Mga Produkto (46,000+)

LM324QDRQ1 - Automotive Quad Op Amp, 1MHz, RRO | TI
LM324QDRQ1

LM324QDRQ1 - Automotive Quad Op Amp, 1MHz, RRO | TI

The Texas Instruments LM324QDRQ1 is an automotive-qualified quad operational amplifier delivering a 1 MHz gain-bandwidth product and rail-to-rail output (RRO) swing in a 14-pin SOIC (D) surface-mount package. It operates from a single supply of 2.7 V to 5.5 V (or dual supplies of +/-1.35 V to +/-2.75 V), making it well suited to battery-powered and low-voltage automotive systems. An operational amplifier (op amp) is a high-gain differential-input voltage amplifier and one of the most fundamental building blocks in analog electronics, used for signal conditioning, active filtering, and mathematical operations. Within the analog IC hierarchy, general-purpose op amps belong to linear integrated circuits, alongside comparators, voltage references, and voltage regulators. Quad op amps like this device integrate four matched amplifiers on a single die, saving board space and improving channel matching in multi-channel signal chains. Key features include rail-to-rail output swing that maximizes dynamic range at low supply voltages, a maximum input offset voltage of 4 mV, and a typical common-mode rejection ratio (CMRR) of 65 dB. Each amplifier draws approximately 100 uA of quiescent current, enabling low-power designs, while internal frequency compensation guarantees unity-gain stability without external components. Technically, the device uses bipolar process technology for good linearity, includes short-circuit protection and output current limiting for robustness, and specifies output current capability of around 160 mA per channel under rated conditions per distributor data. The AEC-Q100 qualification and wide temperature rating make it suitable for harsh automotive environments with 3.3 V and 5 V microcontroller-based systems. Typical applications include automotive sensor signal conditioning (temperature, pressure, and position sensors), battery management system monitoring front-ends, and motor control circuits paired with MCUs such as TI C2000 and MSPM0 families. Design tip: decouple the supply pin with a 0.1 uF ceramic capacitor placed close to the device, and respect the input common-mode range, which extends from ground to VCC - 1.5 V, to avoid phase-reversal and nonlinear behavior near the upper rail.

RFQ Kontak
LM324QT - Quad Low Power Op Amp, 1.3MHz | STMicroelectronics
LM324QT

LM324QT - Quad Low Power Op Amp, 1.3MHz | STMicroelectronics

The LM324QT from STMicroelectronics is a quad general-purpose operational amplifier in a compact 16-pin QFN (3x3 mm) package. It operates from a single power supply over a wide voltage range, making it ideal for space-constrained, battery-powered applications. The device features four independent, high-gain, frequency-compensated amplifiers with a gain bandwidth product of 1.3 MHz and a slew rate of 0.4 V/us. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is the fundamental building block of analog signal conditioning, used in filters, comparators, integrators, and many other circuits. The LM324QT belongs to the LM324 family, a classic industry-standard quad op amp known for its low power consumption and wide supply range, which includes the ability to operate from a single supply down to 3V. Key features include a wide gain bandwidth of 1.3 MHz, a large voltage gain of 100 dB, and a very low supply current per amplifier of 375 uA. The input common-mode voltage range includes ground, allowing single-supply operation with ground-referenced inputs. The device also features low input bias current and internal frequency compensation, simplifying design and reducing external component count. The LM324QT uses a bipolar process technology, providing robust performance over a wide temperature range. The QFN package offers excellent thermal performance and a small footprint, making it suitable for compact designs. The device is designed for low-power operation, making it ideal for battery-powered equipment where power efficiency is critical. Typical applications include sensor signal conditioning, active filters, DC gain blocks, and transducer amplifiers. The wide supply voltage range and low power consumption make it suitable for automotive, industrial, and consumer electronics. The QFN package is particularly well-suited for portable devices where board space is at a premium. When designing with the LM324QT, ensure proper decoupling of the power supply pins with a 0.1 uF ceramic capacitor placed close to the device. The input common-mode range includes ground, but for best performance, keep inputs within the specified range. The output can swing close to the rails, but avoid driving loads that require rail-to-rail output swing without proper design considerations.

RFQ Kontak
LM324SNG - Quad Op-Amp 14-PDIP | onsemi | Single Supply
LM324SNG

LM324SNG - Quad Op-Amp 14-PDIP | onsemi | Single Supply

The onsemi LM324SNG is a low-cost quad operational amplifier with four independent, high-gain, internally frequency-compensated op amps in a 14-pin PDIP (dip-14) through-hole package. The LM324S is onsemi's version of the industry-standard LM324 family: single-supply quad operational amplifiers with true differential inputs, specified for operation from a single 3 V to 32 V supply or dual supplies up to ±16 V. A quad operational amplifier is an analog IC that integrates four independent op amp circuits on one die, sharing the same supply pins while keeping inputs and outputs separate. In the amplifier hierarchy it sits as an amplifier IC > operational amplifier > general-purpose amplifier, forming the analog signal-conditioning backbone of power management, sensing, and control systems. Key advantages of the LM324S family over standard op amps in single-supply applications include a common-mode input range that extends to the negative supply rail, which eliminates external biasing components in many designs, and outputs that can swing close to ground without a negative rail. The internally compensated amplifiers need no external frequency-compensation parts, simplifying BOM and layout. The LM324S uses mature bipolar process technology, delivering stable, predictable behavior for low-frequency analog functions such as comparators, transducer amplifiers, DC gain blocks, and active filters. Typical parameters for the LM324 family include a gain-bandwidth product around 1 MHz and low supply current per amplifier, making it a workhorse for cost-driven designs rather than high-speed or precision applications. Typical applications include transducer amplifier front ends in industrial sensing, DC gain blocks in power supplies and battery chargers, active RC filters in audio and control paths, and voltage comparator functions in household appliances and automotive accessories. The through-hole PDIP package suits prototyping, educational boards, and repair-driven industrial designs. Design consideration: keep closed-loop gains modest and signal frequencies well below the gain-bandwidth limit, and provide an output pull-down resistor if you need the output to reach true ground under load. This page adds value beyond the datasheet by synthesizing drop-in replacement options, application guidance, and sourcing information in one place.

