Texas Instruments

LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments

MPN: LM2903BIDGKR ✓ Nakahanda
38 V Vdss 3.5 nA maximum Id 8-pin VSSOP Package
MOQ: 1 |

LM2903BIDGKR Ulas

Texas Instruments LM2903BIDGKR is a dual differential comparator with two independent channels, a maximum rated supply voltage of 38 V, open-collector outputs, and an 8-VSSOP package. It operates from a 2 V to 36 V supply, supports input common-mode and differential voltages up to ±38 V, and is specified as a rail-to-rail input device with 0.37 mV input offset voltage.

A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a threshold. The LM2903B belongs to the comparator hierarchy within analog and power-management semiconductors. Unlike an operational amplifier, each channel does not require feedback compensation for linear amplification, and its open-collector output must connect to an external pull-up resistor when driving a logic input.

Key B-version improvements include lower offset voltage, lower input bias current, lower supply current, faster response, and stronger input protection than the original LM2903. The device features 0.37 mV input offset voltage, 3.5 nA input bias current, 200 μA supply current per comparator, 1 μs response time, and a 2 kV human-body-model ESD rating. Its outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer documentation.

Each internal comparator is electrically independent, but both channels share the supply pins and ground connection. Separate input and output pins allow one channel to perform threshold detection while the other performs window monitoring, current sensing, or another independent comparison. The open-collector architecture provides wired-AND behavior when multiple outputs share a pull-up node, although rise time then depends on the resistor, capacitance, and leakage current.

Typical uses include industrial sensor thresholding, battery and power-supply monitoring, overvoltage detection, signal conditioning, and embedded control systems. The wide 38 V maximum rating is useful in industrial environments where input transients can exceed nominal logic levels, but system designers must still validate signal levels and protection requirements for every operating condition.

For layout, route the comparator inputs away from switching nodes and place input-referred components close to their associated pins. Select the external output pull-up to balance sink-current capability against rise time. Verify input common-mode range, output pull-up voltage, package thermal conditions, and system shutdown behavior against the manufacturer datasheet before production release.

This page combines the LM2903B electrical characteristics, package and pin information, application guidance, design checks, and verified drop-in alternatives. It also highlights practical considerations for pull-up selection, input protection, noise, and industrial qualification that engineers can apply directly during schematic review and PCB design.

Mga alternatibo na pwedeng ilagay na LM2903BIDGKR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok LM2903BIDGKR (parehas na form factor at footprint) — pagkakaiba sa Comparator Type, Number of Channels, Output Type, Package.

Texas Instruments
Comparator Type: Dual differential voltage comparator
Number of Channels: 2
Output Type: Open-collector
Ikabit sa LM2903BIDGKR →

LM2903AVQPWR

✅ Drop-In
Texas Instruments
📦 8-pin VSSOP
Dual differential voltage comparator · 2 · Single supply or dual supplies · 30 V for V-suffix devices; 32 V for non-V devices · 0.4 mA typical per comparator · Open-collector · Differential input

Magkontak para sa presyo

Tingnan ang Datasheet →

LM2903BIDGKR Mga Pinakamataas na Rating at Electrical Characteristics

Comparator Type Dual differential comparator
Number of Channels 2 independent channels
Maximum Supply Voltage 38 V
Supply Voltage na Operasyon 2 V to 36 V
Input Common-Mode Voltage Range Rail-to-rail
Differential Input Voltage Range ±38 V
Input Offset Voltage 0.37 mV maximum
Input Bias Current 3.5 nA maximum
Kuru-kuryente ng Pagbibigay 200 μA per comparator
Response Time 1 μs
ESD Rating 2 kV HBM
Type ng Output Open collector
Output Logic Compatibility TTL, MOS, and CMOS
Qualification Class Industrial grade
Packhaging 8-pin VSSOP
Uri ng Pagpapasok Surface mount

Pin Configuration ng LM2903BIDGKR

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Pin 1 OUT1 — Comparator 1 open-collector output
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 noninverting input
Pin 4 GND — Ground connection
Pin 5 IN2+ — Comparator 2 noninverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 open-collector output
Pin 8 VCC — Positive supply connection

Tipikal na mga Gamit

LM2903BIDGKR ay nararapat para sa 6 aplikasyons: Industrial Sensor Threshold Detection, Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Window and Limit Monitoring, Motor and Solenoid Current Sensing, Embedded Control Signal Conditioning.

🏭

Industrial Sensor Threshold Detection

The LM2903BIDGKR fits industrial sensor threshold detection because its two channels can monitor two independent signals while providing 0.37 mV maximum input offset voltage and 3.5 nA maximum input bias current. Connect one channel to a sensor signal and a precision reference to determine an upper or lower threshold. The dual architecture can monitor a second sensor or a validity signal without adding another comparator package. Because the comparator supports a 38 V maximum rated supply, it can interface with suitably protected industrial sensor lines. Add input clamps when wiring leaves the board, because the 38 V differential rating does not remove the need to control every input transient.

