Analog Devices

AD534JHZ - Precision 4-Quadrant Multiplier | Analog Devices

MPN: AD534JHZ ✓ Nakahanda
10-pin TO-100 Package
MOQ: 1 |

AD534JHZ Ulas

The Analog Devices AD534JHZ is a monolithic, laser-trimmed four-quadrant multiplier-divider with a 10-pin TO-100 package. Its internally adjusted scale factor is 10 V, while the manufacturer describes low output noise of 90 µV rms over a 10 Hz to 10 kHz bandwidth. The device combines a precision multiplier, differential input stage, and high-gain output amplifier in one analog IC intended for accurate analog signal processing.

A four-quadrant multiplier-divider is an analog multiplier that can multiply two signals in any combination of polarity. Unlike a fixed-gain amplifier, its output changes in proportion to two independently varying input voltages. Such devices are used to implement gain control, modulation, demodulation, squaring, signal inversion, analog computation, and feedback control functions where a variable transfer characteristic is required.

The AD534 uses monolithic construction with laser trimming to establish its scale factor and improve consistency between units. An on-chip buried Zener reference supports the precision internal scale factor of 10 V. The manufacturer identifies the AD534 as a production device and emphasizes long-term stability, precision calibration, and low-noise performance as central characteristics of the family.

Electrical operation depends on the relationship between the differential multiplier inputs and the denominator or reference input. In divider service, the reference input defines the normalization condition; in multiplier service, the output follows the product of the two signal inputs. Designers should preserve the input and output common-mode ranges, observe the supply limits, and provide stable reference and feedback paths to retain multiplication accuracy.

Typical uses include precision analog signal conditioning, industrial instrumentation, control-loop scaling, laboratory interface circuits, transducer excitation and return-path processing, modulation equipment, and custom analog-computation modules. The AD534 is especially appropriate when a fixed or trimmed multiplier must provide predictable scale-factor behavior without external calibration.

PCB implementation requires attention to analog grounding, supply bypassing, and the stability of high-gain feedback connections. The TO-100 package supports conventional through-hole mounting and provides a larger thermal path than a small surface-mount package, but it still needs adequate copper area and airflow when dissipating substantial power. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before layout.

This page combines the manufacturer product characterization, package information, pricing availability, application guidance, and engineering selection criteria in one reference. It also distinguishes documented AD534 family variants from true drop-in replacements so engineers can distinguish temperature-grade or package differences before approving a substitution.

Mga alternatibo na pwedeng ilagay na AD534JHZ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok AD534JHZ (parehas na form factor at footprint) — pagkakaiba sa Mounting Type.

Analog Devices
Mounting Type: Through Hole
Ikabit sa AD534JHZ →

Wala ng magagamit na drop-in alternatibo para sa produkto na ito.

Hilingin ang Alternatibo

AD534JHZ Mga Spesipikasyon

Product Type Monolithic four-quadrant multiplier-divider IC
Quadrant Capability 4 quadrants
Internal Scale Factor 10 V
Output Ng Gulo 90 µV rms, 10 Hz to 10 kHz
Noise Bandwidth 10 Hz to 10 kHz
Packhaging 10-pin TO-100
Bilang ng Pin 10 pins
Uri ng Pagpapasok Through-hole
Construction Monolithic
Calibration Method Laser trimmed
Internal Reference On-chip buried Zener reference
Production Status Production

Gabay sa Pin Configuration ng AD534JHZ 10-pin to-100

Pin configuration para sa AD534JHZ (10-pin to-100 package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 10-pin to-100 package para sa AD534JHZ

Wala ng detalyadong pinout data na magagamit para sa AD534JHZ.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

AD534JHZ ay nararapat para sa 6 aplikasyons: Precision Industrial Signal Scaling, Analog Modulation and Demodulation, Transducer Signal Conditioning, Control Loop Product Limiter, Laboratory Analog Computation, Test and Measurement Front End.

🏭

Precision Industrial Signal Scaling

The AD534JHZ fits industrial signal-scaling circuits that require the output to vary with the product of two control and process signals. Its four-quadrant operation accommodates positive and negative input combinations, while laser-trimmed construction supports repeatable calibration across units. The 10 V internal scale factor provides a defined multiplier reference, and the 90 µV rms noise specification from 10 Hz to 10 kHz is relevant when conditioning low-level transducer signals. Install the TO-100 device on a stable analog section of the controller board, keep feedback and reference paths short, and verify that both input ranges and the output remain within the grade-specific limits.

