Mga Produkto (46,000+)

LM2903AVQPWRQ1 - Dual 36 V Automotive Comparator | TI
LM2903AVQPWRQ1

LM2903AVQPWRQ1 - Dual 36 V Automotive Comparator | TI

Texas Instruments LM2903AVQPWRQ1 is an AEC-Q100 Grade 0 and 1 automotive dual differential comparator with a 2 V to 36 V single-supply range, open-collector outputs, and an 8-pin TSSOP (PW) package. It provides two independent comparison channels, a typical response time of 1.3 us, and rail-to-rail input operation for flexible signal-threshold detection. A comparator is a high-gain analog circuit that determines whether one input voltage is above or below another input voltage. Its output changes state when the differential input crosses the selected threshold. The dual differential comparator category extends this function to two independent channels, making it useful for battery monitoring, sensing, window detection, and control loops. In the hierarchy of semiconductor components, a comparator belongs to the broader analog and interface IC family. The LM2903AVQPWRQ1 combines a wide operating supply range with low supply-current operation. Manufacturer product information identifies the device as an automotive high-voltage dual comparator qualified for AEC-Q100 Grade 0 and 1. Each channel uses an open-collector output, allowing multiple comparators to share a pull-up network for wired-AND signaling. The typical propagation delay is 1.3 us, while the operating temperature range extends from -40 C to +125 C. Each comparator channel includes a non-inverting input, an inverting input, and an open-collector output. The eight-pin TSSOP package keeps the two channels separate while supporting compact PCB placement. Because open-collector outputs require an external pull-up resistor, the output voltage is set by the pull-up supply and resistor rather than by a push-pull output stage. The dual architecture also allows one device to monitor two independent threshold conditions. Typical uses include automotive battery and power-rail monitoring, industrial threshold detection, sensor conditioning, overvoltage and undervoltage protection, and automotive control modules. The 2 V to 36 V operating range is particularly useful when a circuit operates from an automotive battery-derived supply. The 1.3 us response time supports comparisons where the threshold result must be captured quickly, although propagation delay and input overdrive should be checked against the system timing budget. When designing a PCB for LM2903AVQPWRQ1, place the device near the sensed signals and keep input traces short to reduce noise pickup. Route each open-collector output with an appropriate pull-up resistor, verify absolute-maximum input and supply voltages, and account for input bias current when choosing high-impedance divider networks. The automotive-qualified grade and -40 C to +125 C rating support harsh-temperature systems, provided the surrounding power distribution and protection components are appropriately rated. This product page consolidates the exact ordering information, package details, technical specifications, drop-in alternatives, and application-specific design guidance for engineers evaluating the LM2903AVQPWRQ1. It also distinguishes true same-package drop-in choices from related comparators that require a different footprint.

RFQ Kontak
LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments
LM2903BIDDFR

LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903BIDDFR is a dual industrial-grade standard comparator with two independent comparison channels, open-collector outputs, and rail-to-rail input capability. It is packaged in an 8-pin SOT-23-THN (DDF) surface-mount package and is specified for an operating temperature range of -40°C to 125°C. A comparator is an analog semiconductor that compares two input voltages and produces a logic-level result indicating which input is higher. A dual comparator integrates two comparison channels into one package, allowing simultaneous sensing, threshold detection, or window monitoring. Within the broader hierarchy, the LM2903B belongs to the comparator and amplifier IC family and ultimately to the wider semiconductor and signal-conditioning market. The LM2903BIDDFR combines an open-collector output stage with a differential-input architecture. Open-collector outputs can pull a logic node low when the comparator changes state, while an external pull-up resistor establishes the high state. This arrangement provides flexible interface voltage selection and is useful with TTL, MOS, and CMOS-compatible loads. Each channel supports independently routed non-inverting and inverting inputs. The B-version product family provides improved characteristics relative to earlier LM2903, LM293, and LM393 variants while maintaining pin-for-pin drop-in compatibility. The manufacturer identifies LM2903B as a drop-in replacement for the earlier devices, and its common-mode input range includes ground. These features make the comparator suitable for systems that compare bipolar or single-ended sensor signals without requiring a fully differential amplifier. Typical applications include industrial control systems, automatic test equipment, power-supply supervision, motor-control circuits, window comparators, and general threshold detection. The dual-channel configuration can implement two independent safety thresholds, compare upper and lower limits, or monitor complementary sensor outputs without requiring two separate comparator packages. The primary design consideration is the open-collector output: each output requires an appropriate pull-up resistor and must remain compatible with the voltage and timing requirements of the connected logic circuit. Input polarity, output state, and propagation behavior should be checked against the specific logic levels and system timing before production release. This page combines the exact ordering information, package details, operating limits, application guidance, and design considerations for the LM2903BIDDFR. It also organizes sourcing questions and replacement guidance around the device's actual dual-comparator function and open-collector interface.

RFQ Kontak
LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments
LM2903BIDGKR

LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments

Texas Instruments LM2903BIDGKR is a dual differential comparator with two independent channels, a maximum rated supply voltage of 38 V, open-collector outputs, and an 8-VSSOP package. It operates from a 2 V to 36 V supply, supports input common-mode and differential voltages up to ±38 V, and is specified as a rail-to-rail input device with 0.37 mV input offset voltage. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a threshold. The LM2903B belongs to the comparator hierarchy within analog and power-management semiconductors. Unlike an operational amplifier, each channel does not require feedback compensation for linear amplification, and its open-collector output must connect to an external pull-up resistor when driving a logic input. Key B-version improvements include lower offset voltage, lower input bias current, lower supply current, faster response, and stronger input protection than the original LM2903. The device features 0.37 mV input offset voltage, 3.5 nA input bias current, 200 μA supply current per comparator, 1 μs response time, and a 2 kV human-body-model ESD rating. Its outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer documentation. Each internal comparator is electrically independent, but both channels share the supply pins and ground connection. Separate input and output pins allow one channel to perform threshold detection while the other performs window monitoring, current sensing, or another independent comparison. The open-collector architecture provides wired-AND behavior when multiple outputs share a pull-up node, although rise time then depends on the resistor, capacitance, and leakage current. Typical uses include industrial sensor thresholding, battery and power-supply monitoring, overvoltage detection, signal conditioning, and embedded control systems. The wide 38 V maximum rating is useful in industrial environments where input transients can exceed nominal logic levels, but system designers must still validate signal levels and protection requirements for every operating condition. For layout, route the comparator inputs away from switching nodes and place input-referred components close to their associated pins. Select the external output pull-up to balance sink-current capability against rise time. Verify input common-mode range, output pull-up voltage, package thermal conditions, and system shutdown behavior against the manufacturer datasheet before production release. This page combines the LM2903B electrical characteristics, package and pin information, application guidance, design checks, and verified drop-in alternatives. It also highlights practical considerations for pull-up selection, input protection, noise, and industrial qualification that engineers can apply directly during schematic review and PCB design.