⚡

Power-Supply Overvoltage Detection

The LM2903BIDGKR is appropriate for power-supply overvoltage detection because it combines two independent channels with a 38 V maximum supply rating and 1 μs response time. One channel can compare a divided feedback voltage with a reference, while the other can monitor an auxiliary rail or UVLO condition. The open-collector output can pull a system-fault line low and remain compatible with CMOS or TTL logic when paired with the correct pull-up supply. Validate the divider tolerances, input filtering, and maximum monitored voltage so that startup overshoot cannot exceed the comparator's absolute-maximum limits.

🔋

Battery Voltage Monitoring

The LM2903BIDGKR can support battery voltage monitoring in industrial or high-voltage systems where a resistive divider brings the cell or pack voltage into the comparator input range. Its low 3.5 nA maximum input bias current reduces divider-loading error, while the 0.37 mV maximum offset helps preserve threshold accuracy after gain and reference errors are included. The two channels can monitor charge and discharge limits separately. Keep the divider current high enough to dominate input leakage, and protect the input pins from battery disconnection transients and high-energy fault events.

📺

Window and Limit Monitoring

The two independent channels of the LM2903BIDGKR are well suited to window monitoring, where one output indicates a below-limit condition and the other indicates an above-limit condition. A divided sensor voltage can be compared against two reference levels, producing separate fault indications for excessive and insufficient system conditions. The 1 μs response time supports rapid threshold events, while the 200 μA supply current per comparator limits continuous overhead in battery-operated equipment. External pull-ups should be selected for the required fault-line rise time, and unused comparator inputs must be tied to a defined potential.

🏭

Motor and Solenoid Current Sensing

The LM2903BIDGKR can detect a current-shunt voltage and provide a digital fault signal for motor or solenoid control. Place the shunt near ground and compare the amplified or divided shunt voltage with a threshold reference, taking advantage of the comparator's 3.5 nA maximum input bias current to avoid significantly loading the sensing node. The second channel can monitor an overtemperature or driver-fault signal. Because switching nodes can produce fast transients, use a protection network and maintain a low-impedance return path from the shunt to the comparator ground.

🖥️

Embedded Control Signal Conditioning

The LM2903BIDGKR converts an analog control or status signal into a logic decision for a microcontroller or programmable controller. Its dual-channel arrangement reduces component count when the controller needs both a rising threshold and a falling threshold, while the 1 μs response time provides rapid event capture. The 2 V to 36 V operating supply range supports industrial rails, and open-collector outputs permit wired fault signaling with an external pull-up. Confirm logic thresholds, input offsets, pull-up voltage, and grounding topology against the controller's electrical requirements before release.

