Analog Devices

ADM208EARU - 230kbps 4-Channel RS-232 | Analog Devices

料号: ADM208EARU ✓ 量产中
5 V Vdss 24-lead TSSOP Package
最小起订量: 1 |

ADM208EARU 概述

The Analog Devices ADM208EARU is a four-driver, four-receiver full RS-232 interface transceiver operating from a single 5 V supply at data rates up to 230 kbps. The device is offered in a 24-lead TSSOP package and is designed for robust EIA-232E and CCITT V.28 serial-interface applications. It integrates four transmit channels and four receive channels, allowing two complete RS-232 links or several unidirectional data paths to be implemented in a compact surface-mount design.

An RS-232 transceiver is an interface IC that translates logic-level digital signals into RS-232 line levels and converts incoming line-level signals back into logic-level outputs. The ADM2xxE family belongs to the RS-232 transceiver hierarchy within interface ICs and broader semiconductor signal-conditioning devices. These devices bridge modern controller logic and the voltage, noise-immune signaling used by older computer, industrial, instrumentation, and communications equipment.

Key features include four RS-232 drivers, four RS-232 receivers, operation from one 5 V supply, and a maximum data rate of 230 kbps. According to the Analog Devices ADM208E product information, the family conforms to the EIA-232E and CCITT V.28 specifications. The ADM208EARU also belongs to the robust ADM2xxE product family, which is associated with EMI/EMC compliance and ±15 kV ESD protection. Its 24-lead TSSOP format supports compact PCB layouts while retaining separate driver and receiver channels.

Technically, the driver channels provide the bipolar voltage swings required for RS-232 communication, while the receiver channels detect and translate incoming line states into CMOS-compatible logic. The 5 V-only architecture simplifies system power design compared with dual-supply RS-232 solutions. Because RS-232 is a point-to-point, unbalanced interface, correct grounding, cable length, connector selection, and protection-network design remain important system-level considerations even when the IC itself is robust.

Typical uses include industrial control links, test and measurement equipment, data acquisition systems, service interfaces, point-of-sale equipment, and embedded systems that retain an RS-232 port. The four transmitters and four receivers make the device especially useful where multiple serial channels must be accommodated without using four separate single-channel transceivers. Systems can also assign unused channels or operate them in one-way configurations when the application does not require four full duplex links.

Place the device close to the RS-232 connector and route the high-voltage driver outputs directly toward protected connector pins. Keep logic-side traces away from these outputs to minimize capacitive coupling and crosstalk. Use the manufacturer pin-description table when assigning supply, ground, enable, shutdown, driver-output, and receiver-input nets, and follow the datasheet layout guidance for external protection components and bypass capacitance.

This product page combines the official family specifications with practical channel-assignment, signal-routing, and replacement guidance. It also helps engineers distinguish the ADM208EARU from lower-channel RS-232 devices that use different packages or pin assignments, supporting faster component selection before PCB layout begins.

直接替换替代料: ADM208EARU ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

该产品暂无直接替换替代料。

请求替代料

ADM208EARU 规格参数

Product Type Full RS-232 transceiver
Number of Transmit Channels 4 channels
Number of Receive Channels 4 channels
电源电压 5 V
Maximum Data Rate 230 kbps
Interface Standard EIA-232E and CCITT V.28
封装 24-lead TSSOP
安装类型 Surface mount
ESD Protection ±15 kV
EMI/EMC Status EMI/EMC-compliant family
Driver Output Type RS-232 line driver
Receiver Input Type RS-232 line receiver

ADM208EARU 24-lead tssop 引脚配置指南

ADM208EARU(24-lead tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ADM208EARU 的 24-lead tssop 封装引脚图

暂无详细引脚数据: ADM208EARU.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADM208EARU 适用于 6 应用s: Industrial Controller Serial Ports, Data Acquisition Equipment, Test and Measurement Instruments, Embedded Service Interfaces, Point-of-Sale Terminals, Communications and Networking Equipment.

🏭

Industrial Controller Serial Ports

The ADM208EARU is appropriate for industrial controllers that must retain several RS-232 connections while using a single 5 V supply. Its four transmitters and four receivers can form two full-duplex links or support separate command and data paths. The 230 kbps maximum rate covers conventional equipment-control traffic, while EIA-232E and CCITT V.28 conformity provides a defined basis for interoperability. Place the IC near the serial connector, route line-driver outputs away from controller logic, and add the protection components recommended by the manufacturer before the external connector.

🖥️

Data Acquisition Equipment

The ADM208EARU can consolidate communication channels in laboratory and industrial data-acquisition equipment that connects controllers, sensors, and service interfaces. Four receiver channels are useful for status or command signals, while the drivers support outbound data connections. Operation from one 5 V rail simplifies acquisition-system power distribution, and the 230 kbps limit is suitable for many configuration and monitoring links. Maintain separation between logic traces and RS-232 driver outputs, use a stable common ground, and confirm every receiver and driver connection against the official 24-pin diagram.