🌐

Analog Modulation and Demodulation

The AD534JHZ can implement analog modulation by multiplying a carrier or baseband waveform with a controllable amplitude signal. Four-quadrant multiplication supports phase reversals and bipolar control signals, while the monolithically constructed multiplier reduces the number of discrete precision elements required for modulation. Its stated 90 µV rms noise over 10 Hz to 10 kHz helps set the practical noise floor for low-level modulation paths. Keep the carrier and control inputs within their specified common-mode ranges, use a low-noise reference arrangement, and route the multiplier output with short, shielded analog traces to prevent external interference from adding to the intrinsic device noise.

🧩

Transducer Signal Conditioning

The AD534JHZ is applicable to transducer interfaces in which a sensor-derived signal must be scaled by a calibration or range factor. Dividing by a controlled reference allows the output to represent a normalized measurement, while multiplying by a correction coefficient supports calibration and unit conversion. The internally trimmed AD534 architecture provides a consistent 10 V scale factor, while the laser calibration supports manufacturing repeatability. Preserve the sensor excitation reference as a low-noise node, confirm the differential input range, and provide filtering separately when needed so that protection or anti-aliasing components do not introduce excess multiplier error.

⚡

Control Loop Product Limiter

The AD534JHZ can serve as a product-forming element in analog control and feedback systems where a command variable is multiplied by a plant variable or operating factor. Four-quadrant behavior permits sign reversal and bipolar command handling, and the 10 V internal scale factor simplifies calculation around the nominal reference. Because precision multiplication can amplify errors in both factors, keep the command and feedback paths balanced and observe the output range at worst-case load. The 90 µV rms device noise from 10 Hz to 10 kHz should be included in low-level loop-noise analysis, while higher-frequency filtering should be designed around the required loop bandwidth.

🔧

Laboratory Analog Computation

The AD534JHZ supports laboratory analog-computation modules that implement multiplication, squaring, inversion, or ratio functions without a digital processor. Its monolithic and laser-trimmed construction makes it suitable as the central precision element of a bench instrument, and its four-quadrant operation permits bipolar test signals. The 10 V scale factor provides a defined basis for calibration procedures. Use stable references, low-noise supplies, and short feedback loops, and calibrate the complete module because resistor tolerances and leakage outside the multiplier may contribute system error. The 90 µV rms noise figure is directly relevant to experiments conducted within the stated 10 Hz to 10 kHz bandwidth.

📺

Test and Measurement Front End

The AD534JHZ can form part of a precision test-and-measurement front end that applies programmable gain or normalization to an analog signal. Multiplication by a digitally derived control voltage allows the analog section to implement a digitally controlled scale without converting the measured quantity to a digital value first. The internally trimmed scale factor and low-noise construction help maintain calibration integrity, particularly when the measured signal is small. Keep the digitally controlled reference path free of switching transients, isolate sensitive analog routing from digital activity, and verify settling behavior against the bandwidth required by the measurement system.