RFQ Kontak
LM324WDT - Low-Power Quad Op Amp | STMicroelectronics | Industrial
LM324WDT

LM324WDT - Low-Power Quad Op Amp | STMicroelectronics | Industrial

STMicroelectronics LM324WDT is a low-power, general-purpose quadruple operational amplifier with four independent amplifiers, push-pull output capability, and a 14-pin SOIC package. The device operates from 3 V to 32 V on a single supply and combines four channels with low power consumption and low input bias current. Its 14-SO configuration supports common industrial signal-conditioning, control, sensing, and low-frequency analog circuits. A quad operational amplifier is a semiconductor containing four independent high-gain amplifier sections in one package. An operational amplifier compares voltages applied to its inverting and non-inverting inputs and drives its output according to the difference between them. The quad format belongs to the broader analog-amplifier hierarchy and can replace four separate single-channel amplifier packages when the channels do not require isolated supplies. The LM324WDT's principal features include four amplifier circuits, a push-pull output stage, low input bias current, low power consumption, and high open-loop voltage gain. The 3 V to 32 V operating-voltage range allows operation from regulated 5 V systems through higher industrial supply rails. Operating all four channels from one package also reduces board area, although common power and ground connections require careful layout planning. Internally, the device uses the widely established LM324 universal standard amplifier architecture with integrated phase-compensation capacitors. This architecture prioritizes low cost, broad supply-voltage compatibility, and ease of general-purpose analog design rather than the very low offset, low noise, high speed, or rail-to-rail output characteristics found in precision amplifiers. The push-pull output structure supports bidirectional output drive within the available supply limits. Typical uses include low-frequency sensor amplification, transducer signal conditioning, current-to-voltage conversion, voltage comparison, basic active filtering, control-loop amplification, and general instrumentation. The four channels can process related signals or perform independent functions such as buffering, error amplification, summing, and threshold detection. For battery-operated or power-sensitive systems, the low-power architecture is especially useful when the required signal bandwidth remains modest. For stable operation, follow the manufacturer datasheet when selecting supply bypassing capacitors, handling input and output signals near the supply rails, and accommodating output-current limits. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined potential rather than left floating. The wide input and output common-mode limitations of the LM324 family should be checked before using it in high-side sensing or rail-to-rail signal chains. This page combines exact catalog information, pin-level implementation guidance, same-package replacement choices, and application-oriented design notes. It helps engineers determine whether the LM324WDT's four-channel, 3 V to 32 V general-purpose architecture is appropriate for a new design or an existing 14-SO PCB.

RFQ Kontak
LM339AD - Quad Differential Comparator | Texas Instruments
LM339AD

LM339AD - Quad Differential Comparator | Texas Instruments

The Texas Instruments LM339AD is a four-channel general-purpose differential comparator with open-collector outputs, supplied in a 14-pin SOIC package. The device supports a maximum rating of up to 38 V, an input offset voltage of 0.37 mV, input bias current of 3.5 nA, and supply current of 200 μA per comparator. According to the LM339A manufacturer datasheet, differential input voltage can equal the maximum-rated supply voltage of ±38 V, while the common-mode input range includes ground. A voltage comparator is an analog interface that compares two input voltages and changes its output state according to their relationship. The LM339 belongs to the comparator IC hierarchy within interface and signal-conditioning semiconductors. Unlike an operational amplifier used for closed-loop precision amplification, the LM339 provides open-loop decision making with relatively low output saturation voltage. Its four independent channels can monitor multiple thresholds, provide isolated sensing functions, or implement window and overvoltage detection. Key benefits include compatibility with TTL, MOS, and CMOS output systems, a supply-current requirement of 200 μA per comparator, and a response time listed as 1.3 μs in the manufacturer product details. These characteristics make the device appropriate for industrial control, power-supply supervision, sensor conditioning, and discrete logic interfaces. The open-collector outputs require an external pull-up resistor whenever a logic-high output is required. The LM339AD family is designed to operate from a single power supply over a wide voltage range. Its differential input rating of ±38 V and ground-inclusive common-mode capability provide useful margin in systems where the input signal can exceed the local logic supply. The A-grade designation distinguishes this version from the improved B family, whose enhanced specifications and operating current should be reviewed when designing a new design. Typical uses include overvoltage and undervoltage protection, zero-cross detection, temperature or light threshold switching, relay-drive logic, and four-channel sensing in industrial equipment. The 14-pin SOIC package permits compact board layouts and standard surface-mount assembly. For reliable implementation, place bypass capacitors near the supply pins and provide an appropriate pull-up resistor on every open-collector output. Confirm common-mode, differential, and output ratings against the actual signal range. Check input polarity and offset requirements when the decision threshold must remain accurate. This page combines manufacturer specifications, same-package replacement guidance, comparative parameters, and practical application guidance to support component selection and PCB design.

RFQ Kontak
LM339ADBR - 4-Channel 30V Open-Collector Comparator | Texas Instruments
LM339ADBR

LM339ADBR - 4-Channel 30V Open-Collector Comparator | Texas Instruments

Texas Instruments LM339ADBR is a four-channel differential voltage comparator operating from a single 2V to 30V supply, with an open-collector output stage and a 14-pin SSOP package. It provides a maximum rated supply voltage of 38V, an input offset voltage as low as 0.37mV, input bias current of 3.5nA, and supply current of 200µA per comparator. A quad differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when their difference crosses a defined threshold. The LM339 belongs to the comparator hierarchy within analog ICs and broader semiconductor signal-conditioning systems. Its four independent channels can compare unrelated signals because the devices share only power and ground connections. The open-collector outputs support wired-AND operation, level translation, and direct connection to pull-up resistors. Low input offset voltage of 0.37mV supports accurate switching decisions near the comparison threshold, while 3.5nA input bias current reduces source-loading effects in high-impedance sensing circuits. A 2V minimum supply permits operation from low-voltage rails, and the 30V operating range supports higher-voltage industrial systems. The B-version family also supports maximum ratings up to 38V. Each channel provides independent comparison inputs, allowing one device to implement four threshold, sorting, window-detection, or fault-monitoring functions. The open-collector architecture is useful when several comparator outputs must share a bus, although an external pull-up resistor is required for normal logic-high operation. Quiescent current of 200µA per comparator supports low-power monitoring systems when the device is operated near light-load conditions. Typical uses include industrial sensor monitoring, battery threshold detection, power-supply sequencing, overvoltage and undervoltage protection, window comparators, and logic interfaces. The low offset and bias-current characteristics are particularly useful when the source impedance and input voltage accuracy are important. The 14-pin SSOP package also supports compact board layouts where a larger SOIC or DIP package would be unnecessary. For reliable operation, select pull-up resistors according to the required rise time and sink-current budget, keep input and output paths separated to prevent switching transients from affecting comparisons, and observe the absolute maximum supply rating of 38V. The open-collector stage does not actively drive a logic-high state, so every application must include an appropriate pull-up arrangement or relay interface. This product record combines the electrical characteristics, package details, sourcing information, drop-in family options, and practical circuit guidance needed to evaluate the LM339ADBR in new comparator designs.

