AD7492BRZ - 12-Bit 1 MSPS SAR ADC | Analog Devices
MPN: AD7492BRZ ✓ NakahandaAD7492BRZ Ulas
A successive-approximation ADC, or SAR ADC, repeatedly compares the analog input with a generated reference voltage and adjusts a binary-weighted internal DAC until the comparator output changes state. This architecture combines predictable conversion latency with low power consumption and moderate resolution. The AD7492 belongs to the ADC hierarchy of data-converter ICs, providing a practical bridge between a continuously varying sensor signal and a digital value produced by a microcontroller, DSP, or programmable logic controller.
The AD7492BRZ provides a 12-bit conversion result, one analog input channel, an internal reference and clock, and a low-power operating mode. According to the manufacturer product information, the AD7492 family includes AD7492, AD7492-4, and AD7492-5 variants with maximum throughput rates of 1 MSPS, 400 kSPS, and 1.25 MSPS respectively. The target AD7492 variant therefore balances conversion speed against power consumption while retaining a 12-bit output resolution.
The device uses a conversion-controlled SAR architecture without pipeline delay. The BUSY indication rises at the start of conversion and falls 880 ns later for the AD7492 and AD7492-4 variants to signal completion. This deterministic behavior supports software-controlled acquisition, but it also means the host processor must observe conversion timing or use the BUSY signal when transferring each 12-bit result. The internal reference and clock reduce external component count in compact instrumentation designs.
Typical uses include industrial process monitoring, temperature and pressure sensor acquisition, battery-powered measurement instruments, motor and power-system monitoring, laboratory data acquisition, and embedded control systems. The 24-lead SOIC package provides a conventional surface-mount option, while the 2.7 V to 5.25 V operating supply supports both 3.3 V and 5 V systems. The industrial-grade temperature range extends from -40 °C to 85 °C.
Designers should treat the analog input as a high-impedance sampling node and use the pin-description and application-circuit guidance in the manufacturer datasheet when assigning traces and external components. Reference and supply bypassing must follow the recommended values and placement, because settling time at the input directly affects conversion accuracy. Digital output timing should also be checked against the host interface requirements before fixing the acquisition rate.
This page combines the AD7492 family specifications, package information, commercial sourcing details, and engineering guidance with a focus on practical selection. It also distinguishes the standard AD7492 from its lower-speed and higher-speed family variants, helping designers choose the correct member without confusing throughput differences with pin compatibility.
Mga alternatibo na pwedeng ilagay na AD7492BRZ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok AD7492BRZ (parehas na form factor at footprint) — pagkakaiba sa Package.
AD7492BRZ-5
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD7492-4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD7492-5
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD7492BRZ Mga Pinakamataas na Rating at Electrical Characteristics
| Pangangasiwaan | 12 bit |
| Architecture | Successive approximation (SAR) |
| Input Channels | 1 analog input |
| Maximum Throughput, AD7492 | 1 MSPS |
| Maximum Throughput, AD7492-5 | 1.25 MSPS |
| Maximum Throughput, AD7492-4 | 400 kSPS |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Hanay ng Voltage ng Input | 0 V to 2.5 V |
| Typical Power Consumption | 4 mW at 1 MSPS |
| Reference | Internal reference |
| Clock | Internal clock |
| Conversion Complete Timing | BUSY deasserts 880 ns after conversion start for AD7492 and AD7492-4 |
| Pipeline Delay | 0 cycles (no pipeline delay) |
| Packhaging | 24-lead SOIC, MS-013AD |
| Bilang ng Pin | 24 pins |
| Uri ng Pagpapasok | Surface mount |
| Temperature na Operasyon | -40 °C to 85 °C |
| Screening Level | Industrial |
Gabay sa Pin Configuration ng AD7492BRZ 24-lead soic, ms-013ad
Pin configuration para sa AD7492BRZ (24-lead soic, ms-013ad package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa AD7492BRZ.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
AD7492BRZ ay nararapat para sa 6 aplikasyons: Industrial Process Monitoring, Temperature and Pressure Sensor Acquisition, Battery-Powered Measurement Instruments, Motor and Power-System Monitoring, Laboratory and Data-Acquisition Systems, Embedded Control and Sensor Interfaces.
Industrial Process Monitoring
The AD7492BRZ suits industrial process-monitoring channels that must digitize a restricted analog input range at moderate speed. Its 12-bit resolution provides 4096 discrete codes, while the 0 V to 2.5 V input range suits conditioned outputs from current-to-voltage converters, resistive bridges, and industrial sensor transmitters. The 1 MSPS rate also provides more headroom than many process signals require, allowing the system to sample multiple conditioning channels sequentially when the host controls multiplexing. Operation from a single 2.7 V to 5.25 V supply simplifies field-instrument power architecture, and the -40 °C to 85 °C industrial range supports controlled cabinets and production equipment. Place the analog trace away from digital outputs and follow the manufacturer’s recommended bypass and reference layout to preserve accuracy.
Inirekomenda
Temperature and Pressure Sensor Acquisition
The AD7492BRZ is appropriate for digitizing conditioned outputs from RTDs, thermocouple amplifiers, pressure transmitters, and digital temperature sensors exposed through analog interfaces. A 12-bit converter provides sufficient resolution for many slow-changing industrial measurements, while the 1 MSPS capability allows the acquisition system to oversample relative to the sensor’s thermal settling time. The internal reference and clock reduce the external support circuitry needed in a compact measurement module. Because sensor excitation and bridge currents can inject noise through shared ground paths, route the AD7492BRZ analog input and reference connections away from switching nodes and digital output edges. Use the manufacturer application guidance for input-source impedance, acquisition timing, and bypass placement.