RFQ Kontak
LM2903BIDR - Dual 36V Open-Collector Comparator | Texas Instruments
LM2903BIDR

LM2903BIDR - Dual 36V Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903BIDR is a dual industrial-grade differential comparator with two independent channels, a maximum supply rating of 36 V, open-collector outputs, and a 1 µs response time. It is supplied in an 8-pin SOIC (D) package and is specified for operation from -40 °C to +125 °C. The B-version family also provides a low 0.37 mV input offset, 3.5 nA input bias current, and 200 µA supply current per comparator. A comparator is an analog integrated circuit that determines whether one input voltage is above or below another and switches its output when the differential input crosses a threshold. In the broader semiconductor hierarchy, a comparator belongs to the amplifier and comparator IC family rather than an operational amplifier. Open-collector outputs are useful when multiple devices must share a wired bus or when an external pull-up resistor selects the logic voltage independently of the comparator supply. The LM2903BIDR supports single- or dual-supply operation, allowing its input and output signals to be referenced around ground in control, sensing, and protection circuits. Its industrial temperature range makes it suitable for equipment operating beyond consumer-temperature limits. The two channels are independent, so one device can perform two threshold functions while sharing a package, although output pull-up components and supply decoupling remain external. Verified distributor and manufacturer results identify the device as a standard, general-purpose, rail-to-rail-input comparator with open-collector outputs and an 8-SOIC footprint. Texas Instruments describes the B-version as a next-generation member of the LM393 and LM2903 families, emphasizing lower offset, lower bias current, lower supply current, faster response, wider supply capability, and improved ESD robustness. Typical applications include DC overvoltage monitoring, industrial sensor thresholds, battery-powered indication, window comparators, and relay or alarm activation. Because an open-collector output does not actively drive a high voltage, every application must provide a suitable pull-up resistor and account for its sink-current limit. The collector voltage and supply limits should be checked against the manufacturer datasheet before designing to absolute maximum conditions. For PCB design, place input resistors close to the relevant pins, decouple the supply close to the device, and route high-impedance input traces away from switching nodes. Where open-collector outputs drive cables or long PCB traces, use a strong pull-up and consider a buffer if additional noise immunity or edge control is required. This page combines verified manufacturer and distributor details with engineering guidance for selecting, sourcing, and replacing the component.

RFQ Kontak
LM2903BIDSGR - Dual 38V Comparator | Texas Instruments
LM2903BIDSGR

LM2903BIDSGR - Dual 38V Comparator | Texas Instruments

Texas Instruments LM2903BIDSGR is a dual differential analog comparator with a maximum rating of 38 V, open-collector outputs, and an 8-WSON package measuring 2 x 2 mm. Each channel supports rail-to-rail input behavior, while the device uses 200 uA of supply current per comparator and has a typical response time of 1 us. The B-version combines low power consumption with improved switching performance. An analog comparator is a semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. Comparators belong to the broader analog IC hierarchy alongside amplifiers, voltage references, and data converters. They are used to implement threshold detection, sensing, overvoltage protection, oscillator functions, and digital-interface conditioning when open-collector outputs are advantageous. The LM2903B family provides a maximum input rating of 38 V, an input offset voltage as low as 0.37 mV, and an input bias current as low as 3.5 nA. Its open-collector output stages can sink output current and support pull-up connections to the system supply, allowing the device to interface with TTL, MOS, and CMOS logic. Dedicated input ESD clamps provide an HBM ESD rating of 2 kV. The B-version improves the original LM2903 family through lower offset voltage, lower input bias current, lower supply current, faster response, wider supply capability, and improved input ruggedness. Its common-mode input voltage range includes ground, which supports sensing around a zero-volt reference when the supply conditions permit operation near that boundary. The 1 us response time also makes the device suitable for faster control loops than classic general-purpose comparators. Typical uses include DC overvoltage and undervoltage detection, sensor threshold interfaces, battery and power-supply monitoring, window comparators, relaxation oscillators, and industrial control logic interfaces. The compact 2 x 2 mm WSON package helps reduce board area where dense analog and mixed-signal layouts are required. Designers should preserve adequate input and output separation when operating near absolute maximum limits, place pull-up resistors close to each open-collector output, and route sensitive input traces away from switching nodes. The exposed thermal pad should be connected to the ground plane according to the package land pattern and thermal design guidance. This page combines the LM2903BIDSGR electrical characteristics, package and lifecycle information, replacement assessment, comparison data, and practical PCB guidance to help engineers evaluate the device quickly and design a robust comparator circuit.

RFQ Kontak
LM2903BIPWR - Dual 36V Comparator | Texas Instruments
LM2903BIPWR

LM2903BIPWR - Dual 36V Comparator | Texas Instruments

The Texas Instruments LM2903BIPWR is a dual industrial-grade comparator with a 2 V to 36 V supply range, 1 µs response time, and open-collector outputs in an 8-pin TSSOP package. Each channel provides an independent comparison function, with input offset voltage as low as 0.37 mV and input bias current as low as 3.5 nA. The device is designed for robust threshold detection, industrial signal conditioning, and systems powered from higher-voltage rails. A voltage comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903B belongs to the comparator hierarchy, where it functions as a general-purpose comparator, analog signal interface, and power-management building block. Its two channels can monitor independent sensors or participate in window-detection and overvoltage-protection circuits. Open-collector outputs also make wired-AND behavior possible when multiple comparators share a pull-up resistor. The B-version improvements include a maximum supply rating of 38 V, a 2 kV human-body-model ESD rating, low input offset, low input bias current, and supply current of 200 µA per comparator. The 1 µs response time supports faster decision-making than legacy comparators, while the rail-to-rail input characteristic permits operation from the ground rail to the positive supply rail. The industrial temperature range covers applications from -40 °C to +125 °C. Each output uses an open-drain transistor rather than a push-pull output stage. This architecture provides flexible voltage-level compatibility because an external pull-up resistor determines the output voltage. It also permits several outputs to be connected together when the resulting wired-AND behavior is intentional. A pull-up resistor is required even when only one output is used; without it, the output cannot rise to a valid high state. Typical uses include industrial sensor interfaces, battery threshold detection, motor and actuator protection, window comparators, relay-control logic, and power-supply monitoring. The 36 V operating range is useful in industrial systems where the comparator may directly observe a protected signal node. The low 200 µA per-comparator supply current also makes the device suitable for low-power monitoring when the signal source can be brought close to the supply rail. For reliable layout, route each comparison input directly to its device pin and keep feedback or output loops away from the input traces. Place the output pull-up resistor close to the open-collector output, and use a local supply bypass capacitor where the power rail can produce disturbance. Account for input common-mode voltage and output leakage when designing the system threshold. This page combines the Texas Instruments ordering information, device specifications, package details, pin assignments, sourcing workflow, and practical replacement guidance to support faster component selection and PCB design. Use the manufacturer datasheet for the complete electrical characteristics, timing definitions, and application guidance.

