8487IB - 250 kbps RS-485/422 Transceiver | Renesas
ISL8487IB

ISL8487IB - 250 kbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8487IB is a 5 V, single-channel half-duplex RS-485/RS-422 interface transceiver with a 250 kbps data rate, 1/4 unit load, and an 8-pin SOIC package. It combines one driver and one receiver in a fractional-unit-load design intended for balanced industrial communication links where the number of connected nodes is important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into digital logic. Positioned within the hierarchy of transceiver, communication interface, interface IC, and semiconductor categories, the ISL8487IB supports RS-485 and RS-422 networks while presenting a lower bus loading than a one-unit-load device. The ISL8487IB operates from a 5 V supply and presents a 1/4 unit load, allowing up to 128 transceivers on a compliant RS-485 bus. Its maximum data rate is 250 kbps, and the listed receiver hysteresis is 70 mV. The 8-SOIC surface-mount package measures approximately 0.154 inches, or 3.90 mm, in width and supports conventional board-assembly and inspection processes. Because the device is a half-duplex transceiver, the receiver and driver share the bus path and direction is controlled by the DE and RE inputs. This architecture suits point-to-point links as well as multidrop buses in which multiple nodes may communicate under a token-passing or polled protocol. The fractional unit load reduces input impedance loading compared with a standard one-unit-load transceiver, improving scalability without requiring an alternative physical bus topology. Typical applications include industrial process monitoring, factory automation, remote meter reading, building controls, instrumentation, and general-purpose RS-485 or RS-422 links. The 250 kbps rate is suitable for supervisory communications and moderate-speed data transfer, while the 1/4 unit load is especially useful when several nodes must share the same twisted-pair bus. Because the transceiver is not galvanically isolated, applications with large ground-potential differences may require an external isolation strategy. Designers should verify termination, biasing, differential routing, and protection against the electrical environment of the cable. The differential pair should be routed as a controlled-impedance pair where practical, and the transceiver should be placed close to the connector to minimize unprotected trace exposure. Supply decoupling and grounding must follow the manufacturer datasheet recommendations. This page combines verified distributor specifications, lifecycle information, source-linked pricing, package details, application guidance, and defensible same-footprint alternatives. It also distinguishes confirmed data from parameters not present in the supplied source material, helping engineers evaluate the obsolete ISL8487IB without assuming unverified electrical characteristics.

RFQ Kontak
ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
ISL8487IB-T

ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas

Renesas ISL8487IB-T is a half-duplex, single-transceiver interface IC for RS-485 and RS-422 data links, operating from a 5 V supply and offering one-quarter unit-load drive capability in an 8-pin SOIC package. The ISL8487IB-T combines a low-power RS-485/RS-422 transceiver with ESD-protected communication pins, making it suitable for industrial control, instrumentation, and point-to-point or multidrop serial networks where low power and compact packaging are important. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs. The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections. The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation. Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements. PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering. This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.

RFQ Kontak
ISL8487IBZ - 5V RS-485/RS-422 Transceiver | Renesas
ISL8487IBZ

ISL8487IBZ - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8487IBZ is a 5 V, single-channel RS-485 and RS-422 transceiver in an 8-pin SOIC package. It combines one driver and one receiver, supports a fractional 1/8 unit load, and provides the differential interface required by balanced industrial-communication links. The device is identified as an ESD-protected 8-SOIC transceiver, making it suitable for compact RS-485 equipment, multidrop field buses, industrial control systems, and point-to-point RS-422 links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential voltage waveforms for reliable communication over balanced copper cables. The transmitter drives a differential output, while the receiver converts the differential input into a logic-level signal. By placing a common-mode voltage range and differential signaling between two conductors, this interface class supports improved noise immunity compared with single-ended communication. The ISL8487 family therefore sits between a host controller and a physical network such as Modbus RTU, PROFIBUS-related equipment, or proprietary industrial buses. The ISL8487IBZ operates from a 5 V supply and is designed for low-power, high-speed or slew-rate-limited communication. Its fractional 1/8 unit-load characteristic allows more receiving nodes on a multidrop bus than a conventional one-unit-load transceiver. Because the package contains one transmitter and one receiver, it can support half-duplex communication when the driver and receiver controls are managed by the host. The device also includes ESD protection, an important feature for transceiver devices connected to external cables and field-accessible equipment. The family is described as BiCMOS and is designed to meet RS-485 and RS-422 balanced-communication requirements. Its low-power operation suits distributed equipment where every milliampere can affect system thermal design. In half-duplex networks, the receiver may remain active while the driver is disabled, allowing the attached controller to detect responses or bus contention. Designers should still control the enable and disable timing to prevent the driver from fighting an external driver during bus turnaround. Typical uses include industrial sensor gateways, PLC communication ports, building-control terminals, instrumentation, data-acquisition equipment, and factory automation nodes. The 8-SOIC package also supports compact peripheral boards where a larger multi-channel transceiver would be unnecessary. In a typical multidrop network, the ISL8487IBZ connects a UART or embedded controller to the balanced bus, while termination and biasing components are placed only where required by the network topology. The main design consideration is cable-side protection. Although the device includes ESD protection, the maximum bus voltage, common-mode range, ground-reference limits, connector placement, and external surge-protection requirements must be checked against the application environment. Keep the balanced pair tightly coupled, connect the transceiver ground reference appropriately, and verify termination and fail-safe behavior for the selected operating mode. The 5 V supply should be decoupled close to the device, and unused control inputs must not float. This page combines the component identity, RS-485/RS-422 interface characteristics, package information, replacement guidance, comparison details, and practical PCB-design considerations into a focused engineering reference. It also identifies the available same-package alternatives and distinguishes the verified role of each candidate for drop-in replacement decisions.