RFQ Kontak
LM339ADE4 - Quad Differential Comparator | Texas Instruments
LM339ADE4

LM339ADE4 - Quad Differential Comparator | Texas Instruments

Texas Instruments LM339ADE4 is a precision quad differential comparator containing four independent comparator channels, with a typical response time of 300 ns, a 2 V to 36 V supply range, and open-collector outputs in a 14-pin SOIC package. It supports single-supply or dual-supply operation and compares input signals across a common-mode range that includes ground. A differential comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference between them crosses a reference threshold. In the broader electronics hierarchy, the LM339 belongs to the comparator IC family, within linear integrated circuits and signal-conditioning systems. Its four channels allow one device to implement independent threshold detection, window comparison, zero-crossing detection, or level conversion without requiring four separate comparator packages. The principal features of the LM339ADE4 include four open-collector outputs, supply-voltage operation from 2 V to 36 V, and low supply-current drain of 0.8 mA typical. The output structure is compatible with TTL, MOS, and CMOS logic, making the device useful where a comparator must drive a pull-up resistor, relay driver, indicator, or digital logic input. Differential input voltage can reach ±38 V, while the common-mode input range includes ground. Internally, the LM339 uses four similar differential comparator sections operating from a common supply architecture. Because the outputs are open collector, each channel can sink logic-level current while remaining in a high-impedance state when inactive. An external pull-up resistor establishes the high output voltage. This architecture provides simple voltage translation and allows several open-collector outputs to share a bus when only one device is actively pulling the line low. Typical uses include industrial control and sensor interfaces, battery-powered monitoring, motor and actuator threshold detection, window comparators, overvoltage and undervoltage protection, and logic-level translation. The ability to operate from a single supply is particularly useful in portable systems because the input common-mode range includes ground. The 14-pin SOIC package also supports conventional surface-mount PCB assembly. Design the pull-up resistor for the required sink current, output rise time, bus capacitance, and available logic supply. Check input common-mode and absolute-maximum limits during startup because the input pins may briefly exceed the operating supply. Account for response delay when designing pulse-width or overvoltage systems; the typical 300 ns figure is a propagation-delay value rather than a guaranteed maximum. This product record combines the manufacturer’s device information with package, pinout, application, and drop-in replacement guidance. It supports faster design decisions by distinguishing the LM339A electrical architecture from B-version and alternate-family options, while emphasizing where open-collector pull-ups, supply range, and input operating limits require engineering review.

RFQ Kontak
LM339ADG4 - Quad Differential Comparator | Texas Instruments
LM339ADG4

LM339ADG4 - Quad Differential Comparator | Texas Instruments

Texas Instruments LM339ADG4 is a quad differential comparator containing four independent general-purpose comparator channels. Each channel compares two input voltages and drives an open-collector output, with a listed propagation delay of 300 ns. The device accepts a 2 V to 36 V single supply and can also operate from dual supplies when their total voltage falls within the specified range. It is packaged in a 14-pin SOIC for through-hole-era circuit compatibility and surface-mount assembly. A differential comparator is an analog integrated circuit that evaluates the relationship between two input voltages rather than operating as a conventional high-gain amplifier. If the non-inverting input is higher than the inverting input, the associated output transistor turns on; reversing the inputs changes the output state. The LM339 belongs to the comparator IC, analog comparator, and general-purpose semiconductor hierarchy used for threshold detection, level sensing, waveform conversion, and control decisions. The four open-collector outputs can sink current but require an external pull-up resistor to establish a high output voltage. This arrangement supports wired logic, relay or lamp drive, and interfacing with TTL, MOS, and CMOS circuits. The manufacturer identifies the device as a standard general-purpose comparator, while the listed 300 ns response time and 0.8 mA typical supply-current drain make it appropriate for circuits where propagation delay and supply demand are more important than nanosecond-class response. The wide 2 V to 36 V supply range supports industrial control, automotive-style interface circuits, power-supply monitoring, and legacy logic designs. A differential input range equal to the maximum-rated supply voltage allows substantial input swing around ground when suitable supply arrangements are used. The open-collector architecture is particularly useful when multiple comparator channels must share a pull-up or when the output must drive a device requiring more current than the comparator can source directly. Designers should pay close attention to common-mode input limits, output pull-up values, and the distinction between single- and dual-supply operation. Because the outputs are open collector, leaving them without a pull-up can produce an undefined logic level. Inputs and outputs should also be checked against the electrical limits in the manufacturer datasheet when operating near the 36 V maximum supply. This page brings together the verified LM339ADG4 specifications, package details, application guidance, same-footprint alternatives, and practical selection considerations. It is intended to help engineers confirm compatibility quickly while retaining the datasheet as the authoritative source for absolute maximum ratings, test conditions, and detailed timing behavior.

RFQ Kontak
LM339ADR - Quad Differential Comparator, SOIC-14 | Texas Instruments
LM339ADR

LM339ADR - Quad Differential Comparator, SOIC-14 | Texas Instruments

The Texas Instruments LM339ADR is a quad differential comparator with four independent voltage comparators, open-collector outputs, and a wide single-supply operating range of 2V to 36V, housed in a 14-pin SOIC package. A differential comparator is an analog component that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC family of analog signal-chain devices, positioned between operational amplifiers and dedicated level detectors in the system hierarchy. Unlike an op-amp, a comparator is designed for fast, saturated switching between two output states rather than linear amplification, making it the standard building block for threshold detection, zero-crossing detection, and analog-to-digital conversion front ends. Key features of the LM339ADR include a common-mode input voltage range that extends down to ground (V-), which permits sensing signals referenced to the negative rail without additional level shifting. The differential input voltage range equals the maximum-rated supply voltage of 36V, and the open-collector outputs can sink current to drive TTL, MOS, and CMOS logic directly while allowing wired-OR connections. Input bias current is low, on the order of nanoamperes (approximately 3nA per LCSC device data), keeping input source impedance requirements modest. Technically, the LM339 family uses a PNP differential input stage that allows operation from a single supply as low as 2V, or from dual supplies as long as the total supply difference is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. Per the TI LM339A product page, the B-version is a drop-in replacement for the LM239, LM339, and LM2901, and the device features a low output saturation voltage for efficient logic-level interfacing. Typical applications include threshold detectors in power-supply supervision, oscillators and multivibrators, window comparators in test equipment, and level shifting between analog sense circuits and digital controllers. The four comparators per package reduce board area and BOM line items in multi-channel monitoring designs. A key design consideration is that the open-collector outputs require external pull-up resistors; the LM339 cannot source current, and unused comparators should have inputs tied to defined rails to prevent oscillation. This page synthesizes distributor availability data, pin-compatible alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet alone.