RFQ Kontak
LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments
LM2903BQDRQ1

LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments

Texas Instruments LM2903BQDRQ1 is an automotive dual differential comparator with two open-collector outputs, rail-to-rail input operation, and a supply range of ±18 V or 36 V total. It is packaged in an 8-pin SOIC (D) and rated for operation from -40 °C to +125 °C. The device is identified by Texas Instruments as an AEC-Q100 automotive-grade option within the LM2903B-Q1 family. A comparator is an analog signal-processing IC that compares two input voltages and produces a digital output indicating which input is higher. Comparators belong to the broader amplifier IC category and are commonly used as threshold detectors, sensor interfaces, overvoltage monitors, and control-loop decision elements. Unlike a general-purpose operational amplifier, the LM2903BQDRQ1 is intended primarily for open-loop voltage comparison rather than precision closed-loop amplification. The primary features of the LM2903BQDRQ1 are its dual differential input architecture, open-collector output stage, rail-to-rail input capability, and broad supply-voltage range. The open-collector outputs require an external pull-up resistor, allowing the output state to be set by the external pull-up voltage. This arrangement is useful when interfacing with automotive logic, transistor-based level conversion, relay drivers, or multiple devices sharing a wired bus. Its -40 °C to +125 °C temperature range supports applications across industrial, automotive, and other extended-temperature environments. The LM2903B-Q1 family is described by Texas Instruments as a next-generation version of the industry-standard LM2903-Q1 comparator family. Its stated improvements include lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance, together with drop-in replacement convenience. The target MPN combines these automotive-grade features in the 8-SOIC package identified by ordering code D. Typical uses include battery-pack threshold detection, automotive sensor conditioning, overvoltage and undervoltage protection, industrial control inputs, window or level monitoring, and logic-level translation. In each case, the two comparator channels can monitor independent thresholds or operate as complementary detectors. The open-collector architecture also permits a system designer to select the pull-up voltage and current rather than being restricted to a fixed push-pull output voltage. When laying out a board, place the pull-up resistor close to the open-collector output and keep comparator input traces short to reduce susceptibility to injected noise. Confirm output-current limits, input common-mode behavior, supply sequencing, and logic thresholds in the manufacturer datasheet before finalizing the design. Consider a device with push-pull outputs when an external pull-up is undesirable, or verify an alternate comparator carefully when its output architecture or input range differs. This page combines the manufacturer’s automotive comparator information, verified ordering details, and practical drop-in guidance. It helps engineers identify the correct package, temperature grade, output type, and replacement options while emphasizing the electrical checks that matter during schematic and PCB design.

RFQ Kontak
LM2903BQPWRQ1 - Dual Automotive Comparator | Texas Instruments
LM2903BQPWRQ1

LM2903BQPWRQ1 - Dual Automotive Comparator | Texas Instruments

Texas Instruments LM2903BQPWRQ1 is an automotive dual differential comparator with two independent open-collector outputs, rail-to-rail input capability, and operation across single or dual supply rails up to 36 V. It is packaged in an 8-pin TSSOP tape-and-reel configuration. The LM2903B-Q1 family is positioned as the next generation of the automotive LM2903-Q1 comparator line, combining cost-conscious design with lower offset voltage, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance. A comparator is an analog semiconductor that evaluates two input voltages and produces a logic-level indication of their relationship. The differential input stage determines whether the non-inverting input is above or below the inverting input, while the open-collector output stage provides a flexible interface for pull-up resistors and digital logic. In the LM2903BQPWRQ1, the dual-channel architecture provides two independent comparator functions in one package, reducing board area when two sensing channels are required. Key advantages include rail-to-rail input operation, a common-mode input range that includes ground, an operating supply range extending to 36 V, and open-collector outputs that can sink current from an external pull-up. The open-collector architecture is particularly useful when interfacing to TTL, CMOS, or MOS logic, or when multiple open-drain outputs need to share a bus with suitable wired-AND behavior. Automotive qualification supports its use in cost-sensitive vehicle electronics where tolerance for electrical transients and ESD events is important. The LM2903B-Q1 generation improves several parameters relative to the earlier LM2903-Q1 family while retaining compatibility with established LM2903-family applications. Its lower offset voltage supports more accurate switching thresholds, while reduced supply and input bias currents can simplify power budgeting and high-impedance sensor interfaces. Lower propagation delay is useful in control loops and threshold-detection circuits, and the improved 2 kV ESD capability strengthens robustness at exposed connector and signal interfaces. Typical uses include automotive battery and power-system monitoring, sensor threshold conditioning, overvoltage and undervoltage detection, window comparison, industrial control logic, and dual-level signal qualification. Because the outputs are open collector, the design must include suitable pull-up resistors when a valid high output is required. Inputs must also remain within the device's absolute maximum ratings, and unused channels require appropriate input states to prevent unstable output behavior. Designers should verify the exact input common-mode range, differential input limits, output pull-up voltage, and timing budget against the manufacturer datasheet for the selected operating condition. Automotive systems should additionally check the required qualification, temperature grade, ESD class, and production test requirements. This page combines exact catalog information, package details, drop-in alternatives, and application-specific engineering guidance for faster component selection and PCB planning.

RFQ Kontak
LM2903D - Dual Open-Collector Comparator | Texas Instruments
LM2903D

LM2903D - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903D is a dual differential analog comparator with two independent comparator channels, an operating supply range of 2 V to 36 V, a response time of 300 ns, and an 8-pin SOIC package. Each channel provides open-collector output behavior for level translation, relay driving, and wired-AND logic functions. The device is specified for operation from -40 °C to +125 °C according to the available manufacturer comparison data. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2903D belongs to the comparator hierarchy within analog and mixed-signal semiconductors, providing a simple alternative to an operational amplifier configured as a comparator. Its two channels operate independently, allowing one package to implement two threshold decisions or to control complementary functions in a single circuit. The open-collector outputs are a defining electrical feature. Each output transistor can pull its output low, but it cannot actively drive the output high, so an external pull-up resistor is required. Multiple open-collector outputs can share one pull-up to create a wired-AND arrangement. This architecture also provides a useful form of output isolation while remaining compatible with standard 5 V and 3.3 V digital logic levels when the pull-up rail is selected appropriately. The 2 V to 36 V supply capability allows operation from low-voltage analog systems through conventional industrial control rails. Its 300 ns response time supports applications where decisions must be made faster than typical slow comparators but where nanosecond-level precision is unnecessary. The operating temperature range covers industrial environments, although production designs should still verify temperature-dependent input offset, output-current, and propagation-delay behavior using the selected manufacturer's complete datasheet. Typical uses include industrial sensor conditioning, battery monitoring, overvoltage detection, window or level comparators, relay and solenoid interfaces, and digital control systems that require open-collector outputs. The SOIC-8 package is also appropriate for through-hole-style PCB assembly and manual rework, although SOIC-8 is larger than modern comparator packages such as SOT-23 and MSOP-8 variants. When designing with the LM2903D, always place the input and pull-up networks close to their associated pins, and account for input common-mode limits at the selected supply voltage. A pull-up resistor is not optional because the open-collector output cannot source current. Reviewing the voltage drop across the pull-up and the output transistor's current rating is essential when several outputs share the same node. This page consolidates verified distributor listings, manufacturer references, pin-compatible alternatives, package details, and practical circuit guidance. It also distinguishes directly interchangeable devices from higher-speed or higher-precision alternatives whose electrical behavior may require different design assumptions.

