AD548BQ - Low-Power Precision BiFET Op Amp | Analog Devices
MPN: AD548BQ ✗ Tapus ng BuhayAD548BQ Ulas
A BiFET operational amplifier is a voltage-input amplifier whose input stage uses field-effect transistors. This amplifier category combines very low input bias current with low supply consumption, making it suitable for precision measurement, buffering, and feedback circuits in which source impedance or sensor leakage could otherwise create measurement error. Within the broader hierarchy, the AD548BQ is an operational amplifier, analog IC, and semiconductor.
The AD548 family uses ion-implanted FET technology and laser wafer trimming. Its principal characteristics include an 800 uV maximum input offset voltage, 1 MHz gain-bandwidth product, 10 pA maximum input bias current after warm-up, and 200 uA maximum quiescent current. The Analog Devices product page identifies AD548B as an industrial-temperature product and describes low drift, low supply current, and strong direct-current and alternating-current performance.
The AD548BQ operates as a general-purpose precision amplifier with one amplifier circuit. Its low bias current reduces errors when driving high source impedances, while its low quiescent current supports compact, low-power instrumentation. The hermetically sealed ceramic package is useful where environmental robustness and long-term operating stability are important, although component availability should be confirmed before starting a new design because Analog Devices marks the AD548 family as not recommended for new designs.
Typical uses include precision buffer stages, low-level sensor interfaces, laboratory instrumentation, photodiode signal conditioning, and feedback networks requiring low input leakage. The 1 MHz bandwidth is suitable for moderate-frequency signal paths rather than high-speed waveform processing. In each case, the input network, output loading, and supply bypass arrangement determine whether the amplifier's offset and noise behavior can be fully utilized.
Designers should begin with the manufacturer datasheet pin-description table, then verify the ceramic package orientation and pin numbering before PCB assembly. Adequate supply bypassing and careful routing of high-impedance input nodes are especially important because parasitic capacitance and leakage can degrade accuracy even when the amplifier itself is operating within specification.
This page consolidates the manufacturer's AD548 family information, identifies the hermetically sealed AD548BQ configuration, documents the limits of current sourcing, and provides comparison and application guidance for engineers who must decide whether this legacy precision amplifier remains suitable for an existing or long-lived instrument.
Mga alternatibo na pwedeng ilagay na AD548BQ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok AD548BQ (parehas na form factor at footprint) — pagkakaiba sa Input Bias Current, Package, Quiescent Current.
AD548AQ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD548BR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD548KNZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD548BQ Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Single precision operational amplifier |
| Number of Circuits | 1 circuit |
| Input Offset Voltage | 800 uV maximum |
| Gain-Bandwidth Product | 1 MHz |
| Input Bias Current | 10 pA maximum, warmed up |
| Kuru-kuryente ng Kapayapaan | 200 uA maximum |
| Technology | Ion-implanted FET with laser wafer trimming |
| Hanay ng Temperature na Operasyon | -40C to +85C for AD548B |
| Packhaging | 8-CERDIP, hermetically sealed |
| Package Dimensions | 0.300 in / 7.62 mm package width |
| Uri ng Pagpapasok | Through-hole |
Pin Configuration ng AD548BQ
| Pin 1 | NC — Not connected |
| Pin 2 | -IN — Inverting input |
| Pin 3 | +IN — Noninverting input |
| Pin 4 | V- — Negative supply |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Output |
| Pin 7 | V+ — Positive supply |
| Pin 8 | NC — Not connected |
Tipikal na mga Gamit
AD548BQ ay nararapat para sa 6 aplikasyons: Precision Sensor Buffering, Low-Power Measurement Instrumentation, Photodiode Signal Conditioning, Laboratory Buffer Stage, Process-Control Signal Conditioning, Legacy Equipment Repair.
Precision Sensor Buffering
The AD548BQ is appropriate for buffering sensors whose output impedance is high enough that input bias current could otherwise create a measurement error. Its 10 pA maximum warmed-up input bias current helps preserve the sensor's voltage, while the 1 MHz gain-bandwidth product provides useful bandwidth for moderate-rate signals. The 800 uV maximum offset specification must be included in the measurement-uncertainty budget. Because this is an amplifier rather than a dedicated instrumentation amplifier, input bias-current cancellation and drift may still require calibration. Keep sensitive input traces short, shield them from contamination, and verify the complete offset, noise, and drift chain rather than relying on input bias current alone.
Inirekomenda
Low-Power Measurement Instrumentation
The AD548BQ suits portable or benchtop measurement equipment in which every milliampere affects battery life, heat, or available supply headroom. Its 200 uA maximum quiescent current is substantially lower than that of many general-purpose precision amplifiers, while the 1 MHz bandwidth supports slowly varying and moderately fast measurement channels. The designer should calculate the amplifier's operating dissipation from the actual supply voltage and load, then confirm that the output swing and input common-mode range cover the complete measurement range. For long acquisition periods, verify offset and drift specifications over the intended temperature interval because low power alone does not guarantee long-term measurement stability.
