Mga Produkto (44,000+)

KSZ8563RNXV-TR - 3-Port 10/100 Ethernet Switch | Microchip (Tape & Reel)
KSZ8563RNXV-TR

KSZ8563RNXV-TR - 3-Port 10/100 Ethernet Switch | Microchip (Tape & Reel)

Microchip Technology KSZ8563RNXV-TR is a three-port 10/100 Ethernet switch with an IEEE 802.3 compliant layer-2+ managed switching core, two integrated 10BASE-T/100BASE-TX PHYs, and one configurable MAC port supporting RGMII, MII, or RMII connectivity. The device is housed in a 64-pin VQFN package measuring 8 mm by 8 mm. It also provides I2C and SPI management interfaces for configuration and control. An Ethernet switch is a network-semiconductor device that connects multiple Ethernet ports and moves frames according to MAC addresses while adding layer-2 management, prioritization, and traffic-management functions. The KSZ8563 combines two copper Ethernet PHYs with a configurable host interface, making it suitable for embedded systems that need to consolidate wired network connections without using a separate external switch. Key features include three-port switching, integrated 10BASE-T and 100BASE-TX transceivers, IEEE 802.3 compliance, and support for RGMII, MII, and RMII host interfaces. IEEE 1588v2 and 802.1AS time synchronization, AVB traffic handling, Energy Efficient Ethernet, Wake-on-LAN, QoS, LinkMD+, and fault-recovery functions broaden its suitability for industrial, automotive, and communications equipment. The configurable third MAC port allows a host processor or controller to connect through a parallel RGMII interface, MII interface, or lower-pin-count RMII interface. Management access through I2C or SPI supports software initialization, status monitoring, address-table administration, and switch configuration. These features combine hardware connectivity with firmware-controlled layer-2 functions in one package. Typical uses include industrial Ethernet gateways, automotive head-unit networking, building-automation controllers, embedded network appliances, and factory equipment with multiple wired ports. A compact system design can use the two integrated PHY ports for external copper links while reserving the configurable MAC port for communication with a host processor. PCB implementation requires careful attention to the 64-pin VQFN land pattern, exposed-pad thermal management, high-speed RGMII or RMII signal routing, and Ethernet magnetics or integrated magnetics connected to the copper PHY ports. Follow the manufacturer pin-description table and reference layout when assigning tracks and component placement. This page combines the manufacturer device description, exact orderable-package information, interface and standards details, sourcing guidance, and practical implementation considerations into a compact engineering reference for evaluating the KSZ8563RNXV-TR.

RFQ Kontak
KSZ8567RTXI - 7-Port 10/100 AVB Ethernet Switch | Microchip
KSZ8567RTXI

KSZ8567RTXI - 7-Port 10/100 AVB Ethernet Switch | Microchip

The Microchip Technology KSZ8567RTXI is a fully integrated Layer-2 managed seven-port 10/100 Ethernet switch with five integrated PHYs, designed to exceed Automotive AEC-Q100 Grade 2 (-40C to +105C) and EMC requirements. It is offered in a 128-pin TQFP-EP (14x14 mm) package and supports both I2C and SPI host management interfaces. A managed Ethernet switch is a Layer-2 networking IC that forwards Ethernet frames between multiple ports using MAC address learning, VLAN tagging, QoS prioritization, and IGMP snooping. It sits hierarchically between the PHY layer and the network host processor, enabling deterministic low-latency communication on automotive, industrial, and AVB/TSN time-sensitive networks. The KSZ8567 family adds Audio Video Bridging (AVB) hardware timestamping and TSN-ready QoS, extending the basic managed-switch feature set with synchronized media-stream support. Key features include seven 10/100 Mbps ports (five with integrated 10BASE-T/100BASE-TX PHYs, two RGMII/MII/RMII host-facing MACs), IEEE 802.1Q VLAN support, 802.1p QoS with four priority queues, IEEE 1588v2 and 802.1AS time stamping, AVB hardware assist, and a 1.2V core with 3.3V I/O supply. The device also includes cable-diagnostics, on-chip termination, and Energy-Efficient Ethernet (EEE) support for low-power idle states. Architecturally, the KSZ8567RTXI integrates five physical-layer transceivers, a wire-speed store-and-forward switching engine, per-port buffer memory, and a management interface block exposing I2C, SPI, MIIM, and GPIOs. AEC-Q100 Grade 2 qualification, enhanced ESD protection, and on-chip PHY terminations simplify EMC-compliant board design in automotive and industrial environments. Typical applications include automotive in-vehicle networking gateways, industrial Ethernet switches, AVB/TSN bridges for professional audio/video equipment, building automation controllers, and IEC 61850 / IEC 62439 industrial process switches. The integrated PHYs minimize external magnetics count, while AVB/TSN hardware accelerates deterministic Ethernet streams. When designing with the KSZ8567RTXI, observe the 50-ohm single-ended PHY trace impedance with continuous ground reference, decouple all four supply rails (3.3V, 2.5V, 1.8V, 1.2V) close to the package, and provide an exposed-pad solder connection for thermal dissipation. MDI traces to magnetics should be kept to under 25 mm and routed as 100-ohm differential pairs to meet IEEE 802.3 return-loss masks. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Kontak
KSZ8567RTXI-TR - 7-Port 10/100 AVB Ethernet Switch | Microchip (Tape & Reel)
KSZ8567RTXI-TR

KSZ8567RTXI-TR - 7-Port 10/100 AVB Ethernet Switch | Microchip (Tape & Reel)

The Microchip Technology KSZ8567RTXI-TR is a fully integrated Layer-2 managed seven-port 10/100 Ethernet switch with five integrated PHYs, designed to exceed Automotive AEC-Q100 Grade 2 (-40C to +105C) and EMC requirements. It is offered in a 128-pin TQFP-EP (14x14 mm) package and supports both I2C and SPI host management interfaces. A managed Ethernet switch is a Layer-2 networking IC that forwards Ethernet frames between multiple ports using MAC address learning, VLAN tagging, QoS prioritization, and IGMP snooping. It sits hierarchically between the PHY layer and the network host processor, enabling deterministic low-latency communication on automotive, industrial, and AVB/TSN time-sensitive networks. The KSZ8567 family adds Audio Video Bridging (AVB) hardware timestamping and TSN-ready QoS, extending the basic managed-switch feature set with synchronized media-stream support. Key features include seven 10/100 Mbps ports (five with integrated 10BASE-T/100BASE-TX PHYs, two RGMII/MII/RMII host-facing MACs), IEEE 802.1Q VLAN support, 802.1p QoS with four priority queues, IEEE 1588v2 and 802.1AS time stamping, AVB hardware assist, and a 1.2V core with 3.3V I/O supply. The device also includes cable-diagnostics, on-chip termination, and Energy-Efficient Ethernet (EEE) support for low-power idle states. Architecturally, the KSZ8567RTXI-TR integrates five physical-layer transceivers, a wire-speed store-and-forward switching engine, per-port buffer memory, and a management interface block exposing I2C, SPI, MIIM, and GPIOs. AEC-Q100 Grade 2 qualification, enhanced ESD protection, and on-chip PHY terminations simplify EMC-compliant board design in automotive and industrial environments. Typical applications include automotive in-vehicle networking gateways, industrial Ethernet switches, AVB/TSN bridges for professional audio/video equipment, building automation controllers, and IEC 61850 / IEC 62439 industrial process switches. The integrated PHYs minimize external magnetics count, while AVB/TSN hardware accelerates deterministic Ethernet streams. When designing with the KSZ8567RTXI-TR, observe the 50-ohm single-ended PHY trace impedance with continuous ground reference, decouple all four supply rails (3.3V, 2.5V, 1.8V, 1.2V) close to the package, and provide an exposed-pad solder connection for thermal dissipation. MDI traces to magnetics should be kept to under 25 mm and routed as 100-ohm differential pairs to meet IEEE 802.3 return-loss masks. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Kontak
KSZ8567STXI - 7-Port Managed 10/100 Ethernet Switch | Microchip
KSZ8567STXI