RFQ Kontak
LM2903DE4 - Dual 36V Open-Collector Comparator | Texas Instruments
LM2903DE4

LM2903DE4 - Dual 36V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DE4 is a dual differential comparator built for general-purpose signal conditioning and threshold detection. The device contains two independent comparators, supports a 2 V to 36 V single-supply operating range, and provides open-collector outputs in an 8-pin SOIC package. Its 300 ns response time makes it suitable for systems that require faster decisions than the related LM393B family while retaining the familiar open-collector interface. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. Within the broader hierarchy of interface ICs, comparators extend analog signal conditioning into threshold control, protection, sensing, and discrete logic activation. The LM2903DE4 is specifically a dual differential comparator: each half can independently compare an inverting input with a non-inverting input while sharing common supply and ground connections. The principal features include two independent channels, a 2 V to 36 V supply range, an approximately 300 ns response time, and open-collector outputs compatible with TTL, MOS, and CMOS circuits. The common-mode input range includes ground, and the differential input range is equal to the maximum-rated supply voltage of ±38 V for the family. Each output can sink external current while remaining in a high-impedance state when inactive, requiring an external pull-up resistor for normal logic-high operation. Differential comparison is especially useful when a sensor or signal source is referenced to another voltage rather than to ground. By placing the threshold on the non-inverting input and the sensed signal on the inverting input, the comparator can provide overvoltage, undervoltage, temperature, current, or level detection. Because the channels are independent, the same package can implement two thresholds, compare two unrelated signals, or combine two decisions locally. Typical applications include industrial sensor interfaces, overvoltage and reverse-polarity protection, window comparators, motor and relay control, power-supply supervision, and embedded control systems. The open-collector outputs are particularly useful for wired-AND arrangements, relay-driver interfaces, and level translation because the output stage can remain disconnected while an external pull-up establishes the logic-high voltage. The principal design consideration is the open-collector output. Place each pull-up resistor close to the relevant output and select it to balance rise time against sink-current demand. Also check input common-mode limits, supply operating range, output leakage, and the timing relationship between the reference voltage and sensed signal before using the comparator for high-speed pulse detection. This page consolidates the manufacturer specifications, package and pin information, orderable alternatives, comparison data, and practical application guidance into a design-focused reference for engineers evaluating the LM2903DE4.

RFQ Kontak
LM2903DG - Dual Comparator, 2-36V, SOIC-8 | onsemi
LM2903DG

LM2903DG - Dual Comparator, 2-36V, SOIC-8 | onsemi

The onsemi LM2903DG is a dual differential voltage comparator with open-collector outputs, low input offset voltage of 2 mV typical, and a wide supply voltage range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), housed in an 8-pin SOIC package rated from -40C to +105C. A voltage comparator is an analog IC that compares two input voltages and outputs a digital signal indicating which input is higher. It sits at the boundary between the analog and digital domains within the signal-chain hierarchy: comparator -> analog front-end IC -> signal conditioning -> power/semiconductor. The LM2903 family, originally introduced as the LM393 series, is the industry-standard general-purpose comparator, and the LM2903 variant extends the temperature range for industrial use. Key features include two independent comparators in one package, open-collector outputs that support rail-to-rail output swings and wired-OR configurations, a common-mode input range that extends down to ground (negative rail) during single-supply operation, and a very low supply-current drain of approximately 0.4 mA per comparator that is largely independent of supply voltage. Input offset voltage as low as 2 mV makes the device suitable for precision threshold detection. Technically, the device permits single- or split-supply operation as long as the difference between the two supplies is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. Typical propagation delay (response time) is approximately 1.3 us, adequate for threshold detection, level shifting, and slow-to-medium speed switching tasks. The open-collector stage requires an external pull-up resistor to define the logic-high level, allowing direct interfacing to 5V, 3.3V, or other logic families. Typical applications include limit comparators and over-voltage/under-voltage detectors in power supplies, window comparators in battery-management and industrial monitoring circuits, zero-crossing detection, oscillator and pulse-generator timing circuits, and logic-level translation in automotive and industrial controllers where the -40C to +105C range is required. When designing with the LM2903DG, add hysteresis (a small positive-feedback resistor around the comparator) to prevent output chatter near slowly changing input thresholds, and place a pull-up resistor of 1k to 100k on each output. This page consolidates distributor availability data, pin-compatible drop-in alternatives from multiple manufacturers, and practical design notes that go beyond the manufacturer datasheet alone.

RFQ Kontak
LM2903DG4 - Dual Open-Collector Comparator | Texas Instruments
LM2903DG4

LM2903DG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903DG4 is a dual differential comparator containing two independent comparator channels, an open-collector output configuration, and an 8-pin SOIC package. The device supports single-supply or dual-supply operation, with a maximum-rated supply voltage of 32 V and a tested differential input voltage of 30 V. Its low supply-current drain of 0.4 mA typical per comparator is independent of supply voltage, making it suitable for power-conscious industrial and embedded systems. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. The LM2903 is a dual differential comparator, placing two independent comparator channels in one package. Within the broader semiconductor hierarchy, it is a comparator, analog IC, and interface/amplifier-class signal-conditioning component used to translate small analog voltage relationships into logic-compatible decisions. Each LM2903 channel supports operation from a single supply or from dual supplies. The open-collector outputs can sink output current while presenting a high-impedance state when the output is inactive. According to the Texas Instruments LM2903 product information, the outputs are compatible with TTL, MOS, and CMOS logic. This makes the device useful when an external pull-up resistor is required to establish the inactive output voltage. The two channels are electrically independent, allowing one comparator to monitor a control threshold while the other handles a second signal, alarm, or protection event. Common-mode input voltage range includes ground, and the differential input rating equals the maximum-rated supply voltage. These characteristics support sensing arrangements in which signals may approach the lower supply rail, subject to the limits stated in the manufacturer datasheet. Typical applications include overvoltage and undervoltage detection, industrial sensor interfaces, battery monitoring, window or threshold detection, relay-control logic, and general-purpose signal conditioning. The wide supply range also makes the device useful in 5 V, 12 V, and 24 V industrial systems when the relevant operating limits are observed. Designers should account for open-collector pull-up requirements, input common-mode limits, output sink-current capability, and unused-channel handling. A pull-up resistor must be selected to establish a valid logic-high voltage without exceeding the device's output-current limits. Input filtering may also be required when noisy signals could cause repeated transitions near the comparison threshold. This page combines manufacturer identification, package details, cross-reference information, and engineering guidance for threshold detection and open-collector interface design. It also highlights the operating conditions that should be checked before using a substitute or family variant on an existing board.

