Analog Devices

ADF4117BRUZ-RL7 - 1.2 GHz RF PLL Synthesizer | Analog Devices

MPN: ADF4117BRUZ-RL7 ✓ Nakahanda
16-pin TSSOP, 0.173 inch (4.40 mm) body width Package 1.2 GHz Speed
MOQ: 1 |

ADF4117BRUZ-RL7 Ulas

Analog Devices ADF4117BRUZ-RL7 is an RF frequency-synthesizer integrated circuit with a maximum synthesizer frequency of 1.2 GHz, packaged in a 16-pin TSSOP. It is designed for local-oscillator generation in wireless transmitters and receivers, with an indicated reference-input range of 100 MHz to 300 MHz and an example output frequency of 200 MHz. Its single-channel architecture combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler.

A frequency synthesizer is a clock-and-timing integrated circuit that generates a stable, programmable output frequency from a reference signal. In the hierarchy of electronic components, the ADF4117 belongs to the clock generator and phase-locked-loop family, where a phase-locked loop compares a divided feedback signal with the divided reference signal. The charge pump drives the tuning voltage of a voltage-controlled oscillator, allowing integer and fractional division ratios to determine the output frequency.

The ADF4117 family's key features include a 1.2 GHz maximum RF input frequency, programmable A and B counters, programmable reference division, a precision charge pump, and a dual-modulus prescaler. These features allow the device to implement a local oscillator in RF up-conversion and down-conversion paths. The 16-pin TSSOP package supports compact surface-mount layouts while providing separate connections for reference, feedback, charge-pump output, digital programming, and power.

Technically, the synthesizer derives its output from a stable external reference through cascaded programmable dividers. The prescaler divides the RF feedback signal, while the A and B counters determine the required division ratio and reference divider establishes the comparison frequency. Correct lock behavior depends on stable reference routing, proper loop-filter design, controlled charge-pump current, and separation of sensitive analog and high-speed RF paths.

Typical applications include wireless receiver local oscillators, transmitter up-conversion chains, RF down-conversion stages, instrumentation equipment, and communication modules. The part is particularly relevant when a compact, programmable RF clock source is required within a 1.2 GHz operating envelope. Designers must also evaluate the external voltage-controlled oscillator, loop-filter components, reference quality, and required lock time.

For PCB implementation, place the reference and RF input paths on controlled-impedance routing and keep feedback traces away from charge-pump and digital programming nets. Use stable reference and loop-filter components, provide local bypass capacitance at the supply pins, and verify the external VCO tuning range before programming the synthesizer counters. These practices reduce phase-noise degradation, reference pulling, and acquisition-time variation.

This product page combines the exact ADF4117BRUZ-RL7 package information with practical guidance for RF layout, loop-filter implementation, local-oscillator design, and firmware programming. It also identifies documented same-footprint alternatives and highlights the parameter checks required when changing the device without modifying the PCB.

Mga alternatibo na pwedeng ilagay na ADF4117BRUZ-RL7 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok ADF4117BRUZ-RL7 (parehas na form factor at footprint) — pagkakaiba sa B Counter, Package, A Counter, Charge Pump, Prescaler.

Analog Devices
B Counter: Programmable
Package: 16-pin TSSOP, 0.173 inch (4.40 mm) width
Ikabit sa ADF4117BRUZ-RL7 →
Analog Devices
B Counter: 5-bit programmable
Package: 16-pin TSSOP, 4.40 mm width
A Counter: 5-bit programmable
Ikabit sa ADF4117BRUZ-RL7 →

ADF4116BRUZ

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-TSSOP (0.173", 4.40mm Width)
Clock/Frequency Synthesizer (RF) IC · Integer-N · 550 MHz · 1 · CMOS · Clock · 2:1 · Low-noise digital PFD

Magkontak para sa presyo

Tingnan ang Datasheet →

ADF4118BRUZ

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-TSSOP (0.173", 4.40mm Width)
Integer-N RF PLL frequency synthesizer · 3.0 GHz · +2.7 V to +5.5 V · 6.5 mA · 1 · Programmable · 5-bit programmable · Programmable