What are the key specifications of LM2903BIDGKR that engineers should know?
The LM2903BIDGKR is a dual industrial-grade differential comparator with a 2 V to 36 V operating supply, a 38 V maximum rating, and an 8-VSSOP package. According to the Texas Instruments datasheet, it provides 0.37 mV maximum input offset voltage, 3.5 nA maximum input bias current, 200 μA supply current per comparator, 1 μs response time, and 2 kV HBM ESD protection. The two channels are independent, while each output uses an open-collector structure requiring an external pull-up resistor for normal logic-high operation.
Where can I download the LM2903BIDGKR datasheet PDF?
The official LM2903B datasheet is available from Texas Instruments at https://www.ti.com/lit/gpn/LM2903B. It defines the LM2903BIDGKR ordering option, electrical characteristics, VSSOP pin assignments, application information, and recommended operating conditions. The manufacturer product page at https://www.ti.com/product/LM2903B provides ordering and parameter information. For PCB implementation, use the package drawing and pin table in the official datasheet rather than relying only on a distributor catalog diagram.
What is the LM2903BIDGKR pinout?
The LM2903BIDGKR uses an 8-pin VSSOP with two independent comparator channels. According to the manufacturer pin-description table, pin 1 is OUT1, pin 2 is IN1−, pin 3 is IN1+, pin 4 is GND, pin 5 is IN2+, pin 6 is IN2−, pin 7 is OUT2, and pin 8 is VCC. Verify these assignments against the official datasheet before routing a replacement board. The exposed package construction and absence of a separate exposed thermal pad should also be checked against the selected land pattern.
How does the LM2903BIDGKR open-collector output work?
The LM2903BIDGKR output actively pulls low but does not source a logic-high current, so each output requires an external pull-up resistor to the appropriate supply rail. According to the manufacturer documentation, the open-collector output is compatible with TTL, MOS, and CMOS logic. The pull-up value determines output rise time, while the maximum output sink current determines the lowest usable resistance. Do not leave an output without a pull-up if the connected circuit interprets an undriven state as a valid logic level.
What is the input common-mode voltage range of LM2903BIDGKR?
The LM2903BIDGKR is described as a rail-to-rail input comparator, allowing its input voltages to operate across the supply rails under the specified conditions. The manufacturer also states that the differential input voltage range equals the maximum-rated supply voltage of ±38 V. Rail-to-rail input behavior does not eliminate all input-overvoltage risk, so clamp signals that can exceed the supply rails during startup, shutdown, or fault conditions. The absolute-maximum table in the datasheet remains the governing design reference.
What can replace the LM2903BIDGKR as a drop-in part?
The LM2903AVQPWR is a documented same-family option to evaluate for a drop-in replacement because it belongs to the LM2903A/LM2903B family and uses the comparable small-outline package arrangement. Texas Instruments states that the B version can replace A- and V-grade LM2903 devices, while automotive qualification differences must still be checked. Before substitution, confirm pin orientation, package dimensions, common-mode limits, output pull-up requirements, temperature range, and qualification status for the target equipment.
Is the LM2903AVQPWR the same as the LM2903BIDGKR?
The LM2903AVQPWR is not an identical ordering code, but it is a closely related member of the LM2903 comparator family. The key selection question is whether its exact grade and package are acceptable for the application: the A-version designation may impose automotive-oriented requirements, while the B-version designation identifies a different performance-generation variant. Use the manufacturer comparison and package drawings to verify compatibility rather than assuming that every LM2903 ordering code is interchangeable in every production program.
When should I choose LM2903BIDGKR instead of another LM2903 grade?
Choose the LM2903BIDGKR when an industrial-grade, 38 V-rated dual comparator with improved offset, bias current, response time, and ESD performance is required. Select an automotive-qualified ordering option only when the finished system requires that qualification, and select another grade when its temperature, quality, or qualification target better matches the product. The B-version features make the part appropriate for cost-sensitive industrial designs that benefit from the improved electrical characteristics without requiring an automotive qualification.
Is LM2903BIDGKR suitable for industrial sensor thresholding?
Yes, the LM2903BIDGKR is suitable for industrial sensor thresholding because it is an industrial-grade dual comparator with a 38 V maximum supply rating, 0.37 mV maximum offset voltage, and 3.5 nA maximum input bias current. Place it in the signal path after conditioning the sensor output so that the comparator input remains within its absolute-maximum limits. Add suitable input filtering or clamping when long cables, inductive loads, or switching transients can create fast overvoltage events.
How should I design the pull-up resistor for LM2903BIDGKR?
Choose the pull-up resistor so that its maximum sink current at the output-low state remains within the comparator's rated sink-current capability, while its minimum resistance also provides adequate output rise time. A larger resistor reduces sink demand but increases rise time and susceptibility to leakage or coupling; a smaller resistor improves rise time but increases current. Confirm the output-low voltage, sink-current limit, pull-up voltage, bus capacitance, and required logic timing in the manufacturer electrical-characteristics table.
Does the LM2903BIDGKR need an output pull-up resistor?
Yes, the LM2903BIDGKR normally requires an external pull-up resistor on each open-collector output. The output transistor pulls the node toward ground when the comparator changes state, but it cannot actively drive the node high. The pull-up can connect to a suitable logic supply rather than the comparator supply if the output must never exceed the connected logic device's limits. In a wired-AND arrangement, multiple open-collector outputs may share one pull-up node.
What is the difference between LM2903 and LM393?
The LM2903 and LM393 are both dual differential comparators with open-collector outputs, but their ordering options, temperature coverage, qualification, and exact electrical limits can differ. The LM2903B is the B-generation family specified here, with improved offset voltage, input bias current, supply current, response time, maximum voltage capability, and ESD performance. Selection should therefore be based on the complete ordering code and datasheet rather than the comparator function alone. The manufacturer comparison material documents that B versions can replace several older LM2903 and LM393 grades.
Where can I buy LM2903BIDGKR and check its price?
Use the Request a Quote form on this page to request LM2903BIDGKR pricing, stock confirmation, and current lead time for the exact Texas Instruments ordering code. The quote form helps prevent mismatches involving package, reel configuration, temperature grade, or quantity. This page does not present a static price or fixed stock claim because commercial availability can change. Include your target quantity, acceptable delivery date, and production or prototype stage when submitting the request.
What is the lead time for LM2903BIDGKR?
The current lead time for LM2903BIDGKR depends on quantity, procurement status, and the manufacturer's manufacturing conditions. Use the Request a Quote form on this page for a current allocation and delivery estimate. When requesting the quote, specify reel quantity, target shipment date, and whether the shipment is for prototype, qualification, or production use. The exact MPN and package code should appear on the quotation so procurement does not substitute a mechanically similar ordering option.
Is LM2903BIDGKR in stock?
Use the Request a Quote form on this page for the current LM2903BIDGKR availability and an allocation for your required quantity. Stock status can change quickly and may differ between single-unit evaluation quantities and production reels. State the required quantity and delivery schedule in the request. The manufacturer lists the LM2903B family as an active product family, but that product-family status does not by itself confirm current inventory for every package and reel quantity.
What is the best cross-brand equivalent for LM2903BIDGKR?
No cross-brand equivalent can be recommended as a confirmed drop-in replacement from the available cross-reference information. A valid cross-brand replacement must match the 8-pin VSSOP footprint and pinout, 38 V maximum rating, input common-mode range, open-collector output behavior, timing, temperature grade, and qualification requirements. Use the Request a Quote form on this page to discuss sourcing support for the original part. Any second-source candidate should be checked against its manufacturer datasheet before schematic or PCB release.