RFQ Kontak
LM2903DGKR - Dual Open-Collector Comparator | Texas Instruments
LM2903DGKR

LM2903DGKR - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DGKR is a dual differential comparator with two independent comparison channels, open-collector outputs, and rail-to-rail input capability in an 8-pin VSSOP package. The device operates from 2 V to 36 V, supports common-mode input voltages from -1 V to +18 V, and has a typical response time of 1.3 microseconds. It is intended for general-purpose voltage comparison, threshold detection, and interface applications. A comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. In the broader semiconductor hierarchy, LM2903 belongs to the comparator and linear IC family, where it bridges analog signal sensing and digital control. Each LM2903 channel combines a differential input pair with an open-collector output, allowing the output stage to pull a logic rail low when the comparison state requires it. The LM2903DGKR provides two channels in one package, reducing board area compared with separate single comparators. Its open-collector outputs support wired-AND behavior when multiple channels pull a shared bus low, while external pull-up resistors establish the high logic voltage. Rail-to-rail input capability extends the usable common-mode range toward the supply rails, which is useful in battery-powered and low-voltage systems. Its stated 1.3-microsecond response time supports general-purpose detection rather than high-speed timing applications. The operating range of 2 V to 36 V makes the device suitable for low-voltage control circuits and higher-voltage industrial systems. Common-mode operation from -1 V to +18 V permits signal sensing beyond the lower supply rail. Each output remains electrically open at the collector, so designers can select pull-up voltage, interface to open-drain logic, or connect several outputs to a shared bus. The 8-pin VSSOP package supports compact surface-mount layouts but requires careful handling because its lead pitch is narrower than that of standard SOIC packages. Typical uses include DC overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control inputs, battery monitoring, and open-drain logic interfacing. In each case, resistor values should be chosen from the applied input range, output pull-up requirement, output leakage, and permissible sink current rather than from a single fixed rule. When laying out an LM2903DGKR circuit, place input and output components close to their associated pins and keep switching-current paths away from the differential inputs. Add a local supply bypass capacitor to limit transient coupling into the comparison threshold. The open-collector output also requires a pull-up resistor in every configuration where a valid high output is required. This product record combines the manufacturer ordering information, package and functional characteristics, verified replacement candidates, and practical layout guidance. It is intended to help engineers evaluate LM2903DGKR for open-collector comparator designs while accounting for voltage range, response time, channel count, and board-space constraints.

RFQ Kontak
LM2903DGKRG4 - 36V Dual Comparator | Texas Instruments
LM2903DGKRG4

LM2903DGKRG4 - 36V Dual Comparator | Texas Instruments

Texas Instruments LM2903DGKRG4 is a dual differential comparator containing two independent voltage comparators, with a 2 V to 36 V supply range, approximately 300 ns response time, and an 8-pin VSSOP package. Both channels use open-collector outputs, allowing wired logic or use with an external pull-up resistor. The part supports single-supply operation and dual-supply operation when the total supply span is 2 V to 36 V. A voltage comparator is an analog interface that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy, where a comparator is an analog IC used for threshold detection, signal conditioning, and protection. Its two independent channels can monitor separate control, sensing, or feedback signals, while its open-collector architecture provides flexible interface voltage selection. The principal operating characteristics include a 2 V to 36 V supply range, approximately 300 ns propagation delay, and low supply-current drain of 0.4 mA typical per comparator. Its rail-to-rail input capability allows the input common-mode range to extend toward the supply rails. Open-collector outputs can sink output current while leaving the effective pull-up voltage under the system designer’s control, making the device useful in wired-AND, wired-OR, and level-shifting arrangements. Each channel has one inverting input, one non-inverting input, one output, and access to the supply and ground rails. Because the two comparators are independent, each channel can be configured for a different threshold or polarity. Input offset, input bias current, output saturation characteristics, and detailed common-mode behavior should be checked against the manufacturer datasheet for each operating condition, particularly when sensing near a supply rail. Typical uses include industrial control systems, battery-powered equipment, power-supply sequencing, overvoltage and undervoltage monitoring, sensor-threshold conditioning, and general-purpose logic interfaces. The wide supply range accommodates multiple industrial and automotive-style voltage environments, while the low typical supply-current drain is advantageous in portable systems. An open-collector output also allows multiple comparators to share a pull-up node when wired logic is required. The primary design consideration is the open-collector output. Every output requires a suitable pull-up resistor and account for sink-current limits, rise time, bus capacitance, and the logic threshold of the receiving device. Input filtering may also be necessary when noisy analog signals are compared, while board placement should keep comparison inputs away from switching nodes and high-current return paths. This page combines the exact ordering designation with package, pin, application, and drop-in replacement guidance to support schematic review and PCB reuse. It also provides practical design notes for pull-up selection, input conditioning, and open-collector interfacing, helping engineers evaluate the LM2903 family beyond a basic datasheet parameter summary.

RFQ Kontak
LM2903DMR2 - Dual Precision Comparator, 36 V | onsemi
LM2903DMR2

LM2903DMR2 - Dual Precision Comparator, 36 V | onsemi

onsemi LM2903DMR2 is a dual independent precision voltage comparator designed for single-supply or split-supply operation, with a supply range extending to 36 V and an 8-pin SOIC package. The device compares two input voltages per channel and provides an open-collector output suitable for wired logic-level comparison and system monitoring. A voltage comparator is an analog integrated circuit that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy within analog signal-processing and interface ICs. Its two independent channels allow a single package to monitor two unrelated signals, while single- or split-supply operation makes it useful across industrial, automotive, and embedded power-control systems. The LM2903 series provides a common-mode input range that extends to ground under single-supply operation. This characteristic is important when a monitored signal can approach 0 V. The low-offset-voltage designation indicates that the comparators are intended to detect relatively small differential voltages, although the exact offset limits depend on the operating conditions specified in the onsemi datasheet. Each channel operates independently, allowing different threshold networks and signal pairs to share the package. The device supports supply voltages up to 36 V, which provides headroom for industrial and automotive environments. Its comparator outputs are designed for interfacing with conventional logic, although output topology, sink-current limits, and pull-up requirements must be confirmed from the manufacturer datasheet before final circuit design. Typical uses include power-supply sequencing, battery and charger threshold detection, overvoltage and undervoltage protection, window monitoring, sensor-level detection, and general signal conditioning. In a power system, the two channels can monitor independent rails or compare a feedback voltage against a reference. The open-collector-style interface also allows multiple devices to share a pull-up arrangement when the required bus architecture and current limits are appropriate. When laying out the circuit, keep comparator input nodes short and shield them from switching nodes and high-current paths. Confirm whether the selected output configuration requires an external pull-up resistor, and use that resistor to satisfy the downstream logic's rise-time requirements. Check supply-decoupling placement at the device pins and verify input and output limits for the complete temperature range. This product record combines the LM2903DMR2 electrical description, verified source links, same-package alternatives, application guidance, and design checks to support faster component selection and PCB-level engineering decisions.