KSZ8567STXI - 7-Port Managed 10/100 Ethernet Switch | Microchip

Microchip Technology KSZ8567STXI is a fully integrated, managed seven-port 10/100 Ethernet switch with five integrated 10/100BASE-T PHYs, I2C and SPI management interfaces, and a 128-TQFP exposed-pad package measuring 14 x 14 mm. The device is designed for Automotive AEC-Q100 Grade 2 requirements over -40°C to +105°C and exceeds specified EMC requirements. Its managed Layer 2 architecture supports advanced networking features including IEEE 1588 v2, AVB, Energy Efficient Ethernet, Wake-on-LAN, QoS, LinkMD+, and fault recovery. An Ethernet switch is a Layer 2 network-semiconductor device that receives Ethernet frames on one port and forwards them toward the appropriate destination port using MAC-address tables. A managed switch adds configuration, monitoring, traffic prioritization, timing, and recovery functions that distinguish it from a basic unmanaged switch. The KSZ8567 integrates seven-port switching, five copper PHYs, a host-management interface, and automotive-oriented robustness into one device. Five of the seven ports include 10/100BASE-T copper PHYs. The switching fabric supports full-duplex 100 Mbit/s copper links for local industrial, automotive, communications, and embedded network equipment. The integrated PHY reduces external magnetics and copper-interface component count, while the I2C and SPI interfaces allow a host controller to configure registers, monitor port status, and implement network-management functions. The KSZ8567 family includes fault-recovery, IEEE 1588 v2 precision-time support, Audio Video Bridging, Energy Efficient Ethernet, Wake-on-LAN, and QoS capabilities. IEEE 1588 v2 timing can support synchronized traffic in systems requiring precise time distribution. AVB and QoS are useful when deterministic traffic must share Ethernet links with less timing-critical network traffic. EEE can reduce link energy where supported by the complete network, while LinkMD+ provides cable diagnostics that simplify commissioning and fault isolation. Typical applications include automotive Ethernet gateways, industrial control systems, networked sensors, factory equipment, embedded service interfaces, and compact Ethernet aggregation units. The 128-TQFP exposed-pad package supports substantial copper-based thermal dissipation on multilayer PCBs, but thermal performance still depends on the pad, vias, copper area, and ambient conditions. For a new design, verify the complete pin assignment, reference clock requirements, magnetic-component recommendations, register initialization, and layout guidance in the manufacturer datasheet. Preserve the exposed-pad land pattern and connect it to the intended ground plane according to the package drawing. When assessing a second source, confirm pinout and firmware behavior in addition to the number of ports; a functionally similar Ethernet component is not automatically a drop-in replacement. This page combines manufacturer device information, package and interface details, commercial sourcing guidance, and engineering-focused replacement criteria. It helps engineers identify whether the KSZ8567STXI matches a seven-port managed-switch requirement before beginning PCB layout and software configuration.

RFQ Kontak
KSZ8567STXI-TR - 7-Port Managed 10/100 Ethernet Switch | Microchip (Tape & Reel)
KSZ8567STXI-TR

KSZ8567STXI-TR - 7-Port Managed 10/100 Ethernet Switch | Microchip (Tape & Reel)

Microchip Technology KSZ8567STXI-TR is a fully integrated, managed seven-port 10/100 Ethernet switch with five integrated 10/100BASE-T PHYs, I2C and SPI management interfaces, and a 128-TQFP exposed-pad package measuring 14 x 14 mm. The device is designed for Automotive AEC-Q100 Grade 2 requirements over -40°C to +105°C and exceeds specified EMC requirements. Its managed Layer 2 architecture supports advanced networking features including IEEE 1588 v2, AVB, Energy Efficient Ethernet, Wake-on-LAN, QoS, LinkMD+, and fault recovery. An Ethernet switch is a Layer 2 network-semiconductor device that receives Ethernet frames on one port and forwards them toward the appropriate destination port using MAC-address tables. A managed switch adds configuration, monitoring, traffic prioritization, timing, and recovery functions that distinguish it from a basic unmanaged switch. The KSZ8567 integrates seven-port switching, five copper PHYs, a host-management interface, and automotive-oriented robustness into one device. Five of the seven ports include 10/100BASE-T copper PHYs. The switching fabric supports full-duplex 100 Mbit/s copper links for local industrial, automotive, communications, and embedded network equipment. The integrated PHY reduces external magnetics and copper-interface component count, while the I2C and SPI interfaces allow a host controller to configure registers, monitor port status, and implement network-management functions. The KSZ8567 family includes fault-recovery, IEEE 1588 v2 precision-time support, Audio Video Bridging, Energy Efficient Ethernet, Wake-on-LAN, and QoS capabilities. IEEE 1588 v2 timing can support synchronized traffic in systems requiring precise time distribution. AVB and QoS are useful when deterministic traffic must share Ethernet links with less timing-critical network traffic. EEE can reduce link energy where supported by the complete network, while LinkMD+ provides cable diagnostics that simplify commissioning and fault isolation. Typical applications include automotive Ethernet gateways, industrial control systems, networked sensors, factory equipment, embedded service interfaces, and compact Ethernet aggregation units. The 128-TQFP exposed-pad package supports substantial copper-based thermal dissipation on multilayer PCBs, but thermal performance still depends on the pad, vias, copper area, and ambient conditions. For a new design, verify the complete pin assignment, reference clock requirements, magnetic-component recommendations, register initialization, and layout guidance in the manufacturer datasheet. Preserve the exposed-pad land pattern and connect it to the intended ground plane according to the package drawing. When assessing a second source, confirm pinout and firmware behavior in addition to the number of ports; a functionally similar Ethernet component is not automatically a drop-in replacement. This page combines manufacturer device information, package and interface details, commercial sourcing guidance, and engineering-focused replacement criteria. It helps engineers identify whether the KSZ8567STXI-TR matches a seven-port managed-switch requirement before beginning PCB layout and software configuration.

RFQ Kontak
KSZ8721B - 2.5V 10/100 Ethernet PHY | Microchip
KSZ8721B

KSZ8721B - 2.5V 10/100 Ethernet PHY | Microchip

The Microchip Technology KSZ8721B is a 2.5 V single-supply 10Base-T/100Base-TX/FX Ethernet physical-layer transceiver with a 48-SSOP package. It supports MII and RMII host interfaces, integrates the 10BaseT and 100BaseTX physical-layer functions, and provides a low-voltage, low-power Ethernet interface for embedded systems. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital frame data into signals suitable for copper twisted-pair or fiber media and converts received signals back into digital data. The KSZ8721B belongs to the Ethernet interface hierarchy: transceiver -> physical layer -> network interface IC -> semiconductor. Its 2.5 V operating supply is suitable for low-power embedded platforms that already provide compatible I/O levels. The KSZ8721B supports 10Base-T and 100Base-TX operation, along with 100Base-FX capability as identified in the product description. The MII and RMII host interfaces support different host-side connection styles, allowing the same PHY to serve systems with parallel media-independent or reduced media-independent interfaces. The device also includes integrated 10Base-T functions, reducing the need for separate medium-access and coding functions around the PHY. The verified product listing describes KSZ8721B as a 48-SSOP part and identifies it as a 10/100 Base-TX/FX MII physical-layer transceiver. The manufacturer’s related datasheet snippet identifies the KS8721B/BT family as operating at 2.5 V and containing PMA, PMD, and PCS functions. Electrical limits, exact pin functions, temperature limits, clocking requirements, and layout guidance should be taken from the manufacturer datasheet before final design release. Typical uses include industrial Ethernet controllers, embedded control systems, communication modules, test equipment, and low-power network appliances. The MII interface is useful when the host controller requires a conventional parallel bus, while RMII can reduce the number of host-side signals in compatible designs. The 2.5 V supply also helps system designers manage power budgets on compact embedded boards. When laying out the circuit, place the PHY, magnetics, connector, decoupling, and clock or reset components according to the manufacturer reference layout. Validate signal integrity across MII or RMII timing, provide continuous reference planes, and verify cable and magnetics compatibility. The KSZ8721B is not a general-purpose connector or power device, so its SOA field is not applicable. This page consolidates the verified manufacturer and distributor information for the KSZ8721B, including package identity, interface type, sourcing links, practical application guidance, and clearly marked data gaps. It is intended to accelerate engineering evaluation while avoiding unsupported electrical claims.