Impormasyon ng Talumpati sa Engineering for LM2903BIDGKR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the LM2903BIDGKR for industrial signal-conditioning and threshold-detection designs that require two independent channels, a 38 V maximum supply rating, 0.37 mV maximum offset voltage, and an 8-VSSOP footprint. Its open-collector outputs are useful for wired fault signals, provided each output receives a correctly selected pull-up. Consider the LM2903AVQPWR when a closely related same-family grade is acceptable, but verify its package dimensions, electrical limits, temperature coverage, and automotive qualification implications before substitution. A separate single-channel comparator may be simpler when only one threshold is needed, while a dual op-amp with inputs biased near the supply rails may offer a different output drive architecture. The final choice should be based on input topology, output logic voltage, timing, protection, qualification, and package fit rather than comparator function alone.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto LM2903AVQPWR
Brand Texas Instruments Texas Instruments
Package 8-pin VSSOP 8-pin VSSOP
Comparator Configuration Dual differential Dual differential
Output Type Open collector Open collector
Grade Industrial grade Automotive-oriented A-version grade

Pangunahing mga Pagkakaiba

  • Improved B-version input accuracy (kumpara saLM2903AVQPWR)
  • Low input loading for high-impedance sensing (kumpara saLM2903AVQPWR)
  • Compact dual-channel implementation (kumpara saLM2903AVQPWR)

Talaan ng Disenyo

Do not treat the 38 V maximum supply rating as permission to apply 38 V continuously to every input. Check input common-mode limits, differential input limits, and absolute-maximum conditions separately, especially during power-up and shutdown. The open-collector outputs also require an external pull-up; omitting it can leave the connected logic input floating. Confirm that every unused comparator input is connected to a defined voltage rather than allowed to float.

Place input-divider resistors, reference components, and protection devices close to the comparator pins to minimize parasitic capacitance and susceptibility to injected noise. Keep the comparator ground connection short and return it to the quiet ground reference used by the sensed signal. For shunt-current sensing, use a dedicated low-impedance ground path from the shunt to the comparator ground instead of sharing a long return with switching loads.

Select the open-collector pull-up using three constraints: the output-low sink-current rating, the required logic rise time, and the pull-up voltage allowed by the connected device. A smaller pull-up improves rise time but increases sink current; a larger pull-up reduces current but slows the edge. Include bus capacitance and leakage when timing the rising transition, and use the datasheet's output-low voltage curve to verify the margin at the intended sink current.

The 200 μA-per-comparator supply current is low, but total system demand also includes input bias current, pull-up current, reference circuits, and external logic loads. Estimate the comparator's average dissipation as the supply voltage multiplied by the total device current, then include resistor-network loading separately. Provide adequate local bypassing at VCC and keep the supply return path short to limit transient coupling into the sensitive input nodes.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Qualified
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The LM2903BIDGKR is identified as industrial grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation. The LM2903AVQPWR alternative carries automotive-oriented grade considerations.

Data napatotohanan sa: 2026-11-09 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

lm2903bidgkr datasheet LM2903BIDGKR pinout LM2903BIDGKR datasheet pdf LM2903BIDGKR equivalent LM2903BIDGKR replacement LM2903BIDGKR cross reference LM2903BIDGKR vs LM2903AVQPWR LM2903BIDGKR VSSOP footprint LM2903BIDGKR open collector output LM2903BIDGKR 38V comparator Texas Instruments LM2903BIDGKR LM2903BIDGKR price LM2903BIDGKR stock

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments LM2903BIDGKR LM2903B LM2903AVQPWR dual differential comparator comparator analog integrated circuit semiconductor open-collector output input offset voltage input bias current rail-to-rail input common-mode voltage differential input voltage TTL MOS CMOS ESD protection 8-pin VSSOP VSSOP package family surface-mount package industrial electronics power-supply monitoring sensor thresholding wired-AND logic
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