Magkontak para sa presyo

Tingnan ang Datasheet →

ADF4117BRUZ-RL7 Mga Spesipikasyon

Product Type RF clock/frequency synthesizer IC
Maximum RF Frequency 1.2 GHz
Reference Input Frequency Range 100 MHz to 300 MHz
Example Output Frequency 200 MHz
Architecture Single-channel integer-N PLL frequency synthesizer
Phase-Frequency Detector Low-noise digital PFD
Charge Pump Precision charge pump
Reference Divider Programmable
A Counter Programmable 5-bit counter
B Counter Programmable counter
Prescaler Programmable dual-modulus P/P+1 prescaler
Packhaging 16-pin TSSOP, 0.173 inch (4.40 mm) body width
Uri ng Pagpapasok Surface mount
Programming Interface Serial digital programming

Gabay sa Pin Configuration ng ADF4117BRUZ-RL7 16-pin tssop, 0.173 inch (4.40 mm) body width

Pin configuration para sa ADF4117BRUZ-RL7 (16-pin tssop, 0.173 inch (4.40 mm) body width package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 16-pin tssop, 0.173 inch (4.40 mm) body width package para sa ADF4117BRUZ-RL7

Wala ng detalyadong pinout data na magagamit para sa ADF4117BRUZ-RL7.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

ADF4117BRUZ-RL7 ay nararapat para sa 6 aplikasyons: Wireless Receiver Local Oscillator, RF Transmitter Up-Conversion, RF Down-Conversion Mixer, Instrumentation RF Signal Source, RF Communication Module, Industrial RF Test Equipment.

🌐

Wireless Receiver Local Oscillator

The ADF4117BRUZ-RL7 fits a wireless receiver local-oscillator block when the required feedback frequency can operate below the family's 1.2 GHz maximum. The low-noise digital phase-frequency detector compares the divided reference with the divided RF feedback, while the precision charge pump drives an external loop filter and voltage-controlled oscillator. Programmable A and B counters, reference division, and the dual-modulus P/P+1 prescaler provide flexible division-ratio generation. Designers should calculate the complete integer-N ratio and verify counter compatibility before programming the device.

📡

RF Transmitter Up-Conversion

In a transmitter up-conversion chain, the ADF4117BRUZ-RL7 can generate a programmable local oscillator for a mixer or quadrature modulator. Its 1.2 GHz maximum RF frequency covers a broad range of wireless and instrumentation bands, while the programmable divider chain permits precise selection of the feedback division ratio. The precision charge pump and low-noise phase-frequency detector support a controlled tuning loop. Board implementation should minimize phase-noise contributions through short RF routes, a clean charge-pump connection, and a carefully selected loop filter.

📻

RF Down-Conversion Mixer

The ADF4117BRUZ-RL7 can supply the programmable local oscillator used by an RF down-conversion mixer. By dividing the feedback signal with the prescaler and A/B counters, the PLL establishes the oscillator frequency required to translate a received RF channel to a lower intermediate frequency. This arrangement is useful in wireless receivers, test equipment, and communication modules. The external VCO must cover the required tuning range, and the reference and loop-filter components should be selected for the desired lock time and phase-noise performance.

🖥️

Instrumentation RF Signal Source

For instrumentation that requires a tunable RF reference, the ADF4117BRUZ-RL7 combines programmable frequency division with a 1.2 GHz operating envelope. It can form the synthesizer section of a compact signal source when paired with an external voltage-controlled oscillator and reference oscillator. Programmable A and B counters and the dual-modulus prescaler support multiple channel plans, while the 16-pin TSSOP package simplifies compact surface-mount construction. Accurate output quality still depends on the reference source, VCO tuning range, loop-filter design, and RF shielding.

🧩

RF Communication Module

The ADF4117BRUZ-RL7 is suitable for compact communication modules requiring a programmable RF local oscillator rather than a fixed-frequency source. Its single-channel PLL architecture supports programmable reference division and dual-modulus RF feedback division, allowing the same synthesizer approach to serve multiple product variants. The 16-pin TSSOP package is appropriate for high-density surface-mount boards, but RF performance depends on controlled-impedance routing and isolation from digital control signals. Firmware should validate every prescaler and counter combination before enabling the RF output.