RFQ Kontak
KSZ8721B-TR - 10/100 Ethernet PHY Transceiver | Microchip (Tape & Reel)
KSZ8721B-TR

KSZ8721B-TR - 10/100 Ethernet PHY Transceiver | Microchip (Tape & Reel)

The Microchip Technology KSZ8721B-TR is a single-channel 10/100 Base-TX/FX Ethernet physical-layer transceiver operating from a 3.3 V single supply in a 48-pin TQFP package measuring 7 mm by 7 mm. According to the manufacturer product information, the device supports both MII and RMII host interfaces, 10BASE-T and 100BASE-TX copper links, and 100BASE-FX fiber links. Its core role is to connect a digital Ethernet host interface to an Ethernet medium through integrated PCS and PMA functions. An Ethernet PHY transceiver is an interface IC that converts parallel digital Ethernet data into physical signaling for copper or optical media, while receiving and decoding incoming signals. The KSZ8721 belongs to the PHY hierarchy: Ethernet interface IC, physical-layer transceiver, 10/100 Ethernet PHY, and network interface semiconductor. Supporting both copper and fiber media makes it useful in industrial control, embedded networking, communications equipment, and factory automation systems. Verified source information identifies the KSZ8721 as a 10BaseT/100BaseTX/FX physical-layer transceiver with MII and RMII host connectivity. The RMII option can reduce host pin requirements compared with a parallel MII arrangement, which is valuable when conserving connector and processor I/O resources. The 100BASE-FX capability supports fiber links where electrical copper reach or electromagnetic environments make optical media preferable. Exact PHY tolerances, clock requirements, link-distance targets, and electrical thresholds must be confirmed in the manufacturer datasheet before design release. The 48-TQFP surface-mount package is suitable for automated PCB assembly and compact multilayer boards. Its exact pin functions, exposed-pad arrangement, supply connections, and grounding requirements were not supplied in the verified excerpts, so they must not be inferred. Designers should preserve the manufacturer's recommended magnetics, termination network, RJ45 layout, fiber-isolation boundary, and high-speed trace topology. Decoupling and return paths are particularly important because Ethernet PHY performance depends on clean references and controlled common-mode behavior. Typical uses include 10/100 Ethernet links in embedded controllers, industrial Ethernet gateways, serial-to-Ethernet equipment, network switches, test instruments, and optical-to-copper media converters. The combination of MII, RMII, copper, and fiber support lets one device bridge several common legacy network-interface architectures. Exact suitability for a particular MAC, processor, transformer, optical module, or cable length must be verified against the complete datasheet and system timing requirements. This page consolidates the verified manufacturer, distributor, and datasheet-index information while clearly separating missing technical data. Its engineering value is the application guidance, sourcing context, and explicit compatibility boundaries rather than guessed specifications. Before purchasing or laying out a replacement board, verify lifecycle status, exact electrical limits, pinout, media support, and package details against the authoritative Microchip documentation. This page also distinguishes verified facts from open engineering questions. Because the excerpts do not supply a complete electrical table, package drawing, lifecycle statement, or pin-level map, each missing item is marked rather than estimated. That conservative approach is essential for Ethernet hardware, where an incorrect pin assignment, unsupported interface mode, or inappropriate power assumption can prevent link negotiation or damage a design.

RFQ Kontak
KSZ8721BA4 - 10/100 Ethernet Transceiver | Microchip Technology
KSZ8721BA4

KSZ8721BA4 - 10/100 Ethernet Transceiver | Microchip Technology

The Microchip Technology KSZ8721BA4 is a single-port 10/100 Mbps Ethernet transceiver with integrated Media Access Controller and Physical Layer functions, supporting both MII and RMII protocols in a 48-SSOP package. The device is intended for embedded networking equipment requiring a compact Ethernet interface and flexible host connectivity options. An Ethernet transceiver combines the physical-layer functions required to transmit and receive data over twisted-pair cabling with the MAC functions needed to organize frames and manage network access. The KSZ8721BA4 can operate through either the Media Independent Interface, which provides a wider parallel data and control interface, or the Reduced Media Independent Interface, which uses fewer signals and is useful where board space and pin count are constrained. In the broader electronics hierarchy, this device is an interface IC, network transceiver, Ethernet PHY and MAC integration. Verified distributor information identifies the KSZ8721BA4 as a 1/1 transceiver supporting full-duplex 10/100 Mbps Ethernet, MII and RMII protocols, and a 48-SSOP package. The single-port configuration allows one Ethernet network connection on an embedded controller or industrial system. Its support for both MII and RMII gives designers a choice between a more parallel host interface and a reduced-pin interface without changing the transceiver family. The integrated MAC and PHY arrangement reduces the external component count required for a basic Ethernet endpoint. In an RMII implementation, the host controller connects to the transceiver through the reduced interface, while the transceiver handles the physical signaling and network framing functions. In an MII implementation, the device exposes the additional parallel signals required by the fuller interface. The exact operating voltage, clock requirements, transceiver pin assignments and electrical timing limits are not present in the supplied verified data and should be confirmed against the manufacturer datasheet. Typical applications include industrial Ethernet control systems, embedded routers, network-interface modules, factory equipment, building automation controllers and compact communications products. The MII support is useful when the host system expects the conventional parallel Ethernet interface, while RMII is generally preferable where connector density and PCB routing simplicity matter. The part is supplied in a surface-mount 48-SSOP package, allowing automated board assembly rather than through-hole insertion. When designing around the KSZ8721BA4, confirm the selected MII or RMII host interface, power architecture, clocking method, magnetic-interface implementation and Ethernet magnetics before layout release. Check the manufacturer datasheet for the exact reference circuit, decoupling requirements, termination values and pin names; these details are not specified in the supplied search results and should not be inferred from generic Ethernet transceiver designs. This product page combines the verified distributor and manufacturer information for the KSZ8721BA4 with practical interface-selection guidance, package details, sourcing context and a conservative replacement analysis. It is intended to help engineers identify the correct Ethernet transceiver and verify its mechanical, electrical and procurement requirements before committing a new design to production.

RFQ Kontak
KSZ8721BA4TR - 10/100 Ethernet Transceiver | Microchip Technology (Tape & Reel)
KSZ8721BA4TR

KSZ8721BA4TR - 10/100 Ethernet Transceiver | Microchip Technology (Tape & Reel)

The Microchip Technology KSZ8721BA4TR is a single-port 10/100 Mbps Ethernet transceiver with integrated Media Access Controller and Physical Layer functions, supporting both MII and RMII protocols in a 48-SSOP package. The device is intended for embedded networking equipment requiring a compact Ethernet interface and flexible host connectivity options. An Ethernet transceiver combines the physical-layer functions required to transmit and receive data over twisted-pair cabling with the MAC functions needed to organize frames and manage network access. The KSZ8721BA4TR can operate through either the Media Independent Interface, which provides a wider parallel data and control interface, or the Reduced Media Independent Interface, which uses fewer signals and is useful where board space and pin count are constrained. In the broader electronics hierarchy, this device is an interface IC, network transceiver, Ethernet PHY and MAC integration. Verified distributor information identifies the KSZ8721BA4TR as a 1/1 transceiver supporting full-duplex 10/100 Mbps Ethernet, MII and RMII protocols, and a 48-SSOP package. The single-port configuration allows one Ethernet network connection on an embedded controller or industrial system. Its support for both MII and RMII gives designers a choice between a more parallel host interface and a reduced-pin interface without changing the transceiver family. The integrated MAC and PHY arrangement reduces the external component count required for a basic Ethernet endpoint. In an RMII implementation, the host controller connects to the transceiver through the reduced interface, while the transceiver handles the physical signaling and network framing functions. In an MII implementation, the device exposes the additional parallel signals required by the fuller interface. The exact operating voltage, clock requirements, transceiver pin assignments and electrical timing limits are not present in the supplied verified data and should be confirmed against the manufacturer datasheet. Typical applications include industrial Ethernet control systems, embedded routers, network-interface modules, factory equipment, building automation controllers and compact communications products. The MII support is useful when the host system expects the conventional parallel Ethernet interface, while RMII is generally preferable where connector density and PCB routing simplicity matter. The part is supplied in a surface-mount 48-SSOP package, allowing automated board assembly rather than through-hole insertion. When designing around the KSZ8721BA4TR, confirm the selected MII or RMII host interface, power architecture, clocking method, magnetic-interface implementation and Ethernet magnetics before layout release. Check the manufacturer datasheet for the exact reference circuit, decoupling requirements, termination values and pin names; these details are not specified in the supplied search results and should not be inferred from generic Ethernet transceiver designs. This product page combines the verified distributor and manufacturer information for the KSZ8721BA4TR with practical interface-selection guidance, package details, sourcing context and a conservative replacement analysis. It is intended to help engineers identify the correct Ethernet transceiver and verify its mechanical, electrical and procurement requirements before committing a new design to production.

