Mga Produkto (46,000+)

KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip
KSZ8794CNXIC

KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8794CNXIC is a highly integrated, Layer 2 managed Ethernet switch with three 10/100 Mbps copper ports and one 10/100/1000 Mbps uplink port, housed in a 64-QFN 8 mm by 8 mm package. Its configurable RGMII, MII, and RMII uplink interface supports flexible host connections while the four-port architecture combines copper-port switching with a Gigabit uplink. An Ethernet switch is a semiconductor that connects multiple network endpoints through one uplink to a host, router, or wider network. The managed designation means the KSZ8794 provides Layer 2 switch functions rather than operating only as a basic repeater or hub. Within the networking hierarchy, it combines Ethernet switching, a 10/100BASE-T/TX PHY for copper ports, and a configurable Gigabit serial interface for the uplink. The KSZ8794CNX is intended for cost-sensitive systems requiring three 10/100 Mbps copper ports and one Gigabit uplink. Its integrated design reduces the number of discrete network components required in industrial controllers, residential gateways, embedded equipment, and network appliances. Microchip identifies internal biasing, low power consumption, on-chip termination, and a small package outline as major cost and design benefits. The uplink can operate with RGMII, MII, or RMII, allowing system architects to match the switch to processors, FPGAs, and other Ethernet-capable controllers according to timing, pin-count, and design-complexity requirements. This flexibility is particularly useful when one platform must support several host interfaces or when a product family needs to reuse related switch designs. Typical implementation places the KSZ8794CNX between three copper-connected devices and a higher-speed network uplink. In an industrial controller, the copper ports can connect local sensors, service interfaces, or production equipment while the uplink carries aggregated traffic. In a residential gateway, the same arrangement supports three local Ethernet endpoints and a Gigabit connection to an access network or router. Hardware implementation should follow the KSZ8794CNX Hardware Design Checklist, including guidance on magnetics, termination, layout, and interface implementation. The device also has an associated silicon errata and data-sheet clarification document, so production designs should account for the applicable silicon revision and current manufacturer documentation. This page consolidates the verified switch architecture, interface options, package information, hardware-design guidance, errata context, and sourcing details into an engineering-focused overview. It also identifies which detailed electrical, timing, environmental, and pin-level values require confirmation from the current manufacturer datasheet before schematic release or PCB signoff.

RFQ Kontak
KSZ8795CLXCC - 5-Port Managed Ethernet Switch | Microchip
KSZ8795CLXCC

KSZ8795CLXCC - 5-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8795CLXCC is a highly integrated, Layer 2-managed five-port Ethernet switch with four 10/100 Mbps copper ports and one 10/100/1000 Mbps Gigabit uplink port, housed in an 80-lead LQFP package measuring 10 mm by 10 mm. The device combines copper-port switching with Gigabit uplink connectivity for cost-sensitive embedded networking systems. An Ethernet switch is a semiconductor that connects multiple physical-layer network ports to a common switching fabric and forwards Ethernet frames between ports and an uplink processor. The KSZ8795 operates at the Layer 2 data-link level, where frame destination addresses determine the outgoing port. Its managed architecture provides a practical platform for connected industrial, consumer, communications, and embedded equipment requiring several copper Ethernet connections. The KSZ8795's principal features are its four dedicated 10/100 Mbps copper ports, dedicated 10/100/1000 Mbps uplink capability, and support for GMII/RGMII and MII/RMII processor interfaces. These parallel interface options let the switch connect to controllers with different clocking and data-width requirements. Layer 2 management supports controlled network behavior rather than operating solely as an unmanaged frame-forwarding device. The KSZ8795CLXCC is packaged in an 80-lead LQFP, identified by the CLX package code in the manufacturer ordering information. Its 10 mm by 10 mm surface-mount package consolidates five-port switching, a Gigabit uplink, and management functions into one device. The exact pin names, voltage limits, timing limits, clock requirements, and electrical characteristics should be taken from the manufacturer datasheet and hardware design checklist when assigning PCB signals. Typical implementations include industrial Ethernet gateways, IP cameras, building-automation controllers, communications equipment, set-top and media systems, and embedded products that expose several 10/100 ports while retaining a Gigabit connection to a host processor. The four fast ports support legacy 10/100 equipment, while the Gigabit uplink supports higher-bandwidth backhaul or processor traffic. MII, RMII, GMII, and RGMII connectivity allows the switch to be adapted to different embedded Ethernet controller arrangements. PCB implementation requires careful separation of high-speed digital interfaces from copper-port circuitry. Place the KSZ8795CLX hardware design checklist alongside the datasheet, use the recommended magnetic-interface and termination network for each copper port, and observe the package's exposed-pad and thermal-land requirements. The manufacturer checklist specifies RJ45 transmit routing and a 75 ohm, 1000 pF, 2 kV capacitor network for the cable-side center tap, making those details important during layout review. This page organizes the switch's port architecture, interface options, package information, sourcing workflow, and design references into an engineering-focused selection guide. It also identifies why the exact KSZ8795CLXCC ordering code must be reviewed against schematic, PCB, thermal, and firmware requirements rather than substituted solely by port count or headline uplink speed.

RFQ Kontak
KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip
KSZ8795CLXIC

KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8795CLXIC is a Layer 2 managed, highly integrated 5-port Ethernet switch with four 10/100BASE-T/TX copper ports and one 10/100/1000BASE-T Gigabit uplink port, delivering configurable GMII, RGMII, MII and RMII host interfaces from an 80-LQFP (10 x 10 mm) package. It operates from a single 3.3 V supply and is offered in an industrial-temperature ordering code. An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between multiple physical ports using a MAC address table. In this device family, the switch also integrates 10/100BASE-T/TX PHYs with internal biasing resistors, on-chip termination and auto-negotiation, so a single silicon device replaces discrete magnetics-heavy copper PHY circuitry. The KSZ8795CLXIC therefore sits in the hierarchy: Ethernet switch > Layer 2 managed switch > integrated copper PHY switch > network interface IC. Key features include four 10/100Mbps copper ports with auto-MDIX support, a Gigabit-capable uplink port, IEEE 802.3u compliant operation, MIIM and SPI management interfaces, and on-chip port termination that eliminates external resistor networks. Low power consumption is achieved through internal biasing rather than external resistor dividers, and the small package outline reduces board area versus discrete implementations. Internally the device combines a five-port frame buffer with an integrated 10/100 MAC/PHY per copper port and a configurable uplink MAC supporting GMII, RGMII, MII and RMII. Management is handled by a MIIM register interface and an SPI host interface, giving the system processor access to VLAN, QoS, port enable and mirror registers. The design is intended for cost-sensitive embedded equipment where a single high-integration switch replaces several discrete PHYs and magnetics. Typical applications include industrial control gateways, industrial Ethernet switches and PLC communication modules, IP cameras and surveillance recorders, industrial IoT and building-automation nodes, and consumer or telecom CPE equipment with a Gigabit uplink. The configurable uplink lets one design serve either RGMII-based application processors or RMII-based microcontrollers. Keep the analog and digital ground pins tied to a single solid, contiguous ground plane. Microchip explicitly warns that splitting GDNA and GNDD into separate planes causes frame drops, so route both to the same uninterrupted system ground and place the port magnetics with short, tightly-coupled differential pairs to preserve return-path integrity. This page combines the manufacturer switch specifications, distributory pricing structure, pin-compatible 80-LQFP alternatives, and practical layout and thermal guidance that you would otherwise have to reconstruct from several separate documents.

