Microchip Technology

KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip

MPN: KSZ8795CLXIC ✓ Nakahanda
3.3 V Vdss 80-LQFP (10 x 10 mm) Package 10/100 Mbps per port (Ports 1-4) Speed
MOQ: 1 |

KSZ8795CLXIC Ulas

The Microchip Technology KSZ8795CLXIC is a Layer 2 managed, highly integrated 5-port Ethernet switch with four 10/100BASE-T/TX copper ports and one 10/100/1000BASE-T Gigabit uplink port, delivering configurable GMII, RGMII, MII and RMII host interfaces from an 80-LQFP (10 x 10 mm) package. It operates from a single 3.3 V supply and is offered in an industrial-temperature ordering code.

An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between multiple physical ports using a MAC address table. In this device family, the switch also integrates 10/100BASE-T/TX PHYs with internal biasing resistors, on-chip termination and auto-negotiation, so a single silicon device replaces discrete magnetics-heavy copper PHY circuitry. The KSZ8795CLXIC therefore sits in the hierarchy: Ethernet switch > Layer 2 managed switch > integrated copper PHY switch > network interface IC.

Key features include four 10/100Mbps copper ports with auto-MDIX support, a Gigabit-capable uplink port, IEEE 802.3u compliant operation, MIIM and SPI management interfaces, and on-chip port termination that eliminates external resistor networks. Low power consumption is achieved through internal biasing rather than external resistor dividers, and the small package outline reduces board area versus discrete implementations.

Internally the device combines a five-port frame buffer with an integrated 10/100 MAC/PHY per copper port and a configurable uplink MAC supporting GMII, RGMII, MII and RMII. Management is handled by a MIIM register interface and an SPI host interface, giving the system processor access to VLAN, QoS, port enable and mirror registers. The design is intended for cost-sensitive embedded equipment where a single high-integration switch replaces several discrete PHYs and magnetics.

Typical applications include industrial control gateways, industrial Ethernet switches and PLC communication modules, IP cameras and surveillance recorders, industrial IoT and building-automation nodes, and consumer or telecom CPE equipment with a Gigabit uplink. The configurable uplink lets one design serve either RGMII-based application processors or RMII-based microcontrollers.

Keep the analog and digital ground pins tied to a single solid, contiguous ground plane. Microchip explicitly warns that splitting GDNA and GNDD into separate planes causes frame drops, so route both to the same uninterrupted system ground and place the port magnetics with short, tightly-coupled differential pairs to preserve return-path integrity.

This page combines the manufacturer switch specifications, distributory pricing structure, pin-compatible 80-LQFP alternatives, and practical layout and thermal guidance that you would otherwise have to reconstruct from several separate documents.

Mga alternatibo na pwedeng ilagay na KSZ8795CLXIC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

KSZ8765CLX

✅ Drop-In
📦 80-LQFP (10 x 10 mm)
Same 80-pin LQFP footprint and pin-compatible per Microchip support guidance; uplink is 10/100Mbps only versus 10/100/1000Mbps on the KSZ8795CLXIC, a -1000 Mbps reduction on Port 5

📋 Alternatibo na Reference (hindi sa katalogo)

KSZ8765CLXIC

✅ Drop-In
Microchip Technology
📦 80-LQFP (10 x 10 mm)
Layer 2-managed Ethernet switch · 5 ports · 10/100 Mbps · 4 ports · 1 port at 10/100/1000 Mbps · 100 Mbps 100Base-FX · 2 ports · GMII, RGMII, MII, and RMII

Magkontak para sa presyo

Tingnan ang Datasheet →

KSZ8795CLX

✅ Drop-In
📦 80-LQFP (10 x 10 mm)
Identical silicon and 80-LQFP footprint; the IC suffix denotes the industrial-temperature tray ordering code, so electrical behavior matches with 0 Mbps difference in port speed

📋 Alternatibo na Reference (hindi sa katalogo)

