ADM208EARU - 230kbps 4-Channel RS-232 | Analog Devices
MPN: ADM208EARU ✓ NakahandaADM208EARU Ulas
An RS-232 transceiver is an interface IC that translates logic-level digital signals into RS-232 line levels and converts incoming line-level signals back into logic-level outputs. The ADM2xxE family belongs to the RS-232 transceiver hierarchy within interface ICs and broader semiconductor signal-conditioning devices. These devices bridge modern controller logic and the voltage, noise-immune signaling used by older computer, industrial, instrumentation, and communications equipment.
Key features include four RS-232 drivers, four RS-232 receivers, operation from one 5 V supply, and a maximum data rate of 230 kbps. According to the Analog Devices ADM208E product information, the family conforms to the EIA-232E and CCITT V.28 specifications. The ADM208EARU also belongs to the robust ADM2xxE product family, which is associated with EMI/EMC compliance and ±15 kV ESD protection. Its 24-lead TSSOP format supports compact PCB layouts while retaining separate driver and receiver channels.
Technically, the driver channels provide the bipolar voltage swings required for RS-232 communication, while the receiver channels detect and translate incoming line states into CMOS-compatible logic. The 5 V-only architecture simplifies system power design compared with dual-supply RS-232 solutions. Because RS-232 is a point-to-point, unbalanced interface, correct grounding, cable length, connector selection, and protection-network design remain important system-level considerations even when the IC itself is robust.
Typical uses include industrial control links, test and measurement equipment, data acquisition systems, service interfaces, point-of-sale equipment, and embedded systems that retain an RS-232 port. The four transmitters and four receivers make the device especially useful where multiple serial channels must be accommodated without using four separate single-channel transceivers. Systems can also assign unused channels or operate them in one-way configurations when the application does not require four full duplex links.
Place the device close to the RS-232 connector and route the high-voltage driver outputs directly toward protected connector pins. Keep logic-side traces away from these outputs to minimize capacitive coupling and crosstalk. Use the manufacturer pin-description table when assigning supply, ground, enable, shutdown, driver-output, and receiver-input nets, and follow the datasheet layout guidance for external protection components and bypass capacitance.
This product page combines the official family specifications with practical channel-assignment, signal-routing, and replacement guidance. It also helps engineers distinguish the ADM208EARU from lower-channel RS-232 devices that use different packages or pin assignments, supporting faster component selection before PCB layout begins.
Mga alternatibo na pwedeng ilagay na ADM208EARU — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboADM208EARU Mga Spesipikasyon
| Product Type | Full RS-232 transceiver |
| Number of Transmit Channels | 4 channels |
| Number of Receive Channels | 4 channels |
| Volte ng Pagbibigay | 5 V |
| Maximum Data Rate | 230 kbps |
| Interface Standard | EIA-232E and CCITT V.28 |
| Packhaging | 24-lead TSSOP |
| Uri ng Pagpapasok | Surface mount |
| ESD Protection | ±15 kV |
| EMI/EMC Status | EMI/EMC-compliant family |
| Driver Output Type | RS-232 line driver |
| Receiver Input Type | RS-232 line receiver |
Gabay sa Pin Configuration ng ADM208EARU 24-lead tssop
Pin configuration para sa ADM208EARU (24-lead tssop package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ADM208EARU.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADM208EARU ay nararapat para sa 6 aplikasyons: Industrial Controller Serial Ports, Data Acquisition Equipment, Test and Measurement Instruments, Embedded Service Interfaces, Point-of-Sale Terminals, Communications and Networking Equipment.
Industrial Controller Serial Ports
The ADM208EARU is appropriate for industrial controllers that must retain several RS-232 connections while using a single 5 V supply. Its four transmitters and four receivers can form two full-duplex links or support separate command and data paths. The 230 kbps maximum rate covers conventional equipment-control traffic, while EIA-232E and CCITT V.28 conformity provides a defined basis for interoperability. Place the IC near the serial connector, route line-driver outputs away from controller logic, and add the protection components recommended by the manufacturer before the external connector.