RFQ Kontak
LM339ADR2 - Quad 18V/36V Comparator | ON Semiconductor | SOIC-14
LM339ADR2

LM339ADR2 - Quad 18V/36V Comparator | ON Semiconductor | SOIC-14

The ON Semiconductor LM339ADR2 is a quad differential comparator in a 14-pin SOIC tape-and-reel package. The manufacturer listing identifies it as a Quad Single Supply Comparator and a Comparator Quad 18V/36V, indicating operation from a single supply with high-voltage input capability. Four independent comparator channels provide a practical way to monitor multiple control, sensing, or protection signals without using four separate single comparator packages. A voltage comparator is an analog mixed-signal semiconductor that compares an input voltage with a reference voltage and produces a logic-level indication of their relationship. Quad comparators belong to the broader comparator and amplifier IC hierarchy, where they are used for threshold detection, overvoltage and undervoltage monitoring, signal conditioning, and control-system decision making. Their open-collector-style outputs are commonly associated with flexible system-level interfacing, although the exact output configuration should be confirmed in the manufacturer datasheet. The LM339ADR2's four-channel architecture gives designers independent comparator functions in one package. This can simplify analog front ends that compare a sensor signal against a configurable threshold, evaluate a feedback voltage, or supervise a system rail. The 14-pin SOIC package provides a conventional surface-mount footprint suitable for automated assembly, while tape-and-reel packaging supports standard production handling. The LM339ADR2 family is associated with an 18 V/36 V comparator rating and single-supply operation. These figures make the device relevant to industrial, automotive-style, and embedded control systems where input voltages can exceed the common rail of many low-voltage comparators. Designers must still observe the exact common-mode, differential-input, supply-voltage, output-current, and absolute-maximum limits listed for this exact orderable device. Typical uses include DC overvoltage detection, undervoltage supervision, window comparison, sensor thresholding, and industrial control interfaces. In these applications, each comparator can compare a monitored voltage against a reference, while an external pull-up may establish the digital output state when the comparator output is inactive. The comparator is especially useful when a system needs a simple, robust indication rather than a high-speed amplified analog signal. For implementation, begin with the manufacturer's pin-description and electrical-characteristics tables, then connect input, output, ground, and supply pins exactly as specified. Keep sensitive reference and feedback traces short, place input and supply bypassing capacitors close to the device, and check whether the selected logic family and output pull-up arrangement satisfy the system requirements. This page combines the verified manufacturer-oriented part listing, package information, comparison candidates, and practical integration guidance. It distinguishes documented facts from parameters that still require confirmation from the exact LM339ADR2 datasheet, helping engineers plan sourcing and schematic review without relying on a different package variant by mistake.

RFQ Kontak
LM339ADRE4 - Quad Differential Comparator | Texas Instruments
LM339ADRE4

LM339ADRE4 - Quad Differential Comparator | Texas Instruments

Texas Instruments LM339ADRE4 is a four-channel differential comparator with an open-collector output, a 2 V to 36 V supply range, and a 14-lead SOIC package. Each channel can compare two input voltages, making the device suitable for threshold detection, level sensing, window comparison, and control-system feedback. The comparator family operates from single or dual supplies and provides output compatibility with TTL, MOS, and CMOS logic. A comparator is an analog interface integrated circuit that determines whether one input voltage is above or below another voltage. The LM339ADRE4 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Unlike an operational amplifier intended mainly for closed-loop amplification, it is optimized for fast, saturated logic-level decisions. Four independent comparators in one package reduce component count and simplify designs requiring several sensing thresholds. The LM339 family provides a low input offset voltage of 0.37 mV, an input bias current of 3.5 nA, and supply current of 200 µA per comparator. Its response time is listed as 300 ns, making it suitable for many industrial, instrumentation, and control applications. The open-collector outputs can sink current and require an external pull-up resistor, allowing the output voltage to be set by the logic supply connected to the pull-up network. The maximum voltage rating reaches 38 V, while the normal operating supply range extends from 2 V to 36 V. Differential input voltage can approach the maximum-rated supply voltage, and the common-mode input range includes ground. This makes the device useful in single-supply sensing circuits where one signal remains near 0 V, as well as in dual-supply comparator arrangements using positive and negative rails. Typical uses include overvoltage and undervoltage detection, industrial sensor interfaces, battery monitoring, temperature threshold circuits, zero-cross detection, and control-loop limit sensing. Four channels allow a compact implementation of window monitoring or multiple independent threshold decisions. The open-collector architecture also supports wired logic when a shared pull-up is used under suitable system conditions. Designers should place input and output components close to the device, account for the open-collector pull-up network, and verify input common-mode and differential voltage limits. Because the outputs are open collector, they cannot source current independently. The pull-up resistor and its connected logic rail determine the high output voltage and rise time, making those values central to the overall switching design.

RFQ Kontak
LM339ADRG4 - Quad Open-Collector Comparator | Texas Instruments
LM339ADRG4

LM339ADRG4 - Quad Open-Collector Comparator | Texas Instruments

Texas Instruments LM339ADRG4 is a quad differential analog comparator with four independent comparison channels, an open-collector output, up to 300 ns response time, and a 2 V to 36 V supply-voltage range, housed in a 14-pin SOIC package. The device is intended for general-purpose voltage-threshold detection where one input voltage is compared with another and a logic-level decision is required. An analog comparator is an integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The LM339 family belongs to the broader comparator and signal-conditioning hierarchy, where comparator ICs support threshold detection, sensing, switching, waveform shaping, and simple control loops in industrial, automotive, and consumer electronics systems. Each LM339ADRG4 channel provides independent input comparison and an open-collector output. Open-collector outputs require an external pull-up resistor, allowing the output stage to sink current while leaving the pulled-up voltage under the system designer’s control. This architecture is useful with 5 V, 3.3 V, or other logic levels and supports wired-interface arrangements when multiple outputs share a common pull-up. The wide supply range permits operation from a single supply or from split dual supplies, provided the total supply span remains within the device limits. The low typical supply-current drain of 0.8 mA is independent of supply voltage, which can help limit consumed power in continuously operating equipment. The common-mode input range includes ground, supporting sensing near the lower supply rail in single-supply systems. Typical applications include industrial sensor-threshold circuits, battery and power-supply monitoring, automotive interface and control modules, window or level detection, general-purpose logic threshold conversion, and embedded systems that compare an analog measurement against a reference voltage. Its four independent channels also allow multiple comparisons to be implemented in one package while reducing board area. When designing around the open-collector outputs, select a pull-up resistor that satisfies the required sink current, rise time, and logic-level limits. Account for input offset, common-mode range, and supply headroom when setting a switching threshold. Do not assume that an open-collector output actively drives a high voltage; the external pull-up establishes the high state. This page combines manufacturer and distributor technical information, package-aware alternatives, comparison parameters, and practical design guidance for engineers evaluating the LM339ADRG4. It supports faster component selection while keeping procurement details, replacement constraints, and implementation considerations in one focused reference.