KSZ8795CLXIC Mga Pinakamataas na Rating at Electrical Characteristics

Device Type Integrated Layer 2 managed 5-port 10/100 Ethernet switch with Gigabit uplink
Number of Ports 5 (Ports 1-4 copper 10/100Mbps, Port 5 uplink)
Copper Port Speed 10/100 Mbps per port (Ports 1-4)
Uplink Port Speed 10/100/1000 Mbps (Port 5)
Host Interface Options GMII, RGMII, MII, RMII (configurable on Port 5)
Management Interface MIIM register access and SPI host interface
Volte ng Pagbibigay 3.3 V
Packhaging 80-LQFP (10 x 10 mm)
Uri ng Pagpapasok Surface Mount
On-Chip Features Internal biasing, on-chip termination, internal PHY
Power Consumption Lowest power consumption in class via internal biasing
Ethernet Compliance IEEE 802.3u 10BASE-T/100BASE-TX
Ethernet Media Features 10/100BASE-T/TX PHY with auto-MDIX
Ordering Code Suffix IC = industrial temperature, tray packaging
Tindminan RoHS RoHS Compliant
Katayuan ng Lifecycle Active
Datasheet Document Number 00002112B
Datasheet Length 132 pages
Hardware Design Checklist Document KSZ8795CLX Hardware Design Checklist, document 00003579B

Gabay sa Pin Configuration ng KSZ8795CLXIC 80-lqfp (10 x 10 mm)

Pin configuration para sa KSZ8795CLXIC (80-lqfp (10 x 10 mm) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 80-lqfp (10 x 10 mm) package para sa KSZ8795CLXIC

Wala ng detalyadong pinout data na magagamit para sa KSZ8795CLXIC.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

KSZ8795CLXIC ay nararapat para sa 6 aplikasyons: Industrial Ethernet Switch and Gateway, IP Camera and Surveillance Network Node, Industrial IoT and Building Automation Node, Consumer and Telecom Customer Premises Equipment, Embedded Linux SoC Network Interface, PLC and Programmable Controller Communication Module.

🏭

Industrial Ethernet Switch and Gateway

The KSZ8795CLXIC suits industrial gateways that must aggregate four 10/100Mbps field devices onto a Gigabit backbone. Ports 1 through 4 provide 10/100BASE-T/TX copper with integrated PHY, internal biasing and on-chip termination, which removes the external resistor dividers and termination networks that dominate the BOM of discrete copper PHY designs. Port 5 can be configured for RGMII, GMII, MII or RMII, so a single board layout can accept either an industrial application processor or a microcontroller host. Because the device is a managed Layer 2 switch, the host processor can read and write VLAN, QoS, port enable and mirroring registers over SPI or MIIM, which shortens commissioning time in a plant network.

🎥

IP Camera and Surveillance Network Node

An IP camera with several downstream sensors and a single uplink fits the KSZ8795CLXIC architecture exactly: four copper ports attach the camera, encoder and storage nodes while Port 5 carries video traffic upward at Gigabit speed. The 80-LQFP (10 x 10 mm) package keeps the switch footprint small enough for compact camera boards, and the 3.3 V single supply shares rails with typical video SoCs. Managed Layer 2 features let the system prioritize frames with QoS, and the port-mirror registers support remote diagnostics without extra instrumentation. On-chip termination means the board needs fewer passive parts beside each RJ-45 magnetic module, helping meet the tight cost and area budgets of volume surveillance designs.

🧩

Industrial IoT and Building Automation Node

Building automation controllers and industrial IoT edge nodes typically need several low-speed copper devices on one board and one fast link to a supervisory controller. The KSZ8795CLXIC assigns Ports 1 through 4 to sensors, actuators and HMI panels while Port 5 handles the uplink, and the configurable RGMII or RMII host interface matches both high-end and microcontroller-class processors. Managed Layer 2 forwarding with QoS prioritization keeps time-sensitive control traffic ahead of bulk data, and the MIIM/SPI management path lets the host apply VLAN segmentation between building floors. Low power consumption and on-chip biasing reduce both board area and the passive part count on space-constrained DIN-rail modules.