RFQ Kontak
ISL8487IP - 5V Half-Duplex RS-485/RS-422 Transceiver | Renesas
ISL8487IP

ISL8487IP - 5V Half-Duplex RS-485/RS-422 Transceiver | Renesas

Renesas ISL8487IP is a 5 V, half-duplex RS-485/RS-422 interface transceiver with one transmitter and one receiver in an 8-pin PDIP package. It supports a 1/8-unit-load receiver characteristic, low-power operation, driver-enable and receiver-enable control, and a low-power shutdown function. These characteristics make it suitable for bidirectional serial-data links that require both RS-485 and RS-422-compatible signaling without a separate supply rail for the interface. An RS-485/RS-422 transceiver is a differential interface IC that converts logic-level data into balanced differential signals and converts incoming differential signals back into receiver-compatible logic. Within the broader hierarchy, it is a transceiver interface IC, a wired-communication interface, and part of the broader semiconductor and industrial-control ecosystem. Its half-duplex architecture allows a pair of devices to share the same differential pair, although only one transmitter should drive the bus at a time. The ISL8487IP provides a 1/8-unit-load receiver, allowing multiple nodes to share a bus more effectively than a one-unit-load receiver. Its 5 V supply, low-power shutdown, separate transmitter and receiver enables, and selectable high-speed or slew-rate-limited operation give the designer several ways to balance throughput, EMI control, and power consumption. The transmitter-enable and receiver-enable inputs also support orderly bus-direction control in half-duplex equipment. According to the manufacturer datasheet, the device uses fractional-unit-load BiCMOS transceiver technology intended for balanced RS-485 and RS-422 networks. The slew-rate-limit option reduces the rate of change on driver output edges, which can help control high-frequency ringing and electromagnetic emissions. Conversely, the high-speed mode is intended for links where maximum communication rate is more important than edge-rate control. Exact propagation-delay, data-rate, differential-output, and current-limit values were not present in the supplied web data. Typical uses include industrial equipment links, building-control interfaces, instrumentation buses, data-acquisition systems, and host-controller communication ports. In a half-duplex system, the transceiver can connect a controller to a multidrop field bus while logic-controlled enables determine whether the node transmits or receives. The low-power shutdown function is useful when a connected module must reduce current consumption while preserving a stable local bus connection. Designers should verify the exact recommended termination, biasing, common-mode range, and decoupling requirements in the manufacturer datasheet before release. Differential pairs should be routed with continuous references and matched spacing, while a slew-rate-limited mode may be preferable in cables or cabinets exposed to significant EMI. The 8-pin PDIP package also requires adequate spacing around the leads for soldering and inspection.

RFQ Kontak
ISL8488EIB - ESD-Protected RS-485/RS-422 | Renesas
ISL8488EIB

ISL8488EIB - ESD-Protected RS-485/RS-422 | Renesas

The Renesas Electronics ISL8488EIB is a single-channel, half-duplex RS-485/RS-422 interface transceiver built with BiCMOS technology and operated from a single 5 V supply. It accepts a 4.5 V to 5.5 V supply range and provides one driver and one receiver in an 8-pin SOIC package. Driver outputs and receiver inputs are protected against ESD strikes up to ±15 kV without latch-up. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and board-level interconnects. The ISL8488EIB belongs to the broader hierarchy of transceiver IC, interface IC, communication IC, and semiconductor. Its differential signaling supports noise rejection, while its integrated ESD protection helps preserve interface reliability in industrial and commercial systems where exposed connector pins may encounter electrostatic discharge. The device provides full RS-422 and RS-485 operation from a single 5 V rail. Its 10% supply tolerance allows operation across the 4.5 V to 5.5 V range rather than requiring a tightly regulated 5 V source. The integrated protection applies to both driver outputs and receiver inputs, and the BiCMOS process combines low-power CMOS characteristics with bipolar drive capability. These features make the device suitable for robust point-to-point and multidrop balanced communication links. As a single transceiver, the ISL8488EIB is appropriate when a system requires one differential bus driver and one differential receiver rather than a multi-channel interface. The SOIC-8 package supports conventional surface-mount assembly and occupies a footprint compatible with established RS-485 interface layouts. Because a transceiver combines transmit and receive functions, system design must include correct driver enable control, bus termination, fail-safe biasing, grounding, and protection arrangements appropriate to the cable environment. Typical uses include industrial serial links, building-control equipment, factory automation, instrumentation, data acquisition, and embedded communications between circuit boards. The device can also serve in RS-422 links where a dedicated balanced driver and receiver are required. Its principal design considerations are correct logic-level interfacing, controlled bus-idle states, proper termination at the physical ends of the network, and protection of long exposed cables. For reliable operation, decouple the 5 V supply close to the device and route the balanced differential pair as a tightly coupled pair. Place termination resistors only at the physical ends of the bus, and use the receiver-enable and driver-enable controls to prevent multiple transmitters from driving the same network simultaneously. Confirm the final termination, biasing, and cable-length configuration against the communication standard used by the system. This page combines the manufacturer interface description, package information, protection characteristics, verified replacement references, and practical RS-485/RS-422 design guidance. It also distinguishes direct drop-in replacements from packaging-only variants, helping engineers evaluate PCB reuse, electrical compatibility, and sourcing requirements before modifying a qualified design.

