Analog Devices

AD9830AST - 10-Bit, 50 MHz Direct Digital Synthesizer | Analog Devices

N.º da peça: AD9830AST ✗ Fim de vida
48-lead TQFP, 7 x 7 mm Package 50 MHz Speed
MOQ: 1 |

AD9830AST Visão geral

The Analog Devices AD9830AST is a direct digital synthesizer, or DDS, with a 10-bit internal DAC, 50 MHz maximum clock frequency, and 32-bit tuning word in a 48-lead TQFP package measuring 7 x 7 mm. It generates a digitally controlled sine-wave output from a phase accumulator and sine look-up table, with phase-modulation and frequency-modulation capability.

A direct digital synthesizer is a waveform-generation IC whose output frequency and phase are determined by digital control words. Within the broader hierarchy of signal-generation ICs, a DDS combines a phase accumulator, waveform memory, and DAC to produce a digitally controlled output. This architecture supports precise frequency programming and direct digital control without requiring a conventional analog voltage-controlled oscillator.

The AD9830AST uses a 32-bit frequency tuning word and a 10-bit DAC. Its clock input can operate up to 50 MHz, allowing the generated frequency and phase behavior to be set through the serial interface. Frequency modulation and phase modulation expand the usefulness of the device in swept-signal, waveform-generation, communications, and instrumentation systems. The manufacturer describes the core implementation as a numerically controlled oscillator using a phase accumulator, sine look-up table, and 10-bit DAC on one CMOS chip.

The 48-lead TQFP package provides separate control, clock, synchronization, and analog-output connections needed for a complete DDS implementation. Because the output is generated digitally, the architecture simplifies repeatable frequency programming and enables compact waveform sources for test equipment and embedded signal-generation functions. Clock jitter, reference accuracy, reconstruction-filter design, and power-supply noise remain important system-level considerations.

Typical uses include sinusoidal excitation for sensor testing, local-oscillator generation in communications equipment, audio and ultrasonic test signals, and programmable waveform generation. The serial control interface allows a host processor or microcontroller to update the frequency and phase words while the synthesizer operates. Its 50 MHz maximum clock rate should be considered when determining achievable output frequency and spectral performance.

For reliable implementation, use a clean reference clock, route the serial interface away from sensitive output paths, decouple the supply pins locally, and include an appropriate reconstruction filter after the DAC output. When comparing this part with alternatives, verify the full pinout, supply requirements, interface timing, output architecture, and package rather than relying only on the 50 MHz clock rating.

This page organizes the AD9830AST specifications, drop-in relationship, sourcing path, and practical design considerations into one engineering-focused reference. It also identifies which parameters require confirmation from the manufacturer datasheet, helping designers move from component selection to PCB implementation with fewer specification gaps.

Alternativas drop-in para AD9830AST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

AD9830ASTZ

✅ Drop-In
📦 48-lead TQFP, 7 x 7 mm
Same 10-bit DDS, 50 MHz maximum clock, 32-bit tuning word, 48-pin package, and documented pin-compatible terminal arrangement; ordering and finish details must be confirmed

📋 Alternativa de referência (fora do catálogo)

AD9830AST Especificações

Device Type Direct digital synthesizer (DDS)
Architecture Numerically controlled oscillator with phase accumulator, sine look-up table, and DAC
Frequência máxima de clock 50 MHz
Frequency Tuning Word Width 32 bit
DAC Resolution 10 bit
Output Waveform Sine wave
Frequency Modulation Supported
Phase Modulation Supported
Process Technology CMOS
Integrated Converters 1 DAC
Encapsulamento 48-lead TQFP, 7 x 7 mm
Tipo de montagem Surface mount
Contagem de pinos 48 pins

Guia de Configuração de Pinos do AD9830AST 48-lead tqfp, 7 x 7 mm

Configuração de pinos para AD9830AST (pacote 48-lead tqfp, 7 x 7 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 48-lead tqfp, 7 x 7 mm para AD9830AST

Nenhum dado detalhado de pinagem disponível para AD9830AST.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

AD9830AST é adequado para 6 aplicaçãos: Communications Local Oscillator, Precision Sensor Test Excitation, Programmable Audio and Ultrasonic Signal Source, Embedded Waveform Generator, Portable Diagnostic Device, Laboratory and Production Calibration.