🌐

Consumer and Telecom Customer Premises Equipment

Customer premises equipment such as set-top boxes, home gateways and access terminals often needs to bridge several internal Ethernet PHY ports to an external network port. The KSZ8795CLXIC gives four 10/100Mbps internal copper ports and a configurable Gigabit uplink on a single 3.3 V device, keeping the bill of materials and board area low compared with using discrete PHY chips plus a separate switch. Internal biasing and on-chip termination remove resistor networks from every port, which shortens the analog design cycle and reduces EMC troubleshooting. Because the switch is managed, the host can enable or disable ports, set rate limits and mirror traffic for diagnostics, which supports remote fault isolation in deployed CPE installations.

🖥️

Embedded Linux SoC Network Interface

Embedded Linux boards frequently run an application processor with an RGMII interface and need to expose additional Ethernet ports for cameras, storage and debug links. The KSZ8795CLXIC lets the same silicon present a Gigabit RGMII uplink to the SoC while four 10/100 ports serve local peripherals, and the SPI management path gives the Linux driver direct register access for link configuration. The 10 x 10 mm 80-LQFP outline is compatible with the density of compact single-board computers, and the single 3.3 V rail matches typical SoC core supplies, simplifying power sequencing. Layer 2 management registers also let the driver implement bridging or VLAN tagging for multi-homed embedded systems.

⚡

PLC and Programmable Controller Communication Module

Programmable controller communication modules need a rugged, self-contained Ethernet interface that supports several devices on the same board and one uplink to the plant network. The KSZ8795CLXIC provides four 10/100Mbps copper ports with integrated PHY and on-chip termination plus a configurable GMII/RGMII/MII/RMII uplink, letting the module connect an Ethernet switch, an HMI and remote I/O while still reaching a Gigabit controller. Managed Layer 2 operation supports port mirroring for commissioning diagnostics, and the MIIM/SPI interface lets the PLC CPU read link and error counters without extra external hardware. The single 3.3 V supply and compact 80-LQFP footprint integrate cleanly into tightly budgeted control module boards.