Inirekomenda
Data Acquisition Equipment
The ADM208EARU can consolidate communication channels in laboratory and industrial data-acquisition equipment that connects controllers, sensors, and service interfaces. Four receiver channels are useful for status or command signals, while the drivers support outbound data connections. Operation from one 5 V rail simplifies acquisition-system power distribution, and the 230 kbps limit is suitable for many configuration and monitoring links. Maintain separation between logic traces and RS-232 driver outputs, use a stable common ground, and confirm every receiver and driver connection against the official 24-pin diagram.
Inirekomenda
Test and Measurement Instruments
The ADM208EARU fits test and measurement instruments requiring several RS-232 service or control ports in restricted board space. The four transmitters and four receivers permit two bidirectional instrument links or multiple one-way channels, reducing the number of separate transceiver packages. Its 230 kbps maximum data rate supports conventional instrument-control traffic, while single 5 V operation simplifies front-panel and embedded controller power plans. Route each protected line toward the connector and keep sensitive measurement circuitry away from the high-swing driver outputs.
Inirekomenda
Embedded Service Interfaces
The ADM208EARU can support legacy service and configuration interfaces in embedded systems that still communicate with RS-232 peripherals. Four driver channels allow separate outbound paths, while four receiver channels can monitor acknowledgements, status signals, or multiple peripheral buses. The 5 V-only architecture reduces supply complexity compared with a dual-rail implementation. Engineers should terminate or handle unused channels according to the datasheet, preserve adequate connector-to-IC spacing for protection components, and verify that the system ground strategy is compatible with the connected equipment.
Inirekomenda
Point-of-Sale Terminals
The ADM208EARU fits point-of-sale and peripheral systems that need more than one legacy serial connection but prefer one consolidated interface package. Two full-duplex ports can connect a terminal and peripheral, or the eight channels can be assigned for printers, scanners, status devices, and service connections. Operation up to 230 kbps is suitable for conventional transactional peripherals. The 24-lead TSSOP footprint requires disciplined high-voltage line routing, and ESD protection should be placed close to exposed connectors rather than relying only on the IC's internal protection.
Inirekomenda
Communications and Networking Equipment
The ADM208EARU is suitable for communications equipment with legacy management, diagnostic, or terminal interfaces that must coexist with modern digital circuitry. Four drivers and four receivers provide flexible channel allocation for management commands, diagnostic outputs, and incoming status signals. Its EIA-232E and CCITT V.28 conformity supports standardized RS-232 behavior, and the single 5 V supply simplifies interface design. High-swing driver nets should be treated as signal-integrity-sensitive routes, with short paths to protected connectors and adequate separation from clocks, sensors, and analog inputs.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADM208EARU — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Analog Devices |
| Package | 24-lead TSSOP |
| Transmitter Channels | 4 channels |
| Receiver Channels | 4 channels |
| Supply Voltage | 5 V |
| Maximum Data Rate | 230 kbps |
| Interface Standards | EIA-232E and CCITT V.28 |
| ESD Protection | ±15 kV |
Pangunahing mga Pagkakaiba
- Higher channel density than a 2/2 RS-232 transceiver (kumpara saADM202EARU)
- Single-package consolidation for multi-port RS-232 designs (kumpara saADM202EARU)
- Standards-oriented interface operation (kumpara saADM202EARU)
Talaan ng Disenyo
Place the ADM208EARU close to the RS-232 connector and route driver outputs directly to the protected connector pins. Keep these high-swing nets away from receiver inputs, clocks, and sensitive logic so that capacitive coupling does not create false transitions. Use the manufacturer's pin-description table to locate all supply, ground, control, driver, and receiver terminals before finalizing the footprint.
Do not substitute the ADM202EARU for the ADM208EARU: the former has two transmitters and two receivers in 16 leads, whereas the ADM208EARU has four of each in 24 leads. Likewise, do not assume that enable or shutdown functions present on other ADM2xxE members use the same pins on this device. Verify the exact ordering code, pin table, and no-connect assignments against the manufacturer documentation.
Keep external protection components close to the connector and follow the manufacturer reference layout. Maintain a deliberate ground strategy for the RS-232 interface and minimize loop area around every protected line. The family is associated with ±15 kV ESD protection and EMI/EMC compliance, but connector-level system performance still depends on cable routing, enclosure behavior, grounding, and the selected surge-protection network.
Impormasyon ng Pagsunod sa Kautusan
The ADM2xxE family is identified as EMI/EMC-compliant and associated with ±15 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for ADM208EARU are not stated in the public product material.