🌐

Communications Local Oscillator

The AD9830AST can generate a digitally controlled local-oscillator signal for communications equipment because it combines a 32-bit frequency tuning word with a 50 MHz maximum clock and dedicated frequency- and phase-modulation functions. The synthesizer is placed between the system reference clock and the RF signal path, with its serial control word updated by the host processor. This allows compact frequency changes without relying on a manually tuned analog oscillator. In a practical RF design, the DDS output must pass through filtering, gain control, and frequency translation stages, while reference-clock jitter and DDS phase noise must be included in the link-budget analysis. The 10-bit DAC is suitable for creating a configurable intermediate frequency or low-level excitation waveform.

🏭

Precision Sensor Test Excitation

The AD9830AST is appropriate for generating calibrated sine-wave excitation in sensor and instrumentation systems. Its 32-bit tuning word provides fine frequency adjustment, while the internal 10-bit DAC converts the programmed phase sequence into an analog test signal. A microcontroller can update the frequency and phase registers to sweep a sensor across a controlled stimulus range. The analog output should normally pass through a reconstruction filter, attenuation or gain control, and output buffering before being applied to the device under test. Designers should characterize clock accuracy, output amplitude, DAC distortion, and filter response across the intended test band because those parameters determine the overall excitation quality.

🔊

Programmable Audio and Ultrasonic Signal Source

The AD9830AST can serve as the programmable waveform core of an audio or ultrasonic signal source when a compact, digitally controlled sine output is required. The 50 MHz maximum clock supports multiple output-frequency relationships through the 32-bit tuning word, while phase modulation permits controlled timing changes. In an ultrasonic driver, the DDS output should be followed by a reconstruction filter, suitable amplification, and protection appropriate to the transducer’s voltage and current requirements. In audio test systems, external filtering and gain control can shape the level and bandwidth. The 10-bit DAC resolution is appropriate for many stimulus-generation tasks, but harmonic and spurious-content requirements should be checked against the complete analog signal chain.

🧩

Embedded Waveform Generator

The AD9830AST integrates the phase accumulator, sine look-up table, and 10-bit DAC required for a compact embedded waveform generator. It can replace a larger collection of discrete timing, memory, and conversion circuitry when a controlled sine source is needed near the system logic. A microcontroller writes the 32-bit frequency and phase data over the serial interface, while synchronization signals coordinate updates with other acquisition or actuation functions. The DDS output is normally passed through a reconstruction filter and buffer before external use. This arrangement is particularly useful in automated test fixtures where frequency must be reprogrammed frequently and accurate repeatability is more important than a large number of waveform shapes.

💊

Portable Diagnostic Device

The AD9830AST can support portable diagnostic and service equipment that needs a compact programmable excitation source without a separate bench waveform generator. Its serial control interface permits a low-power microcontroller to adjust output frequency and phase, and the 48-lead TQFP package supports integration into a densely populated instrument. The generated waveform can stimulate transducers, motors, or analog sensor networks while the host records the response. Because the device produces a 10-bit DAC waveform, output filtering, buffering, and level calibration are important for portable equipment where battery noise and load-dependent impedance changes may affect accuracy. A controlled reference clock also helps maintain repeatable measurements.

🖥️

Laboratory and Production Calibration

The AD9830AST is suitable for laboratory and production calibration systems requiring repeatable sinusoidal excitation with digitally selected frequency. The 32-bit tuning word allows the controller to define the stimulus precisely, while the sine look-up table and 10-bit DAC create a compact output stage. In a calibration fixture, the DDS can drive a reference sensor or stimulate a production assembly, while an ADC captures the response for comparison against limits. Synchronization pins and the serial programming interface simplify deterministic sequencing. For production accuracy, validate reference-clock tolerance, DAC linearity, output-noise spectrum, reconstruction-filter response, and load regulation because the IC alone does not define the accuracy of the complete calibration path.