RFQ Kontak
LM339AM - Quad Open-Collector Comparator | Texas Instruments
LM339AM

LM339AM - Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM339AM is a low-power, low-offset, quad differential voltage comparator with four independent comparison channels, an open-collector output stage, and a 14-pin SOIC package. The device supports input voltages spanning ground in the common-mode range, a differential input rating up to 38 V, and compatibility with DTL, MOS, TTL, and CMOS logic families. Its specified operating-temperature range for this ordering code is 0°C to 70°C. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. The LM339 belongs to the voltage-comparator hierarchy, which falls within analog and mixed-signal ICs and ultimately the broader semiconductor category. Its four channels can operate independently or be configured as two window or hysteretic comparison functions. Key features include four open-collector outputs, low quiescent current, low input offset voltage, and wide input-voltage capability. The open-collector architecture requires an external pull-up resistor and permits several open-collector outputs to share a wired bus when their device-current limits and logic levels are compatible. The 14-pin SOIC package supports conventional surface-mount assembly while providing separate inputs, outputs, and two ground pins. Internally, each channel uses a differential input stage followed by an open-collector output stage. The inputs can be driven near ground, making the device suitable for low-level sensing where the signal of interest lies close to the lower supply rail. Because the outputs are open collectors rather than push-pull outputs, output rise time depends on the pull-up resistor, bus capacitance, and leakage current rather than only on the comparator itself. Typical applications include battery threshold detection, sensor-level conditioning, window comparators, industrial control interfaces, and low-level memory or control monitoring. Industrial systems benefit from the wide common-mode capability, while consumer and communication equipment can use the open-collector outputs directly with pull-up resistors. Four independent channels also reduce the component count in multi-level or multi-signal designs. Designers should verify supply voltage, input common-mode limits, output pull-up values, and propagation delay under the intended load. The open-collector output must never be left without a pull-up path, and unused comparator inputs should be tied to a defined potential to prevent unintended switching. PCB placement should keep pull-up resistors close to the output pins and minimize routing through noisy analog or switching nodes. This page combines the supplied manufacturer and distributor information with practical pin, replacement, application, and design guidance. It also distinguishes verified ordering information from details that must still be confirmed against the manufacturer datasheet before production release.

RFQ Kontak
LM339AM/NOPB - Low-Power Quad Comparator | Texas Instruments
LM339AM/NOPB

LM339AM/NOPB - Low-Power Quad Comparator | Texas Instruments

Texas Instruments LM339AM/NOPB is a low-power, low-offset quad voltage comparator containing four independent comparison channels in a 14-pin SOIC (D) package. Each comparator supports an input voltage range of 2 V to 36 V, a maximum differential input range of ±18 V, and an open-collector output. The device provides a response time of 1.3 µs, input offset voltage as low as 2 mV maximum across all four comparators, and supply current of 1 mA. A voltage comparator is an analog interface IC that compares two input voltages and produces a digital-level indication of their relationship. In the signal-chain hierarchy, the LM339 belongs to the comparator family within analog and mixed-signal ICs, where it bridges low-level sensing, threshold detection, protection, and logic-level conversion. Its four independent channels allow one package to implement several sensing or protection functions without requiring four separate single-channel devices. The principal features of the LM339AM/NOPB are its low operating power, wide supply-voltage tolerance, open-collector outputs, and broad output compatibility. Open-collector outputs can sink current and require an external pull-up resistor, allowing the output voltage to be set by the connected logic supply. The outputs are compatible with CMOS, DTL, ECL, MOS, and TTL circuits according to the manufacturer information. The 0 °C to 70 °C temperature range identifies this ordering code for commercial-temperature applications. Each of the four channels operates independently, allowing separate reference, threshold, or protection tasks within the same package. The 1.3 µs response time is suitable for general-purpose detection rather than high-speed timing applications. The 2 mV maximum offset specification for the complete quad is important when the difference between two sensed voltages is small. A wide 2 V to 36 V operating range also supports both low-voltage logic systems and higher-voltage industrial sensing environments when the external circuit and device ratings permit. Typical uses include power-supply sequencing, battery monitoring, sensor threshold detection, overvoltage and undervoltage indication, level translation, and simple control-loop sensing. Because the outputs are open collector, pull-up resistors are required when the outputs drive CMOS or TTL inputs. Open-collector stages can also be wired for wired-AND behavior where suitable, although the application must remain within the electrical ratings of every connected channel. Designers should verify input common-mode range, differential voltage, supply current, and output pull-up requirements against the manufacturer datasheet before implementation. Keep sensitive comparator inputs away from switching nodes and high-current return paths, use a stable reference when threshold accuracy matters, and select resistor values that provide adequate logic-high voltage while keeping output current within the channel limit. The 14-pin SOIC package supports conventional PCB assembly, but exposed-pad or other package variants require different layouts.

RFQ Kontak
LM339AMX - Quad Low-Offset Voltage Comparator SOIC-14 | Texas Instruments
LM339AMX

LM339AMX - Quad Low-Offset Voltage Comparator SOIC-14 | Texas Instruments

The Texas Instruments LM339AMX is a low-power, low-offset-voltage quad differential comparator with four independent open-collector output comparators housed in a 14-pin SOIC (3.90 mm width) surface-mount package. It operates from a single supply of 2 V to 36 V or dual supplies of ±1 V to ±18 V, and the common-mode input voltage range extends to include ground. A differential comparator is a mixed-signal building block that compares two input voltages and drives its output to indicate which is higher. Comparators sit within the broader amplifier and analog IC hierarchy, alongside operational amplifiers, but are optimized for fast switching and saturated logic-level outputs rather than linear operation. Because the LM339A family includes ground in its common-mode range, it can sense signals near zero volts on a single rail. Key features include four independent comparators in one package, wide single-supply operation from 2 V to 36 V (or ±18 V dual), low typical supply current drain of about 800 uA, and outputs compatible with TTL, DTL, MOS, and CMOS logic. The open-collector output stage allows wired-OR connections and level shifting to arbitrary logic voltages via a pull-up resistor. Low input offset voltage and operation with the input common-mode range including ground make the device suitable for near-ground sensing. Technically, the open-collector output transistors saturate at a low voltage, giving clean logic-level transitions and easy interfacing. A typical response time of approximately 1.3 us suits threshold detection, level translation, and oscillator circuits rather than ultra-high-speed applications. Typical applications include limit comparators, simple analog-to-digital converters, pulse generators, square-wave and relaxation oscillators, window detectors, and voltage monitoring in industrial and consumer systems. For design, remember that every output requires an external pull-up resistor since the output stage is open-collector, and inputs must be kept within the common-mode range even beyond the supply voltage specified in the absolute maximum ratings for differential input. This page adds value beyond the manufacturer datasheet by synthesizing distributor sourcing information, drop-in alternatives, comparison tables, and practical design notes in one place.