RFQ Kontak
ISL8488IB - 250kbps Full-Duplex RS-485/422 | Renesas
ISL8488IB

ISL8488IB - 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8488IB is a 5V, full-duplex RS-485 and RS-422 transceiver capable of operation at 250kbps in an 8-pin SOIC package. The integrated interface IC combines one transmitter and one receiver for bidirectional point-to-point or multipoint serial links, while its slew-rate-limited driver helps reduce electromagnetic interference and ringing on inadequately terminated lines. An RS-485 transceiver is a differential communications interface IC used to connect a controller, programmable logic controller, sensor, or industrial endpoint to a balanced serial bus. RS-485 is a physical-layer standard suited to noisy industrial environments and longer cable runs, while RS-422 provides compatible differential signaling for point-to-point links. The ISL8488IB occupies the interface-IC hierarchy alongside RS-232 transceivers, isolated transceivers, and CAN controllers, but it operates with differential RS-485/RS-422 signaling rather than single-ended RS-232. The verified device data identifies a 5V supply, a 250kbps maximum signaling rate, full-duplex operation, slew-rate-limited drive, low-power operation, and the absence of separate receiver-enable and transmitter-enable controls. These features make the device appropriate for industrial and commercial systems where a compact, always-enabled full-duplex interface is preferred. The 8-SOIC format also supports conventional surface-mount PCB assembly and broad availability through distributors. The full-duplex arrangement separates the differential driver and receiver paths, allowing simultaneous transmission and reception. The slew-rate-limited driver is particularly useful where long cables, branch stubs, imperfect terminations, or reflected signals could otherwise produce unwanted EMI or excessive edge ringing. The supplied search evidence does not provide a verified common-mode range, receiver sensitivity, fail-safe behavior, bus loading, or propagation-delay distribution, so those values should be confirmed from the complete manufacturer datasheet before release. Typical uses include industrial controller links, factory automation equipment, building-control systems, instrumentation, telecom equipment, and embedded serial links where RS-485 or RS-422 is already selected. Because the part has no separate RX/TX enable inputs, the attached controller must handle bus-direction control elsewhere or the transceiver must remain in its continuously enabled interface configuration. The 250kbps data rate also places the device below the throughput normally associated with modern high-speed CAN or differential Ethernet interfaces. For a new PCB, preserve the manufacturer-recommended bypass capacitance, connect the differential pair as a controlled impedance or tightly matched pair, and provide termination only where the cable topology requires it. Avoid placing long unprotected stubs on the bus. Designers should also verify ground potential differences between connected systems because RS-485 relies on the common-mode voltage remaining within the device's supported operating range. This product record combines verified distributor listings, the manufacturer-family datasheet, available cross-reference evidence, packaging details, interface-use guidance, and a conservative same-footprint replacement assessment. It also distinguishes confirmed specifications from unavailable parameters so procurement and engineering teams can identify which values still require confirmation from the full datasheet.

RFQ Kontak
ISL8488IB-T - 250kbps Full-Duplex RS-485/422 | Renesas
ISL8488IB-T

ISL8488IB-T - 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8488IB-T is a single RS-485/RS-422 transceiver operating from a 5 V supply, with one transmitter and one receiver in an 8-SOIC package. The device supports data rates up to 250 kbps and provides full-duplex balanced communication without separate receiver-enable or transmitter-enable controls. Its low-power BiCMOS design is intended for industrial and commercial equipment where low-power differential interfaces, compact PCB area, and controlled transition behavior are important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals and reconstructs digital data from a differential receiver input. This device supports both RS-485 and RS-422 applications, covering point-to-multipoint bus communications and point-to-point links. Within the interface hierarchy, it belongs to the RS-485 transceiver category, uses differential signaling, and operates as a physical-layer communications component. The principal operating characteristics are a 5 V supply, a 250 kbps maximum signaling rate, full-duplex operation, and one integrated transceiver in an 8-SOIC package. The Intersil datasheet describes the ISL8488 family as a low-power, high-speed or slew-rate-limited RS-485/RS-422 device. Its balanced interface is suited to industrial networking, instrumentation, and control links where cable-length and ground-offset considerations make differential signaling preferable to single-ended logic. The BiCMOS architecture combines bipolar and CMOS process characteristics, supporting low-power operation while providing the drive and receive performance required by balanced communication links. The device accepts a 10% supply-tolerance range of 4.5 V to 5.5 V. Because the ISL8488IB-T has no receiver-enable or transmitter-enable pins, its operating state is managed entirely through the bus and data-path behavior rather than local logic-control inputs. Typical uses include industrial RS-485 controllers, factory automation equipment, building-control interfaces, instrumentation, and point-to-point RS-422 links. In these systems, the transceiver provides the physical-layer connection between a host UART or communications controller and a balanced cable. The 250 kbps ceiling makes it appropriate for moderate-speed control and monitoring traffic rather than high-speed video or storage networks. Layout should preserve the integrity of the differential pair and provide a controlled return path. Keep the two bus conductors closely coupled, route them away from high-current switching paths, and use the application guidance in the Intersil datasheet for termination and protection. Confirm the selected connector, cable, and grounding strategy satisfy the required RS-485 or RS-422 system configuration. This page consolidates the device identity, operating limits, package details, family alternatives, and implementation guidance into an engineering-focused resource. It also distinguishes verified operating facts from parameters that require confirmation against the manufacturer datasheet before production release.