RFQ Kontak
KSZ8721BI - 2.5V 10/100 Ethernet PHY Transceiver | Microchip
KSZ8721BI

KSZ8721BI - 2.5V 10/100 Ethernet PHY Transceiver | Microchip

The Microchip Technology KSZ8721BI is a 2.5 V 10Base-T and 100Base-TX/FX Ethernet physical-layer transceiver with a 1/1 driver-receiver configuration and MII/RMII host interface. It is packaged in a 48-SSOP and is intended for low-voltage, low-power embedded Ethernet designs. According to the Microchip KSZ8721 product page, the device contains the 10Base-T physical medium attachment, 100Base-TX/FX PMD, and media-independent interface functions required to connect a network processor to copper or fiber media hardware. An Ethernet PHY is the analog and digital interface between a host controller and an Ethernet network medium. It converts logical MII or RMII data into differential 10Base-T or 100Base-TX signaling, receives and recovers incoming signals, and provides collision, carrier, and link-status information to the host. The KSZ8721 therefore sits between an Ethernet-capable microcontroller, application processor, or network controller and a magnetics-based Ethernet jack or an external fiber-media interface. The KSZ8721BI operates at 2.5 V to support low-voltage and low-power system requirements. Distributor records identify a 2.375 V to 2.625 V operating supply range, a 48-SSOP package, MII and RMII protocols, and a tube-style shipping format for the KSZ8721BI ordering code. Its 10/100 capability allows a design to support 10 Mbps or 100 Mbps operation while retaining a conventional MII path and an RMII option for host interfaces with fewer pins. The MII interface exposes separate control, data, and status signals in a parallel form, while RMII reduces the host-side signal count for a more compact implementation. Host-side selection depends on the controller's supported clock and data arrangement, so designers should verify MII-versus-RMII configuration against the system controller and required operating mode. The PHY also requires an appropriate clock reference and the correct external magnetics or fiber-media interface implementation. Typical uses include industrial controllers, embedded gateways, set-top boxes, print servers, and legacy Ethernet-equipped embedded systems. In a copper link, the device sits on the line side of an isolation transformer network. In a fiber-oriented design, its 100Base-FX capability can be combined with an external optical transceiver, although fiber-module and magnetics selection remain board-level responsibilities. The principal design consideration is the separation between host-side digital signals and line-side analog signaling. Keep MII or RMII routing short, provide clean clock distribution, use the required decoupling, and follow the manufacturer's reference layout for the media interface. Verify magnetics, termination, and isolation components against the selected 10Base-T or 100Base-TX network topology. This page consolidates manufacturer information, distributor pricing, and engineering guidance for the KSZ8721BI. It also documents verified parameter gaps instead of substituting unverified values, helping designers compare the device accurately before committing a PCB layout to production.

RFQ Kontak
KSZ8721BI-TR - 2.5V 10/100 Ethernet PHY Transceiver | Microchip (Tape & Reel)
KSZ8721BI-TR

KSZ8721BI-TR - 2.5V 10/100 Ethernet PHY Transceiver | Microchip (Tape & Reel)

The Microchip Technology KSZ8721BI-TR is a 2.5 V 10Base-T and 100Base-TX/FX Ethernet physical-layer transceiver with a 1/1 driver-receiver configuration and MII/RMII host interface. It is packaged in a 48-SSOP and is intended for low-voltage, low-power embedded Ethernet designs. According to the Microchip KSZ8721 product page, the device contains the 10Base-T physical medium attachment, 100Base-TX/FX PMD, and media-independent interface functions required to connect a network processor to copper or fiber media hardware. An Ethernet PHY is the analog and digital interface between a host controller and an Ethernet network medium. It converts logical MII or RMII data into differential 10Base-T or 100Base-TX signaling, receives and recovers incoming signals, and provides collision, carrier, and link-status information to the host. The KSZ8721 therefore sits between an Ethernet-capable microcontroller, application processor, or network controller and a magnetics-based Ethernet jack or an external fiber-media interface. The KSZ8721BI-TR operates at 2.5 V to support low-voltage and low-power system requirements. Distributor records identify a 2.375 V to 2.625 V operating supply range, a 48-SSOP package, MII and RMII protocols, and a tube-style shipping format for the KSZ8721BI-TR ordering code. Its 10/100 capability allows a design to support 10 Mbps or 100 Mbps operation while retaining a conventional MII path and an RMII option for host interfaces with fewer pins. The MII interface exposes separate control, data, and status signals in a parallel form, while RMII reduces the host-side signal count for a more compact implementation. Host-side selection depends on the controller's supported clock and data arrangement, so designers should verify MII-versus-RMII configuration against the system controller and required operating mode. The PHY also requires an appropriate clock reference and the correct external magnetics or fiber-media interface implementation. Typical uses include industrial controllers, embedded gateways, set-top boxes, print servers, and legacy Ethernet-equipped embedded systems. In a copper link, the device sits on the line side of an isolation transformer network. In a fiber-oriented design, its 100Base-FX capability can be combined with an external optical transceiver, although fiber-module and magnetics selection remain board-level responsibilities. The principal design consideration is the separation between host-side digital signals and line-side analog signaling. Keep MII or RMII routing short, provide clean clock distribution, use the required decoupling, and follow the manufacturer's reference layout for the media interface. Verify magnetics, termination, and isolation components against the selected 10Base-T or 100Base-TX network topology. This page consolidates manufacturer information, distributor pricing, and engineering guidance for the KSZ8721BI-TR. It also documents verified parameter gaps instead of substituting unverified values, helping designers compare the device accurately before committing a PCB layout to production.

RFQ Kontak
KSZ8721BL - 100Mbps Ethernet PHY | Microchip | LQFP-48
KSZ8721BL

KSZ8721BL - 100Mbps Ethernet PHY | Microchip | LQFP-48

The Microchip KSZ8721BL is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with MII and RMII host interfaces, operating at up to 100 Mbps in a 48-pin LQFP package. It supports a 2.5 V core for low-voltage and low-power operation, includes automatic MDI/MDI-X crossover, and is intended for embedded Ethernet designs requiring copper twisted-pair or fiber connections. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital MAC data into electrical or optical signaling suitable for a network medium and converts received signals back into digital data. The PHY sits between a host controller and the physical network medium, commonly using an MII or RMII interface. The KSZ8721BL therefore belongs to the Ethernet interface hierarchy: transceiver, network interface controller companion, interface IC, and semiconductor. Key verified features include 100 Mbps operation, MII and RMII host-interface support, 10/100BASE-TX and 100BASE-FX capability, automatic MDI/MDI-X crossover, 3.3 V single-supply operation, and a 2.5 V core. The commercial temperature range is 0°C to +70°C. The reported supply current is 151 mA, while the exact pin mapping, package dimensions, transceiver electrical limits, and full timing values are not all available in the supplied excerpts. The device is suitable when an embedded processor, microcontroller, FPGA, or Ethernet controller needs an Ethernet media-access solution without implementing analog PHY circuitry on the PCB. Its RMII interface can reduce host-side wiring compared with MII, while MII support provides compatibility with systems designed around parallel Ethernet control signals. The integrated 2.5 V core is relevant to low-voltage processor ecosystems and power-conscious embedded equipment. Typical applications include industrial Ethernet equipment, embedded gateways, set-top boxes, printers, game or media systems, network adapters, and control systems with 10/100BASE-T connectivity. Fiber-capable 100BASE-FX support can also suit equipment intended for longer-distance point-to-point links when the required optical partner and external implementation are present. When designing around KSZ8721BL, confirm the exact package variant and pinout against the manufacturer datasheet, preserve the required decoupling and media-interface layout, and verify the external magnetics or fiber components required by the selected network medium. The supplied data confirms the commercial temperature grade and 48-pin LQFP option, but does not establish RoHS, REACH, AEC-Q100, or halogen-free status. This product page consolidates the verified manufacturer description, technical identifiers, source links, and application guidance into an engineering-oriented reference for the KSZ8721BL Ethernet PHY.