RFQ Kontak
LM339AMX/NOPB - 4-Comparator 36V IC | Texas Instruments
LM339AMX/NOPB

LM339AMX/NOPB - 4-Comparator 36V IC | Texas Instruments

Texas Instruments LM339AMX/NOPB is a four-channel, general-purpose voltage comparator IC with open-collector outputs, a 2 V to 36 V supply range, and a 14-pin SOIC package. The device provides a 1.3 µs response time and low input offset voltage, making it suitable for level detection, low-level sensing, memory applications, and general industrial control circuits. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when the differential input crosses a defined threshold. The LM339 family belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Each of its four channels can operate independently, while common power and ground connections simplify implementation across multiple sensing or control functions. The principal features of the LM339AMX/NOPB include four precision comparators, open-collector outputs, single-supply or dual-supply operation, and low power consumption. Its input offset voltage can be as low as 2 mV maximum for all four comparators. The open-collector architecture allows output transistors to be pulled up to a chosen logic voltage, enables wired-AND behavior, and permits use with CMOS, MOS, TTL, DTL, and ECL interfacing when suitable external pull-up circuitry is used. The LM339 architecture is designed for a broad supply range of 2 V to 36 V, or approximately ±1 V to ±18 V in dual-supply operation. A typical response time of 1.3 µs provides adequate speed for threshold detection, overvoltage monitoring, and simple control loops. Because each comparator is electrically independent, unused channels should be configured according to the manufacturer's input and output recommendations to prevent unstable behavior. Typical applications include industrial sensor interfaces, battery and power-supply monitoring, window and level comparators, control-system threshold detection, and low-level sensing. The wide supply range supports both compact low-voltage systems and higher-voltage industrial environments, while the 14-pin SOIC package supports conventional through-hole assembly and automated board assembly. A key design consideration is the open-collector output: every channel requires an external pull-up resistor unless the output is intentionally connected to a wired bus. Select the pull-up voltage to match the receiving logic family, and account for its contribution to supply current and switching speed. This page combines manufacturer specifications, package information, pin assignments, application guidance, and engineering-oriented comparisons to support component selection and PCB implementation.

RFQ Kontak
LM339AN - Quad Open-Collector Comparator | Texas Instruments
LM339AN

LM339AN - Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM339AN is a four-channel general-purpose differential voltage comparator with an open-collector output, a 2 V to 36 V supply range, and a 14-pin PDIP package. Each channel supports single-supply or split-supply operation, while the 1.3 µs response time suits general detection and threshold-control applications. The LM339A family provides a maximum input offset voltage of 2 mV and can operate with input voltages extending to ground on the negative supply. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM339AN belongs to the comparator family within analog and amplifier ICs, which sits within the broader integrated-circuit and semiconductor hierarchy. Its four independent channels allow multiple sensing, protection, or control functions to share one package without requiring four separate comparator devices. Key features include four independent comparators, open-collector outputs, 2 V to 36 V operating supply voltage, ±1 V to ±18 V differential input capability, and a 1.3 µs response time. The open-collector architecture provides flexible output interfacing because each output can pull a logic rail low through an external pull-up resistor. This arrangement works with TTL, CMOS, and MOS-compatible logic, although it adds a pull-up component and can expose the output node to more noise when the resistor is weak. The LM339AN uses a low-power bipolar comparator architecture optimized for general-purpose level detection rather than high-speed precision instrumentation. Its common-mode input range includes ground, making it useful in single 5 V or single 12 V systems where a signal approaches zero volts. The 2 mV maximum offset specification for the LM339A family helps limit transition-point error, while the 1.3 µs response time provides useful speed for relay, lamp, and simple control-loop decisions. Typical applications include sensor threshold detection, overvoltage and undervoltage protection, battery monitoring, industrial control inputs, window or level comparators, and general logic interfacing. Four channels can monitor four related signals independently, making the device suitable for multi-parameter protection boards and compact industrial interface modules. The open-collector outputs can drive a relay driver, an optocoupler, a status LED, or a logic input when an appropriate pull-up resistor is installed. Designers should treat all unused input pins carefully, provide adequate input-common-mode headroom, and select a pull-up resistor that balances speed, power, and noise performance. Because the outputs are open collector, multiple LM339AN channels may share a common pull-up node when their wired-OR behavior is acceptable. PCB creepage, grounding, and the relationship between the measured signal and the comparator threshold are equally important for reliable industrial operation. This page combines the verified manufacturer and distributor information for the LM339AN with package-specific pin mapping, transparent sourcing, and practical design guidance. It also distinguishes direct same-package alternatives from the broader LM339 family, helping engineers evaluate replacement options without confusing electrical equivalence with guaranteed mechanical or temperature-grade equivalence.

RFQ Kontak
LM339AN/NOPB - Quad Open-Collector Comparator | TI
LM339AN/NOPB

LM339AN/NOPB - Quad Open-Collector Comparator | TI

Texas Instruments LM339AN/NOPB is a low-power, low-offset-voltage quad differential comparator with four open-collector outputs in a 14-pin PDIP package. Each comparator supports input common-mode operation from ground to 36 V and can operate from a single supply or split ±18 V supplies, making it suitable for industrial control, sensing, and interface circuits. The package measures 0.3 inch wide and supports insertion-style PCB mounting. A differential voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM339 belongs to the comparator hierarchy within analog interface ICs and power-management systems. Its four independent channels let one package implement several threshold, window, overvoltage, or polarity decisions while sharing a common supply and ground. Each LM339 channel provides low-offset operation, low input bias current, and an open-collector transistor output. Open-collector outputs permit wired AND or NOR logic, use pull-up resistors, and can directly interface with TTL, MOS, and CMOS-compatible inputs. The ability to set a rising or falling threshold with external resistors makes the device useful for both positive-going and negative-going decisions. The architecture contains four independent comparator sections rather than a shared digital control interface. Because the outputs are open collector, output speed depends on the pull-up resistance, load capacitance, transistor sink current, and the time required to discharge the load node. Low output voltage and a small number of external components also make the LM339 practical where the logic load is tolerant of a passive pull-up network. Typical uses include DC voltage threshold detection, temperature-sensor signal conditioning, battery and power-supply monitoring, motor or relay control, window comparators, and industrial sensor interfaces. The 14-pin PDIP package is especially useful for through-hole assemblies, prototype boards, repair work, and designs where socketed or manually inserted components simplify maintenance. When assigning inputs, keep each noninverting and inverting connection within the comparator's permitted common-mode range, and do not allow the differential input to exceed the device's absolute maximum rating. Select a pull-up resistor that provides adequate sink-current margin and a rise time compatible with the downstream logic. Because an open-collector output can remain off, the external pull-up also determines the inactive logic level. This product page combines the exact LM339AN/NOPB ordering information with package dimensions, pin assignment, practical interface guidance, and technically qualified substitution options. It supports faster component selection by showing where the part fits, which electrical details require confirmation from the manufacturer datasheet, and how candidate replacements differ in temperature grade or low-power behavior.