RFQ Kontak
ISL8488IBZ - 5V Full-Duplex RS-485/RS-422 Transceiver | Renesas
ISL8488IBZ

ISL8488IBZ - 5V Full-Duplex RS-485/RS-422 Transceiver | Renesas

Renesas ISL8488IBZ is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It supports a 4.5V to 5.5V supply range, combines one driver and one receiver in each package, and is identified by the source material as an ESD-protected BiCMOS communications device. The ISL8488IBZ family is specified for both RS-485 and RS-422 balanced communication standards, making it suitable for industrial equipment, data acquisition systems, and point-to-point serial links. A transceiver such as the ISL8488IBZ belongs to the interface-IC hierarchy: transceiver → driver/receiver → differential data interface → semiconductor. RS-485 supports balanced, multipoint buses that can tolerate common-mode noise better than single-ended logic links, while RS-422 provides a balanced point-to-point interface. The ISL8488IBZ can therefore serve as the physical-layer endpoint in equipment that must exchange data reliably over cables or board-level interconnects. The key device attributes are its 5V operation, 4.5V to 5.5V tolerance, full-duplex configuration, 1/1 driver-to-receiver arrangement, 8-SOIC package, low-power BiCMOS implementation, and integrated ESD protection. The family literature identifies applications for high-speed or slew-rate-limited communication. A comparison entry lists a 250kbps operating-rate variant in an 8-pin SOIC, making that data point relevant when matching the correct suffix, but it should not be assumed to describe every device in the family without checking the manufacturer ordering guide. BiCMOS construction combines bipolar and CMOS circuit characteristics to support low-power operation with suitable communications-interface performance. In an RS-485 design, the driver converts a logic-level signal into a differential pair, and the receiver detects the voltage difference between the pair. Full duplex separates the transmit and receive paths so the device can communicate in both directions simultaneously, unlike a half-duplex implementation that must share bus drivers and control signal direction. Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, point-to-point RS-422 links, and RS-485 communications nodes. The full-duplex arrangement is particularly useful when each equipment enclosure needs an independent communication channel rather than a shared half-duplex bus. The 8-pin SOIC package also makes the device practical for conventional surface-mount PCB assembly. PCB design should preserve the differential signal topology, keep the driver and receiver ground connections compact, and route the balanced pair away from switching nodes. External termination and biasing must follow the selected RS-485 or RS-422 network topology. The 4.5V to 5.5V supply range also requires decoupling close to the device so transient current and supply noise do not degrade signal integrity. This product page combines device identification, electrical constraints, interface selection guidance, strict same-package replacement information, and application-specific design guidance. It also distinguishes the ISL8488IBZ from related suffix variants and highlights which parameters require verification in the manufacturer datasheet before production release.

RFQ Kontak
ISL8488IP - 250kbps Full-Duplex RS-485/RS-422 | Renesas
ISL8488IP

ISL8488IP - 250kbps Full-Duplex RS-485/RS-422 | Renesas

The Renesas Electronics ISL8488IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver operating at up to 250 kbps, supplied in an 8-pin plastic DIP package. The device is designed for bidirectional industrial data links and combines a transmitter, receiver, and bus-driver/receiver functions without separate receive or transmit enable pins. Its slew-rate-limited operation helps reduce unwanted high-frequency signal content on longer RS-485 networks. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential bus voltages and converts received differential bus signals back into CMOS-compatible logic. In the broader electronics hierarchy, it is an interface IC within the transceiver family, designed for reliable point-to-point or multipoint communication over cables and industrial backplanes. The ISL8488IP supports both RS-485 and RS-422 system requirements while operating from a single 5 V supply. Key verified characteristics include a 250 kbps maximum signaling rate, full-duplex operation, 5 V supply operation, integrated RS-485/RS-422 transceiver functionality, and slew-rate-limited signaling. The absence of dedicated transmit and receive enable inputs is useful in applications where the interface direction is fixed or managed elsewhere. Its low-power design is intended for embedded industrial, communications, instrumentation, and control systems where reduced energy use and controlled edge rates are important. The device combines differential bus outputs with a receive path designed for data-link applications. Because the ISL8488IP is slew-rate limited, engineers should evaluate its 250 kbps rating against protocol timing, cable length, termination requirements, and the waveform behavior of the connected system. The 8-PDIP package favors through-hole construction, thermal management through the printed-circuit board, and applications that favor a conventional DIP footprint over a surface-mount package. Typical uses include industrial controller links, remote instrumentation, point-to-point communications equipment, factory data acquisition, and embedded systems exchanging commands between a controller and a remote peripheral. Full-duplex operation can simplify systems that continuously require independent transmit and receive paths. The lack of separate enable pins also reduces external control logic, although it may not suit designs that require direction switching or controlled bus tri-state behavior. For a new layout, place the transceiver near the connector and bus entry, route the differential pair as a tightly coupled pair, apply the appropriate termination and protection network, and maintain a continuous ground reference where required by the communication standard. Check the manufacturer datasheet for exact receiver thresholds, driver limits, supply-current values, temperature limits, and absolute maximum ratings before releasing production hardware. This page combines the verified 250 kbps, 5 V, full-duplex, RS-485/RS-422, slew-limited, 8-PDIP, and no-enable characteristics with practical integration guidance. It also distinguishes verified facts from unavailable datasheet details so procurement and engineering teams can identify what must be checked in the full manufacturer documentation.