RFQ Kontak
KSZ8841-16MBLI - 10/100 Ethernet MAC/PHY | Microchip
KSZ8841-16MBLI

KSZ8841-16MBLI - 10/100 Ethernet MAC/PHY | Microchip

The Microchip Technology KSZ8841-16MBLI is a single-port 10/100 Mb/s Ethernet controller with an integrated MAC and 10BASE-T/100BASE-TX PHY, supplied in a 3.3 V, 100-pin LFBGA package. It provides a generic 8-bit or 16-bit non-PCI host processor interface and supports the Ethernet functions required by embedded systems that need a compact network connection. An Ethernet MAC controller is the protocol-processing portion of an Ethernet interface. It manages frame transmission and reception, while an Ethernet PHY connects the digital controller to the physical network medium. By integrating the MAC and PHY, the KSZ8841-16MBLI reduces the number of separate network components required in embedded networking equipment. It belongs to the hierarchy of Ethernet controller, network interface controller, interface IC, and semiconductor. The controller supports 10 Mb/s and 100 Mb/s operation, uses a 3.3 V supply, and includes Wake-on-LAN technology for Fast Ethernet applications. Its generic host interface can operate with an 8-bit or 16-bit processor bus. The device also uses a dynamic memory pointer with 4-byte buffer boundaries, helping the host software organize packet-buffer access while preserving compatibility with embedded CPU architectures. As a mixed-signal device, the KSZ8841-16MBLI combines digital packet-processing logic with the analog circuitry required by the integrated Ethernet PHY. This integration supports a compact board layout, but the high-speed and analog sections still require careful printed-circuit-board planning. Suitable implementation details include controlled impedance routing for the Ethernet conductors, solid supply decoupling, and a short, controlled connection between the controller and its magnetic interface. Typical applications include embedded industrial controllers, network management equipment, print servers, set-top and access systems, single-port routers, and other embedded products that require Fast Ethernet connectivity. It is also appropriate when a host processor needs direct access to the Ethernet MAC through a generic parallel bus rather than a PCI interface. Designers should select magnetic-interface and termination components according to the reference circuitry in the manufacturer datasheet. The 100-pin LFBGA also requires a PCB land pattern capable of supporting its pitch and thermal requirements. Pin assignments, exposed-pad treatment, and package dimensions should be taken directly from the package drawing rather than inferred from a generic BGA footprint. This product page consolidates the confirmed controller functions, package information, sourcing workflow, and engineering guidance into one reference. It also distinguishes the exact industrial-temperature ordering code from related interface options and records where package-level verification remains essential before board release.

RFQ Kontak
KSZ8841-16MVLI - 10/100 Ethernet Controller | Microchip
KSZ8841-16MVLI

KSZ8841-16MVLI - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8841-16MVLI is a single-port 10/100 Base-T/TX Ethernet MAC controller with an integrated Fast Ethernet PHY and a generic 16-bit host processor interface. It supports one Ethernet port at 100 Mb/s, uses a 128-lead LQFP package measuring 14 x 14 mm, and includes Wake-on-LAN functionality for remotely waking compatible systems. An Ethernet MAC controller is a network interface integrated circuit that manages frame transmission, reception, addressing, and the connection between a host processor and an Ethernet physical layer. The KSZ8841 belongs to the Ethernet controller hierarchy, which combines a MAC controller, 10/100 Base-T/TX PHY, and a generic host-bus interface in a single mixed-signal device. This integration reduces external components and simplifies the relationship between the processor bus and an RJ45 network connection. The KSZ8841 supports 8-bit, 16-bit, and 32-bit generic host-processor interfaces. The -16MVLI configuration uses a 16-bit interface, while its dynamic memory pointer maintains a 4-byte buffer boundary for host-memory transfers. A dedicated integrated PHY provides 10/100 Base-T/TX operation, while Wake-on-LAN support addresses power-conscious embedded systems that must respond to remote network activity. The controller combines digital frame-processing logic with analog Ethernet transceiver circuitry. Its host interface provides a direct path between the Ethernet MAC and processor-managed memory, reducing the need for a separate Ethernet interface component. In systems requiring wider bus bandwidth, the related 32-bit controller option can move data in wider transactions, although the exact memory-transfer rate still depends on processor timing, wait states, and the physical interface implementation. Typical uses include industrial embedded controllers, factory automation equipment, print servers, set-top boxes, embedded servers, and network-enabled data-acquisition systems. In an industrial controller, the device can connect an embedded processor to a 10/100 network while supporting remote wake-up for maintenance systems. In compact embedded products, integrating the PHY and MAC into one package reduces board area compared with a discrete MAC and external transceiver arrangement. PCB design should preserve the Ethernet magnetics and high-speed signal path, provide the decoupling and grounding specified by the manufacturer datasheet, and keep the processor-bus traces short. The 128-LQFP footprint requires careful escape routing because the generic host interface uses many pins. Confirm the complete pin assignment, voltage requirements, clocking, and reset behavior against the manufacturer pin-description table before routing the board. This product page combines the manufacturer interface description, verified ordering information, package details, and practical selection guidance. It also organizes pin, replacement, application, and sourcing questions around the distinctions that matter when integrating this Ethernet controller into a new embedded design.

RFQ Kontak
KSZ8841-32MVLI - 10/100 Ethernet Controller | Microchip
KSZ8841-32MVLI

KSZ8841-32MVLI - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8841-32MVLI is a single-port Ethernet MAC controller with an integrated 10/100 Base-T/TX PHY and a generic 32-bit host-bus interface, housed in a 128-LQFP 14 x 14 mm package. It combines Ethernet media-access control, physical-layer signaling, and host-interface functions in one integrated circuit for compact industrial networking equipment. An Ethernet MAC controller is an interface IC that manages frame transmission and reception between a processor and an Ethernet network. The associated PHY converts between digital Ethernet symbols and signals carried by twisted-pair cabling. Together, a MAC controller and PHY form the hardware boundary between a digital embedded system and a 10/100 Base-T network, reducing the number of discrete components required for an Ethernet port. The KSZ8841-32MVLI provides a generic 32-bit bus interface rather than the PCI interface used by the PCI version of the KSZ8841 family. This makes it suitable for embedded processors, industrial controllers, and other systems that can connect through a parallel host bus. Its integrated 10/100 Base-T/TX PHY supports connection to standard 10/100 Ethernet networks through the appropriate magnetics and external circuit implementation described by the manufacturer. The device is offered in a 128-LQFP package measuring 14 x 14 mm, providing many external signal connections for host-bus control, data, clocks, interrupts, power, and Ethernet physical-layer functions. The manufacturer classifies the KSZ8841 series as a family of single-port controllers with both PCI and non-PCI CPU-interface options. The 32MVLI ordering code identifies the non-PCI, generic 32-bit-interface configuration. Typical uses include industrial Ethernet gateways, embedded control systems, programmable logic controller communications, instrumentation equipment, and compact network adapters. The integrated MAC/PHY architecture simplifies the hardware and software boundary for a connected embedded product, while the parallel host interface provides a direct path between the Ethernet engine and a microprocessor or other bus master. Designers should follow the manufacturer reference design when assigning the generic host-bus signals, supplying the required clocks and decoupling, and implementing the Ethernet magnetics and analog network interface. Clock timing, signal-integrity practices, and controlled board layout are particularly important because the LQFP exposes numerous high-speed digital and Ethernet-related connections. This product overview consolidates the verified device classification, interface configuration, package information, sourcing data, comparison points, and implementation guidance. It also distinguishes genuine same-footprint alternatives from related parts with different bus widths so engineers can evaluate PCB reuse without relying on family-name similarity alone.