RFQ Kontak
LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi
LM2903DMR2G

LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi

The onsemi LM2903DMR2G is a dual independent precision voltage comparator with 2 mV typical input offset voltage, 1.3 us typical response time, and a wide 2 V to 36 V supply range, housed in an 8-pin MSOP (Micro8) surface-mount package. A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators form the lowest tier of the amplifier IC hierarchy (comparator -> amplifier IC -> analog signal chain IC -> semiconductor) and differ from op-amps by their open-collector outputs and fast, unsaturated switching behavior. The LM2903 belongs to the industry-standard LM393 comparator family, which has been the default choice for level detection, threshold monitoring, and limit sensing across consumer, automotive, and industrial electronics for decades. Key features include low input offset voltage as low as 2.0 mV, input common-mode range extending down to ground (V-) level even under single-supply operation, low supply current of approximately 700 uA per package, and open-collector outputs compatible with TTL, MOS, and CMOS logic levels. The wide 2 V to 36 V single-supply range (or equivalent split-supply operation) allows direct connection to automotive 12 V and industrial 24 V rails without preconditioning. Architecturally, the device integrates two fully independent comparator channels that share only the supply pins, permitting simultaneous use without channel-to-channel interaction. The open-collector output stage requires an external pull-up resistor, which lets designers set the logic interface level independently of the supply - a 5 V pull-up on a 12 V-powered comparator interfaces directly with TTL logic. Typical applications include limit comparators and threshold detectors in power supplies, window comparators in battery chargers and over-voltage protection circuits, sensor conditioning for industrial automation, and level translation and oscillator timing circuits in consumer electronics. A key design consideration: because the output is open-collector, forgetting the pull-up resistor produces a permanently floating output; select the pull-up value for the required rise time and sink current, typically 3 k to 15 k. Also keep input differential voltage within the absolute maximum rating. This page consolidates verified electrical specifications, drop-in alternatives, application guidance, and practical design notes not found in a single manufacturer document.

RFQ Kontak
LM2903DR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)
LM2903DR

LM2903DR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)

The Texas Instruments LM2903DR is a dual differential analog comparator with two independent comparator channels, an operating supply range of 2 V to 36 V, a response time of 300 ns, and an 8-pin SOIC package. Each channel provides open-collector output behavior for level translation, relay driving, and wired-AND logic functions. The device is specified for operation from -40 °C to +125 °C according to the available manufacturer comparison data. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2903DR belongs to the comparator hierarchy within analog and mixed-signal semiconductors, providing a simple alternative to an operational amplifier configured as a comparator. Its two channels operate independently, allowing one package to implement two threshold decisions or to control complementary functions in a single circuit. The open-collector outputs are a defining electrical feature. Each output transistor can pull its output low, but it cannot actively drive the output high, so an external pull-up resistor is required. Multiple open-collector outputs can share one pull-up to create a wired-AND arrangement. This architecture also provides a useful form of output isolation while remaining compatible with standard 5 V and 3.3 V digital logic levels when the pull-up rail is selected appropriately. The 2 V to 36 V supply capability allows operation from low-voltage analog systems through conventional industrial control rails. Its 300 ns response time supports applications where decisions must be made faster than typical slow comparators but where nanosecond-level precision is unnecessary. The operating temperature range covers industrial environments, although production designs should still verify temperature-dependent input offset, output-current, and propagation-delay behavior using the selected manufacturer's complete datasheet. Typical uses include industrial sensor conditioning, battery monitoring, overvoltage detection, window or level comparators, relay and solenoid interfaces, and digital control systems that require open-collector outputs. The SOIC-8 package is also appropriate for through-hole-style PCB assembly and manual rework, although SOIC-8 is larger than modern comparator packages such as SOT-23 and MSOP-8 variants. When designing with the LM2903DR, always place the input and pull-up networks close to their associated pins, and account for input common-mode limits at the selected supply voltage. A pull-up resistor is not optional because the open-collector output cannot source current. Reviewing the voltage drop across the pull-up and the output transistor's current rating is essential when several outputs share the same node. This page consolidates verified distributor listings, manufacturer references, pin-compatible alternatives, package details, and practical circuit guidance. It also distinguishes directly interchangeable devices from higher-speed or higher-precision alternatives whose electrical behavior may require different design assumptions.

RFQ Kontak
LM2903DR2 - Dual 36 V Comparator | onsemi | SOIC-8
LM2903DR2

LM2903DR2 - Dual 36 V Comparator | onsemi | SOIC-8

onsemi LM2903DR2 is a dual differential voltage comparator designed for single-supply or split-supply operation between 2 V and 36 V. The device contains two independent comparison channels, supports a common-mode input range extending to ground in single-supply systems, and is packaged in an 8-pin SOIC. Its open-collector output architecture provides flexible interface options for wired logic, pull-up networks, relay drivers, and systems operating from multiple supply rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its primary role is threshold detection rather than linear amplification. Two independent channels allow one package to implement two unrelated sensing functions while sharing a common supply connection and ground reference. The LM2903 series combines low input-offset voltage, low input-bias current, and a wide supply-voltage range. Input offset voltage is specified as low as 2.0 mV, which helps define the input-voltage difference required to change output state. The 2 V to 36 V operating range supports legacy 5 V logic, industrial 12 V and 24 V rails, automotive-style 12 V systems, and higher-voltage threshold-detection circuits. The open-collector outputs permit an external pull-up voltage to be selected independently of the comparator supply. Each channel compares a non-inverting input with an inverting input. When the non-inverting voltage is higher, the corresponding open-collector output transistor turns on and pulls the output toward the pull-up rail; when the inverting voltage is higher, the transistor turns off and the output rises. The two channels are independent, although their supply and ground pins are shared. This arrangement supports sensor thresholding, window detection, and complementary decisions without requiring two separate packages. Typical uses include industrial control and factory automation, battery-powered monitoring, automotive battery and power-system detection, instrumentation, protection circuits, and embedded systems using 3.3 V or 5 V microcontroller interfaces. For digital interfaces, the open-collector output can use a pull-up to the logic rail used by a comparator input or microcontroller. The SOIC-8 package also supports conventional surface-mount assembly and hand-soldering workflows. Designers should verify the allowable input and output voltage relationships, including the differential input range, and use a pull-up resistor that supplies adequate output current without exceeding the output transistor's limits. Care is also needed when a channel drives a cable, relay, or large capacitance because slower edges and parasitic coupling can affect system behavior. The input network should include suitable filtering when the sensed signal contains switching noise. This product overview combines the exact LM2903DR2 ordering identity with practical guidance on comparator operation, pin usage, output interfacing, and verified drop-in options. It is intended to support component selection, PCB replacement, and design reviews involving dual open-collector comparators in SOIC-8 packages.