What is the AD534JHZ?
The AD534JHZ is a monolithic, laser-trimmed four-quadrant multiplier-divider IC from Analog Devices in a 10-pin TO-100 package. According to the manufacturer data sheet, it uses an internal 10 V scale factor and provides four-quadrant analog multiplication, making it suitable for signal scaling, modulation, control, and analog-computation circuits. The laser trimming improves unit-to-unit consistency in the multiplier calibration.
What are the key specifications of AD534JHZ that engineers should know?
The AD534JHZ combines four-quadrant multiplication, a 10 V internal scale factor, 90 µV rms output noise from 10 Hz to 10 kHz, monolithic construction, and laser-trimmed calibration in a 10-pin TO-100 package. The Analog Devices data sheet also identifies an on-chip buried Zener reference. Supply limits, temperature range, accuracy grades, bandwidth, and common-mode limits must be selected from the corresponding grade and ordering information.
Where can I download the AD534JHZ datasheet PDF?
The official AD534JHZ data sheet is available from Analog Devices at the AD534 product-document URL used on this page. The document contains the device description, ordering information, electrical characteristics, pin assignments, application information, and performance curves. Use the manufacturer's PDF for wiring and design decisions, because third-party copies may contain older revisions or incomplete pin information.
Where can I find the AD534JHZ pinout?
Use the pin-description table in the Analog Devices AD534 data sheet to assign signals on the 10-pin TO-100 package. The public product characterization confirms a 10-pin TO-100 configuration, but a complete numbered pin list is not printed on the product page. Before routing a board or wiring a prototype, verify each lead against the data sheet revision corresponding to the ordered AD534 grade.
Is AD534JHZ suitable for precision analog signal conditioning?
Yes, the AD534JHZ is suitable for precision analog signal conditioning when its specified input and output ranges match the signal chain. Its four-quadrant operation handles positive and negative input combinations, while the manufacturer identifies a 10 V internal scale factor and laser-trimmed construction as principal precision features. The 90 µV rms noise figure applies over 10 Hz to 10 kHz and should be considered when designing low-level modulation paths.
How does the AD534JHZ differ from AD534JH?
AD534JHZ and AD534JH identify ordering variants within the same AD534 precision multiplier-divider family. The available comparison references confirm both variants but do not provide a complete grade-by-grade electrical table in their summaries. The suffix should therefore be checked against the manufacturer's ordering guide for package finish, temperature grade, and production status before treating one as an interchangeable substitute.
What is the best drop-in replacement for AD534JHZ?
No drop-in replacement can be confirmed from the available cross-reference records. A valid replacement must use the same 10-pin TO-100 footprint, preserve the four-quadrant multiplier-divider function, and meet the required accuracy, noise, supply, and temperature limits. AD534JH is a closely related family variant, but its ordering characteristics must be verified before it is approved as a drop-in substitute.
Can AD534JH replace AD534JHZ on an existing PCB?
AD534JH may be mechanically related to AD534JHZ, but mechanical similarity alone does not establish drop-in interchangeability. Confirm the complete TO-100 pin assignment, temperature grade, supply limits, accuracy class, calibration, and orderable suffix in the Analog Devices documentation. If any of those characteristics differ, treat the substitution as a new qualification rather than an automatic replacement.
When should I choose AD534JHZ instead of a discrete multiplier implementation?
Choose the AD534JHZ when a calibrated four-quadrant multiplier is required in a compact analog IC and the 10-pin TO-100 package is acceptable. Its monolithic construction, laser-trimmed calibration, internal 10 V scale factor, and specified 90 µV rms noise simplify implementation compared with a discrete multiplier built from multipliers, amplifiers, resistors, and trim networks. Confirm that the analog signal levels remain inside its operating limits.
What is the AD534JHZ noise performance?
The Analog Devices AD534 product page specifies output noise of 90 µV rms over a 10 Hz to 10 kHz bandwidth. This figure is relevant to low-level analog conditioning, modulation, and instrumentation because it defines the device's stated short-band noise performance. It should not be extended outside the stated frequency range, and system noise must also include references, feedback resistors, power supplies, and external amplifiers.
Is AD534JHZ an active or obsolete product?
The Analog Devices product page identifies the AD534 as a production device, so the family is represented as active for design-in purposes. Lifecycle status can vary by package or accuracy suffix, so engineers should verify the exact AD534JHZ ordering option and its lifecycle statement when preparing a production BOM. The family page is the appropriate starting point for current status confirmation.
Where can I buy AD534JHZ and what is the price?
Use the Request a Quote form on this page to request AD534JHZ pricing, stock confirmation, and lead time. The form supports exact-part sourcing without relying on a static price that may become outdated. Include your required quantity, package variant, target date, and any grade or inspection requirements so the quotation can be prepared for the correct ordering option.
What is the lead time for AD534JHZ?
Submit an AD534JHZ request through the Request a Quote form on this page to obtain the current lead time and stock position. Lead time can vary with order quantity, manufacturing conditions, and shipment destination. The product family is marked as production, but a current quotation remains the appropriate source for a specific procurement commitment.
Is AD534JHZ in stock?
Stock status for AD534JHZ should be confirmed through the Request a Quote form on this page. The form provides a direct route for current quantity, allocation, and delivery information for the exact ordering suffix. Avoid treating general marketplace presence as a firm stock guarantee because inventory can change independently for each package and grade.
What is the best Analog Devices equivalent for AD534JHZ?
The closest documented Analog Devices family alternative is AD534JH because it belongs to the same internally trimmed precision multiplier-divider product line. Its use as an equivalent depends on matching the TO-100 pinout, temperature grade, accuracy, supply limits, and lifecycle status. No unrelated amplifier or multiplier should be treated as a drop-in substitute without a documented pin-level and parametric comparison.

