AD9830AST - 10-Bit, 50 MHz Direct Digital Synthesizer | Analog Devices
MPN: AD9830AST ✗ Tapus ng BuhayAD9830AST Ulas
A direct digital synthesizer is a waveform-generation IC whose output frequency and phase are determined by digital control words. Within the broader hierarchy of signal-generation ICs, a DDS combines a phase accumulator, waveform memory, and DAC to produce a digitally controlled output. This architecture supports precise frequency programming and direct digital control without requiring a conventional analog voltage-controlled oscillator.
The AD9830AST uses a 32-bit frequency tuning word and a 10-bit DAC. Its clock input can operate up to 50 MHz, allowing the generated frequency and phase behavior to be set through the serial interface. Frequency modulation and phase modulation expand the usefulness of the device in swept-signal, waveform-generation, communications, and instrumentation systems. The manufacturer describes the core implementation as a numerically controlled oscillator using a phase accumulator, sine look-up table, and 10-bit DAC on one CMOS chip.
The 48-lead TQFP package provides separate control, clock, synchronization, and analog-output connections needed for a complete DDS implementation. Because the output is generated digitally, the architecture simplifies repeatable frequency programming and enables compact waveform sources for test equipment and embedded signal-generation functions. Clock jitter, reference accuracy, reconstruction-filter design, and power-supply noise remain important system-level considerations.
Typical uses include sinusoidal excitation for sensor testing, local-oscillator generation in communications equipment, audio and ultrasonic test signals, and programmable waveform generation. The serial control interface allows a host processor or microcontroller to update the frequency and phase words while the synthesizer operates. Its 50 MHz maximum clock rate should be considered when determining achievable output frequency and spectral performance.
For reliable implementation, use a clean reference clock, route the serial interface away from sensitive output paths, decouple the supply pins locally, and include an appropriate reconstruction filter after the DAC output. When comparing this part with alternatives, verify the full pinout, supply requirements, interface timing, output architecture, and package rather than relying only on the 50 MHz clock rating.
This page organizes the AD9830AST specifications, drop-in relationship, sourcing path, and practical design considerations into one engineering-focused reference. It also identifies which parameters require confirmation from the manufacturer datasheet, helping designers move from component selection to PCB implementation with fewer specification gaps.
Mga alternatibo na pwedeng ilagay na AD9830AST — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
AD9830ASTZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD9830AST Mga Spesipikasyon
| Device Type | Direct digital synthesizer (DDS) |
| Architecture | Numerically controlled oscillator with phase accumulator, sine look-up table, and DAC |
| Maksimum na Taktiko ng Oras | 50 MHz |
| Frequency Tuning Word Width | 32 bit |
| DAC Resolution | 10 bit |
| Output Waveform | Sine wave |
| Frequency Modulation | Supported |
| Phase Modulation | Supported |
| Process Technology | CMOS |
| Integrated Converters | 1 DAC |
| Packhaging | 48-lead TQFP, 7 x 7 mm |
| Uri ng Pagpapasok | Surface mount |
| Bilang ng Pin | 48 pins |
Gabay sa Pin Configuration ng AD9830AST 48-lead tqfp, 7 x 7 mm
Pin configuration para sa AD9830AST (48-lead tqfp, 7 x 7 mm package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa AD9830AST.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
AD9830AST ay nararapat para sa 6 aplikasyons: Communications Local Oscillator, Precision Sensor Test Excitation, Programmable Audio and Ultrasonic Signal Source, Embedded Waveform Generator, Portable Diagnostic Device, Laboratory and Production Calibration.
Communications Local Oscillator
The AD9830AST can generate a digitally controlled local-oscillator signal for communications equipment because it combines a 32-bit frequency tuning word with a 50 MHz maximum clock and dedicated frequency- and phase-modulation functions. The synthesizer is placed between the system reference clock and the RF signal path, with its serial control word updated by the host processor. This allows compact frequency changes without relying on a manually tuned analog oscillator. In a practical RF design, the DDS output must pass through filtering, gain control, and frequency translation stages, while reference-clock jitter and DDS phase noise must be included in the link-budget analysis. The 10-bit DAC is suitable for creating a configurable intermediate frequency or low-level excitation waveform.
Inirekomenda
Precision Sensor Test Excitation
The AD9830AST is appropriate for generating calibrated sine-wave excitation in sensor and instrumentation systems. Its 32-bit tuning word provides fine frequency adjustment, while the internal 10-bit DAC converts the programmed phase sequence into an analog test signal. A microcontroller can update the frequency and phase registers to sweep a sensor across a controlled stimulus range. The analog output should normally pass through a reconstruction filter, attenuation or gain control, and output buffering before being applied to the device under test. Designers should characterize clock accuracy, output amplitude, DAC distortion, and filter response across the intended test band because those parameters determine the overall excitation quality.