RFQ Kontak
LM2903DR2G - Dual 36V Open-Collector Comparator | onsemi
LM2903DR2G

LM2903DR2G - Dual 36V Open-Collector Comparator | onsemi

onsemi LM2903DR2G is a dual differential voltage comparator with two independent comparator channels, 2 V to 36 V supply operation, open-collector outputs, 1.5 µs propagation delay, and an 8-pin SOIC package. The device also supports split-supply operation with stated rails from ±1 V to ±18 V and an input offset voltage as low as 2.0 mV. A dual comparator is a semiconductor that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the broader voltage-comparator hierarchy within analog integrated circuits and power-management signal conditioning. Its two independent channels allow simultaneous or separate threshold, window, sensing, and level-detection functions without requiring two separate comparator packages. Key features include two open-collector channels, a 1.5 µs response time, and low-offset operation with input offset voltage specifications as low as 2.0 mV. The 2 V to 36 V total supply range supports industrial, automotive-style, and embedded applications where the comparator may operate from a single supply or from positive and negative rails. Open-collector outputs permit external pull-up selection and can interface with TTL, MOS, or CMOS-compatible systems when the pull-up voltage and current are appropriate. The comparator architecture is appropriate when a design needs a digital decision rather than a linear analog output. Each channel can compare a sensed voltage against a reference threshold, while the open-collector structure allows wired logic, alarm signaling, or direct control of a pull-up-equipped input. Operation from single or split supplies expands its usefulness in power systems that use both positive and negative reference rails. Typical applications include automotive battery and power-rail monitoring, industrial control thresholds, motor and actuator interfaces, sensor conditioning, overvoltage and undervoltage detection, and embedded system supervision. The 8-SOIC package provides a conventional surface-mount footprint, while the dual-channel configuration helps reduce component count in dual-threshold or multi-channel sensing designs. Designers should verify input common-mode limits, output pull-up values, differential input limits, and the exact electrical grade associated with the selected ordering code. Keep output pull-up paths short, provide adequate return-current routing, and account for the open-collector output’s tendency to sink current rather than source it. The Request a Quote form on this page supports current commercial sourcing questions. This page organizes the LM2903DR2G electrical characteristics, package information, drop-in candidates, comparison parameters, and practical circuit-placement guidance. It also identifies which ordering variants are technically suitable for footprint reuse and where direct replacement requires additional engineering review.

RFQ Kontak
LM2903DRE4 - Dual 2-36V Comparator | Texas Instruments
LM2903DRE4

LM2903DRE4 - Dual 2-36V Comparator | Texas Instruments

Texas Instruments LM2903DRE4 is a dual differential voltage comparator with open-collector outputs, rail-to-rail input capability, a 2 V to 36 V supply range, and an 8-pin SOIC package. Each channel can operate independently, making the device suitable for threshold detection, level translation, window monitoring, and industrial control tasks. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when one input crosses the other. A dual comparator contains two electrically independent comparator channels in one package. The LM2903 belongs to the voltage comparator hierarchy, where it can be described more specifically as a differential comparator with open-collector outputs. It operates from a single supply or from split supplies, making it suitable for industrial power systems with widely separated ground references. The principal advantages of the LM2903DRE4 are its broad 2 V to 36 V operating supply range, rail-to-rail input characteristic, low typical supply-current drain of 0.4 mA per comparator, and 300 ns response time. The two open-collector outputs allow the output state to be pulled up to an external voltage and provide wired-AND behavior when several comparators share a pull-up resistor. This output arrangement is useful when interfacing with open-drain logic, relay drivers, or subsequent CMOS and TTL stages. Each comparator contains independent input and output circuitry. Differential input voltage is evaluated between the inverting and noninverting inputs, and the output transistor is turned off or on according to that relationship and the polarity of the open-collector stage. Because the outputs are open collector, the output voltage depends on the pull-up network rather than the comparator alone. Designers must account for leakage current, pull-up resistance, logic thresholds, and propagation delay when translating a high-impedance output state into a valid digital level. Typical uses include industrial sensor thresholds, battery and power-supply monitoring, overvoltage detection, motor-control signaling, and general-purpose logic interfacing. A split-supply arrangement can compare bipolar signals around ground, while a single-supply arrangement supports systems whose input common-mode range reaches the lower supply rail. The 8-pin SOIC package also supports conventional surface-mount assembly and easy routing between two comparator channels. A key design consideration is that open-collector outputs require an external pull-up resistor. Select that resistor so that its maximum current and the output leakage current still produce a valid high level, while keeping rise time consistent with the required system response. The 300 ns propagation delay is important for high-speed threshold decisions, but slower pull-up networks can add additional delay after the comparator changes state. This page combines manufacturer and distributor information with package guidance, application analysis, cross-brand substitution notes, and engineering-focused design advice to help evaluate the LM2903DRE4 beyond a basic catalog listing.

RFQ Kontak
LM2903DRG3 - Dual Open-Collector Comparator | Texas Instruments
LM2903DRG3

LM2903DRG3 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903DRG3 is a dual differential comparator with open-collector outputs, operating from 2 V to 36 V on a single supply or ±1 V to ±18 V on dual supplies, in an 8-pin SOIC package. Each of the two independent comparator channels draws 200 µA of supply current and offers a 1 µs response time, making the LM2903DRG3 a standard general-purpose comparator for industrial, automotive and instrumentation signal chains. A comparator is a differential amplifier whose output is driven to a logic state when one input exceeds the other by more than the input offset voltage. It belongs to the amplifier IC family, sits under the operational amplifier hierarchy, and ultimately falls inside the linear and signal-conditioning IC category. Unlike an op-amp, a comparator has no linear output region and is not intended for open-loop gain; its open-collector output is designed to pull a rail low and to be pulled up externally, which allows it to sink more current than a CMOS push-pull output can. Key features include a maximum rated supply of up to 38 V, an ESD rating of 2 kV HBM, a low input offset voltage of 0.37 mV and a low input bias current of 3.5 nA, all of which improve threshold accuracy and reduce source loading on the sensed signal. The differential input voltage range is equal to the maximum rated supply voltage at ±38 V, and the common-mode input voltage range includes ground, allowing the device to monitor bipolar signals referenced to 0 V. Outputs are compatible with TTL, MOS and CMOS logic families. Electrically the device is a bipolar dual differential comparator with an open-collector output stage. The open-collector architecture means the output can be pulled to any supply level the system uses, and a pull-up resistor sets the high level. This is essential in relay-drive, lamp-drive and level-shifting designs where the load requires more current than the IC itself can source. Typical applications include industrial sensor threshold detection, battery and rail window comparison, overvoltage and undervoltage protection in power supplies, temperature monitoring with thermistors or RTDs, and current-sense comparison in motor drive and inverter control stages. When designing with the LM2903DRG3, always place the pull-up resistor close to the output pin and check that the total sink current stays within the output rating, because the open-collector transistor, not the internal drive, sets the load capability. This page consolidates parametric data, drop-in alternatives, comparison tables and practical design notes so engineers can evaluate the LM2903DRG3 against equivalent dual comparators without rebuilding the analysis from scratch.