What is the AD9830AST?
The AD9830AST is a 10-bit, direct digital synthesizer capable of using a 50 MHz clock in a 48-lead TQFP package. Analog Devices describes the device as a numerically controlled oscillator combining a phase accumulator, sine look-up table, and 10-bit DAC on one CMOS chip. Its 32-bit tuning word controls the synthesized output, while dedicated modulation support allows frequency or phase adjustment.
What are the key specifications of AD9830AST that engineers should know?
The main AD9830AST specifications are a 50 MHz maximum clock frequency, a 32-bit frequency tuning word, a 10-bit internal DAC, sine-wave generation, frequency modulation, and phase modulation. The device is offered in a 48-lead, 7 x 7 mm TQFP package. According to the Analog Devices AD9830 product page and datasheet, these features make the IC suitable for digitally programmed waveform and local-oscillator generation.
What is the difference between AD9830AST and AD9830ASTZ?
AD9830ASTZ is a closely related AD9830 orderable variant with the same 10-bit DDS architecture, 50 MHz clock capability, 32-bit tuning word, and 48-pin 7 x 7 mm package. Cross-reference information describes the two as having consistent terminals, packages, and principal performance characteristics. Confirm the exact ordering code, temperature grade, lead-finish requirements, and availability before substituting one for the other.
When should I choose AD9830AST over another direct digital synthesizer?
Choose the AD9830AST when the design requires a compact 10-bit sine-wave DDS with a 32-bit tuning word and operation from a clock signal up to 50 MHz. It is especially suitable for instrumentation, communications, and embedded waveform generation where frequency and phase must be programmed digitally. Select an alternative only after confirming pin compatibility, interface timing, supply voltage, output current, and required clock performance.
Can AD9830AST be used for a communications local oscillator?
The AD9830AST can be used for a digitally controlled communications local oscillator because it combines a 32-bit tuning word with a 50 MHz maximum clock and dedicated frequency- and phase-modulation functions. In an RF design, the generated output must still be filtered, conditioned, and frequency-planned according to the system band. Reference-clock jitter and DDS phase noise remain system-level limitations.
What is the AD9830AST used for in test and measurement equipment?
The AD9830AST is used to generate precise, digitally programmed sine-wave excitation for test and measurement equipment. Its 32-bit tuning word provides fine frequency control, while the 10-bit DAC converts the digital phase and amplitude information into an analog waveform. An external reconstruction filter is normally required to remove images and harmonics introduced by the DAC output.
Where can I download the AD9830AST datasheet PDF?
The official AD9830 datasheet and product documentation are available through the Analog Devices AD9830 product page at analog.com/en/products/ad9830.html. Use the manufacturer document for the authoritative pin-description table, electrical characteristics, timing diagrams, recommended application circuit, and package drawings. The product page also links to the ADIsimDDS tool for calculating the frequency tuning word and estimating spectral performance.
Where can I find the AD9830AST pinout?
The AD9830AST pinout is documented in the pin-description table and package drawing in the Analog Devices AD9830 datasheet. The exact 48-terminal assignments should be transcribed from that document when laying out the PCB. Use pin names and numbers from the datasheet rather than relying on the 48-pin TQFP outline alone, because supply, ground, control, clock, and analog-output functions each require specific connections.
How much clock frequency can AD9830AST use?
The AD9830AST supports a maximum clock frequency of 50 MHz according to the Analog Devices product information. The actual output frequency depends on the relationship between the clock, the 32-bit frequency tuning word, and the DDS frequency-setting convention used by the device. The ADIsimDDS utility can calculate the required tuning word and provide an estimate of spectral performance.
What are the power and decoupling requirements for AD9830AST?
The AD9830AST requires a stable supply and appropriate local decoupling for reliable operation of its clock, digital control, and analog output sections. Place the supply and ground connections directly to their assigned package pins, and follow the capacitor values and layout shown in the manufacturer’s recommended application circuit. Keep switching-node and digital-interface return currents away from the analog output to reduce supply-induced noise.
What is the best drop-in replacement for AD9830AST?
AD9830ASTZ is the closest documented drop-in candidate because cross-reference information identifies the same 48-pin package, consistent terminals, and matching principal DDS characteristics. It remains a same-manufacturer ordering variant rather than a broader second-source solution. Before substitution, verify its temperature rating, supply limits, pin assignments, control timing, and lifecycle status against the AD9830AST design.
What can replace AD9830AST?
AD9830ASTZ can replace AD9830AST when the existing 48-lead TQFP land pattern, pin functions, and operating requirements remain unchanged. The replacement uses the same documented 10-bit DDS, 32-bit tuning-word, and 50 MHz clock architecture, and cross-reference information describes the terminals and package as consistent. No verified cross-brand drop-in replacement is identified on this page.
Is AD9830AST suitable for sensor testing and ultrasonic excitation?
The AD9830AST is suitable for sensor testing and ultrasonic excitation when a digitally controlled sine signal is required and the output frequency falls within the device’s DDS operating range. The 32-bit tuning word permits fine adjustment, and the 10-bit DAC provides the required digital-to-analog conversion stage. Drive the output through suitable gain and filtering stages rather than loading the DAC directly.
Where can I buy AD9830AST?
Use the Request a Quote form on this page to request AD9830AST availability, current pricing, and lead time for the obsolete ordering code. Because the part is listed as obsolete, supply and lifecycle status should be confirmed before a production commitment. The form is the appropriate route for quote, allocation, and obsolete-part sourcing without relying on a static listing price.
What is the price of AD9830AST?
Current AD9830AST pricing is not published as a fixed quantity-break table on this page because the exact obsolete ordering code requires a quotation. Submit the Request a Quote form with the required quantity, package preference, and target date. The platform handles current pricing separately, and the manufacturer documentation should be used to confirm technical suitability before purchase.
What is the lead time and stock status for AD9830AST?
The AD9830AST stock position and lead time should be obtained through the Request a Quote form on this page. The part is identified as obsolete, so availability may depend on remaining factory inventory, authorized channel availability, or previously manufactured lots. Provide the required quantity and assembly schedule so the sourcing team can confirm the latest allocation and delivery information.

