LM324WDT - Low-Power Quad Op Amp | STMicroelectronics | Industrial
MPN: LM324WDT ✗ Tapus ng BuhayLM324WDT Ulas
A quad operational amplifier is a semiconductor containing four independent high-gain amplifier sections in one package. An operational amplifier compares voltages applied to its inverting and non-inverting inputs and drives its output according to the difference between them. The quad format belongs to the broader analog-amplifier hierarchy and can replace four separate single-channel amplifier packages when the channels do not require isolated supplies.
The LM324WDT's principal features include four amplifier circuits, a push-pull output stage, low input bias current, low power consumption, and high open-loop voltage gain. The 3 V to 32 V operating-voltage range allows operation from regulated 5 V systems through higher industrial supply rails. Operating all four channels from one package also reduces board area, although common power and ground connections require careful layout planning.
Internally, the device uses the widely established LM324 universal standard amplifier architecture with integrated phase-compensation capacitors. This architecture prioritizes low cost, broad supply-voltage compatibility, and ease of general-purpose analog design rather than the very low offset, low noise, high speed, or rail-to-rail output characteristics found in precision amplifiers. The push-pull output structure supports bidirectional output drive within the available supply limits.
Typical uses include low-frequency sensor amplification, transducer signal conditioning, current-to-voltage conversion, voltage comparison, basic active filtering, control-loop amplification, and general instrumentation. The four channels can process related signals or perform independent functions such as buffering, error amplification, summing, and threshold detection. For battery-operated or power-sensitive systems, the low-power architecture is especially useful when the required signal bandwidth remains modest.
For stable operation, follow the manufacturer datasheet when selecting supply bypassing capacitors, handling input and output signals near the supply rails, and accommodating output-current limits. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined potential rather than left floating. The wide input and output common-mode limitations of the LM324 family should be checked before using it in high-side sensing or rail-to-rail signal chains.
This page combines exact catalog information, pin-level implementation guidance, same-package replacement choices, and application-oriented design notes. It helps engineers determine whether the LM324WDT's four-channel, 3 V to 32 V general-purpose architecture is appropriate for a new design or an existing 14-SO PCB.
Mga alternatibo na pwedeng ilagay na LM324WDT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM324WDT (parehas na form factor at footprint) — pagkakaiba sa Package, Amplifier Type, Input Offset Voltage, Supply Voltage Range, Operating Temperature Range.
LM324DT
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo✗ Wala sa Stock
$0.0827 / Yunit
Tingnan ang Datasheet →LM324QT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324DR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324ADR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324BAIDR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324WDT Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Channels | 4 channels |
| Type ng Output | Push-pull |
| Supply Voltage Range | 3 V to 32 V |
| Architecture | Quad operational amplifier |
| Input Bias Current | Low input bias current |
| Power Consumption | Low power consumption |
| Open-Loop Voltage Gain | High gain |
| Phase Compensation | Integrated capacitors |
| Packhaging | 14-SO SOIC |
| Bilang ng Pin | 14 pins |
| Uri ng Pagpapasok | Surface mount |
| Product Type | Low-power quad operational amplifier |
| Compliance | RoHS and REACH status not stated |
| Automotive Qualification | AEC-Q100 status not stated |
Pin Configuration ng LM324WDT
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | -IN1 — Amplifier 1 inverting input |
| Pin 3 | +IN1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | +IN2 — Amplifier 2 non-inverting input |
| Pin 6 | -IN2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | -IN3 — Amplifier 3 inverting input |
| Pin 10 | +IN3 — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | -IN4 — Amplifier 4 inverting input |
| Pin 13 | +IN4 — Amplifier 4 non-inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Tipikal na mga Gamit
LM324WDT ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Current-to-Voltage Conversion, Control-System Error Amplifier, Audio and Communication Buffering, Active Filtering and Summing, Battery-Powered Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM324WDT is well suited to low-frequency industrial sensor conditioning because four low-power amplifier channels can buffer, scale, and offset several related sensor signals on one board. Its 3 V to 32 V supply range supports 5 V instrumentation as well as higher-voltage industrial rails. Use one channel for the input amplifier and others for offset correction or active filtering. The designer must keep signals inside the LM324's specified common-mode and output-swing ranges, because the device is not rail-to-rail at input or output.