RFQ Kontak
KSZ8721BL-TR - 100Mbps Ethernet PHY | Microchip | LQFP-48 (Tape & Reel)
KSZ8721BL-TR

KSZ8721BL-TR - 100Mbps Ethernet PHY | Microchip | LQFP-48 (Tape & Reel)

The Microchip KSZ8721BL-TR is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with MII and RMII host interfaces, operating at up to 100 Mbps in a 48-pin LQFP package. It supports a 2.5 V core for low-voltage and low-power operation, includes automatic MDI/MDI-X crossover, and is intended for embedded Ethernet designs requiring copper twisted-pair or fiber connections. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital MAC data into electrical or optical signaling suitable for a network medium and converts received signals back into digital data. The PHY sits between a host controller and the physical network medium, commonly using an MII or RMII interface. The KSZ8721BL-TR therefore belongs to the Ethernet interface hierarchy: transceiver, network interface controller companion, interface IC, and semiconductor. Key verified features include 100 Mbps operation, MII and RMII host-interface support, 10/100BASE-TX and 100BASE-FX capability, automatic MDI/MDI-X crossover, 3.3 V single-supply operation, and a 2.5 V core. The commercial temperature range is 0°C to +70°C. The reported supply current is 151 mA, while the exact pin mapping, package dimensions, transceiver electrical limits, and full timing values are not all available in the supplied excerpts. The device is suitable when an embedded processor, microcontroller, FPGA, or Ethernet controller needs an Ethernet media-access solution without implementing analog PHY circuitry on the PCB. Its RMII interface can reduce host-side wiring compared with MII, while MII support provides compatibility with systems designed around parallel Ethernet control signals. The integrated 2.5 V core is relevant to low-voltage processor ecosystems and power-conscious embedded equipment. Typical applications include industrial Ethernet equipment, embedded gateways, set-top boxes, printers, game or media systems, network adapters, and control systems with 10/100BASE-T connectivity. Fiber-capable 100BASE-FX support can also suit equipment intended for longer-distance point-to-point links when the required optical partner and external implementation are present. When designing around KSZ8721BL-TR, confirm the exact package variant and pinout against the manufacturer datasheet, preserve the required decoupling and media-interface layout, and verify the external magnetics or fiber components required by the selected network medium. The supplied data confirms the commercial temperature grade and 48-pin LQFP option, but does not establish RoHS, REACH, AEC-Q100, or halogen-free status. This product page consolidates the verified manufacturer description, technical identifiers, source links, and application guidance into an engineering-oriented reference for the KSZ8721BL-TR Ethernet PHY.

RFQ Kontak
KSZ8721BLI - 3.3V 10/100 Ethernet PHY | Microchip
KSZ8721BLI

KSZ8721BLI - 3.3V 10/100 Ethernet PHY | Microchip

Microchip KSZ8721BLI is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with full MII and RMII host interfaces, supplied in a 48-LQFP 7x7 mm package. The device operates at 10 Mbps and 100 Mbps and supports 10BASE-T copper, 100BASE-TX copper, and 100BASE-FX fiber media through integrated physical-layer functions. Its low-voltage 2.5 V to 3.3 V operating capability is intended to reduce system power while supporting 10BASE-T/100BASE-TX/FX network connections. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital frame data into electrical or optical signaling suitable for a network medium. In the hierarchy of network semiconductors, the PHY sits below the Ethernet controller or media-access controller and above the transformer, connector, or fiber interface. The KSZ8721BLI also provides an MDI/MDI-X auto-crossover function, allowing copper links to use a standard straight-through cable arrangement without manual crossover configuration. The KSZ8721BLI combines 10BASE-T and 100BASE-TX/FX support in one transceiver while offering both MII and RMII host connectivity. Full MII provides a parallel interface for legacy or higher-bandwidth controller arrangements, whereas RMII reduces the number of host-side signals and is useful in space-constrained embedded systems. The single 3.3 V supply architecture simplifies power design, although interface voltage compatibility must still be checked against the selected host controller. The device is positioned for industrial embedded networking, where a 10/100 Mbps copper or fiber link can be added without implementing the complete Ethernet data path in the host. Its industrial temperature option is identified by the KSZ8721 family documentation, which lists a -40°C to +85°C industrial range. Package construction is surface-mount LQFP, allowing conventional PCB assembly and inspection while requiring careful pin-1 orientation and solderability checks. Typical uses include industrial controllers, factory automation equipment, embedded gateways, serial-to-Ethernet systems, media converters, and compact network appliances. For copper links, designers must add the appropriate isolation transformer and RJ-05 or shielded-jack hardware. For fiber links, the external optical components and interface requirements should be implemented according to the manufacturer application guidance rather than inferred from the PHY package alone. The main design consideration is interface verification. Confirm that the host controller supports the selected MII or RMII mode, the transceiver’s supply voltage, and the external magnetics required by the target copper or fiber network. This page consolidates the verified source links, pricing observation, package information, replacement data, and engineering considerations into a practical procurement and design reference.

RFQ Kontak
KSZ8721BLI-TR - 3.3V 10/100 Ethernet PHY | Microchip (Tape & Reel)
KSZ8721BLI-TR

KSZ8721BLI-TR - 3.3V 10/100 Ethernet PHY | Microchip (Tape & Reel)

Microchip KSZ8721BLI-TR is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with full MII and RMII host interfaces, supplied in a 48-LQFP 7x7 mm package. The device operates at 10 Mbps and 100 Mbps and supports 10BASE-T copper, 100BASE-TX copper, and 100BASE-FX fiber media through integrated physical-layer functions. Its low-voltage 2.5 V to 3.3 V operating capability is intended to reduce system power while supporting 10BASE-T/100BASE-TX/FX network connections. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital frame data into electrical or optical signaling suitable for a network medium. In the hierarchy of network semiconductors, the PHY sits below the Ethernet controller or media-access controller and above the transformer, connector, or fiber interface. The KSZ8721BLI-TR also provides an MDI/MDI-X auto-crossover function, allowing copper links to use a standard straight-through cable arrangement without manual crossover configuration. The KSZ8721BLI-TR combines 10BASE-T and 100BASE-TX/FX support in one transceiver while offering both MII and RMII host connectivity. Full MII provides a parallel interface for legacy or higher-bandwidth controller arrangements, whereas RMII reduces the number of host-side signals and is useful in space-constrained embedded systems. The single 3.3 V supply architecture simplifies power design, although interface voltage compatibility must still be checked against the selected host controller. The device is positioned for industrial embedded networking, where a 10/100 Mbps copper or fiber link can be added without implementing the complete Ethernet data path in the host. Its industrial temperature option is identified by the KSZ8721 family documentation, which lists a -40°C to +85°C industrial range. Package construction is surface-mount LQFP, allowing conventional PCB assembly and inspection while requiring careful pin-1 orientation and solderability checks. Typical uses include industrial controllers, factory automation equipment, embedded gateways, serial-to-Ethernet systems, media converters, and compact network appliances. For copper links, designers must add the appropriate isolation transformer and RJ-05 or shielded-jack hardware. For fiber links, the external optical components and interface requirements should be implemented according to the manufacturer application guidance rather than inferred from the PHY package alone. The main design consideration is interface verification. Confirm that the host controller supports the selected MII or RMII mode, the transceiver’s supply voltage, and the external magnetics required by the target copper or fiber network. This page consolidates the verified source links, pricing observation, package information, replacement data, and engineering considerations into a practical procurement and design reference.