RFQ Kontak
KSZ8841-PMQL - 10/100 Ethernet PCI Controller | Microchip
KSZ8841-PMQL

KSZ8841-PMQL - 10/100 Ethernet PCI Controller | Microchip

The Microchip Technology KSZ8841-PMQL is a single-port Fast Ethernet MAC controller with a 32-bit, 33 MHz PCI processor interface, supplied in a 128-pin PQFP package measuring 14 x 20 mm. It combines an IEEE 802.3u-compatible 10/100 Base-T/TX Ethernet controller with a host-bus interface intended for PCI-based embedded systems. The controller integrates the Ethernet MAC function with the physical-layer interface needed for a single 10/100 network port. An Ethernet MAC controller is an interface integrated circuit that manages frame transmission and reception between a computing host and an Ethernet network. The MAC layer identifies network frames and handles access to the communications medium, while the integrated Fast Ethernet physical interface connects that logical function to twisted-pair cabling. In the system hierarchy, the KSZ8841-PMQL belongs to the class of Ethernet interface controllers and network interface integrated circuits used within embedded networking equipment. The KSZ8841-PMQL provides one 10/100 Base-T/TX port, a 32-bit PCI interface, and a stated PCI operating frequency of 33 MHz. Its IEEE 802.3u compatibility identifies the intended Fast Ethernet protocol generation. The device is also associated with a non-PCI member of the KSZ8841 series, KSZ8841-MQL, which uses a different CPU interface and therefore requires a different host-side design rather than being a universal substitute. The PCI host interface provides a parallel processor-facing path for moving Ethernet frames between the controller and an embedded PCI system. This makes the device appropriate for legacy or industrial embedded platforms that retain PCI infrastructure but require an integrated 10/100 Ethernet connection. The 128-PQFP package also provides a substantial pin count for the MAC, PCI, clock, reset, power, and physical-network functions represented by this controller. Typical applications for the KSZ8841-PMQL include PCI-based industrial controllers, embedded communication equipment, network interface adapters, and legacy embedded systems requiring 10/100 Base-T/TX connectivity. The controller can also serve as the foundation for custom PCI network-interface subsystems where a dedicated Ethernet MAC is required instead of a higher-complexity system-on-chip. Designers should distinguish the standard KSZ8841-PMQL from the industrial-temperature KSZ8841-PMQLI version when selecting the correct ordering code. PCB implementation must follow the manufacturer's 128-pin PQFP pinout and recommended layout guidance, including correct termination, clocking, reset sequencing, and Ethernet physical-layer routing. This product page combines the manufacturer identification, package information, interface details, comparison candidates, and application guidance needed to evaluate the KSZ8841-PMQL. Request a Quote on this page for current commercial availability, lead time, and supporting documentation.

RFQ Kontak
KSZ8842-16MBLI - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-16MBLI

KSZ8842-16MBLI - 2-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8842-16MBLI is a two-port 10/100 Ethernet switch with a generic 8-bit or 16-bit parallel CPU interface, supplied in a 100-LFBGA package. It integrates two Fast Ethernet switch ports with a non-PCI host interface for embedded networking designs. An Ethernet switch is a network-semiconductor device that connects multiple Ethernet nodes through a common switching engine. In the broader hierarchy, the KSZ8842-16MBLI belongs to Ethernet interface controllers, then network interface ICs, interface ICs, and integrated circuits. Unlike a physical-layer-only Ethernet transceiver, this device includes the switching function required to interconnect two 10/100 Ethernet ports. The KSZ8842-16MBLI is identified as a two-port 10/100 Base-T/TX PHY switch with a parallel interface. Its 8/16-bit bus architecture allows an embedded processor or controller to access registers and status information through a non-PCI interface. This makes it suitable for systems that need two Ethernet ports but do not require a PCI bus controller. Microchip organizes the KSZ8842 family into PCI and non-PCI CPU-interface versions, with 8/16-bit and 32-bit bus designs available across the family. The “16” designation in KSZ8842-16MBLI identifies the 8/16-bit non-PCI family segment, while “MBL” identifies the 100-LFBGA package option used by this ordering code. Typical applications include embedded routers, industrial control gateways, industrial automation equipment, networked sensors, set-top equipment, and compact communications controllers. In each case, the two integrated 10/100 ports reduce the need for separate Ethernet switching components while preserving a processor-friendly parallel management interface. For PCB implementation, treat the 100-LFBGA land pattern and its power, ground, clock, interface, and Ethernet differential pairs as a high-speed mixed-signal layout. Follow the manufacturer's recommended decoupling network, provide a clean 25 MHz reference-clock source, and route each 10/100 Ethernet differential pair as a controlled-impedance pair with minimal stubs. This page combines the family-level architecture, ordering distinctions, drop-in-replacement constraints, and practical PCB guidance into an engineering-focused selection resource. It also separates electrically compatible family members from package or interface changes that require board-level modification, helping designers avoid confusing a similar orderable code with a true pin-to-pin replacement.

RFQ Kontak
KSZ8842-16MVLI - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-16MVLI

KSZ8842-16MVLI - 2-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8842-16MVLI is a two-port 10/100 Base-T Ethernet switch with a generic 8/16-bit parallel CPU interface, supplied in a 128-LQFP package measuring 14 mm by 14 mm. It combines two Fast Ethernet network ports with cable diagnostics, programmable LED indication, and a low-power mode in one integrated network-interface controller. An Ethernet switch is a network-interface device that forwards Ethernet frames between attached ports while using a parallel host interface to exchange data and control information with an embedded processor. The KSZ8842 family sits within the Ethernet interface IC hierarchy: Ethernet switch controller, then network interface controller, then integrated interface circuit. Its 2-port arrangement supports compact embedded systems that require more than one wired-network connection without requiring a separate switch for each port. The KSZ8842-16MVLI provides two 10/100 Base-T/TX ports, a generic 8/16-bit parallel interface, MII and cable-diagnostics support, programmable LED outputs, and a low-power operating mode. The listed operating supply range is 3.1 V to 3.5 V. These functions make it suitable for industrial controllers, embedded gateways, set-top equipment, and other systems that need two Fast Ethernet links connected through one parallel CPU bus. The controller is intended for systems using a non-PCI parallel CPU interface. Its bus architecture allows 8-bit or 16-bit embedded-host operation, while the integrated switch manages communication between the two Ethernet ports. Because the device combines host-interface and network-switch functions, firmware must correctly configure port speed, duplex behavior, link status, and any low-power-mode transitions for its target platform. The KSZ8842 family includes PCI and non-PCI CPU-interface implementations. The KSZ8842-16MVLI is the non-PCI, 8/16-bit parallel-interface member, so it should not be confused with the PCI-interface KSZ8842-PMQL or KSZ8842-PMBL variants. It also differs from 32-bit bus members of the same family, which target a wider host data path. PCB implementation should preserve the 128-LQFP footprint and route the parallel bus, magnetics, Ethernet differential pairs, clock, reset, and control signals according to the manufacturer datasheet. Keep the Ethernet magnetics close to the corresponding ports and maintain controlled differential impedance to reduce reflections and radiated emissions. This product record consolidates electrical limits, package information, interface functions, sourcing guidance, and verified replacement considerations. The comparison also distinguishes genuine footprint-compatible options from related family members whose bus width, port count, interface type, or package prevents unqualified drop-in use.