RFQ Kontak
ISL8489EIB - 5V Full-Duplex RS-485 Transceiver | Renesas
ISL8489EIB

ISL8489EIB - 5V Full-Duplex RS-485 Transceiver | Renesas

The Renesas Electronics ISL8489EIB is a 5 V, full-duplex RS-422/RS-485 transceiver with one driver and one receiver, operating at up to 250 kbps in a 14-pin SOIC package. It operates across a 4.5 V to 5.5 V supply range and is specified from -40°C to +85°C, combining differential bus signaling with integrated ESD protection rated to 15 kV. An RS-485 transceiver is an interface IC that converts logic-level signals into differential RS-485 or RS-422 transmissions and converts received differential signals into logic-level data. The ISL8489EIB supports both standards because its balanced driver and receiver architecture meets the signaling requirements of half-duplex multidrop RS-485 networks and full-duplex point-to-point RS-422 systems. The device belongs to the interface-IC hierarchy and supports bidirectional communication between controllers, sensors, industrial equipment, and field buses. Key features include one transmit driver, one receive receiver, full-duplex operation, 5 V operation, and a maximum data rate of 250 kbps. Its 15 kV ESD protection improves robustness against electrostatic discharge encountered during industrial installation and servicing. The -40°C to +85°C temperature range covers extended industrial environments, while the 14-pin SOIC package supports conventional surface-mount assembly and automated inspection. The BiCMOS implementation combines bipolar and CMOS characteristics, supporting low-power 5 V operation while providing the drive and receive performance required for balanced communication. Full duplex allows the driver and receiver to operate simultaneously, which is useful when transmit and receive paths must remain active. Its 250 kbps maximum rate is appropriate for industrial control buses, instrumentation links, and equipment interfaces that do not require high-speed differential data protocols. Typical applications include industrial automation controllers, RS-485 sensor gateways, motor-control equipment, building-automation nodes, and point-to-point RS-422 links between distributed modules. In a multidrop RS-485 network, the transceiver interfaces a microcontroller UART to a balanced bus while the system supplies termination and biasing components. In a full-duplex implementation, separate differential pairs provide independent transmit and receive paths. PCB design should preserve the balanced trace geometry of the bus and route driver and receiver outputs away from sensitive analog inputs. Place the transceiver close to the board connector to minimize exposed ESD paths, and use the package pin-description table in the manufacturer datasheet when assigning connector and protection-circuitry connections. The 15 kV ESD rating describes the specified protection level, not a guarantee that external surge or lightning protection is unnecessary. This page combines device specifications, verified package and ordering information, application guidance, and same-family drop-in alternatives. It also identifies the electrical details that engineers should confirm against the manufacturer datasheet when qualifying a new RS-422 or RS-485 design.

RFQ Kontak
ISL8489IB - 250kbps RS-485/422 Transceiver | Renesas
ISL8489IB

ISL8489IB - 250kbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8489IB is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps, packaged in a 14-pin SOIC. It combines one driver and one receiver in a single integrated circuit and provides both high-speed and slew-rate-limited operation. The device does not include separate receiver-enable or transmitter-enable controls, making it suitable for continuously enabled balanced communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. These balanced interfaces belong to the broader wired-communication hierarchy and are commonly used where noise immunity, signal integrity, and reliable communication over longer cables are more important than single-ended signaling. The verified product information identifies a 5 V supply, low power consumption, full-duplex operation, support for both RS-485 and RS-422, and data rates up to 250 kbps. Its 14-pin SOIC package supports conventional surface-mount PCB assembly. Because the device lacks separate RX and TX enable pins, it is particularly appropriate for designs that keep both directions of the balanced interface continuously active. The ISL8489 family is described by the manufacturer as a BiCMOS 5 V single-transceiver solution designed for RS-485 and RS-422 balanced communication. Its low-power architecture supports equipment in which multiple interface channels may be present. High-speed or slew-rate-limited operation gives designers a choice according to cable length, topology, and signal-integrity requirements, although exact edge-rate and propagation-delay limits must be confirmed in the manufacturer datasheet. Typical uses include industrial automation links, building-automation equipment, instrumentation, motor-control systems, and industrial data networks. The device can also support point-to-point balanced links where continuous full-duplex operation is preferred. Companion interface devices such as the SN65HVD06D, SP485ECN-L, and SN75174DWR may be relevant when designing connected RS-485 networks or comparing transceiver families. A key design consideration is the absence of independent transmit and receive enables. PCB designers should therefore account for continuous driver activity and verify the driver state, bus termination, protection strategy, and cable topology against the system operating requirements. Decoupling, grounding, and differential-routing practices remain essential for reliable operation on externally accessible industrial buses. This page consolidates verified distributor listings, exact interface and packaging information, sourcing data, comparison fields, and practical design guidance. Where detailed electrical limits or a verified pin mapping were not present in the supplied source data, the missing information is explicitly identified rather than estimated.