Inirekomenda
Photodiode Signal Conditioning
The AD548BQ can form the first amplification stage for a photodiode or other current-producing sensor because its low warmed-up input bias current limits the error introduced at the input node. The 1 MHz gain-bandwidth product is sufficient for many photodiode monitoring, position, and optical-communication interfaces, although higher-bandwidth optical systems may require a faster amplifier. Care must be taken with reverse-bias stability, input capacitance, noise gain, and feedback compensation because these parameters can produce oscillation or reduce phase margin. Use the manufacturer's recommended feedback topology and keep the photodiode connection short, with guarded grounding around the high-impedance input.
Inirekomenda
Laboratory Buffer Stage
In laboratory instrumentation, the AD548BQ can buffer a source before a measurement or conversion stage while preserving high input impedance and drawing little quiescent current. Its 800 uV maximum offset voltage should be considered when the source voltage is small, and its 1 MHz bandwidth should be checked against the required settling time. For precision DC measurements, the input offset voltage, input bias current, drift, and noise must all be included in the uncertainty calculation. Stable layout, clean power bypassing, and low-leakage PCB surfaces are important because a high-impedance amplifier can reveal contamination or condensation that would have little effect on a conventional low-impedance signal path.
Inirekomenda
Process-Control Signal Conditioning
The AD548BQ can amplify weak feedback or sensing signals in industrial process-control circuitry when the operating environment remains within the AD548B family's -40C to +85C industrial range. Low quiescent current reduces the heat generated inside compact control equipment, and the 1 MHz bandwidth can handle many slow closed-loop control signals. The hermetically sealed 8-CERDIP construction is of interest for long-lived laboratory or industrial equipment, although the manufacturer identifies the AD548 family as not recommended for new designs. Verify surge, electromagnetic-interference, grounding, and isolation requirements at the system level; the amplifier's operating range alone does not establish compliance for a finished industrial installation.
Inirekomenda
Legacy Equipment Repair
AD548BQ is well suited to maintaining a proven laboratory, medical, or industrial instrument that already uses the hermetically sealed 8-CERDIP AD548BQ footprint. Preserving the original architecture avoids the leakage, noise, offset, and qualification changes that can accompany a redesign. The 10 pA maximum warmed-up input bias current and 200 uA maximum quiescent current reproduce the core low-power characteristics expected from the AD548 family. Before fitting a replacement, compare the exact suffix, pinout, ceramic-package dimensions, temperature grade, and electrical characteristics with the failed device. Also inspect the surrounding circuit for damaged insulation, contamination, or capacitor leakage that could imitate an amplifier failure.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for AD548BQ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | AD548AQ | AD548BR | AD548KNZ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-CERDIP, hermetically sealed | 8-CERDIP candidate; verify exact construction | 8-CERDIP candidate; verify exact construction | DIP construction; verify ceramic-body compatibility |
| Amplifier Configuration | Single operational amplifier | Single AD548-family operational amplifier | Single AD548-family operational amplifier | Single operational amplifier |
| Special Features | Precision, low-power BiFET operational amplifier | AD548-family precision, low-power BiFET amplifier | AD548-family precision, low-power BiFET amplifier | Low-power precision monolithic operational amplifier |
Pangunahing mga Pagkakaiba
- Very low input bias current supports leakage-sensitive measurement (kumpara saAD548KNZ)
- Low quiescent current supports compact low-power designs (kumpara saAD548AQ)
- Hermetically sealed ceramic package supports legacy robust installations (kumpara saAD548BR)
Talaan ng Disenyo
Treat the noninverting and inverting inputs as high-impedance nodes. Route them away from switching nodes, power-supply traces, relay contacts, and exposed connector fields. Use a protective guard structure around sensitive input routing where board contamination could create leakage. Keep the feedback components close to pins 2, 3, and 6, and verify the physical orientation of the ceramic package against the manufacturer package drawing before assembly.
Place the supply-bypass capacitor close to pins 7 and 4 and follow the manufacturer layout guidance for the ceramic package. Confirm the actual supply voltage, common-mode range, and output swing before selecting feedback resistors. Because the AD548BQ is specified for low quiescent current, any added bias network can consume as much current as the amplifier and should be included in the complete power-budget calculation.
Check stability with the actual source capacitance, load, and feedback network. The 1 MHz gain-bandwidth product is sufficient for many precision and instrumentation signals, but high noise gain combined with stray capacitance can reduce phase margin. Evaluate gain-bandwidth behavior and settling at the lowest noise gain used in the design, and follow the recommended compensation approach when driving capacitive loads.
Do not assume that every AD548 suffix is mechanically interchangeable with the 8-CERDIP AD548BQ. A functional match requires identical pin assignment, ceramic-body dimensions, temperature grade, electrical limits, and qualification status. For repair work, inspect the board and socket for contamination, damaged insulation, and socket stress before replacing the amplifier; otherwise an apparent amplifier failure may recur.
Impormasyon ng Pagsunod sa Kautusan
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is identified for AD548BQ in the manufacturer product information. The AD548 family is marked not recommended for new designs by Analog Devices.