RFQ Kontak
KSZ8721BT - 10/100 Ethernet PHY Transceiver | Microchip
KSZ8721BT

KSZ8721BT - 10/100 Ethernet PHY Transceiver | Microchip

The Microchip Technology KSZ8721BT is a single-channel 10/100 Base-TX/FX Ethernet physical-layer transceiver operating from a 3.3 V single supply in a 48-pin TQFP package measuring 7 mm by 7 mm. According to the manufacturer product information, the device supports both MII and RMII host interfaces, 10BASE-T and 100BASE-TX copper links, and 100BASE-FX fiber links. Its core role is to connect a digital Ethernet host interface to an Ethernet medium through integrated PCS and PMA functions. An Ethernet PHY transceiver is an interface IC that converts parallel digital Ethernet data into physical signaling for copper or optical media, while receiving and decoding incoming signals. The KSZ8721 belongs to the PHY hierarchy: Ethernet interface IC, physical-layer transceiver, 10/100 Ethernet PHY, and network interface semiconductor. Supporting both copper and fiber media makes it useful in industrial control, embedded networking, communications equipment, and factory automation systems. Verified source information identifies the KSZ8721 as a 10BaseT/100BaseTX/FX physical-layer transceiver with MII and RMII host connectivity. The RMII option can reduce host pin requirements compared with a parallel MII arrangement, which is valuable when conserving connector and processor I/O resources. The 100BASE-FX capability supports fiber links where electrical copper reach or electromagnetic environments make optical media preferable. Exact PHY tolerances, clock requirements, link-distance targets, and electrical thresholds must be confirmed in the manufacturer datasheet before design release. The 48-TQFP surface-mount package is suitable for automated PCB assembly and compact multilayer boards. Its exact pin functions, exposed-pad arrangement, supply connections, and grounding requirements were not supplied in the verified excerpts, so they must not be inferred. Designers should preserve the manufacturer's recommended magnetics, termination network, RJ45 layout, fiber-isolation boundary, and high-speed trace topology. Decoupling and return paths are particularly important because Ethernet PHY performance depends on clean references and controlled common-mode behavior. Typical uses include 10/100 Ethernet links in embedded controllers, industrial Ethernet gateways, serial-to-Ethernet equipment, network switches, test instruments, and optical-to-copper media converters. The combination of MII, RMII, copper, and fiber support lets one device bridge several common legacy network-interface architectures. Exact suitability for a particular MAC, processor, transformer, optical module, or cable length must be verified against the complete datasheet and system timing requirements. This page consolidates the verified manufacturer, distributor, and datasheet-index information while clearly separating missing technical data. Its engineering value is the application guidance, sourcing context, and explicit compatibility boundaries rather than guessed specifications. Before purchasing or laying out a replacement board, verify lifecycle status, exact electrical limits, pinout, media support, and package details against the authoritative Microchip documentation. This page also distinguishes verified facts from open engineering questions. Because the excerpts do not supply a complete electrical table, package drawing, lifecycle statement, or pin-level map, each missing item is marked rather than estimated. That conservative approach is essential for Ethernet hardware, where an incorrect pin assignment, unsupported interface mode, or inappropriate power assumption can prevent link negotiation or damage a design.

RFQ Kontak
KSZ8721CL - 10/100 Ethernet PHY, MII, 48-LQFP | Microchip
KSZ8721CL

KSZ8721CL - 10/100 Ethernet PHY, MII, 48-LQFP | Microchip

The Microchip Technology KSZ8721CL is a single-port 10BASE-T, 100BASE-TX, and 100BASE-FX Ethernet physical-layer transceiver with MII and RMII host interfaces, a 3.3 V supply, and a 48-LQFP 7 x 7 mm package. The verified distributor information identifies one transmitter and one receiver, Full MII operation, and tray packaging. An Ethernet PHY is the physical-layer interface between a network MAC and copper or fiber cabling. It converts digital MAC data into electrical signaling for 10/100 Ethernet networks and receives incoming signals for recovery by the MAC. The KSZ8721 family therefore belongs to the Ethernet interface IC and physical-layer transceiver hierarchy, supporting 10BASE-T copper, 100BASE-TX copper, and 100BASE-FX optical-fiber links. The KSZ8721 supports 3.3 V single-supply operation and is described by Microchip as operating from 2.5 V to meet low-voltage and low-power requirements. Its mixed-signal design is intended to extend signaling distance while reducing power consumption. The available data confirms MII and RMII host-interface options, but individual MII clock rates, RMII timing limits, transceiver insertion loss, crossover support, and link-distance limits are not supplied here and require manufacturer-datasheet confirmation. Typical implementation roles include industrial Ethernet controllers, embedded network equipment, single-port Ethernet switches, print servers, and communication equipment. In an MII design, the PHY interfaces through parallel digital signals to a MAC or switch engine; in an RMII design, it uses the reduced pin-count interface specified by the host controller. The 48-LQFP package provides 48 external connections but requires careful high-speed signal layout. A key design consideration is that Ethernet PHY performance depends as much as the IC on magnetic-interface components, crystal timing, controlled-impedance PCB routing, supply bypassing, and isolation from noisy switching circuitry. Verify the exact transceiver mode, pin names, recommended magnetics, termination, and reference schematic against the current Microchip datasheet before layout release. This product data consolidates verified distributor availability, package information, interface capabilities, and technical-source links with application guidance and transparent data-gap markers. It is intended to accelerate sourcing and initial engineering review without replacing the manufacturer datasheet or schematic-level validation.

RFQ Kontak
KSZ8721CL-TR - 10/100 Ethernet PHY, MII, 48-LQFP | Microchip (Tape & Reel)
KSZ8721CL-TR

KSZ8721CL-TR - 10/100 Ethernet PHY, MII, 48-LQFP | Microchip (Tape & Reel)

The Microchip Technology KSZ8721CL-TR is a single-port 10BASE-T, 100BASE-TX, and 100BASE-FX Ethernet physical-layer transceiver with MII and RMII host interfaces, a 3.3 V supply, and a 48-LQFP 7 x 7 mm package. The verified distributor information identifies one transmitter and one receiver, Full MII operation, and tray packaging. An Ethernet PHY is the physical-layer interface between a network MAC and copper or fiber cabling. It converts digital MAC data into electrical signaling for 10/100 Ethernet networks and receives incoming signals for recovery by the MAC. The KSZ8721 family therefore belongs to the Ethernet interface IC and physical-layer transceiver hierarchy, supporting 10BASE-T copper, 100BASE-TX copper, and 100BASE-FX optical-fiber links. The KSZ8721 supports 3.3 V single-supply operation and is described by Microchip as operating from 2.5 V to meet low-voltage and low-power requirements. Its mixed-signal design is intended to extend signaling distance while reducing power consumption. The available data confirms MII and RMII host-interface options, but individual MII clock rates, RMII timing limits, transceiver insertion loss, crossover support, and link-distance limits are not supplied here and require manufacturer-datasheet confirmation. Typical implementation roles include industrial Ethernet controllers, embedded network equipment, single-port Ethernet switches, print servers, and communication equipment. In an MII design, the PHY interfaces through parallel digital signals to a MAC or switch engine; in an RMII design, it uses the reduced pin-count interface specified by the host controller. The 48-LQFP package provides 48 external connections but requires careful high-speed signal layout. A key design consideration is that Ethernet PHY performance depends as much as the IC on magnetic-interface components, crystal timing, controlled-impedance PCB routing, supply bypassing, and isolation from noisy switching circuitry. Verify the exact transceiver mode, pin names, recommended magnetics, termination, and reference schematic against the current Microchip datasheet before layout release. This product data consolidates verified distributor availability, package information, interface capabilities, and technical-source links with application guidance and transparent data-gap markers. It is intended to accelerate sourcing and initial engineering review without replacing the manufacturer datasheet or schematic-level validation.