RFQ Kontak
KSZ8842-32MVLI - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-32MVLI

KSZ8842-32MVLI - 2-Port 10/100 Ethernet Switch | Microchip

The Microchip KSZ8842-32MVLI is a two-port 10/100 Base-T Ethernet switch with a generic 32-bit parallel CPU interface, supplied in a 128-lead LQFP package measuring 14 x 14 mm. It supports 10 Mbps and 100 Mbps Ethernet operation, industrial-grade temperature classification, and a 3.1 V to 3.5 V operating range. The device is intended for embedded systems that require two integrated Fast Ethernet ports and direct host-bus connectivity without using a separate Ethernet controller. An Ethernet switch is a network-interface IC that forwards frames between multiple physical Ethernet ports while presenting one logical connection to a host processor. The KSZ8842 belongs to the KSZ8842 family of two-port switches, which includes PCI and non-PCI CPU-interface implementations. This non-PCI variant uses a generic parallel bus architecture, placing it in the interface-IC and embedded-Ethernet hierarchy rather than the standalone transceiver category. The principal features are two integrated 10/100 Ethernet ports, a generic 32-bit host interface, operation from 3.1 V to 3.5 V, and a 128-LQFP industrial package. The 32-bit bus provides a broad data path for transferring packet data between the Ethernet MACs and an embedded CPU. The 14 x 14 x 1.4 mm gull-wing package also supports surface-mount assembly, although its 128 leads require careful fanout, ground-plane, and signal-integrity layout. The KSZ8842 architecture separates network-port handling from host connectivity: integrated Ethernet PHY and MAC functions communicate with the external processor through the parallel bus. This approach can reduce the number of discrete network components in an embedded appliance. Exact propagation delay, throughput, media-access-control behavior, and electrical timing values must be confirmed against the manufacturer datasheet before defining a system-level Ethernet timing budget. Typical uses include industrial control panels, embedded routers, print servers, set-top boxes, building-control gateways, and networked test equipment. A compact appliance can connect one port to an upstream LAN and use the second port for a local device or downstream segment. In these systems, the non-PCI interface gives the CPU direct access to packet buffers and status registers while the integrated PHYs handle physical-layer signaling. PCB implementation requires careful treatment of the parallel host bus and both Ethernet channels. Place decoupling capacitors at the supply pins, maintain the specified impedance and routing geometry for differential pairs, and use a continuous ground reference beneath the device. Confirm pin assignments, exposed or connected ground leads, LED interfaces, crystal requirements, and reset behavior directly from the manufacturer datasheet before fabrication. This product page combines package and interface details, family alternatives, comparison criteria, and implementation guidance to support component selection and PCB planning. It also distinguishes a true same-footprint replacement from related devices that use different bus widths or package formats.

RFQ Kontak
KSZ8842-PMBL - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-PMBL

KSZ8842-PMBL - 2-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8842-PMBL is a two-port 10/100 Base-T Ethernet switch with a generic 32-bit, 33 MHz PCI processor interface, supplied in a 100-LFBGA 9 x 9 mm package. It provides two integrated 10/100 Ethernet ports, an integrated DMA engine, managed Layer 2 switching, and low-power operation for embedded networking equipment. An Ethernet switch is a network-semiconductor device that connects multiple physical network nodes while forwarding Ethernet frames according to Layer 2 addresses. The KSZ8842 belongs to the Ethernet switch hierarchy and integrates physical-layer transceivers, frame processing, port management, and a host-facing peripheral bus within one IC. Its PCI interface allows a processor or embedded controller to configure the switch, manage traffic, and exchange data with the connected Ethernet ports without requiring a separate external Ethernet controller. The manufacturer datasheet identifies the KSZ8842-PMQL/PMBL as the first fully managed two-port switch with a 32-bit, 33 MHz PCI processor interface. The device is compliant with IEEE 802.3u, supports 10/100 Base-T networking, and includes an integrated DMA engine for efficient host data movement. Its four-generation integrated Layer 2 switch architecture supports managed switching functions while reducing the component count of embedded Ethernet designs. The KSZ8842-PMBL is intended for compact PCI-based embedded systems where two Ethernet links are needed close to the host processor. Typical signal paths include industrial control equipment, embedded servers, communication appliances, test systems, and PCI expansion products. A 122 mA supply current value is identified for this device, making system-level power budgeting important when two ports operate continuously. The principal design consideration is the 100-LFBGA footprint. The board must provide the exact ball layout defined by the manufacturer package drawing and must accommodate the PCI, clock, power, reset, and Ethernet magnetics interfaces. Review the ordering information and pin-description tables in the manufacturer datasheet before assigning ball assignments or preparing the PCB footprint. The KSZ8842-PMBL is also the base commercial-temperature ordering code within the PMQL/PMBL PCI-interface family. The PMBL suffix identifies the LFBGA package, while the PMQL suffix identifies a different package. Industrial-temperature ordering variants include the -AM designation; verify the exact suffix, grade, and shipping configuration when substituting parts. This product page consolidates the known switch, interface, package, and ordering information with engineering-focused application guidance, replacement considerations, and a parameter comparison. It also distinguishes electrical or temperature-grade alternatives from packaging-only order codes so engineers can assess PCB compatibility before redesigning an existing LFBGA design.

RFQ Kontak
KSZ8842-PMBL-AM - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-PMBL-AM

KSZ8842-PMBL-AM - 2-Port 10/100 Ethernet Switch | Microchip

Microchip Technology KSZ8842-PMBL-AM is a fully managed, two-port Layer 2 Ethernet switch with a 32-bit, 33 MHz PCI processor interface, two 10/100 Base-T/TX ports, and a 100-LFBGA package measuring 9 x 9 mm. The device provides an industrial-temperature-grade option for embedded PCI networking systems requiring integrated switch management. An Ethernet switch is a semiconductor that connects multiple Ethernet nodes while using Layer 2 media-access-control addresses to forward frames. The KSZ8842 belongs to the broader network-interface hierarchy: Ethernet controller, network interface IC, interface IC, and integrated circuit. It integrates two Fast Ethernet PHYs and switch functions, reducing the need for separate Ethernet controllers or physical-layer devices in compact embedded equipment. The KSZ8842-PMBL-AM is based on Microchip's fourth-generation integrated Layer 2 switch architecture. Key features include two managed 10/100 ports, a 32-bit PCI interface operating at 33 MHz, IEEE 802.3u compliance, and an industrial-temperature-grade ordering option. Its small 100-LFBGA package supports space-constrained PCI host systems while exposing the complete two-port switching function on one device. The PCI host interface provides a direct path for a processor or embedded controller to configure the switch, exchange packet data, and access switch management registers. This integration is particularly useful when an embedded system needs two Ethernet ports but has limited board area or component count. Exact register behavior, interrupt architecture, and management features should be confirmed from the manufacturer's KSZ8842-PMQL/PMBL datasheet before final software configuration. Typical uses include industrial control systems, embedded routers, automated test equipment, POS terminals, and PCI-based communication appliances. In these applications, the two integrated Fast Ethernet ports can support a local equipment network, uplink, or network segmentation. The industrial-temperature designation makes the PMBL-AM version more appropriate for extended-temperature equipment than the standard PMBL ordering option. PCB implementation requires careful review of the 100-LFBGA land pattern, power and ground distribution, clock requirements, and high-speed signal routing. The 9 x 9 mm package is not a leaded package, so assembly capability, solder-mask definition, stencil aperture design, and via-in-pad or thermal-via requirements must be coordinated with the board manufacturer before release. This product analysis consolidates the manufacturer architecture description, package information, ordering distinctions, replacement considerations, and PCB implementation guidance into an engineering-focused resource for evaluating the KSZ8842-PMBL-AM in compact embedded Ethernet systems.