Inirekomenda
Programmable Audio and Ultrasonic Signal Source
The AD9830AST can serve as the programmable waveform core of an audio or ultrasonic signal source when a compact, digitally controlled sine output is required. The 50 MHz maximum clock supports multiple output-frequency relationships through the 32-bit tuning word, while phase modulation permits controlled timing changes. In an ultrasonic driver, the DDS output should be followed by a reconstruction filter, suitable amplification, and protection appropriate to the transducer’s voltage and current requirements. In audio test systems, external filtering and gain control can shape the level and bandwidth. The 10-bit DAC resolution is appropriate for many stimulus-generation tasks, but harmonic and spurious-content requirements should be checked against the complete analog signal chain.
Inirekomenda
Embedded Waveform Generator
The AD9830AST integrates the phase accumulator, sine look-up table, and 10-bit DAC required for a compact embedded waveform generator. It can replace a larger collection of discrete timing, memory, and conversion circuitry when a controlled sine source is needed near the system logic. A microcontroller writes the 32-bit frequency and phase data over the serial interface, while synchronization signals coordinate updates with other acquisition or actuation functions. The DDS output is normally passed through a reconstruction filter and buffer before external use. This arrangement is particularly useful in automated test fixtures where frequency must be reprogrammed frequently and accurate repeatability is more important than a large number of waveform shapes.
Inirekomenda
Portable Diagnostic Device
The AD9830AST can support portable diagnostic and service equipment that needs a compact programmable excitation source without a separate bench waveform generator. Its serial control interface permits a low-power microcontroller to adjust output frequency and phase, and the 48-lead TQFP package supports integration into a densely populated instrument. The generated waveform can stimulate transducers, motors, or analog sensor networks while the host records the response. Because the device produces a 10-bit DAC waveform, output filtering, buffering, and level calibration are important for portable equipment where battery noise and load-dependent impedance changes may affect accuracy. A controlled reference clock also helps maintain repeatable measurements.
Inirekomenda
Laboratory and Production Calibration
The AD9830AST is suitable for laboratory and production calibration systems requiring repeatable sinusoidal excitation with digitally selected frequency. The 32-bit tuning word allows the controller to define the stimulus precisely, while the sine look-up table and 10-bit DAC create a compact output stage. In a calibration fixture, the DDS can drive a reference sensor or stimulate a production assembly, while an ADC captures the response for comparison against limits. Synchronization pins and the serial programming interface simplify deterministic sequencing. For production accuracy, validate reference-clock tolerance, DAC linearity, output-noise spectrum, reconstruction-filter response, and load regulation because the IC alone does not define the accuracy of the complete calibration path.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for AD9830AST — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | AD9830ASTZ |
|---|---|---|
| Package | 48-lead TQFP, 7 x 7 mm | 48-lead TQFP, 7 x 7 mm |
| Brand | Analog Devices | Analog Devices |
| Device Type | Direct digital synthesizer | Direct digital synthesizer |
| DAC Resolution | 10 bit | 10 bit |
| Maximum Clock Frequency | 50 MHz | 50 MHz |
| Frequency Tuning Word | 32 bit | 32 bit |
| Modulation Capability | Frequency modulation and phase modulation | Frequency modulation and phase modulation |
| Output Waveform | Sine wave | Sine wave |
Pangunahing mga Pagkakaiba
- Compact integration of the complete DDS signal path (kumpara saAD9830ASTZ)
- Fine digital frequency programming (kumpara saAD9830ASTZ)
- Dedicated modulation functions (kumpara saAD9830ASTZ)
Talaan ng Disenyo
Route the reference clock and serial control signals away from the analog output and reconstruction-filter network to reduce coupling into the sine-wave signal. Follow the manufacturer’s recommended component placement for the supply, ground, clock, and DAC output pins. Ground-plane distribution should support the required return paths without placing high-current digital return currents beneath sensitive analog output nodes.
The DDS output contains images and harmonics associated with the 10-bit DAC and phase-accumulator architecture. Use a reconstruction filter selected for the required output band, and verify its cutoff, attenuation, and phase response across the operating range. Evaluate the filter against the 50 MHz maximum clock because a clock-related image may appear close to the desired output frequency.
Decouple the supply pins locally using the capacitor configuration shown in the manufacturer’s application circuit, and provide a low-impedance connection from each ground pin to the circuit ground plane. A clean reference clock is essential because clock phase noise can degrade DDS spectral performance. Measure output noise and spur levels with the final regulator, clock source, layout, and enclosure in place.
Do not infer pin compatibility from the package outline alone. Confirm every AD9830AST terminal against the manufacturer pin-description table, including supply, ground, clock, synchronization, serial-control, and analog-output functions. When considering AD9830ASTZ as a replacement, also verify ordering details, temperature grade, lead finish, and lifecycle requirements before committing the part to production.
Impormasyon ng Pagsunod sa Kautusan
The AD9830AST is listed as obsolete. Compliance attributes are not stated in the available manufacturer and distributor information and therefore remain unknown.