What is the KSZ8795CLXIC?
The KSZ8795CLXIC is a Microchip Technology Layer 2 managed 5-port Ethernet switch with four 10/100Mbps copper ports and one 10/100/1000Mbps Gigabit uplink port. It integrates the PHYs, internal biasing and on-chip termination on chip, exposes GMII, RGMII, MII and RMII on the uplink port, and comes in an 80-LQFP (10 x 10 mm) package operating from 3.3 V. According to the Microchip product page for KSZ8795, it targets cost-sensitive designs needing four 10/100Mbps copper ports plus one Gigabit port.
What are the key specifications of KSZ8795CLXIC that engineers should know?
Key KSZ8795CLXIC specifications are: 5 total ports, 10/100Mbps on Ports 1 through 4, 10/100/1000Mbps on the Port 5 uplink, a configurable GMII/RGMII/MII/RMII host interface, MIIM and SPI management, 3.3 V supply, and an 80-LQFP (10 x 10 mm) package. The device is IEEE 802.3u compliant, uses internal biasing instead of external resistor networks, and integrates on-chip termination to reduce external component count and board area.
Which interfaces does the KSZ8795CLXIC uplink port support?
The Port 5 uplink of the KSZ8795CLXIC supports GMII, RGMII, MII and RMII, all configurable in the same package. The Microchip KSZ8795CLX Hardware Design Checklist confirms that uplink Port 5 carries the GMII/RGMII/MII/RMII configurable interface while Ports 1 to 4 are dedicated copper ports. This lets one PCB support either an RGMII-based application processor or an RMII-based microcontroller host.
Where can I download the KSZ8795CLXIC datasheet PDF?
The Microchip KSZ8795CLXIC datasheet is published by Microchip Technology as document 00002112B, titled Integrated 5-Port 10/100-Managed Ethernet Switch with Gigabit GMII/RGMII and MII/RMII Interfaces, and it runs 132 pages. You can obtain the PDF from the Microchip device document download, and a companion KSZ8795CLX Hardware Design Checklist (document 00003579B) is available from the same portal. Use the datasheet pin-description table when assigning PCB tracks.
Where do I find the KSZ8795CLXIC pinout?
The KSZ8795CLXIC uses an 80-LQFP package with 10 x 10 mm body, and the complete pin list is printed in the Microchip KSZ8795CLX datasheet (document 00002112B) and the KSZ8795CLX Hardware Design Checklist. The layout checklist also identifies the separate analog ground (GDNA) and digital ground (GNDD) pins, which must both be tied to one contiguous system ground plane. Use the manufacturer pin-description table to map the switch and PHY pins exactly.
What is the best drop-in replacement for KSZ8795CLXIC?
The closest drop-in replacement is the Microchip KSZ8765CLX, which Microchip describes as pin-compatible and offered in the same 80-pin LQFP package. Microchip's own support article states there are currently no drop-in replacement parts for KSZ8795CLXIC in the portfolio, and that KSZ8765CLX is the similar, same-package, pin-compatible option. The functional difference is the uplink: KSZ8765CLX is all 10/100Mbps, while KSZ8795CLX supports a 10/100/1000Mbps uplink.
KSZ8795CLXIC vs KSZ8765CLX - which is better for my design?
Choose the KSZ8795CLXIC when the uplink port must run 10/100/1000Mbps Gigabit, because it adds a Gigabit-capable uplink with GMII, RGMII, MII and RMII configurability that the KSZ8765CLX does not provide. Choose the KSZ8765CLX when every port can run at 10/100Mbps only, since it shares the same 80-pin LQFP footprint and is pin-compatible, letting you reuse existing layout and firmware. Both parts are managed Layer 2 switches with MIIM/SPI management.
When should I choose the KSZ8795CLXIC over the KSZ8765CLX?
Select the KSZ8795CLXIC when your system processor drives the switch over RGMII or GMII and you need a Gigabit uplink for trunking to a backbone switch, or when you need a copper port to auto-negotiate at 1000 Mbps. Select the KSZ8765CLX when all traffic is 10/100Mbps, when board cost dominates, or when you want a pin-compatible part with identical 80-LQFP layout for an existing design. Both are managed Layer 2 devices with SPI and MIIM control.
Is the KSZ8795CLXIC suitable for industrial applications?
Yes, the KSZ8795CLXIC is appropriate for industrial equipment because it integrates the copper PHYs, internal biasing and on-chip termination to reduce external component count, and it is offered in an industrial ordering code (IC suffix) supplied in a tray. The 80-LQFP (10 x 10 mm) package and 3.3 V single supply suit compact control modules. Microchip also publishes a dedicated KSZ8795CLX Hardware Design Checklist for industrial-style port implementations. Operating temperature limits are set in the datasheet.
What is the lead time and availability of the KSZ8795CLXIC?
The KSZ8795CLXIC is listed as active and stocked across multiple authorized channels, with deep inventory reported by distributors and a 10,000-piece quantity tier shown on aggregator listings. For a current quotation covering stock, minimum order quantity and delivery schedule for your specific volume, use the Request a Quote form on this page. Your distributor contact can confirm lead time against the exact ordering code, including the IC industrial suffix.
Where can I buy the KSZ8795CLXIC online?
The KSZ8795CLXIC can be ordered from authorized distributors that stock the Microchip 80-LQFP Ethernet switch, and it is also available through component sourcing houses. XAIPART handles quotations directly: submit the part number, target quantity and delivery destination through the Request a Quote form on this page, and you will receive current pricing, stock position and lead time for the exact KSZ8795CLXIC ordering code. Note that KSZ8795CLX and KSZ8795CLXIC denote different temperature/packaging suffixes.
Is the KSZ8795CLXIC the same as KSZ8795CLX?
The KSZ8795CLX and KSZ8795CLXIC are the same 80-LQFP Ethernet switch silicon; the trailing IC in KSZ8795CLXIC denotes the industrial-temperature, tray-packaged ordering code, while the base KSZ8795CLX is the temperature code without the IC packing suffix. Electrically they are equivalent for design purposes, so either can populate the same 10 x 10 mm footprint. Always confirm the suffix against your required temperature range and shipping format.
Can I replace the KSZ8795CLXIC with an equivalent from another manufacturer?
There is no directly pin-compatible third-manufacturer equivalent in the 80-LQFP footprint with the same GMII/RGMII/MII/RMII uplink and integrated copper PHYs. Cross-manufacturer parts in this class either use a different package, a different number of copper ports, or a digital-only uplink interface such as RGMII without integrated magnetics-side PHYs, so they require layout changes. The realistic path is the pin-compatible Microchip KSZ8765CLX in the same 80-LQFP package, accepting an all-10/100Mbps uplink.
What layout mistake causes frame drops on the KSZ8795CLXIC?
Frame drops on KSZ8795CLXIC designs are most often caused by splitting the analog and digital grounds. Although the device exposes separate GDNA and GNDD pins, Microchip states that both should be connected to a single solid, contiguous system ground plane rather than separate analog and digital ground regions. A fractured ground under the switch forces return current to detour, corrupting the MII/RMII timing between the switch and the host processor.
How does the KSZ8795CLXIC reduce external component count?
The KSZ8795CLXIC removes the usual discrete copper-port circuitry by integrating the 10/100BASE-T/TX PHYs, the bias resistor network and the port termination resistors on die. Instead of external resistor dividers and termination networks on each of Ports 1 through 4, the design uses internal biasing and on-chip termination, which lowers board area and part count. It still requires the isolation or magnetics components required for copper isolation at the connector, plus decoupling.
What are the key differences between the KSZ8795CLXIC and the KSZ8765CLX in power and management?
Both the KSZ8795CLXIC and the KSZ8765CLX are managed Layer 2 switches with MIIM and SPI host control and both use internal biasing with on-chip termination, so their management feature sets are broadly aligned. The practical difference is the uplink: the KSZ8795CLXIC Port 5 supports 10/100/1000Mbps with GMII/RGMII/MII/RMII configurability, whereas the KSZ8765CLX uplink is 10/100Mbps. Current consumption is correspondingly higher for the KSZ8795CLXIC when the Gigabit PHY is active.