RFQ Kontak
KSZ8842-PMBL-TR - 2-Port 10/100 Ethernet Switch | Microchip (Tape & Reel)
KSZ8842-PMBL-TR

KSZ8842-PMBL-TR - 2-Port 10/100 Ethernet Switch | Microchip (Tape & Reel)

The Microchip Technology KSZ8842-PMBL-TR is a two-port 10/100 Base-T Ethernet switch with a generic 32-bit, 33 MHz PCI processor interface, supplied in a 100-LFBGA 9 x 9 mm package. It provides two integrated 10/100 Ethernet ports, an integrated DMA engine, managed Layer 2 switching, and low-power operation for embedded networking equipment. An Ethernet switch is a network-semiconductor device that connects multiple physical network nodes while forwarding Ethernet frames according to Layer 2 addresses. The KSZ8842 belongs to the Ethernet switch hierarchy and integrates physical-layer transceivers, frame processing, port management, and a host-facing peripheral bus within one IC. Its PCI interface allows a processor or embedded controller to configure the switch, manage traffic, and exchange data with the connected Ethernet ports without requiring a separate external Ethernet controller. The manufacturer datasheet identifies the KSZ8842-PMQL/PMBL as the first fully managed two-port switch with a 32-bit, 33 MHz PCI processor interface. The device is compliant with IEEE 802.3u, supports 10/100 Base-T networking, and includes an integrated DMA engine for efficient host data movement. Its four-generation integrated Layer 2 switch architecture supports managed switching functions while reducing the component count of embedded Ethernet designs. The KSZ8842-PMBL-TR is intended for compact PCI-based embedded systems where two Ethernet links are needed close to the host processor. Typical signal paths include industrial control equipment, embedded servers, communication appliances, test systems, and PCI expansion products. A 122 mA supply current value is identified for this device, making system-level power budgeting important when two ports operate continuously. The principal design consideration is the 100-LFBGA footprint. The board must provide the exact ball layout defined by the manufacturer package drawing and must accommodate the PCI, clock, power, reset, and Ethernet magnetics interfaces. Review the ordering information and pin-description tables in the manufacturer datasheet before assigning ball assignments or preparing the PCB footprint. The KSZ8842-PMBL-TR is also the base commercial-temperature ordering code within the PMQL/PMBL PCI-interface family. The PMBL suffix identifies the LFBGA package, while the PMQL suffix identifies a different package. Industrial-temperature ordering variants include the -AM designation; verify the exact suffix, grade, and shipping configuration when substituting parts. This product page consolidates the known switch, interface, package, and ordering information with engineering-focused application guidance, replacement considerations, and a parameter comparison. It also distinguishes electrical or temperature-grade alternatives from packaging-only order codes so engineers can assess PCB compatibility before redesigning an existing LFBGA design.

RFQ Kontak
KSZ8842-PMQL - 2-Port 10/100 PCI Ethernet Switch | Microchip
KSZ8842-PMQL

KSZ8842-PMQL - 2-Port 10/100 PCI Ethernet Switch | Microchip

Microchip Technology KSZ8842-PMQL is a fully managed two-port 10/100 Ethernet switch with a generic 32-bit, 33 MHz PCI processor interface, housed in a 128-pin PQFP package measuring 14 mm by 20 mm. The device provides two integrated Fast Ethernet ports, an integrated DMA engine, and low-power operation for PCI-based embedded networking designs. An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between connected nodes while using MAC-address learning to reduce unnecessary traffic. Within the network hierarchy, the KSZ8842-PMQL is an Ethernet interface IC and network interface controller that connects a PCI host processor to two 10/100 Base-TX ports. Its managed-switch architecture supports centralized port control, status monitoring, and traffic management in embedded industrial, communications, and legacy PCI systems. Key features include two integrated 10/100 Ethernet ports, a 32-bit PCI interface operating at 33 MHz, IEEE 802.3u compliance, an integrated DMA engine, and a low-power operating design. The PQFP package provides 128 accessible package positions and uses leaded technology for compatibility with established PCI motherboard and embedded-controller assemblies. An industrial-temperature ordering option, KSZ8842-PMQLI, extends the family for applications requiring extended temperature operation. Architecturally, the KSZ8842-PMQL belongs to the KSZ8842 fourth-generation integrated Layer 2 switch family. Separate PCI and non-PCI implementations allow designers to match the host interface to the platform, while the PMQL version retains the 32-bit PCI processor connection. The integrated DMA engine assists efficient packet transfer between the PCI host and switch ports, reducing the processing burden associated with moving Ethernet traffic through host memory. Typical applications include PCI-based industrial controllers, embedded communications appliances, test and measurement systems, legacy PCI server equipment, and custom network interface cards. The device is particularly suitable when two copper Ethernet ports are required without adding an external two-port switch. Designers must also verify the host platform's supported PCI electrical characteristics, bus width, clocking, and software configuration model before releasing a new design. For a new design, route each differential Ethernet pair through a controlled-impedance layout, keep the PHY and magnetics interface routing compact, and follow the manufacturer's reference layout for power, ground, reset, and clock connections. Because this is a legacy PCI bridge with a large leaded package, confirm long-term sourcing and lifecycle status with Microchip before committing to high-volume production. This page combines the exact manufacturer and distributor identification for KSZ8842-PMQL with package, interface, application, and procurement guidance. It also distinguishes the PCI implementation from related non-PCI KSZ8842 members and identifies the temperature-graded PMQLI counterpart for industrial design reviews.

RFQ Kontak
KSZ8851-16MLLI - 10/100 Ethernet Controller | Microchip Technology
KSZ8851-16MLLI

KSZ8851-16MLLI - 10/100 Ethernet Controller | Microchip Technology

Microchip Technology KSZ8851-16MLLI is a single-port 10/100 Base-T Ethernet MAC controller with an integrated 10/100 Base-T/TX PHY, a generic 8-bit or 16-bit non-PCI host interface, and a 48-LQFP 7 x 7 mm package. The integrated controller and PHY combination supports cost-effective, high-throughput Ethernet connectivity for traditional embedded systems that do not require a PCI interface. An Ethernet MAC controller is a network-interface semiconductor that manages frame transmission, reception, addressing, and the host-side data path between an embedded processor and an Ethernet network. By integrating the MAC and physical-layer functions, the KSZ8851 reduces external PHY count, board area, and implementation effort while supporting the established IEEE 802.3 Ethernet framework. The device supports 10 Mbps and 100 Mbps operation through its 10/100 Base-T/TX PHY. Its generic non-PCI interface can operate as an 8-bit or 16-bit host bus, allowing integration with embedded processors, microcontrollers, and programmable logic that do not implement a PCI controller. The industrial-grade MLLI ordering option is offered in the same 48-LQFP package used by related KSZ8851 variants. The KSZ8851 family provides multiple interface widths and package configurations, including 8-, 16-, and 32-bit versions, allowing design reuse across embedded platforms. Its integrated analog receive and transmit circuitry is intended to support physical-layer signal transmission and reception while the MAC subsystem manages packet-level communication with the host processor. Typical applications include industrial automation equipment, embedded control systems, factory monitoring terminals, networked sensors, building-automation controllers, and compact communication gateways. A typical design connects the host bus to the KSZ8851, routes the controller through an RJ45 magnetics section, and uses magnetic or non-magnetic Ethernet physical-interface components appropriate to the board environment. When laying out the board, keep the Ethernet differential pairs short, impedance-controlled, and isolated from noisy digital and switching-power paths. Follow the manufacturer’s recommended decoupling, clock, reset, and magnetics-layout guidance because PHY signal integrity and clock jitter directly affect link reliability, packet errors, and the ability to establish a stable 100 Mbps connection. This page combines the manufacturer interface description, package and speed characteristics, sourcing structure, practical PCB guidance, and an application-oriented comparison with verified KSZ8851 ordering options. It also distinguishes true same-footprint alternatives from package variants that would require a PCB redesign.