Dados de referência de engenharia para AD9830AST — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the AD9830AST when maintaining a legacy design that specifically calls for this obsolete ordering code and requires a 10-bit DDS with a 32-bit tuning word, 50 MHz maximum clock, sine output, and frequency- or phase-modulation capability. AD9830ASTZ is the closest documented drop-in candidate because its terminals, package, and principal performance characteristics are consistent; use it when its ordering, temperature, finish, and lifecycle conditions satisfy the design. No verified cross-brand drop-in part is identified, so changing manufacturers would require a separate engineering review rather than a simple substitution. For new designs, compare the complete DDS function set, interface timing, supply voltage, clock-jitter requirements, output-current capability, package footprint, and end-of-life policy before selecting a device.

Comparação com alternativas

Parâmetro Este produto AD9830ASTZ
Package 48-lead TQFP, 7 x 7 mm 48-lead TQFP, 7 x 7 mm
Brand Analog Devices Analog Devices
Device Type Direct digital synthesizer Direct digital synthesizer
DAC Resolution 10 bit 10 bit
Maximum Clock Frequency 50 MHz 50 MHz
Frequency Tuning Word 32 bit 32 bit
Modulation Capability Frequency modulation and phase modulation Frequency modulation and phase modulation
Output Waveform Sine wave Sine wave

Principais diferenciais

  • Compact integration of the complete DDS signal path (vs AD9830ASTZ)
  • Fine digital frequency programming (vs AD9830ASTZ)
  • Dedicated modulation functions (vs AD9830ASTZ)

Notas de projeto

Route the reference clock and serial control signals away from the analog output and reconstruction-filter network to reduce coupling into the sine-wave signal. Follow the manufacturer’s recommended component placement for the supply, ground, clock, and DAC output pins. Ground-plane distribution should support the required return paths without placing high-current digital return currents beneath sensitive analog output nodes.

The DDS output contains images and harmonics associated with the 10-bit DAC and phase-accumulator architecture. Use a reconstruction filter selected for the required output band, and verify its cutoff, attenuation, and phase response across the operating range. Evaluate the filter against the 50 MHz maximum clock because a clock-related image may appear close to the desired output frequency.

Decouple the supply pins locally using the capacitor configuration shown in the manufacturer’s application circuit, and provide a low-impedance connection from each ground pin to the circuit ground plane. A clean reference clock is essential because clock phase noise can degrade DDS spectral performance. Measure output noise and spur levels with the final regulator, clock source, layout, and enclosure in place.

Do not infer pin compatibility from the package outline alone. Confirm every AD9830AST terminal against the manufacturer pin-description table, including supply, ground, clock, synchronization, serial-control, and analog-output functions. When considering AD9830ASTZ as a replacement, also verify ordering details, temperature grade, lead finish, and lifecycle requirements before committing the part to production.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The AD9830AST is listed as obsolete. Compliance attributes are not stated in the available manufacturer and distributor information and therefore remain unknown.

Dados verificados em: 2026-11-15 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

AD9830AST datasheet AD9830AST datasheet pdf AD9830AST pinout AD9830AST specifications Analog Devices AD9830AST AD9830AST 10 bit DDS AD9830AST 50 MHz AD9830AST 48 TQFP AD9830AST equivalent AD9830AST replacement AD9830AST vs AD9830ASTZ AD9830AST waveform generator AD9830AST price AD9830AST stock AD9830AST application circuit

Componentes & termos relacionados

Analog Devices AD9830AST AD9830ASTZ Direct digital synthesizer DDS Numerically controlled oscillator Phase accumulator Sine look-up table Digital-to-analog converter 10-bit DAC 32-bit frequency tuning word 50 MHz clock Frequency modulation Phase modulation 48-lead TQFP TQFP package family Surface-mount package CMOS integrated circuit Reconstruction filter Waveform generation Communications local oscillator Sensor test excitation Signal-generation IC Clock and timing IC Obsolete component status
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