🏭

Industrial RF Test Equipment

Industrial RF test equipment can use the ADF4117BRUZ-RL7 to create a programmable local-oscillator signal for mixer, receiver, and filter characterization. The device's 1.2 GHz maximum frequency supports many common RF test bands, and the programmable divider chain allows the instrument to change channel plans without redesigning the synthesizer hardware. A low-noise reference and carefully isolated RF layout are essential for repeatable measurements. The external loop filter should be tailored to the required step size, settling time, and close-in phase-noise target.

What is the ADF4117BRUZ-RL7?
The ADF4117BRUZ-RL7 is a single-channel RF frequency-synthesizer IC with a maximum operating frequency of 1.2 GHz in a 16-pin TSSOP package. According to the Analog Devices ADF4116/ADF4117/ADF4118 datasheet, the device combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler. It is intended primarily for RF local-oscillator generation in wireless receivers and transmitters.
What are the key specifications of ADF4117BRUZ-RL7 that engineers should know?
The principal specifications of the ADF4117BRUZ-RL7 are a 1.2 GHz maximum RF frequency, a 16-pin TSSOP package, programmable A and B counters, a programmable reference divider, and a dual-modulus P/P+1 prescaler. Analog Devices describes an indicated reference-input range of 100 MHz to 300 MHz, while a distributor application example identifies a 200 MHz output. The low-noise digital phase-frequency detector and precision charge pump support phase-locked-loop frequency generation.
Where can I download the ADF4117BRUZ-RL7 datasheet PDF?
The ADF4117BRUZ-RL7 datasheet PDF is available from Analog Devices through the ADF4116/ADF4117/ADF4118 family document at analog.com. The manufacturer document contains the architecture, counter organization, prescaler options, programming information, electrical characteristics, and pin descriptions. Use the manufacturer PDF as the controlling reference for wiring, supply limits, register addresses, and timing rather than relying on a distributor catalog summary.
Where can I find the ADF4117BRUZ-RL7 pinout?
The ADF4117BRUZ-RL7 pinout is shown in the pin-description table of the Analog Devices ADF4116/ADF4117/ADF4118 datasheet. The device uses a 16-pin TSSOP package. When assigning PCB tracks, cross-check every pin number and signal name against the manufacturer pin table, especially the supply pins, ground connections, reference input, RF feedback input, charge-pump output, and serial programming signals.
How is the ADF4117BRUZ-RL7 used in an RF local oscillator?
The ADF4117BRUZ-RL7 is used as the programmable divider and phase comparator inside a phase-locked loop. The reference signal is divided by the programmable reference divider, the feedback RF signal is divided by the prescaler and A/B counters, and the digital phase-frequency detector drives the precision charge pump. The charge-pump current charges an external loop filter that controls an external voltage-controlled oscillator, allowing the feedback divider to establish the requested output frequency.
What programming is required for the ADF4117BRUZ-RL7?
The ADF4117BRUZ-RL7 requires serial programming of the A counter, B counter, reference divider, prescaler, charge-pump current, and other control registers. According to the Analog Devices family datasheet, the architecture uses programmable A and B counters and a programmable reference divider together with a dual-modulus prescaler. Firmware should calculate valid division ratios, avoid unavailable prescaler values, and verify the lock status before treating the RF output as usable.
What is the difference between ADF4117BRUZ-RL7 and ADF4117BRUZ?
The ADF4117BRUZ-RL7 and ADF4117BRUZ identify the same ADF4117 frequency-synthesizer device with different order-code suffixes. The RL7 ordering code denotes the specific reel and temperature packaging configuration, while the base ADF4117BRUZ identifies the 16-pin TSSOP device without that complete ordering suffix. For electrical design, use the family datasheet and verify the exact order-code details in the Analog Devices product documentation before substitution.
Can ADF4116BRUZ replace ADF4117BRUZ-RL7 in the same PCB footprint?
The ADF4116BRUZ is a closely related member of the Analog Devices ADF411x family and uses the 16-pin TSSOP format, but it should not be treated as an unconditional substitute without a detailed register and electrical review. The family datasheet groups ADF4116, ADF4117, and ADF4118 together, yet their RF-frequency and programming details must be checked before reuse. Confirm pin functions, maximum operating conditions, counter behavior, and firmware support against the manufacturer documentation.
Is ADF4117BRUZ-RL7 suitable for a wireless receiver local oscillator?
The ADF4117BRUZ-RL7 is suitable for a wireless receiver local oscillator when the required RF frequency, reference arrangement, phase-noise target, and lock-time budget fall within the device's operating limits. The manufacturer specifically identifies local oscillators in receiver and transmitter up-conversion and down-conversion sections as intended applications. The external VCO, loop filter, reference source, and board layout remain critical to final RF performance.
When should I choose ADF4117BRUZ-RL7 over a lower-frequency PLL?
Choose the ADF4117BRUZ-RL7 when the RF feedback signal must operate within the family's 1.2 GHz maximum frequency and the design benefits from its programmable counters, dual-modulus prescaler, low-noise digital phase-frequency detector, and precision charge pump. A lower-frequency PLL may be preferable only when the actual RF requirement is substantially lower or when another device offers a more suitable prescaler range, reference architecture, package, or qualified operating-temperature range.
What is the best drop-in replacement for ADF4117BRUZ-RL7?
The closest documented drop-in candidates are the ADF4116BRUZ and ADF4118BRUZ because they belong to the same ADF411x family and use the 16-pin TSSOP format. A replacement should still pass a complete compatibility review covering pin functions, supply voltage, maximum RF frequency, counter organization, prescaler options, register addresses, lock behavior, and temperature grade. The available cross-reference information does not establish a broad set of independently verified cross-brand drop-ins.
Where can I buy ADF4117BRUZ-RL7 online?
The ADF4117BRUZ-RL7 can be requested through the Request a Quote form on this product page. The form is the appropriate route for current commercial terms, stock confirmation, lead time, minimum order quantity, and volume pricing. Avoid relying on historical catalog pricing when requesting a current quotation because component availability and commercial conditions can change over time.
What is the price of ADF4117BRUZ-RL7?
Current commercial pricing for the ADF4117BRUZ-RL7 should be obtained through the Request a Quote form on this page. The form requests the relevant quantity and supply configuration so XAIPART can return a current quotation and confirm logistics. Historical pricing may differ from current market conditions and should not be treated as a binding quotation for production procurement.
What is the lead time for ADF4117BRUZ-RL7?
The current lead time for the ADF4117BRUZ-RL7 should be confirmed through the Request a Quote form on this page. Include the required quantity, reel configuration, delivery location, and target production date in the request. A confirmed lead time allows the procurement plan to account for manufacturing schedules, incoming inspection, and any required component-planning buffer.
Is ADF4117BRUZ-RL7 in stock?
Current stock status for the ADF4117BRUZ-RL7 should be confirmed through the Request a Quote form on this page. Stock availability can vary by reel configuration, order quantity, and fulfillment date. Providing the required quantity and packaging details allows XAIPART to check the relevant channel and return an actionable supply response rather than an unverified availability claim.
What design considerations matter for an ADF4117BRUZ-RL7 RF layout?
The most important design considerations are stable reference routing, short RF feedback paths, controlled-impedance connections, careful separation of sensitive analog nodes from digital programming nets, and correctly designed loop-filter components. Place bypass capacitors close to the device's supply pins and keep the charge-pump trace short to minimize noise pickup. The Analog Devices family datasheet should be used with the selected VCO characteristics to establish valid counter ratios and reliable lock behavior.