RFQ Kontak
KSZ8851-16MLLJ - 10/100 Ethernet Controller | Microchip
KSZ8851-16MLLJ

KSZ8851-16MLLJ - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8851-16MLLJ is a single-port 10/100 Ethernet MAC controller with an integrated 10/100 Base-T/TX PHY, parallel host interface, and 48-pin LQFP package measuring 7 mm by 7 mm. It is designed to add cost-effective Ethernet connectivity to traditional embedded systems that do not require PCI Express. An Ethernet MAC controller is an interface IC that manages packet transmission, reception, addressing, and host-bus transactions, while a Base-T/TX PHY provides the physical-layer connection to twisted-pair Ethernet. Together, the MAC and PHY form a complete single-port Ethernet endpoint for embedded processors, industrial controllers, test equipment, and connected products. The KSZ8851 family supports configurable generic processor interfaces. The 16-bit MLLJ configuration provides an 8-bit or 16-bit non-PCI host interface, allowing the controller to connect with embedded processors that use parallel buses rather than SPI or PCI Express. The controller also uses dynamic memory pointers for efficient descriptor-based packet management. The integrated MAC, PHY, and host interface consolidate several Ethernet functions into one package. This can reduce external component count and simplify the board-level connection between the processor and RJ45 network interface. The 48-LQFP package has exposed leads suitable for conventional surface-mount assembly and inspection. Typical applications include industrial automation, factory equipment, building controls, embedded instrumentation, serial-to-Ethernet gateways, print servers, and embedded network appliances. The device is particularly appropriate when a system needs a deterministic parallel host connection and a conventional 10/100 Ethernet network rather than a higher-speed multi-gigabit interface. Designers should use the manufacturer pin-description table when assigning processor signals, PHY connections, clocks, reset inputs, and decoupling networks. Magnetics and connector selection must be matched to the Ethernet application, while the host bus must support the selected 8-bit or 16-bit operating mode and required address and data timing. This page organizes the manufacturer product information, package details, datasheet links, interface alternatives, and practical implementation guidance. It is intended to help engineers identify whether the KSZ8851-16MLLJ matches the required Ethernet speed, parallel bus architecture, package, temperature class, and embedded-system application.

RFQ Kontak
KSZ8851-16MLLU - 10/100 Ethernet Controller | Microchip
KSZ8851-16MLLU

KSZ8851-16MLLU - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8851-16MLLU is a single-port 10/100 Ethernet MAC controller with an integrated Ethernet PHY and a 16-bit parallel non-PCI host interface, supplied in a 48-LQFP package. It supports 1.8 V, 2.5 V, and 3.3 V interface operation and is the AEC-Q100-qualified automotive version of the KSZ8851-16MLL family. An Ethernet MAC controller is an interface IC that connects a host processor to an Ethernet physical layer. The MAC portion manages frame processing and host-interface transactions, while the integrated PHY provides the electrical connection to a 10BASE-T or 100BASE-TX network. Together, these functions add wired network connectivity to embedded systems without requiring a separate Ethernet transceiver. The KSZ8851-16MLLU is intended for cost-effective, high-throughput Ethernet designs using conventional embedded processors rather than PCI-based host systems. Its 16-bit parallel interface provides a direct processor connection, while the family also supports SPI and other non-PCI interface configurations. The device is offered in 32-, 48-, and 128-pin package options within the KSZ8851 family, with the selected 48-LQFP configuration balancing functional capability and board-space requirements. Analog signal transmission and reception are part of the integrated PHY design, allowing the controller to support physical-network connectivity without a discrete PHY. The automotive-qualified MLLU variant is relevant to vehicle and other automotive electronics platforms where environmental qualification and product traceability are required. The manufacturer datasheet identifies the design as compliant with applicable IEEE 802.3 standards. Typical uses include automotive body, infotainment, telematics, and gateway modules, along with industrial Ethernet controllers, embedded network equipment, and communication appliances. The 10/100 capability is appropriate for legacy and cost-sensitive networks where gigabit Ethernet is unnecessary, while the parallel host interface can simplify integration with processors that do not provide Ethernet MAC/PHY peripherals. PCB design should follow the manufacturer’s package, decoupling, clock, and analog-impedance guidance. The Ethernet differential pair requires careful routing and controlled impedance, and power and ground connections must be kept stable around the integrated analog and digital sections. Confirm the exact pin assignments, resistor values, and external components in the KSZ8851-16MLL datasheet before finalizing the PCB. This page combines package, interface, qualification, comparison, replacement, and design guidance to support component selection and PCB planning. It focuses on the KSZ8851-16MLLU automotive 48-LQFP configuration and distinguishes it from temperature-grade, interface, and packaging variants that may otherwise appear similar in catalog searches.

RFQ Kontak
KSZ8851-16MQLI - 10/100 Ethernet MAC Controller | Microchip
KSZ8851-16MQLI

KSZ8851-16MQLI - 10/100 Ethernet MAC Controller | Microchip

The Microchip Technology KSZ8851-16MQLI is a single-port 10/100 Ethernet MAC controller with an integrated 10BASE-T and 100BASE-TX PHY, an 8-bit or 16-bit generic parallel CPU interface, and a 3.3 V supply in a 128-pin PQFP package measuring 14 x 20 mm. It supports 10 Mbit/s and 100 Mbit/s Ethernet operation for cost-effective connectivity in traditional embedded systems. An Ethernet MAC controller is a semiconductor that connects a processor or microcontroller to a physical Ethernet network. The MAC sublayer manages frame transmission, reception, addresses, and error detection, while the integrated PHY converts between digital Ethernet data and analog signals on the network. The KSZ8851 therefore places both functions in one device instead of requiring a separate Ethernet PHY and dedicated network controller. The KSZ8851 family provides a generic 8-bit, 16-bit, or 32-bit non-PCI interface, plus SPI interface options in the wider product family. The -16MQLI configuration is supplied in a 128-pin PQFP and includes 18 KB of on-chip memory as listed for this exact orderable part. Operating from 3.3 V, the device is suited to embedded industrial control, building automation, networking equipment, test systems, and communication appliances that require 10/100 Ethernet without a PCI interface. The 128-pin package exposes the parallel host bus, Ethernet physical-layer signals, clock and reset inputs, power connections, and interrupt signaling. Because the device combines a PHY and MAC, PCB implementation also requires careful separation of analog and digital return paths. The manufacturer's KSZ8851-16/32MQL datasheet describes the 8-bit and 16-bit generic processor interfaces used by this configuration and provides the authoritative reference for pin assignments, timing, and electrical limits. Typical designs connect the parallel bus to an embedded processor, an RJ45 magnetic network interface, and a 3.3 V regulator. The Ethernet magnetics perform isolation and impedance matching, while the controller manages access to the network medium. Software drivers for the KSZ8851 are used with common embedded processors, including STM32-class systems, and interrupt-driven operation reduces the need for continuous host polling. During schematic design, reserve the Ethernet differential pair for direct connection between the PHY and network magnetics, and avoid placing high-current digital return paths beneath the analog section. Follow the reference circuit and decoupling recommendations in the manufacturer datasheet for capacitors, crystals, reset sequencing, and analog supply connections. This page combines the exact 128-pin orderable configuration with package, interface, application, and selection information designed to help engineers evaluate the KSZ8851-16MQLI against lower-pin-count KSZ8851 options before committing a PCB layout.