RFQ Kontak
KSZ8721SL - 10/100 Ethernet PHY | Microchip Technology
KSZ8721SL

KSZ8721SL - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8721SL is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with MII and RMII host interfaces, supplied in a 48-pin SSOP package. It supports 10 Mb/s and 100 Mb/s Ethernet links and is identified as a full IEEE 802.3 transceiver for industrial and embedded Ethernet designs. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, is the circuit that connects a digital Ethernet controller to a twisted-pair or fiber medium. The PHY belongs to the network-interface IC hierarchy and combines functions such as physical-medium attachment, physical-medium-dependent circuitry, and physical coding sub-layer operation. The KSZ8721SL translates frames between the parallel MII or RMII interface of a host controller and encoded Ethernet signals on the network medium. The principal verified specifications for the KSZ8721SL include a 3.3 V operating supply, support for both 10BASE-T and 100BASE-TX operation, additional 100BASE-FX capability, MII and RMII host interfaces, an IEEE 802.3-compliant transceiver configuration, and a 48-pin SSOP surface-mount package. Its commercial operating-temperature range is 0 °C to +70 °C. The SMD package supports compact embedded systems while exposing separate network and host-interface functions. The MII interface supports a parallel Ethernet controller connection, while RMII reduces the number of host-interface signals compared with MII. This makes the RMII connection useful when the selected Ethernet MAC requires a compact serial control and data interface. The fiber-capable 100BASE-FX feature also allows the same physical-layer family to address copper and fiber link requirements, subject to the external optical and isolation circuitry required by the specific design. Typical uses include industrial Ethernet equipment, embedded control systems, network adapters, print servers, factory automation equipment, and communications products requiring 10 Mb/s or 100 Mb/s Ethernet. Designers should confirm whether the selected board uses copper, fiber, or both media and should validate the required transformers, isolation components, magnetic-interface layout, termination, and host-interface timing against the manufacturer datasheet. The principal design consideration is that the KSZ8721SL is a commercial-temperature, 48-pin SSOP device rather than an industrial-temperature substitute. Layout should provide a continuous ground reference, short supply connections, controlled-length differential copper routing, and compliant separation between network-side and host-side circuitry where applicable. Its 3.3 V single-supply operation also requires the host interface, clocking, and external network components to be compatible with the implemented interface topology. This page combines the verified manufacturer and distributor information with package, sourcing, design, and replacement guidance intended to reduce common selection errors. It distinguishes confirmed drop-in options from unreferenced parts and leaves unavailable electrical, pricing, and pin-level details explicitly marked rather than estimating them.

RFQ Kontak
KSZ8721SL-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)
KSZ8721SL-TR

KSZ8721SL-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)

The Microchip Technology KSZ8721SL-TR is a 3.3 V single-supply 10/100BASE-TX/FX Ethernet physical-layer transceiver with MII and RMII host interfaces, supplied in a 48-pin SSOP package. It supports 10 Mb/s and 100 Mb/s Ethernet links and is identified as a full IEEE 802.3 transceiver for industrial and embedded Ethernet designs. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, is the circuit that connects a digital Ethernet controller to a twisted-pair or fiber medium. The PHY belongs to the network-interface IC hierarchy and combines functions such as physical-medium attachment, physical-medium-dependent circuitry, and physical coding sub-layer operation. The KSZ8721SL-TR translates frames between the parallel MII or RMII interface of a host controller and encoded Ethernet signals on the network medium. The principal verified specifications for the KSZ8721SL-TR include a 3.3 V operating supply, support for both 10BASE-T and 100BASE-TX operation, additional 100BASE-FX capability, MII and RMII host interfaces, an IEEE 802.3-compliant transceiver configuration, and a 48-pin SSOP surface-mount package. Its commercial operating-temperature range is 0 °C to +70 °C. The SMD package supports compact embedded systems while exposing separate network and host-interface functions. The MII interface supports a parallel Ethernet controller connection, while RMII reduces the number of host-interface signals compared with MII. This makes the RMII connection useful when the selected Ethernet MAC requires a compact serial control and data interface. The fiber-capable 100BASE-FX feature also allows the same physical-layer family to address copper and fiber link requirements, subject to the external optical and isolation circuitry required by the specific design. Typical uses include industrial Ethernet equipment, embedded control systems, network adapters, print servers, factory automation equipment, and communications products requiring 10 Mb/s or 100 Mb/s Ethernet. Designers should confirm whether the selected board uses copper, fiber, or both media and should validate the required transformers, isolation components, magnetic-interface layout, termination, and host-interface timing against the manufacturer datasheet. The principal design consideration is that the KSZ8721SL-TR is a commercial-temperature, 48-pin SSOP device rather than an industrial-temperature substitute. Layout should provide a continuous ground reference, short supply connections, controlled-length differential copper routing, and compliant separation between network-side and host-side circuitry where applicable. Its 3.3 V single-supply operation also requires the host interface, clocking, and external network components to be compatible with the implemented interface topology. This page combines the verified manufacturer and distributor information with package, sourcing, design, and replacement guidance intended to reduce common selection errors. It distinguishes confirmed drop-in options from unreferenced parts and leaves unavailable electrical, pricing, and pin-level details explicitly marked rather than estimating them.

RFQ Kontak
KSZ8721SLI - 10/100 Ethernet PHY | Microchip Technology
KSZ8721SLI

KSZ8721SLI - 10/100 Ethernet PHY | Microchip Technology

Microchip Technology KSZ8721SLI is a single-channel 10/100 Ethernet physical-layer transceiver with a 48-SSOP package, operating from a 2.5 V core and supporting a 3.3 V single-supply application. It provides separate 10Base-T and 100Base-TX/FX physical-medium functions plus MII and RMII host interfaces for transmitting and receiving Ethernet data. The device supports 10 Mbps and 100 Mbps operation and is intended for embedded networking equipment requiring a dedicated Ethernet PHY. An Ethernet physical-layer transceiver, or Ethernet PHY, converts logical digital data into electrical signaling for a physical network medium. The KSZ8721SLI belongs to the integrated-circuit hierarchy physical-layer transceiver > Ethernet interface IC > interface IC. Its 10Base-T capability supports legacy 10 Mbps copper Ethernet, while 100Base-TX/FX supports Fast Ethernet over twisted pair or optical-fiber-compatible links. The MII and RMII interfaces allow a host processor or network controller to connect through either a parallel media-independent interface or the more pin-efficient reduced media-independent interface. Key verified features include full IEEE 802.3 operation, support for 10Base-T, 100Base-TX, and 100Base-FX physical media, and both MII and RMII host connectivity. The KSZ8721 operates its core at 2.5 V to address low-voltage and low-power requirements, while the device is described as a 3.3 V single-supply transceiver. Its 48-SSOP package provides enough pins for separate transmit, receive, management, clock, and host-interface functions. Technically, the KSZ8721SLI consolidates a 10Base-T physical medium attachment function, a 100Base-TX/FX physical medium attachment function, and the associated host-facing digital interface into one package. MII exposes a wider parallel bus, while RMII reduces the number of host-interface signals and is commonly preferred when the connected controller supports it. The manufacturer identifies the KSZ8721 family as a 10BaseT, 100BaseTX, and FX physical-layer transceiver designed for low-power embedded networking. Typical uses include industrial Ethernet controllers, embedded gateways, set-top equipment, printer and scanner interfaces, test equipment, and OEM network appliances. A board designer can connect the KSZ8721SLI to an Ethernet transformer or appropriate fiber interface, provide the required decoupling, and connect it to an MII- or RMII-capable controller. The choice of media interface and magnetics should be based on the required copper or fiber link distance and system compliance targets. A critical design consideration is confirming the controller's MII or RMII timing, clock requirements, reset behavior, and supported media type against the manufacturer datasheet before layout release. Input and output supply rails should be decoupled close to the device, while the copper or fiber network path should be routed according to the selected magnetics and medium requirements. Do not infer unverified pin assignments or timing values from distributor listings alone. This page consolidates verified manufacturer and distributor information, package details, commercially relevant sourcing links, and same-family replacement evidence. It also provides application guidance and comparison context intended to support faster component selection without treating unreported electrical parameters as verified facts.