Impormasyon ng Talumpati sa Engineering for AD534JHZ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose AD534JHZ when the design requires a calibrated four-quadrant multiplier-divider with a defined 10 V internal scale factor and an integrated precision reference. It is well suited to industrial signal scaling, bipolar modulation, transducer normalization, analog computation, and precision control loops where a discrete multiplier would increase component count and calibration effort. The 10-pin TO-100 package favors through-hole or leaded construction rather than compact surface-mount designs.

Do not select a nominal AD534 family variant solely by its base number. AD534JH, AD534JD, and AD534SH appear in cross-reference results, but package construction, temperature rating, accuracy, and ordering characteristics must be checked before substitution. No cross-brand drop-in equivalent is established by the available manufacturer and distributor records. For designs requiring a smaller footprint, lower power, wider bandwidth, or a different supply range, evaluate a modern multiplier family as a new design rather than attempting an automatic board replacement.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto AD534JH AD534JD AD534SH
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Product Function Four-quadrant multiplier-divider Four-quadrant multiplier-divider Four-quadrant multiplier-divider Four-quadrant multiplier-divider

Pangunahing mga Pagkakaiba

  • Integrated four-quadrant precision multiplication (kumpara saDiscrete multiplier networks using separate amplifiers and precision resistors)
  • Laser-trimmed calibration (kumpara saUntrimmed discrete multiplier implementation)
  • Documented low-noise performance (kumpara saGeneral-purpose precision multiplier modules)
  • On-chip buried Zener reference (kumpara saMultiplier circuits using an external precision reference)

Talaan ng Disenyo

Place the AD534JHZ where the multiplier inputs, feedback components, and output trace are electrically short. Keep high-current and switching-node copper away from the input and reference pins because the multiplier can reject ripple only within its frequency-dependent limits. Use a single low-impedance analog ground region for the device and its precision resistors, and avoid routing sensitive signals beneath the TO-100 body unless the PCB stackup and ground arrangement have been evaluated.

Bypass the supply pins close to the device using the capacitance and ESR requirements specified in the manufacturer application guidance. An inadequate local bypass path can add supply noise to the 90 µV rms output-noise specification and may influence the high-gain multiplier stage. Check startup behavior, supply sequencing, and the maximum supply voltage for the exact ordering grade before energizing the circuit.

Do not treat AD534JH, AD534JD, or AD534SH as automatic replacements merely because their base numbers are identical. Confirm package construction, pin assignment, temperature grade, accuracy class, calibration method, and supply range in the ordering information. A suffix change can alter environmental qualification or mechanical construction even when the multiplier architecture remains the same.

Treat the denominator or reference input as a precision signal node because multiplier accuracy depends on the quality of that reference. Use short traces, stable reference components, and clean grounding to limit error and noise. When working with small signals, include the 90 µV rms device noise from 10 Hz to 10 kHz in the system noise budget and apply additional filtering only where it does not compromise the required measurement bandwidth.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The manufacturer product page and data-sheet excerpts do not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status for the exact AD534JHZ ordering option. AEC-Q100 is not applicable to this analog multiplier-divider product type.

Data napatotohanan sa: 2026-11-18 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

AD534JHZ datasheet AD534JHZ pinout AD534JHZ datasheet pdf AD534JHZ equivalent AD534JHZ drop-in replacement AD534JHZ cross reference AD534JHZ price AD534JHZ stock Analog Devices AD534JHZ AD534 4-quadrant multiplier TO-100 AD534JHZ signal scaling AD534JHZ vs AD534JH

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices AD534 AD534JHZ AD534JH AD534JD AD534SH four-quadrant multiplier multiplier-divider analog multiplier analog signal processing analog computation precision calibration laser trimming monolithic construction buried Zener reference 10 V scale factor 90 µV rms output noise 10 Hz to 10 kHz bandwidth TO-100 10-pin TO-100 through-hole package semiconductor IC interface IC RoHS REACH
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