RFQ Kontak
KSZ8851-32MQLI - 10/100 Ethernet Controller | Microchip
KSZ8851-32MQLI

KSZ8851-32MQLI - 10/100 Ethernet Controller | Microchip

Microchip Technology KSZ8851-32MQLI is a single-port 10/100 Base-T Ethernet MAC controller with an integrated PHY and a generic 32-bit parallel CPU interface. The device operates from a 3.1 V to 3.5 V core supply and is packaged in a 128-pin PQFP measuring 14 mm by 20 mm. It is intended for embedded systems that require economical, high-throughput Ethernet connectivity without PCI. An Ethernet MAC controller is an interface integrated circuit that manages frame handling and connects a processor or other bus-based host to an Ethernet physical layer. The KSZ8851 combines the MAC, a 10/100 Base-T/TX PHY, LED indication, wake-up functionality, and a low-power operating mode in one device. Within the semiconductor hierarchy, it belongs to the Ethernet controller and network-interface IC class rather than a general-purpose processor or standalone Ethernet transceiver. The -32MQLI configuration provides a 32-bit non-PCI host interface, making it suitable for embedded processors that can accommodate a wide parallel bus. The 10/100 capability supports legacy Fast Ethernet networks, while the integrated PHY reduces the external component count compared with separate MAC and PHY implementations. Programmable LED indication supports simplified link, activity, and speed-status reporting, and the documented wake-up and low-power features can improve system responsiveness and energy behavior. The KSZ8851 family is offered in 32-, 48-, and 128-pin packages, allowing the same controller family to address different host-interface and board-space requirements. This specific 128-pin PQFP variant provides a conventional parallel-bus connection to the embedded CPU while keeping the Ethernet MAC and physical-layer functions together. Microchip describes the family as a cost-effective solution for adding Ethernet to traditional embedded systems. Typical uses include industrial controllers, embedded data loggers, factory equipment, building-automation gateways, and network-accessible test instruments. In these systems, the host processor can exchange Ethernet frames through the generic 32-bit bus while the controller handles the physical 10/100 link. Systems requiring additional network ports can pair it with a managed Ethernet switch or multi-port PHY while retaining a conventional processor-centric architecture. PCB design should account for the 128-pin PQFP footprint, controlled-impedance signal routing for the parallel host bus, and separation between high-speed digital signals and the Ethernet magnetics and network-side routing. Follow the manufacturer’s reference schematic, component values, and layout guidance in datasheet DS00002425B. The system designer must also verify clock, reset, interrupt, PHY, and power-supply requirements against the complete device pin-description table before releasing the PCB. This product page combines the manufacturer family description with distributor package information, sourcing guidance, application analysis, and engineering design notes. It also distinguishes the exact 32-bit industrial-temperature ordering code from related family members so that engineers can review footprint, interface width, and qualification requirements before committing a design to the PCB.

RFQ Kontak
KSZ8851SNL - 10/100 Ethernet Controller | Microchip
KSZ8851SNL

KSZ8851SNL - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8851SNL is a single-port 10/100 Ethernet controller with a 3.3 V SPI interface, integrated 10/100BASE-T/TX PHY, and Media Access Controller in a 32-pin QFN package measuring 5 mm x 5 mm. It provides 10 Mbps and 100 Mbps Ethernet connectivity for embedded systems using a host microcontroller equipped with an SPI interface. The device also includes one copper port and one uplink port, making it suitable for industrial, communications, building-automation, and networked embedded-control equipment. An Ethernet controller is an interface IC that integrates network-frame handling with physical-layer signaling. The KSZ8851 family combines the PHY and MAC with an SPI host interface, reducing the number of external components required to add wired Ethernet to a microcontroller-based product. This integration places the KSZ8851 within the hierarchy of Ethernet controller, network interface controller, interface IC, and semiconductor. Its SPI host interface supports a compact connection to embedded processors while preserving an independent Ethernet data path. The principal verified features are 10/100BASE-T/TX operation, a 3.3 V supply as identified by the distributor specification snippet, and a 32-pin lead-free QFN package. The integrated controller architecture simplifies firmware and hardware compared with a separated Ethernet MAC and external PHY arrangement. A single-port design also keeps board area and component count controlled, which is valuable in embedded products where connector placement, enclosure volume, and system cost are constrained. Technically, the KSZ8851SNL separates host access from Ethernet processing through its Serial Peripheral Interface. The SPI interface provides a compact communication path for register access, configuration, interrupt handling, and Ethernet data transfer. The integrated PHY handles the physical signaling required for 10/100BASE-T/TX copper networking, while the MAC performs the higher-level frame-processing functions required to present Ethernet traffic to the host processor. Typical applications include industrial Ethernet gateways, building-automation controllers, serial-to-Ethernet equipment, embedded test systems, HMI platforms, and network-connected sensors. It is also appropriate for custom industrial control equipment requiring a dedicated Ethernet port without allocating a high-performance host processor for basic Ethernet connectivity. The 5 mm x 5 mm QFN package supports compact designs, although exposed-pad layout and thermal management remain PCB-level concerns. Designers should follow Microchip's KSZ8851SNL Hardware Design Checklist for power, decoupling, magnetics, differential routing, and copper interface implementation. SPI trace integrity, grounding, and isolation requirements must be reviewed alongside the Ethernet physical layer because the controller is intended for copper-connected industrial networks rather than direct cable attachment without supporting network hardware.

RFQ Kontak
KSZ8851SNLI - 10/100 Ethernet SPI Controller | Microchip
KSZ8851SNLI

KSZ8851SNLI - 10/100 Ethernet SPI Controller | Microchip

The Microchip Technology KSZ8851SNLI is an industrial-temperature-grade, single-port Fast Ethernet controller integrating a 10/100BASE-T/TX physical-layer transceiver, a Media Access Controller, and a Serial Peripheral Interface in a 32-QFN (5x5 mm) package. It connects a host microcontroller with an SPI interface to copper Ethernet and supports the 10 Mbps and 100 Mbps transfer rates of Fast Ethernet. A Fast Ethernet controller is a network-interface semiconductor that combines physical-layer signaling and higher-level frame processing. Within the product hierarchy, the KSZ8851SNLI is an Ethernet controller interface IC with an integrated Ethernet PHY and MAC. Its SPI host interface provides a practical way to add wired network connectivity to embedded systems without requiring a parallel host bus or a dedicated Ethernet processor. Key device features include a single Ethernet port, integrated 10/100BASE-T/TX PHY, integrated MAC, and an SPI interface. The manufacturer documentation identifies 3.3 V as the main supply and provides 1.8 V, 2.5 V, and 3.3 V options for VDD I/O, allowing the digital interface voltage to be matched more closely to the host microcontroller. The SNLI designation identifies the industrial-temperature-grade version of the KSZ8851SNL family. The KSZ8851SNL family supports SPI, 8-bit, 16-bit, and 32-bit non-PCI CPU interfaces, with package options of 32, 48, and 128 pins. The 32-QFN KSZ8851SNLI is therefore the SPI-oriented option for compact embedded equipment. Integrating the PHY and MAC reduces the number of external Ethernet interface functions required, while the SPI connection limits host-side wiring and allows a microcontroller to manage registers and network traffic through a serial interface. Typical uses include industrial monitoring, networked sensors, building controls, embedded access equipment, and compact gateway products. For these systems, the device can provide a single 10/100 copper port while the host handles application traffic, configuration, and network management. A board design must still provide the required magnetic interface, termination, reference circuitry, clocking, supply rails, and controlled-layout implementation described by the manufacturer hardware checklist. Designers should evaluate the SPI clock and signal-integrity requirements, power-supply sequencing, and Ethernet magnetics together rather than treating the controller as a stand-alone Ethernet jack interface. The 3.3 V supply and selectable 1.8 V, 2.5 V, or 3.3 V VDD I/O levels are important for host compatibility, while the compact 5x5 mm QFN footprint requires a land pattern and thermal strategy appropriate for a leadless package. This page combines the manufacturer identification, SPI and 10/100 Ethernet capabilities, verified-source links, and practical engineering guidance. It also distinguishes the directly documented same-family option from cross-package Ethernet devices, helping engineers make a footprint-aware choice without treating every Ethernet PHY as a drop-in replacement.