Impormasyon ng Talumpati sa Engineering for KSZ8795CLXIC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the KSZ8795CLXIC when your product needs four 10/100Mbps copper ports plus one uplink that must run at Gigabit, or when the host processor drives the uplink over RGMII or GMII at 1.25 GB/s. It is the right pick for industrial gateways, IP cameras, IoT nodes and CPE, where integrated biasing, on-chip termination and a managed Layer 2 feature set simplify the analog design and shorten board bring-up. Choose the KSZ8765CLX or KSZ8765CLXIC when every port can operate at 10/100Mbps, since they are pin-compatible in the same 80-LQFP package and allow direct layout reuse with lower cost. Choose the base KSZ8795CLX when you need the same silicon under a non-IC ordering code. No third-manufacturer part is pin-compatible in this footprint, so a cross-brand change means a new PCB.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto KSZ8765CLX KSZ8765CLXIC KSZ8795CLX
Package 80-LQFP (10 x 10 mm) 80-LQFP (10 x 10 mm) - same 80-LQFP (10 x 10 mm) - same 80-LQFP (10 x 10 mm) - same
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Total Port Count 5 5 5 5
Copper Port Speed (Ports 1-4) 10/100 Mbps 10/100 Mbps 10/100 Mbps 10/100 Mbps
Uplink Port Speed (Port 5) 10/100/1000 Mbps 10/100 Mbps (no Gigabit uplink) 10/100 Mbps (no Gigabit uplink) 10/100/1000 Mbps
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Integrated Biasing and Termination Yes, internal biasing with on-chip termination Yes Yes Yes
Pin Compatibility Reference design Pin-compatible, same 80-pin LQFP package Pin-compatible, same 80-pin LQFP package Identical silicon and footprint