RFQ Kontak
LM339ANG4 - 4-Channel 30V Differential Comparator | Texas Instruments
LM339ANG4

LM339ANG4 - 4-Channel 30V Differential Comparator | Texas Instruments

Texas Instruments LM339ANG4 is a four-channel differential comparator integrated circuit with an open-collector output architecture, a 2 V to 30 V single-supply range, and a 14-pin through-hole DIP package. Each of its four independent comparator channels compares two input voltages and provides a logic-level indication of their relationship, making the device suitable for threshold detection, level translation, sensing, and industrial control functions. A comparator is an analog integrated circuit that converts the relationship between two voltages into a digital output state. The LM339 belongs to the comparator IC family, within the broader hierarchy of analog semiconductor and signal-conditioning devices. Unlike a general-purpose operational amplifier used primarily for closed-loop amplification, a comparator is optimized to determine whether one input is above or below another, commonly for sensing and switching applications. The four-channel architecture reduces the number of packages and PCB connections needed for multi-threshold systems. Key characteristics include a maximum input offset voltage of 3 mV at 30 V, maximum input bias current of 0.25 µA at 5 V, and typical output current capability of 20 mA. The open-collector outputs can sink current for driving pull-up networks and interfacing with TTL, MOS, and CMOS-compatible logic, although an external pull-up resistor is required. The device accepts a wide single-supply operating range of 2 V to 30 V and a dual-supply range of ±1 V to ±15 V. This voltage tolerance makes it useful in industrial, automotive-adjacent, instrumentation, and embedded systems where sensing nodes may exceed ordinary low-voltage logic rails. The A-version LM339ANG4 is identified in the manufacturer documentation as an active quad differential comparator in a 14-DIP package measuring 0.300 inch, or 7.62 mm, across the lead row. Typical applications include DC overvoltage and undervoltage detection, sensor threshold switching, window comparators, relay-control interfaces, battery monitoring, and four-channel process-signal conditioning. Because the outputs use open-collector transistors, pull-up resistors can be selected to match the voltage and current requirements of the following logic family. The shared supply architecture also simplifies dual-polarity sensing around ground. Designers should verify input common-mode limits, output pull-up values, and channel-to-channel behavior before implementation. Input protection, filtering, and hysteresis may be required when sensed signals contain noise or when the comparator output must remain stable around a switching threshold. The 14-pin DIP through-hole package also provides ample spacing for hand assembly, prototyping, and serviceable industrial electronics. This product page combines the manufacturer device information with practical application guidance, package-level design considerations, and a structured comparison of compatible quad comparator options for easier component selection and PCB planning.

RFQ Kontak
LM339ANSRG4 - 4x Open-Collector Comparator | Texas Instruments
LM339ANSRG4

LM339ANSRG4 - 4x Open-Collector Comparator | Texas Instruments

Texas Instruments LM339ANSRG4 is a quad differential comparator containing four independent voltage comparators, an input voltage range of 2 V to 36 V, and open-collector outputs in a 14-pin SOIC package. The device can also operate from dual supplies of ±1 V to ±18 V, making it suitable for industrial and control circuits that compare signals above conventional logic levels. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. The LM339 belongs to the comparator IC hierarchy, where it combines differential analog input handling with digital-compatible open-collector outputs. Unlike a comparator with a fixed push-pull output, the open-collector architecture allows multiple outputs to be wired together when suitable pull-up circuitry is provided. Each of the four comparator channels has independent inputs and output. Key operating characteristics include a maximum input offset voltage of 3 mV at 30 V, input bias current of 0.25 µA at 5 V, and typical output current of 20 mA. The wide supply range permits operation from a single 2 V to 36 V source or from dual rails spanning ±1 V to ±18 V. A nominal 800 µA supply-current drain supports low-power operation when the system does not require continuous high-current output sinking. The open-collector output stage is the core architectural feature. Each transistor output can pull a logic net low while an external resistor supplies the high state, allowing interface with TTL, CMOS, MOSFET, relay, or other open-collector peripherals. This arrangement also permits wired-AND behavior across several channels. The output transistor must never be allowed to float because no internal pull-up resistor is present in the output path. Typical uses include industrial threshold detection, sensor signal conditioning, battery monitoring, overvoltage detection, window comparators, oscillator and relaxation timing circuits, and control logic for relays or power stages. The broad supply range is particularly useful in 12 V or 24 V industrial systems where the comparator inputs can tolerate voltages above the logic supply level. Layout should keep input traces short, maintain a stable ground reference, and place pull-up resistors close to the output nets. Because open-collector outputs can switch relatively large currents, check the absolute-maximum output voltage and current limits before driving a load. A pull-up resistor that is too large produces slow rising edges, while an undersized resistor can exceed the output-current limit. This page organizes the electrical limits, pin mapping, drop-in alternatives, application guidance, and design trade-offs of the LM339ANSRG4. It also identifies the important distinction between the obsolete ordering code and currently documented alternatives before a PCB design is revised.

RFQ Kontak
LM339APW - Quad Differential Comparator, TSSOP-14 | Texas Instruments
LM339APW

LM339APW - Quad Differential Comparator, TSSOP-14 | Texas Instruments

The Texas Instruments LM339APW is a quad differential comparator integrating four independent voltage comparators with open-collector outputs in a 14-pin TSSOP (PW) package. It operates from a single supply over a wide voltage range with a maximum rating up to 30 V for A-version devices, draws a low supply current of approximately 0.8 mA typical independent of supply voltage, and is characterized for operation from 0C to +70C. A differential comparator is an analog building block that compares two input voltages and drives its output to indicate which is higher. Within the signal-chain hierarchy, comparators sit alongside operational amplifiers in the amplifier IC family but are optimized for fast, saturated switching rather than linear amplification, making them core components in power management, level detection, and mixed-signal systems. Key features include a common-mode input voltage range that extends to ground (V-), which enables ground-referenced sensing from a single positive supply; a differential input voltage range equal to the maximum-rated supply voltage; low output saturation voltage for efficient driving of loads; and outputs compatible with TTL, MOS, and CMOS logic families. The four independent comparators allow quad-channel threshold monitoring in a single footprint. Architecturally, each comparator uses a PNP differential input stage that allows inputs to swing down to the negative rail, followed by gain and open-collector output stages that require an external pull-up resistor. Because outputs are open-collector, multiple comparator outputs can be wire-ORed for shared alarm or window-detector functions. Typical applications include overvoltage and undervoltage supervision, window comparators on power rails, oscillator and relaxation clock generation, analog-to-digital front ends such as flash-converter slicing, and level shifting between analog thresholds and digital logic. For design, always fit a pull-up resistor (typically 3 kOhm to 15 kOhm) on each open-collector output, and add hysteresis with positive feedback to prevent output chatter near slow-moving thresholds. This page adds value beyond the datasheet by combining drop-in cross-references, application guidance, comparison tables, and sourcing information in one engineer-oriented reference.