RFQ Kontak
KSZ8851SNLI-TR - 10/100 Ethernet SPI Controller | Microchip (Tape & Reel)
KSZ8851SNLI-TR

KSZ8851SNLI-TR - 10/100 Ethernet SPI Controller | Microchip (Tape & Reel)

The Microchip Technology KSZ8851SNLI-TR is an industrial-temperature-grade, single-port Fast Ethernet controller integrating a 10/100BASE-T/TX physical-layer transceiver, a Media Access Controller, and a Serial Peripheral Interface in a 32-QFN (5x5 mm) package. It connects a host microcontroller with an SPI interface to copper Ethernet and supports the 10 Mbps and 100 Mbps transfer rates of Fast Ethernet. A Fast Ethernet controller is a network-interface semiconductor that combines physical-layer signaling and higher-level frame processing. Within the product hierarchy, the KSZ8851SNLI-TR is an Ethernet controller interface IC with an integrated Ethernet PHY and MAC. Its SPI host interface provides a practical way to add wired network connectivity to embedded systems without requiring a parallel host bus or a dedicated Ethernet processor. Key device features include a single Ethernet port, integrated 10/100BASE-T/TX PHY, integrated MAC, and an SPI interface. The manufacturer documentation identifies 3.3 V as the main supply and provides 1.8 V, 2.5 V, and 3.3 V options for VDD I/O, allowing the digital interface voltage to be matched more closely to the host microcontroller. The SNLI designation identifies the industrial-temperature-grade version of the KSZ8851SNL family. The KSZ8851SNL family supports SPI, 8-bit, 16-bit, and 32-bit non-PCI CPU interfaces, with package options of 32, 48, and 128 pins. The 32-QFN KSZ8851SNLI-TR is therefore the SPI-oriented option for compact embedded equipment. Integrating the PHY and MAC reduces the number of external Ethernet interface functions required, while the SPI connection limits host-side wiring and allows a microcontroller to manage registers and network traffic through a serial interface. Typical uses include industrial monitoring, networked sensors, building controls, embedded access equipment, and compact gateway products. For these systems, the device can provide a single 10/100 copper port while the host handles application traffic, configuration, and network management. A board design must still provide the required magnetic interface, termination, reference circuitry, clocking, supply rails, and controlled-layout implementation described by the manufacturer hardware checklist. Designers should evaluate the SPI clock and signal-integrity requirements, power-supply sequencing, and Ethernet magnetics together rather than treating the controller as a stand-alone Ethernet jack interface. The 3.3 V supply and selectable 1.8 V, 2.5 V, or 3.3 V VDD I/O levels are important for host compatibility, while the compact 5x5 mm QFN footprint requires a land pattern and thermal strategy appropriate for a leadless package. This page combines the manufacturer identification, SPI and 10/100 Ethernet capabilities, verified-source links, and practical engineering guidance. It also distinguishes the directly documented same-family option from cross-package Ethernet devices, helping engineers make a footprint-aware choice without treating every Ethernet PHY as a drop-in replacement.

RFQ Kontak
KSZ8863FLL - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology
KSZ8863FLL

KSZ8863FLL - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology

The Microchip Technology KSZ8863FLL is a highly integrated three-port 10/100 managed Ethernet switch with integrated PHYs, one 100BASE-FX fiber port, one 10/100BASE-TX copper port, and one additional 10/100 port. It supports 10/100 Mbps Ethernet switching, MII connectivity, and CPU control through I2C or SPI. The device is packaged in a 48-LQFP package measuring 7 mm by 7 mm. According to the verified product description, the KSZ8863FLL is intended for low-port-count, cost-sensitive, and power-efficient 10/100 Mbps switch systems. An Ethernet switch is a networking semiconductor that connects multiple Ethernet endpoints and forwards frames between ports using integrated physical-layer transceivers, or PHYs. The managed-switch category adds configuration and control functions beyond basic frame forwarding, including port management, VLAN support, QoS priority handling, and CPU-controlled data interfaces. The KSZ8863FLL belongs to the switch-on-a-chip family, combining multiple Ethernet ports and management functions into one device rather than requiring separate discrete PHY and switch components. Key verified features include a three-port architecture, integrated PHYs, 100BASE-FX fiber support, 10/100BASE-TX copper networking, one MII interface, and CPU control and data interfaces. The product is identified by DigiKey as an Ethernet Switch with a 1.8 V, 2.5 V, or 3.3 V supply option and a 48-LQFP 7 x 7 mm package. Microchip describes the KSZ8863 family as supporting switch management, port and tag-based VLAN, QoS priority, and CPU control, which makes it suitable for compact embedded-network equipment. The KSZ8863FLL is positioned for industrial, communications, and embedded Ethernet designs that need copper and fiber connectivity in a small package. Its integrated approach can reduce board-level component count and simplify the network architecture compared with a discrete switch implementation. The MII interface allows connection to a host processor or another Ethernet-compatible controller, while I2C or SPI management access supports configuration from a microcontroller or embedded system. Designers should verify the exact pinout, transceiver requirements, clocking, magnetics, and fiber-interface implementation against the manufacturer datasheet before layout. Although the MLL, FLL, and RLL variants belong to the same KSZ8863 family, their supported interfaces and features differ, so substitution must be checked carefully. The verified data does not provide complete electrical limits, pin names, or pricing, and those values are marked as needed rather than estimated. This page combines the verified KSZ8863FLL product identity, package information, application positioning, and datasheet references with practical selection guidance. It also distinguishes direct family substitutions from broader Ethernet-switch alternatives that may require PCB, firmware, or interface changes.

RFQ Kontak
KSZ8863FLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology
KSZ8863FLLI

KSZ8863FLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology

The Microchip Technology KSZ8863FLLI is a highly integrated 3-port 10/100 managed Ethernet switch with fiber support, packaged in a 48-LQFP 7x7 mm package. It is designed for cost-sensitive, power-efficient low-port-count network systems and provides integrated 10/100 Ethernet PHYs with I2C and SPI control interfaces. The device supports 10 Mbps and 100 Mbps data rates and is identified as a 3-port Ethernet switch controller with Base-FX/T/TX PHY functionality. An Ethernet switch controller is an interface IC that integrates multiple physical-layer transceivers and switching logic into one device. It sits within the hierarchy of Ethernet interface ICs, network controllers, semiconductors, and broader communications equipment. By combining copper and fiber-oriented connectivity in a compact package, the KSZ8863 family is intended to reduce external component count in embedded gateways, industrial controllers, access equipment, and compact network appliances. The KSZ8863FLLI includes support for optical fiber, cable diagnostics, programmable LED indication, and a low-power operating mode. Its managed-switch architecture supports controlled network segmentation and status indication, while the integrated PHYs simplify connections to 10/100BASE-T and fiber-capable downstream equipment. The I2C and SPI interfaces provide host access for configuration and management functions. According to the manufacturer product description, the KSZ8863 series is cost-sensitive, power efficient, and optimized for low-port-count switching systems. The family variants use different suffix options to address product and ordering requirements while retaining a closely related 3-port 10/100 managed-switch architecture. The KSZ8863FLLI is supplied in a 48-LQFP package, enabling conventional surface-mount assembly in industrial and embedded equipment. Its operating temperature range is specified as -40°C to +85°C, making it suitable for extended industrial environments. The 100 Mbps data rate and fiber support distinguish it from basic single-port Ethernet PHY devices. Typical applications include industrial Ethernet gateways, serial-to-Ethernet equipment, access-point controllers, factory automation nodes, and compact embedded network appliances. Because the device combines managed switching, integrated PHYs, programmable LEDs, and low-power operation, it can simplify board design where a small network topology must operate without a discrete switch and multiple PHY packages. The main design consideration is power and signal integrity: place the device and its decoupling network according to the manufacturer reference layout, keep high-speed traces controlled, and validate Ethernet magnetics or fiber interfaces in the final board design. Also confirm the exact fiber, LED, and management configuration for the selected KSZ8863 variant before production release. This product page combines the verified manufacturer and distributor information, identifies package and interface details, and provides practical guidance for Ethernet switch design, sourcing, and qualification. The documented alternatives are organized by manufacturer priority and intended for engineering comparison rather than as automatic substitutions without footprint and configuration verification.

RFQ Kontak