RFQ Kontak
ISL8489IB-T - 5V RS-485/RS-422 Transceiver | Renesas Electronics
ISL8489IB-T

ISL8489IB-T - 5V RS-485/RS-422 Transceiver | Renesas Electronics

Renesas Electronics ISL8489IB-T is a 5 V, low-power RS-485/RS-422 interface transceiver packaged in a 14-pin SOIC. The device combines a full RS-485/RS-422 transceiver with low-power operation and supports high-speed or slew-rate-limited communication. Its 5 V supply and 14-pin surface-mount package suit compact industrial, instrumentation, and embedded data-link designs. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals to and from balanced differential pairs. In the RS-485 hierarchy, it connects a host controller or programmable logic device to a field bus. RS-422 provides a point-to-point differential link, while RS-485 supports multipoint bus arrangements subject to proper termination, biasing, and topology. The ISL8489IB-T is identified as a one-driver, one-receiver full transceiver for both RS-422 and RS-485 operation. Its 5 V operating supply supports integration with conventional low-voltage digital logic. The manufacturer describes the family as low-power and usable in high-speed or slew-rate-limited networks, allowing designers to select edge rates suited to their cable length, topology, and signal-integrity requirements. A balanced interface reduces sensitivity to common-mode noise relative to single-ended signaling. This makes the device applicable to industrial control links, data acquisition systems, building automation equipment, and communications equipment operating near motors, relays, power converters, or long external cables. The relevant data rate, driver strength, receiver thresholds, and propagation delays must be confirmed in the manufacturer datasheet before finalizing a high-speed link. The 14-pin SOIC package provides a standard surface-mount footprint suitable for automated assembly. Because RS-485 and RS-422 links depend on board-level implementation, layout should preserve the relationship between the transceiver, protection components, connector, and return path. Correct termination, fail-safe biasing, isolation strategy, and ESD protection are as important as the IC selection. For each RS-485 port, verify the supply voltage, logic thresholds, maximum data rate, driver and receiver enable behavior, thermal conditions, and package pin assignments against the manufacturer datasheet. Pay particular attention to whether a termination resistor is already integrated or must be added externally, and whether the receiver output remains defined when the bus is idle. This page organizes the exact ISL8489IB-T identity, technical specifications, interface-use guidance, source links, and design considerations. It also distinguishes confirmed device facts from parameters that require direct verification in the manufacturer datasheet before high-volume PCB release or production qualification.

RFQ Kontak
ISL8489IP - 5V 250kbps Full-Duplex RS-485/422 | Renesas
ISL8489IP

ISL8489IP - 5V 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8489IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps and packaged in a 14-pin PDIP. The device combines one driver and one receiver in a single package, supports balanced differential communications, and provides a slew-rate-limited alternative for systems that require reduced signal-edge velocity. Its operating characteristics are suited to industrial, instrumentation, communications, and embedded data-acquisition equipment that must connect a host or controller to a balanced bus. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. RS-485 supports multipoint bus communication over long cable runs, while RS-422 commonly supports point-to-point and one-driver topologies. A full-duplex transceiver provides separate paths for transmitting and receiving, unlike half-duplex designs that share a bus and require direction-control logic. The ISL8489IP therefore fits designs that need simultaneous bidirectional communication without sharing a physical signal pair. Key verified features include a 5 V supply requirement, a maximum signaling rate of 250 kbps, full-duplex operation, support for both RS-485 and RS-422, low-power operation, and a slew-rate-limited operating option. The 14-pin PDIP package also provides through-hole compatibility for equipment requiring sockets, prototyping, or manually assembled industrial control boards. The indexed descriptions do not specify separate receiver-enable or transmitter-enable controls, indicating that this version is intended for continuous full-duplex operation. The transceiver architecture provides differential signaling, which is valuable in environments containing industrial machinery, switching supplies, and long interconnects. Differential voltage is measured between the two conductors of a pair rather than relative to ground, improving noise immunity on the receive side. The 250 kbps rate is appropriate for low-to-moderate-speed control and monitoring links where higher signaling rates are unnecessary. The slew-rate-limited behavior can help reduce edge-related ringing and electromagnetic interference when implemented with a correctly terminated network. Typical applications include industrial sensor and actuator networks, factory equipment links, building-control interfaces, laboratory instrumentation, point-to-point data links, and RS-422-compatible control systems. In these systems, the transceiver can connect a UART or microcontroller serial port to a balanced bus. Designers should still verify cable length, topology, grounding, termination, and logic-level compatibility against the complete system requirements before production release. A key design consideration is that the 14-pin PDIP package is not as compact as a surface-mount transceiver. It nevertheless simplifies through-hole construction and socket-based maintenance. The principal engineering trade-off is between 250 kbps operation, low power, full-duplex behavior, and the practical size and assembly requirements of a 14-pin through-hole package. This page consolidates the verified distributor and manufacturer-datasheet indexing information for the ISL8489IP with product-specific engineering guidance, specification gaps, and a transparent replacement assessment. It does not infer unseen electrical limits or substitute candidates whose pin compatibility has not been demonstrated.