RFQ Kontak
LM339APWG4 - 4-Channel 30V Comparator | Texas Instruments
LM339APWG4

LM339APWG4 - 4-Channel 30V Comparator | Texas Instruments

The Texas Instruments LM339APWG4 is a four-channel differential comparator IC with open-collector outputs, operating from a single 2 V to 30 V supply or from split ±1 V to ±15 V supplies in a 14-pin TSSOP package. It compares two input voltages at each channel and produces a digital indication of their relationship. The part is intended for general-purpose industrial, consumer, and automotive-style signal-processing systems. A comparator is an analog interface IC that converts the relationship between two voltages into a logic-compatible output. The LM339 belongs to the wider comparator hierarchy, which sits between general-purpose analog signal conditioning and digital control. Each of its four independent channels includes a non-inverting input, an inverting input, and an open-collector output, allowing a system to monitor thresholds, detect crossings, or supervise external signals. Key features include a maximum rating of up to 38 V, a differential input range equal to the maximum-rated supply voltage, and operation with common-mode input voltage extending to ground. According to the Texas Instruments LM339 product page, the outputs are compatible with TTL, MOS, and CMOS logic. The open-collector architecture requires an external pull-up resistor and gives the designer control over rise time, output level, and wired-output behavior. The LM339 family is designed for single-supply or dual-supply operation, providing flexibility in industrial control, automotive electronics, and low-voltage systems. Its differential inputs support direct comparison of sensor outputs or two analog nodes, while the wide supply range permits use from modest single-rail systems through higher-voltage industrial environments. The A version provides tighter input characteristics than the standard LM339 variant, including a low input offset of 0.37 mV and low input bias current of 3.5 nA. Typical uses include level detection, window comparators, overvoltage monitoring, temperature-control loops, zero-cross detection, and low-level sensing. The four channels can also be arranged as two independent window comparators, or used for mixed tasks such as a sensor threshold, a supply supervisor, and a timing comparator within one package. Designers must account for the open-collector output and its pull-up network, verify the common-mode and differential input limits, and maintain adequate logic-level compatibility. Input protection, hysteresis for noisy analog signals, and stable bypassing of the supply rails are essential for reliable operation. Because the output is open collector, multiple channels or external devices can share a pull-up when their logic states do not conflict. This page combines the manufacturer’s device description, verified distributor specifications, lifecycle information, same-package replacement guidance, and practical design notes. It helps engineers identify whether the LM339APWG4 fits a four-channel open-collector design while distinguishing it from newer dual-channel, rail-to-rail, and push-pull comparator families.

RFQ Kontak
LM339APWR - Quad Differential Comparator | Texas Instruments
LM339APWR

LM339APWR - Quad Differential Comparator | Texas Instruments

The Texas Instruments LM339APWR is a quad differential comparator containing four independent open-collector comparator channels in a 14-pin TSSOP package. It supports single-supply or split-supply operation, accepts input common-mode voltages that include ground, and provides open-collector outputs compatible with TTL, MOS, and CMOS logic. Key ratings include a maximum rated supply of 38 V, differential input voltage of ±38 V, input offset voltage as low as 0.37 mV, input bias current of 3.5 nA, and response time of 1 µs. A comparator is an analog-to-digital decision element rather than an amplifier: it evaluates a voltage at its non-inverting input relative to its inverting input and changes its output state when the difference crosses a defined threshold. Within the power-management and signal-conditioning hierarchy, the LM339A belongs to the comparator family of integrated circuits. Its four channels can perform independent threshold decisions, while its open-collector outputs allow wired logic, pull-up-controlled buses, or interface to subsequent digital stages. The principal features of the LM339APWR include four independent channels, low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, and low supply-current consumption of 200 µA per comparator. Its common-mode input range includes ground, which is important for single-supply sensing systems. The 1 µs response time supports practical threshold and protection functions, while the 38 V maximum rating provides additional operating margin in industrial systems. Each comparator uses an open-collector output structure, so the output includes a transistor capable of sinking current rather than actively driving a rail-to-rail logic voltage. A pull-up resistor is therefore required to establish the high output state. This architecture is useful when multiple devices must share a wired signal, but it also introduces rise-time behavior governed by the pull-up resistance and total bus capacitance. Typical applications include industrial sensor conditioning, battery-powered monitoring, overvoltage and undervoltage detection, window-comparison circuits, and control systems with open-collector alarm outputs. The common-mode range including ground makes the device suitable for detecting small signals near 0 V, while the multi-channel configuration allows one package to implement several related thresholds. Designers should account for input and output behavior near ground, select an appropriate pull-up resistor, and verify operation across supply tolerance, temperature, input overvoltage, and output leakage conditions. Review the Texas Instruments datasheet pin-description table before assigning PCB signals, especially because the exposed supply and output arrangement is specific to the quad TSSOP implementation. This product page combines the manufacturer’s electrical and ordering information with practical design guidance, same-footprint replacement analysis, and application-oriented context. It is intended to help engineers identify whether the LM339APWR’s four-channel, open-collector architecture fits a comparator design before beginning PCB implementation or production sourcing.

RFQ Kontak
LM339APWRG4 - Quad Open-Collector Comparator | Texas Instruments
LM339APWRG4

LM339APWRG4 - Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM339APWRG4 is a general-purpose quad differential comparator containing four independent comparators in a 14-pin TSSOP package. Each comparator supports single-supply or split-supply operation, and the device uses open-collector outputs for flexible interfacing with TTL, MOS, and CMOS logic families. A comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM339 belongs to the comparator hierarchy, which sits alongside amplifiers, analog switches, and sensors as a core building block for signal conditioning. Its differential inputs detect threshold crossings, overvoltage events, zero-crossing points, and magnitude comparisons in control and monitoring circuits. The LM339APWRG4 provides four comparison channels, a supply-voltage operating range extending to 36 V, a typical supply-current drain of 0.8 mA, and a low typical input bias current. Its open-collector outputs require an external pull-up resistor and permit the output stage to be pulled to the voltage required by the attached logic system. The wide operating range makes the device suitable for industrial control, power-supply monitoring, and interface conversion circuits. The four channels share a common ground and supply connection but otherwise operate independently. Differential input voltage can be handled over a range equal to the maximum-rated supply voltage, while the common-mode input range includes ground. This architecture is useful when sensing small changes around a ground-referenced signal or when one input is tied to a precision threshold reference. Typical applications include four-channel level detection, window comparison, battery and power-rail supervision, zero-crossing detection, sensor interfacing, and TTL-to-CMOS translation. In each case, the open-collector output can sink current from a pull-up network while leaving the logic voltage independent of the comparator supply. When designing around the LM339APWRG4, place the pull-up resistor close to the driven logic input and route comparator inputs away from switching nodes and high-current traces. Because open-collector outputs cannot actively source current, account for the pull-up value when setting rise time. Confirm the input common-mode range and output timing against the system operating limits before releasing the layout. This page combines manufacturer specifications, package and pin information, practical application guidance, and drop-in replacement analysis to support faster component selection and PCB-level implementation planning.

RFQ Kontak