RFQ Kontak
KSZ8721SLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)
KSZ8721SLI-TR

KSZ8721SLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)

Microchip Technology KSZ8721SLI-TR is a single-channel 10/100 Ethernet physical-layer transceiver with a 48-SSOP package, operating from a 2.5 V core and supporting a 3.3 V single-supply application. It provides separate 10Base-T and 100Base-TX/FX physical-medium functions plus MII and RMII host interfaces for transmitting and receiving Ethernet data. The device supports 10 Mbps and 100 Mbps operation and is intended for embedded networking equipment requiring a dedicated Ethernet PHY. An Ethernet physical-layer transceiver, or Ethernet PHY, converts logical digital data into electrical signaling for a physical network medium. The KSZ8721SLI-TR belongs to the integrated-circuit hierarchy physical-layer transceiver > Ethernet interface IC > interface IC. Its 10Base-T capability supports legacy 10 Mbps copper Ethernet, while 100Base-TX/FX supports Fast Ethernet over twisted pair or optical-fiber-compatible links. The MII and RMII interfaces allow a host processor or network controller to connect through either a parallel media-independent interface or the more pin-efficient reduced media-independent interface. Key verified features include full IEEE 802.3 operation, support for 10Base-T, 100Base-TX, and 100Base-FX physical media, and both MII and RMII host connectivity. The KSZ8721 operates its core at 2.5 V to address low-voltage and low-power requirements, while the device is described as a 3.3 V single-supply transceiver. Its 48-SSOP package provides enough pins for separate transmit, receive, management, clock, and host-interface functions. Technically, the KSZ8721SLI-TR consolidates a 10Base-T physical medium attachment function, a 100Base-TX/FX physical medium attachment function, and the associated host-facing digital interface into one package. MII exposes a wider parallel bus, while RMII reduces the number of host-interface signals and is commonly preferred when the connected controller supports it. The manufacturer identifies the KSZ8721 family as a 10BaseT, 100BaseTX, and FX physical-layer transceiver designed for low-power embedded networking. Typical uses include industrial Ethernet controllers, embedded gateways, set-top equipment, printer and scanner interfaces, test equipment, and OEM network appliances. A board designer can connect the KSZ8721SLI-TR to an Ethernet transformer or appropriate fiber interface, provide the required decoupling, and connect it to an MII- or RMII-capable controller. The choice of media interface and magnetics should be based on the required copper or fiber link distance and system compliance targets. A critical design consideration is confirming the controller's MII or RMII timing, clock requirements, reset behavior, and supported media type against the manufacturer datasheet before layout release. Input and output supply rails should be decoupled close to the device, while the copper or fiber network path should be routed according to the selected magnetics and medium requirements. Do not infer unverified pin assignments or timing values from distributor listings alone. This page consolidates verified manufacturer and distributor information, package details, commercially relevant sourcing links, and same-family replacement evidence. It also provides application guidance and comparison context intended to support faster component selection without treating unreported electrical parameters as verified facts.

RFQ Kontak
KSZ8765CLXCC - 5-Port Managed Ethernet Switch | Microchip
KSZ8765CLXCC

KSZ8765CLXCC - 5-Port Managed Ethernet Switch | Microchip

Microchip Technology KSZ8765CLXCC is an integrated Layer 2-managed Ethernet switch with four 10/100 Mbps copper ports, one 10/100/1000 Mbps Gigabit uplink, and fiber support in an 80-pin LQFP package measuring 10 x 10 mm. It supports GMII, RGMII, MII, and RMII interfaces, allowing flexible connection to network processors, switching fabrics, and embedded Ethernet equipment. An Ethernet switch is a semiconductor that forwards Ethernet frames between multiple physical ports while reducing the need for separate switching hardware on each link. The KSZ8765 belongs to the managed-switch hierarchy: Ethernet switch, Layer 2 network switch, interface IC, and integrated circuit. Its five-port arrangement combines copper Ethernet connectivity with a gigabit uplink, making it suitable for compact embedded network infrastructure where board area and interface flexibility are important. The primary features include four 10/100 Mbps copper ports, one Gigabit port, integrated 10/100 Base-FX/T/TX PHY support, and both legacy MII/RMII and gigabit GMII/RGMII interfaces. Layer 2 management adds value in access equipment, industrial controls, network appliances, and test systems where individual port configuration, traffic prioritization, or centralized switching behavior can simplify firmware and board design. The combination of MII, RMII, GMII, and RGMII support distinguishes the KSZ8765 from simpler unmanaged Ethernet switches. A host processor can connect through RMII or MII for 10/100 Mbps designs, while GMII or RGMII supports a Gigabit data path. This range of host interfaces permits one switch platform to address multiple processor architectures and clocking arrangements without changing the external Ethernet-port topology. Typical uses include industrial Ethernet gateways, embedded network appliances, communication equipment, test and measurement systems, and access-control infrastructure. The four copper ports support device-to-device links, while the Gigabit port can provide a higher-bandwidth uplink to a router, control processor, or backplane. Fiber-capable operation is useful where longer-distance links or galvanic-isolation requirements make copper unsuitable. PCB design must account for the 10 x 10 mm LQFP footprint, high-speed interface constraints, proper decoupling, and controlled impedance routing for GMII and RGMII links. Review the Microchip reference design and pin-description table to assign power, ground, clocks, management signals, and PHY connections before releasing the layout. This page combines the Microchip product definition, package and interface information, application guidance, and same-family drop-in alternatives. It also highlights the design decisions that matter when moving between temperature-grade variants of the KSZ8765 while retaining the same 80-pin LQFP footprint.

RFQ Kontak
KSZ8765CLXIC - 5-Port Managed Ethernet Switch | Microchip
KSZ8765CLXIC

KSZ8765CLXIC - 5-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8765CLXIC is a highly integrated, Layer 2-managed, five-port Ethernet switch for embedded networking systems. It combines four 10/100 Mbps copper ports with one 10/100/1000 Mbps Gigabit uplink, supports 100Base-FX fiber connectivity, and provides configurable GMII, RGMII, MII, and RMII host interfaces. The device is packaged in an 80-lead LQFP measuring 10 mm by 10 mm. An Ethernet switch is a Layer 2 network-semiconductor device that receives Ethernet frames on one port, examines their destination addresses, and forwards traffic to the appropriate port or ports. A managed switch adds configurable status, control, and monitoring functions to this basic forwarding role. The KSZ8765 belongs to the broader hierarchy of Ethernet switch, network interface controller, communications semiconductor, and integrated circuit. Key features include five integrated switch ports, Layer 2 management, 10/100 Mbps copper networking, a Gigabit uplink, and support for both fiber and copper media. Its configurable GMII, RGMII, MII, and RMII interfaces allow it to connect with microcontrollers, network processors, FPGAs, and other Ethernet-capable system controllers. The hardware design checklist identifies Ports 1 and 2 as 100Base-FX fiber ports, Ports 3 and 4 as 10/100Base-T/TX copper ports, and Port 5 as a configurable uplink supporting GMII, RGMII, MII, or RMII. The KSZ8765CLXIC is designed to reduce the component count of embedded Ethernet equipment by combining multiple physical-layer interfaces, switching logic, and management functions in one package. This integration can simplify board partitioning while preserving separate copper and fiber connectivity. Its architecture is particularly useful when an equipment maker needs a managed industrial network interface without implementing five discrete Ethernet PHYs and an external switch controller. Typical uses include industrial Ethernet equipment, factory automation controllers, embedded gateways, telecom access hardware, network appliances, and optical-to-copper network bridges. The device can support equipment that bridges legacy 10/100 Mbps copper links to a faster Gigabit uplink while retaining access to optical ports for longer-distance or electrically isolated links. Designers should follow the Microchip KSZ8765CLX Hardware Design Checklist when assigning the clock, management interface, media-dependent interfaces, power rails, and reset or configuration signals. The complete electrical limits, recommended operating conditions, transceiver details, internal register functions, and signal timing must be taken from the manufacturer datasheet rather than inferred from the product summary. This page combines the manufacturer product description, package and interface facts, pricing-page information, and hardware-design guidance into an application-focused guide. It also distinguishes directly documented characteristics from electrical parameters that require confirmation from the complete KSZ8765 datasheet.

RFQ Kontak