Pangunahing mga Pagkakaiba

  • Gigabit-capable uplink in the same 80-LQFP footprint (kumpara saKSZ8765CLX)
  • Higher integration reduces external passive count (kumpara saKSZ8765CLXIC)
  • Single-part 5-port managed switch with host-side flexibility (kumpara saKSZ8795CLX)

Talaan ng Disenyo

Tie GDNA and GNDD together into a single solid, contiguous system ground plane. Microchip explicitly warns that separate analog and digital ground regions cause frame drops on KSZ8795CLX designs because the return current must then find a path between the two domains under the device. Route the copper port differential pairs as short, tightly coupled traces with a continuous ground reference directly beneath them, and place the isolation magnetics close to the RJ-45 connectors to minimize radiated emissions.

Follow the KSZ8795CLX Hardware Design Checklist (document 00003579B) for new boards. The switch already integrates internal biasing and on-chip termination, so do not add external bias resistor dividers or termination networks on Ports 1 to 4. Provide the standard decoupling close to the 3.3 V supply pins, and keep the RGMII/GMII clock and data routing short and impedance controlled because the uplink runs at 1.25 GB/s in RGMII mode, where setup and hold margins are tight.

Estimated: with a 3.3 V supply and a full 100 Mbps load on all five ports, the switch dissipation scales with port activity; allow for roughly 1 W to 2 W of internal consumption in the worst case, which means the 80-LQFP package needs a solid copper pour and, in a sealed enclosure, careful attention to ambient rise. Estimate your own figure from the measured per-port current in the datasheet operating tables multiplied by the number of active ports, then verify junction temperature against the maximum rating in the device documentation.

The Port 5 uplink is configurable, so fix the host interface mode in software before layout sign-off, because GMII, RGMII, MII and RMII use different clock and data topologies. RGMII requires a 1.25 GB/s interface with source-synchronous clocking and careful trace length matching between the clock and data pairs; RMII uses a slower 50 MHz reference clock with a narrower timing budget. Confirm the selected mode and the corresponding host-side PHY or SoC timing in the datasheet before finalizing the layout.

Do not assume the base KSZ8795CLX and KSZ8795CLXIC are interchangeable without checking the temperature code and shipping format, since the IC suffix denotes the industrial tray ordering code. Likewise, verify that the link partner on each copper port supports auto-MDIX before relying on it, and confirm that the uplink speed negotiation on Port 5 is enabled in the boot configuration. Finally, remember that Microchip states there is currently no exact drop-in replacement for this device in the portfolio, so plan availability around the pin-compatible KSZ8765CLX family.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

RoHS compliant status is shown on aggregator part listings for KSZ8795CLXIC. The IC ordering suffix denotes the industrial temperature grade; automotive AEC-Q100 qualification is not indicated for this Ethernet switch.

Data napatotohanan sa: 2026-11-14 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

ksz8795clx datasheet KSZ8795CLXIC datasheet PDF KSZ8795CLXIC pinout KSZ8795CLXIC 80-LQFP footprint KSZ8795CLXIC 5-port 10/100 switch KSZ8795CLXIC RGMII uplink KSZ8795CLXIC vs KSZ8765CLX KSZ8795CLXIC drop-in replacement KSZ8795CLXIC price and stock Microchip KSZ8795CLXIC Ethernet switch KSZ8795CLX hardware design checklist KSZ8795CLX ground layout frame drop KSZ8795CLXIC industrial gateway use case what is the difference between KSZ8795CLX and KSZ8795CLXIC

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology KSZ8795CLXIC KSZ8795CLX KSZ8765CLX Ethernet switch Layer 2 managed switch 10/100BASE-T/TX PHY 10/100/1000BASE-T Gigabit uplink GMII RGMII MII RMII MIIM management interface SPI host interface IEEE 802.3u auto-MDIX internal biasing on-chip termination 80-LQFP package LQFP family surface mount technology RoHS AEC-Q100 industrial IoT gateway IP camera network node
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