RFQ Kontak
ISL8490IB - 5V Low-Power RS-485/RS-422 Transceiver | Renesas
ISL8490IB

ISL8490IB - 5V Low-Power RS-485/RS-422 Transceiver | Renesas

Renesas ISL8490IB is a 5V, low-power RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It is designed for balanced serial data links that require the physical signaling characteristics of both RS-485 and RS-422 interfaces. The verified source material identifies the ISL8490 as a single transceiver supporting high-speed operation or slew-rate-limited operation, allowing it to suit point-to-point RS-422 links as well as multipoint RS-485 networks when used with appropriate bus termination and biasing. Its interface role places it within the transceiver and line-driver hierarchy of communication interface ICs. An RS-485 transceiver converts logic-level digital information into differential signals suitable for balanced industrial communication cables. Differential signaling provides resistance to common-mode noise and allows communication over longer cable runs than a single-ended interface. An RS-422 transceiver similarly uses differential signaling, normally in a point-to-point topology. The ISL8490IB therefore serves as an interface between a digital controller or host and physical copper wiring while placing the high-voltage, high-current bus activity on the transceiver side of the circuit. The principal verified feature is its 5V supply operation. This places it among low-voltage CMOS interface devices intended for systems with compatible digital logic rails. The part is described as low power and as supporting either high-speed or slew-rate-limited communication. High-speed operation prioritizes data throughput, while slew-rate limiting reduces transition-edge energy and can help control electromagnetic interference and ringing on slower networks. Exact data-rate, supply-current, differential-output, input-threshold, and temperature-range values must be confirmed in the manufacturer datasheet before a design is released. Typical uses include industrial RS-485 links, point-to-point RS-422 interconnects, instrumentation, factory automation, building controls, and embedded communication networks. In each case, the transceiver is placed between the controller UART or logic interface and the A/B differential pair. Appropriate cable routing, common-mode grounding, surge protection, termination, and fail-safe biasing remain important parts of the complete interface. Designers should preserve the exact pin mapping and verify the required driver-enable, receiver-enable, termination, and exposed-pad details against the ISL8490 manufacturer datasheet. This page consolidates verified product identity, package information, source links, application guidance, and engineering considerations that are not presented together on a basic distributor listing.

RFQ Kontak
ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas
ISL8490IB-T

ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8490IB-T is a 5 V, single-channel RS-485/RS-422 transceiver built with BiCMOS technology and supplied in an 8-pin SOIC package. It combines one driver and one receiver in one package, supports both RS-485 and RS-422 balanced communication, and provides a low-power interface for industrial and instrumentation links. The device is designed for applications requiring either high-speed operation or slew-rate-limited signaling. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives differential signals back into logic-level outputs. RS-485 supports multipoint, half-duplex buses and is widely used in industrial automation, while RS-422 supports point-to-point and multidrop balanced links. The ISL8490IB-T belongs to the interface-IC hierarchy as a physical-layer communication device between a host controller and a balanced physical layer. The principal device characteristics include a 5 V supply, a 1/1 driver-to-receiver configuration, full RS-422 and RS-485 operation, low power consumption, and either high-speed or slew-rate-limited performance. These features make the device useful when a compact interface must support balanced differential signaling in a small PCB footprint. Its 8-pin SOIC construction also simplifies assembly and inspection on both through-hole-compatible boards and mixed-technology assemblies. BiCMOS implementation combines bipolar and CMOS characteristics within the interface circuit. In this transceiver family, that architecture supports low-power operation while preserving the drive and receive performance needed for balanced communication links. The manufacturer describes the ISL8490 series as devices specified for operation across a 10% supply variation around 5 V, allowing design attention to remain focused on interface margins and system-level power behavior. Typical uses include industrial sensor buses, factory automation equipment, process-control interfaces, building-control networks, and communications ports that connect a UART or controller to an RS-485 or RS-422 cable. In half-duplex RS-485 systems, driver-enable control can determine the bus direction. In full-duplex RS-422 systems, the driver and receiver can remain active without contention because the two channels use separate differential pairs. PCB design should preserve the symmetry of each differential pair, provide a continuous ground reference, and route the balanced lines away from clocks, switching nodes, and other high-current paths. Decoupling capacitors should be placed close to the supply and ground pins. External termination and biasing remain application-dependent and should be configured from the cable length, topology, node count, and driver state rather than added indiscriminately. This product overview combines the device identity, RS-485/RS-422 application context, package information, and practical implementation guidance. It is designed to help engineers identify the correct transceiver function and plan a robust balanced-communication layout without conflating protocol requirements, termination practice, and device-level capabilities.

RFQ Kontak
ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas
ISL8490IBZ

ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas

The Renesas Electronics ISL8490IBZ is a 5 V, full-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin SOIC package. It provides one balanced driver and one balanced receiver, supports a 4.5 V to 5.5 V supply range, and presents a single unit load to an RS-485 bus. The device is configured for full-duplex communication with separate transmit and receive paths. An RS-485/RS-422 transceiver is an interface integrated circuit that converts between single-ended logic signals and differential balanced-line signals. Differential signaling improves noise immunity and allows reliable communication over longer cables or higher-noise industrial environments. The transceiver category belongs to interface ICs within the broader semiconductor hierarchy and is commonly used for multidrop industrial buses, point-to-point links, instrumentation, and building-control networks. Key characteristics include a 5 Mbps maximum data rate, BiCMOS operation, full-duplex configuration, and operation from a 4.5 V to 5.5 V supply. The ISL8490IBZ is designed for systems that require separate differential transmit and receive lines. Its single-unit-load bus loading allows it to participate in conventional RS-485 networks while reducing the number of nodes permitted by a higher unit-load device. The electrical architecture uses a differential driver for balanced bus outputs and a differential receiver for detecting small logic-level voltages. Receiver and driver-enable inputs support local control of bus direction and receiver state. Because the part provides separate transmit and receive paths, no multidrop half-duplex direction-control multiplexing is required, which simplifies full-duplex point-to-point and dual-bus designs. Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, RS-422-compatible equipment, and isolated or non-isolated communication modules. The 5 Mbps capability is suitable for data links above the slower rates commonly associated with legacy RS-485 systems, while the 8-pin SOIC footprint supports compact board construction. When laying out the circuit, route the differential pair as a tightly coupled pair with continuous ground reference, terminate the far end of each differential bus, and keep transceiver switching and protection circuitry away from sensitive receive nodes. Confirm that the selected termination, protection, isolation, and connector strategy preserves the signal integrity required at the intended data rate and cable length.