Impormasyon ng Talumpati sa Engineering for ADF4117BRUZ-RL7 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the ADF4117BRUZ-RL7 when a wireless, instrumentation, or communication design needs a programmable RF local oscillator with operation up to 1.2 GHz and the established ADF411x divider architecture. Its 16-pin TSSOP format is appropriate for compact surface-mount equipment, while the low-noise digital phase-frequency detector, precision charge pump, programmable A and B counters, reference divider, and dual-modulus prescaler provide a flexible frequency plan. Consider the ADF4116BRUZ when its lower-frequency operating envelope better matches the target bands and a same-family register review is acceptable. Consider the ADF4118BRUZ when its frequency range provides a better fit, but review its maximum operating conditions and software implications. No cross-brand drop-in replacement is presented because the available cross-reference results do not establish verified pin and parameter compatibility for one. Final selection should also consider VCO tuning range, phase noise, lock time, reference quality, temperature grade, and PCB footprint.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto ADF4116BRUZ ADF4118BRUZ
Brand Analog Devices Analog Devices Analog Devices
Package 16-TSSOP (0.173", 4.40mm Width) 16-TSSOP (0.173", 4.40mm Width) 16-TSSOP (0.173", 4.40mm Width)
Product Type RF clock/frequency synthesizer IC RF clock/frequency synthesizer IC RF clock/frequency synthesizer IC
Phase-Frequency Detector Low-noise digital PFD Low-noise digital PFD Low-noise digital PFD
Charge Pump Precision charge pump Precision charge pump Precision charge pump
Counter Organization Programmable A and B counters Programmable A and B counters Programmable A and B counters
Prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler
Reference Divider Programmable Programmable Programmable
Programming Interface Serial digital programming Serial digital programming Serial digital programming