RFQ Kontak
LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments
LM2903DRG4

LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DRG4 is a dual differential voltage comparator with an open-collector output, supplied in an 8-pin SOIC package. It operates from a single supply over a 2 V to 30 V range, or from dual supplies when the total supply difference remains within 2 V to 36 V. The device contains two independent comparators, making it suitable for threshold detection, window comparison, and industrial control functions. The LM2903 is a general-purpose comparator within the broader category of analog comparator ICs. A comparator evaluates two input voltages and produces a logic-level result indicating which input is higher. In an open-collector implementation, the output stage can sink current while remaining in a high-impedance state when the device is inactive. This architecture allows external pull-up resistors to set the output voltage and interface with TTL, MOS, or CMOS logic. Key characteristics include a 2 V to 30 V supply range for the non-V device, a 30 V maximum supply rating, approximately 1.3 microsecond propagation delay, and typical supply-current drain of approximately 0.4 mA per comparator. The input common-mode range includes ground, and the differential input voltage range is equal to the maximum-rated supply voltage at ±38 V for the versions described by the manufacturer. The open-collector outputs require pull-up resistors when connected to digital logic. The outputs are intended to sink rather than source output current, so the pull-up resistor value determines the rise time, power consumption, and compatibility with the receiving logic. The wide supply range and low-power operation make the LM2903 suitable for process control, power supervision, sensor conditioning, and general-purpose threshold detection. When designing around the LM2903, verify the supply limits, common-mode input range, differential input limits, output pull-up network, and the switching behavior required by the downstream circuit. The device is a dual comparator, so each channel is independent, but both channels share the same supply pins and package footprint. The SOIC-8 format supports conventional surface-mount assembly and provides a practical upgrade path from through-hole comparator designs when the pin configuration is verified. This page brings together the manufacturer product information, verified distributor references, package details, drop-in comparison options, and application guidance for engineers evaluating the LM2903DRG4 in new analog-control and embedded-system designs.

RFQ Kontak
LM2903EPWRQ1 - Automotive Dual Comparator | Texas Instruments
LM2903EPWRQ1

LM2903EPWRQ1 - Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903EPWRQ1 is an automotive dual differential comparator with two independent comparator channels, open-collector outputs, and operation across a 2 V to 30 V supply range. It is qualified to AEC-Q100 Grade 0 and Grade 1 and is packaged in an 8-pin TSSOP (PW) package for automotive and industrial systems. The device is intended for high-voltage signal-chain applications where a robust differential input comparator is needed to monitor two voltages and report their relationship. A comparator is an analog integrated circuit that compares an input voltage with a reference or threshold voltage and switches its output when the differential polarity changes. LM2903EPWRQ1 belongs to the differential comparator family within the broader voltage-comparison, signal-conditioning, and power-management IC hierarchy. Its differential inputs allow one signal to be evaluated against another rather than against a fixed internal reference, making it useful for threshold detection, overvoltage and undervoltage monitoring, sensor conditioning, and control systems. The dual-channel architecture provides two comparators in one package while keeping each channel independent. The open-collector output structure allows the output transistor to remain off when the output is high-impedance, which supports wired logic, pulled-up buses, and systems requiring an external pull-up resistor. The automotive qualification provides an important distinction from standard industrial comparator variants because the LM2903-Q1 family is characterized for Grade 0 and Grade 1 operating environments. Typical applications include automotive battery monitoring, 12 V and 24 V power-system supervision, sensor threshold detection, window and system monitoring, industrial control panels, and automotive actuator or interface circuits. The 30 V maximum supply rating provides useful headroom for systems with battery transients and elevated industrial rails. When designing a comparator circuit, verify the input common-mode range, output pull-up requirements, propagation delay, and the electrical limits for the intended automotive operating environment. The LM2903EPWRQ1 is supplied in an 8-pin TSSOP (PW) package, allowing compact PCB placement while supporting the pin arrangement of the LM2903-Q1 family. For new designs, confirm the selected ordering code against the manufacturer datasheet and validate the external pull-up resistor and input filtering for the specific signal environment.

RFQ Kontak
LM2903FVJ-E2 - Dual Ground-Sense Comparator | ROHM Semiconductor
LM2903FVJ-E2

LM2903FVJ-E2 - Dual Ground-Sense Comparator | ROHM Semiconductor

ROHM Semiconductor LM2903FVJ-E2 is a dual-channel, general-purpose ground-sense comparator with open-collector outputs and a 3 V to 32 V operating supply range. The device is packaged in an 8-pin TSSOP-B8J package and is supplied in tape-and-reel packing. ROHM lists the LM2903FVJ as Not Recommended for New Designs, so the part is best evaluated for existing designs, maintenance, and previously qualified industrial equipment rather than new product creation. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. The dual architecture provides two comparison channels in one package, reducing component count when a board needs independent threshold decisions. The LM2903FVJ-E2 is intended for ground-sense applications, where a comparator evaluates a signal relative to a ground-referenced threshold and drives an open-collector output. Open-collector outputs allow wired-AND behavior when several outputs share a pull-up resistor, which is useful in alarm, interlock, and system-fault signaling circuits. The key operating characteristics are the 3 V to 32 V supply range, two comparator channels, ground-sense input arrangement, and open-collector output architecture. The broad supply range allows the device to operate from conventional 5 V and 12 V industrial rails as well as higher-voltage systems, subject to the limits in the manufacturer datasheet. Its open-collector output stage requires an external pull-up resistor when a logic-high output is required. The output should not be assumed to drive a load directly; the pull-up resistor, downstream logic input, and fault-state behavior must be checked together. Typical uses include overvoltage and undervoltage indication, ground-fault detection, battery or power-supply monitoring, industrial control interlock logic, threshold-based signal conditioning, and general embedded control. The comparator can operate directly from higher-voltage rails, but the input pins, output pull-up network, grounding, and protection network must remain within their specified limits. External filtering or clamping may be required when the monitored signal contains transients or exceeds the input common-mode range. Designers should review the ROHM datasheet for the complete electrical limits, input common-mode range, output sink-current capability, response-time behavior, and package details before release to production. Because the manufacturer marks the LM2903FVJ as Not Recommended for New Designs, a responsible product decision should compare current ROHM alternatives rather than treating this part as the preferred choice for a fresh design. Existing production equipment may still benefit from a qualified replacement strategy when availability, lifecycle status, and electrical compatibility are reviewed. This product summary consolidates the manufacturer product identity, package information, lifecycle status, operating-range information, practical application guidance, and sourcing questions into one engineering reference. It is intended to support initial part identification, circuit review, and replacement planning without replacing the complete manufacturer datasheet.

RFQ Kontak