RFQ Kontak
ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8490IP

ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8490IP is a 5 V, low-power, full-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and an 8-pin PDIP package. The device supports both high-speed RS-485 communication and RS-422 point-to-point links, while its separate receiver and driver enable paths provide flexibility for half-duplex control through the DE and RE inputs. Its operating-temperature range is -40°C to +85°C, making it suitable for industrial and commercial equipment requiring a through-hole interface solution. A transceiver is an interface IC that converts digital logic signals into balanced differential signals for reliable communication over noisy or long cable runs. In the hierarchy, the ISL8490IP is a line transceiver, a type of interface IC and communications semiconductor. RS-485 supports multiple drivers and receivers on a shared bus, whereas RS-422 commonly uses a dedicated driver and receiver for point-to-point or multidrop networks. This transceiver supports both protocols and therefore provides a useful interface between CMOS/TTL logic and balanced cabling. The verified headline specifications are a 5 V supply, 5 Mbps maximum data rate, 70 mV receiver hysteresis, 1 driver, 1 receiver, full-duplex operation, and support for RS-422 and RS-485. These parameters place the part in the low-power, high-speed or slew-rate-limited transceiver category described by the manufacturer documentation. The 8-pin PDIP format also permits conventional through-hole PCB assembly rather than requiring a fine-pitch surface-mount land pattern. Technically, the balanced driver and receiver provide noise immunity over longer interconnects than ordinary single-ended logic. Receiver hysteresis helps distinguish signaling states in the presence of noise, while the 5 Mbps capability supports communication rates beyond the slow speeds commonly used by legacy RS-485 systems. Because the exact input capacitance, output timing, supply-current limits, and slew-rate settings are not included in the supplied verified excerpts, design engineers should confirm them in the manufacturer datasheet before finalizing timing, termination, and decoupling. Typical uses include industrial controllers, building automation equipment, data acquisition systems, instrumentation, industrial networking equipment, and embedded control links. For an RS-485 bus, the circuit requires suitable line termination and biasing. For RS-422, driver and receiver connections should follow the source and destination topology specified by the system architecture rather than being treated as a multi-drop RS-485 bus. The principal design consideration is signal integrity at 5 Mbps. Layout should minimize the distance between the transceiver, protection devices, connector, and differential pair, while keeping the two conductors of each balanced pair closely coupled. Decoupling close to the supply pin, controlled ground return paths, and appropriate surge protection help maintain reliable operation in industrial environments. This page consolidates the verified distributor and manufacturer-document information with lifecycle status, procurement guidance, application fit, package details, and honest replacement limitations. It distinguishes confirmed facts from specifications that still require verification from the full Renesas datasheet.

RFQ Kontak
ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas
ISL8491EIB

ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8491EIB is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver with ±15kV ESD protection, slew-rate-limited high-speed operation, and separate receive and transmit output-enable pins. It is packaged in a 14-lead SOIC and is designed for industrial communication links requiring both differential transmit and differential receive capability. An RS-485/RS-422 transceiver is an interface IC that converts digital logic signals into balanced differential signals and receives differential signals from a cable. These differential signaling methods improve noise immunity and allow reliable data transmission over longer cable distances than single-ended interfaces. The ISL8491EIB supports both RS-485 and RS-422 operating modes, while its full-duplex arrangement permits simultaneous transmission and reception when the bus wiring and termination network are configured appropriately. The main device characteristics are a 5V supply, ±15kV ESD protection, low-power operation, high-speed communication with slew-rate limiting, and separate receive and transmit output-enable pins. The separate enables allow the transmitter and receiver to be controlled independently, which is useful in multidrop RS-485 networks where a node must listen while preventing bus contention. The 14-lead SOIC package is a standard surface-mount format compatible with conventional PCB assembly methods. The ISL8491EIB is based on the Renesas ISL8491E family, which is positioned for robust industrial data links. ESD protection is particularly important because RS-485 interfaces are commonly exposed to user-accessible cables and connector transients. Slew-rate limiting helps control edge transitions on the bus and reduce unwanted high-frequency content, while the low-power design supports systems where standby and active-state efficiency are important. The exact data rate, receiver thresholds, common-mode limits, and supply-current limits should be confirmed in the manufacturer datasheet before final design release. Typical applications include industrial automation controllers, factory data buses, building automation equipment, instrumentation links, motor-control systems, and embedded serial interfaces. The full-duplex architecture is especially appropriate for point-to-point RS-422 links and full-duplex RS-485 networks where transmit and receive paths operate simultaneously. Independent enables can support bus segmentation, controlled test modes, or systems that need to mute a receiver during certain operating states. Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, particularly for enable inputs, ground connections, driver outputs, and receiver inputs. The external network must include appropriate termination, biasing, protection, and decoupling components for the selected RS-485 or RS-422 topology. Confirm the exact ISL8491EIB ordering code, package marking, and operating-temperature limits before production release. This page consolidates the available ISL8491EIB product information, direct replacement options, package information, and practical interface-design guidance to support faster component evaluation and sourcing decisions.

RFQ Kontak