Battery-Powered Measurement Instruments
The AD7492BRZ fits portable and battery-powered measurement equipment where a 12-bit measurement channel must consume little power and board area. Typical power consumption is approximately 4 mW at 1 MSPS, while the 24-lead SOIC package can be placed on a compact mixed-signal board. The 2.7 V lower supply limit supports systems operated from a single Li-ion cell with a low-voltage regulator, and the 5.25 V upper limit accommodates 5 V industrial rails. In portable designs, the internal reference and clock are valuable because they reduce component count, but their use does not remove the need for careful analog grounding. Trigger conversions only when useful samples are required and disable unused outputs where the selected architecture permits it to reduce switching activity.
Motor and Power-System Monitoring
The AD7492BRZ can serve as the ADC in current, voltage, or position-feedback subsystems for motors and power converters when the sensed signal is conditioned into the 0 V to 2.5 V input range. The 1 MSPS rate is well matched to many supervisory loops that monitor current magnitude, DC-link conditions, or mechanical position without requiring a high-resolution waveform capture. The non-pipelined SAR conversion provides a defined completion event through the BUSY signal, allowing a controller to coordinate conversion with PWM updates and fault handling. Keep the analog front end close to the converter and avoid routing shunt or power-stage signals beneath the SOIC. Validate timing against the switching node because the ADC timing specification does not replace the system’s analog settling requirements.
Inirekomenda
Laboratory and Data-Acquisition Systems
The AD7492BRZ is appropriate for compact laboratory and field data-acquisition modules that need a deterministic 12-bit SAR channel rather than a continuous-output pipeline ADC. The 1 MSPS conversion rate can capture events at a useful sampling rate, while the internal reference and clock simplify module-level synchronization. Because the device has no pipeline delay, the controller can issue a conversion and wait for BUSY before reading the parallel result. For instrumentation requiring multiple inputs, the single analog channel means multiplexing or an external analog switch is needed, and each switched source must be allowed to settle before conversion. Use the official AD7492 datasheet for the electrical interface, digital timing, and input-conditioning requirements.
Embedded Control and Sensor Interfaces
The AD7492BRZ can connect a conditioned analog sensor to a microcontroller, DSP, or programmable logic controller that requires a 12-bit digital measurement. Its 1 MSPS rate is more than adequate for many thermal, level, pressure, and position sensors, while the internal clock and reference support a self-contained acquisition channel. The deterministic BUSY indication simplifies firmware sequencing because no pipeline-stage tracking is required. Interface the digital outputs according to the host’s voltage levels and ensure the acquisition interval leaves sufficient time for analog settling. For battery-operated devices, operate the ADC and controller from a common low-noise rail where practical, and test the complete signal chain because reference noise, source impedance, and layout can determine the usable resolution more than the nominal bit count.
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for AD7492BRZ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | AD7492BRZ-5 | AD7492-4 | AD7492-5 |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-lead SOIC, MS-013AD | 24-lead SOIC, MS-013AD | 24-lead SOIC, MS-013AD | 24-lead SOIC, MS-013AD |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Throughput | 1 MSPS | 1.25 MSPS | 400 kSPS | 1.25 MSPS |
| Architecture | 12-bit SAR ADC | 12-bit SAR ADC | 12-bit SAR ADC | 12-bit SAR ADC |
| Input Channels | 1 | 1 | 1 | 1 |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Input Voltage Range | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V |
| BUSY Completion Timing | 880 ns after conversion start | 680 ns after conversion start | 880 ns after conversion start | 680 ns after conversion start |
Pangunahing mga Pagkakaiba
- Balanced conversion speed and power in the standard family member (kumpara saAD7492-4)
- Higher throughput is available without changing resolution (kumpara saAD7492BRZ-5)
- Complete integrated conversion support for compact designs (kumpara saAD7492-4)
Talaan ng Disenyo
Treat the analog input, reference, and supply paths as one compact signal-conditioning group on the PCB. Follow the manufacturer application circuit for input-source impedance, filtering, and bypass capacitors, and place the recommended capacitors directly beside their associated pins. Keep the analog trace short and away from the digital output bus, clock edge, and any switching-node copper. A clean reference return is as important as a short input trace because reference disturbance can appear directly in the conversion result.
The standard AD7492 uses a deterministic, non-pipelined conversion sequence, so software and hardware should wait for BUSY to be deasserted before reading the output data. The BUSY interval is 880 ns for the AD7492, while the -5 variant deasserts BUSY after 680 ns. If the host operates from a different clock domain, synchronize control and output signals appropriately and test setup and hold timing against the host device rather than assuming that nominal processor timing is sufficient.
Budget approximately 4 mW for the AD7492 at 1 MSPS and design the supply for both analog and digital requirements. Place local decoupling at the supply pins with the values and layout specified by Analog Devices, and route the return current directly to the appropriate ground pins. Because the family supports 2.7 V to 5.25 V operation, confirm that the selected voltage preserves the required input range, output logic levels, reference behavior, and timing margin across the complete operating temperature range.
Impormasyon ng Pagsunod sa Kautusan
The AD7492BRZ is an industrial-screened 24-lead SOIC component. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not established for the exact ordering code and are therefore left unknown.