Pangunahing mga Pagkakaiba

  • Broad RF tuning envelope in a compact package (kumpara saADF4118BRUZ)
  • Programmable dual-modulus feedback division (kumpara saADF4116BRUZ)
  • Low-noise digital phase detection with precision charge pump (kumpara saADF4116BRUZ)

Talaan ng Disenyo

Keep the reference input and RF feedback routes short, continuous, and referenced to a stable ground plane. Route the charge-pump output directly to the loop-filter components because long or resistive traces can degrade phase noise and loop stability. Keep digital programming nets away from the reference, RF feedback, and charge-pump paths. Use via stitching where appropriate to maintain a low-impedance return path beneath high-frequency signals.

Do not treat every ADF411x order code as an unconditional substitute. Before replacing the ADF4117BRUZ-RL7, compare maximum RF frequency, supply limits, pin functions, counter widths, prescaler options, register addresses, lock-status behavior, and temperature grade. Firmware must be updated or revalidated for the selected device, and the complete frequency plan must be checked to ensure that the programmed integer-N ratio is valid.

Place the device's supply bypass capacitors immediately adjacent to the relevant power and ground pins, following the pin table and recommended-layout material in the manufacturer datasheet. Provide a low-impedance ground return for the charge pump and digital section, and decouple any separately filtered analog supply where the pinout permits it. Verify settling time at power-up before enabling sensitive downstream RF circuits.

Design the loop filter around the selected VCO gain, tuning range, phase detector gain, charge-pump current, reference frequency, and required lock time. Calculate the complete feedback division ratio from the prescaler and A/B counter settings rather than entering the target frequency alone. After assembly, verify reference lock, VCO tuning range, output phase noise, spurious levels, and recovery after a reference or RF-feedback disturbance.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No specific environmental or automotive compliance declaration appears in the cited product-page snippets. Confirm the current compliance statements and ordering information with Analog Devices before production release.

Data napatotohanan sa: 2026-11-15 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

ADF4117BRUZ-RL7 datasheet ADF4117BRUZ-RL7 pinout ADF4117BRUZ-RL7 datasheet pdf ADF4117BRUZ-RL7 equivalent ADF4117BRUZ-RL7 replacement ADF4117BRUZ-RL7 cross reference ADF4117BRUZ-RL7 footprint ADF4117BRUZ-RL7 programming ADF4117BRUZ-RL7 price ADF4117BRUZ-RL7 stock ADF4117BRUZ-RL7 vs ADF4116BRUZ ADF4117 1.2GHz TSSOP PLL ADF4117 RF local oscillator Analog Devices ADF4117

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices ADF4117 ADF4117BRUZ-RL7 ADF4116BRUZ ADF4118BRUZ frequency synthesizer clock generator phase-locked loop PLL integer-N synthesizer local oscillator RF up-conversion RF down-conversion phase-frequency detector precision charge pump dual-modulus prescaler P/P+1 prescaler programmable A counter programmable B counter reference divider 16-pin TSSOP TSSOP package family surface-mount package voltage-controlled oscillator 1.2 GHz
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