Inirekomenda
Current-to-Voltage Conversion
The LM324WDT can implement four current-to-voltage conversion or transimpedance stages when the required signal bandwidth is modest. Low input bias current helps reduce error when working with high-impedance sensors, while the four-channel architecture consolidates multiple measurements into one 14-SO package. Place the amplifier close to the sensing node to minimize leakage and parasitic capacitance, and add compensation appropriate to the feedback network. Verify stability with the intended source capacitance rather than relying only on nominal bandwidth.
Inirekomenda
Control-System Error Amplifier
The LM324WDT provides four low-power channels for error amplification, actuator feedback, threshold comparison, and auxiliary control functions in basic analog control systems. Its high open-loop gain supports closed-loop error correction, while the 3 V to 32 V supply range permits operation from low-voltage controls to higher-voltage industrial buses. Four channels reduce footprint compared with separate packages, but common ground and supply routing can couple noise between channels. Separate sensitive feedback routing from power-intensive actuator paths and use local supply bypassing.
Inirekomenda
Audio and Communication Buffering
The LM324WDT can serve as a general-purpose buffer or gain stage in line-level audio, communications, and other low-frequency analog systems. Its push-pull output stage drives the output in both directions more effectively than an open-collector implementation, while the four-channel format supports repeated buffering or mixing functions. The device is best suited to signals that remain within its input and output swing limits. Confirm noise, bandwidth, and slew-rate requirements for the highest-frequency channel before using it in precision audio paths.
Inirekomenda
Active Filtering and Summing
The LM324WDT can implement active filters, summers, difference amplifiers, and threshold detectors when low-to-moderate frequencies and simple gain settings are sufficient. Four independent channels permit a cascaded second-order filter, a summing stage, and two utility channels within one package. Passive component tolerances directly influence gain and cutoff accuracy, so use suitable resistor and capacitor tolerances for the required response. Keep the summing-node impedances balanced and avoid driving capacitive loads that could compromise stability.
Inirekomenda
Battery-Powered Portable Instrumentation
The LM324WDT is appropriate for portable, battery-powered instrumentation that needs several low-frequency analog channels and can operate from a compact supply. Its low-power operation and low input bias current help reduce consumption and loading from high-impedance sensors, while the four-channel package minimizes board area. The minimum 3 V operating supply supports energy-efficient embedded designs. For portable products, verify supply current across the complete output range and confirm that the input common-mode range includes the sensor's operating voltage.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM324WDT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM324DT | LM324QT | LM324DR | LM324ADR | LM324BA |
|---|---|---|---|---|---|---|
| Package | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Pangunahing mga Pagkakaiba
- Four independent amplifiers in one 14-SO package (kumpara saLM324DR)
- Single-supply operation across a wide voltage range (kumpara saLM324QT)
- Push-pull output stage for bidirectional drive (kumpara saLM324ADR)
- Low-power and low-input-bias characteristics (kumpara saLM324BA)
Talaan ng Disenyo
Place the required supply-decoupling capacitor immediately between pins 11 and 4, with a short and low-inductance return path. Because all four amplifiers share the same supply pins, supply disturbance can affect every channel simultaneously. Add a second local bypass capacitor when the manufacturer recommends it, and keep high-current return paths away from the sensitive input and feedback traces.
Route each non-inverting input, inverting input, and output directly to its associated circuit nodes. Keep feedback components close to pins 2, 6, 9, and 12 to minimize parasitic capacitance and feedback-loop area. Treat the exposed circuit board under the SOIC body as a thermal and electrical consideration even though this package does not use a dedicated exposed pad.
Do not assume that the 3 V to 32 V supply range also defines the usable input or output range. Check the common-mode input limits and output swing against the actual signal. Similarly, tie unused amplifier inputs to a defined bias voltage. Leaving an input floating can make the associated output unpredictable and may introduce instability into adjacent measurement circuits.
Use short traces for high-impedance sensor inputs and keep them away from supply and output routing. The LM324 family is intended primarily for low-frequency general-purpose operation, so high-gain layouts can amplify thermal noise and layout leakage. Select resistor values that avoid excessive loading and maintain feedback stability at the lowest expected signal frequency and the highest expected capacitive load.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer listings identify the LM324WDT as a general-purpose 14-SO amplifier but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.