🔧

Test and Measurement Instruments

The ADM208EARU fits test and measurement instruments requiring several RS-232 service or control ports in restricted board space. The four transmitters and four receivers permit two bidirectional instrument links or multiple one-way channels, reducing the number of separate transceiver packages. Its 230 kbps maximum data rate supports conventional instrument-control traffic, while single 5 V operation simplifies front-panel and embedded controller power plans. Route each protected line toward the connector and keep sensitive measurement circuitry away from the high-swing driver outputs.

🔧

Embedded Service Interfaces

The ADM208EARU can support legacy service and configuration interfaces in embedded systems that still communicate with RS-232 peripherals. Four driver channels allow separate outbound paths, while four receiver channels can monitor acknowledgements, status signals, or multiple peripheral buses. The 5 V-only architecture reduces supply complexity compared with a dual-rail implementation. Engineers should terminate or handle unused channels according to the datasheet, preserve adequate connector-to-IC spacing for protection components, and verify that the system ground strategy is compatible with the connected equipment.

🖥️

Point-of-Sale Terminals

The ADM208EARU fits point-of-sale and peripheral systems that need more than one legacy serial connection but prefer one consolidated interface package. Two full-duplex ports can connect a terminal and peripheral, or the eight channels can be assigned for printers, scanners, status devices, and service connections. Operation up to 230 kbps is suitable for conventional transactional peripherals. The 24-lead TSSOP footprint requires disciplined high-voltage line routing, and ESD protection should be placed close to exposed connectors rather than relying only on the IC's internal protection.

🌐

Communications and Networking Equipment

The ADM208EARU is suitable for communications equipment with legacy management, diagnostic, or terminal interfaces that must coexist with modern digital circuitry. Four drivers and four receivers provide flexible channel allocation for management commands, diagnostic outputs, and incoming status signals. Its EIA-232E and CCITT V.28 conformity supports standardized RS-232 behavior, and the single 5 V supply simplifies interface design. High-swing driver nets should be treated as signal-integrity-sensitive routes, with short paths to protected connectors and adequate separation from clocks, sensors, and analog inputs.

What is the ADM208EARU?
The ADM208EARU is a four-transmitter, four-receiver full RS-232 transceiver from Analog Devices. It operates from a single 5 V supply and supports data rates up to 230 kbps in a 24-lead TSSOP package. According to the Analog Devices ADM208E product information, the device conforms to the EIA-232E and CCITT V.28 specifications, making it suitable for multi-channel RS-232 links in industrial, instrumentation, and embedded equipment.
How many RS-232 channels does ADM208EARU have?
The ADM208EARU contains four RS-232 driver channels and four receiver channels. This arrangement can support two full-duplex RS-232 links or up to eight independently assigned directional channels within a single 24-lead TSSOP device. The distributor listing identifies the exact ADM208EARU configuration as a 4/4 full RS-232 transceiver, while the Analog Devices family page confirms that the ADM2xxE family operates from one 5 V supply.
What is the maximum data rate of ADM208EARU?
The ADM208EARU supports data rates up to 230 kbps. According to the Analog Devices ADM208E product information, this rate applies across the robust ADM2xxE RS-232 and V.28 interface family. The rate is suitable for conventional serial links, embedded service ports, and industrial equipment interfaces that operate below the device's stated maximum.
What supply voltage does ADM208EARU require?
The ADM208EARU operates from a single 5 V power supply. This simplifies the system power architecture because designers do not need separate positive and negative supplies for the RS-232 line interface. According to the Analog Devices product description, the single-supply ADM2xxE family is designed for EIA-232E and CCITT V.28 communication in both industrial and instrumentation applications.
Where can I download the ADM208EARU datasheet PDF?
The official ADM208E product page is the primary source for the ADM208EARU datasheet and related technical information. It identifies the device as part of the ADM2xxE family and provides family specifications, including single 5 V operation and operation up to 230 kbps. Use the Analog Devices page to select the exact ADM208EARU ordering code before assigning its 24-lead TSSOP pin functions during schematic design.
Where can I find the ADM208EARU pinout?
The ADM208EARU pin assignments are documented in the manufacturer's ADM208E datasheet under the pin-description and connection-diagram information for the 24-lead TSSOP package. Use that table to identify supply, ground, enable, shutdown, driver outputs, and receiver inputs before routing the PCB. The public search material confirms the 24-lead TSSOP package but does not reproduce every numbered terminal, so verify each net against the official diagram.
Is ADM208EARU the same as ADM202EARU?
No. The ADM208EARU is a four-driver, four-receiver transceiver in a 24-lead TSSOP, while the ADM202EARU is a two-driver, two-receiver device in a 16-lead TSSOP. Their channel counts and package pin counts differ, so ADM202EARU is not a direct drop-in replacement. The distinction matters when consolidating multiple RS-232 ports or when preserving an existing PCB footprint.
What is the best drop-in replacement for ADM208EARU?
The closest drop-in candidate is an ordering variant that preserves the same ADM208E electrical design and 24-lead TSSOP footprint, such as ADM208EARU-REEL7, subject to package and ordering-code verification. The cross-reference results do not identify another manufacturer with a confirmed 24-pin, four-driver, four-receiver, 5 V RS-232 implementation. Validate enable, shutdown, channel, and exposed/no-connect assignments against the datasheet before approving any substitute.
Can ADM208EARU replace ADM202EARU?
The ADM208EARU cannot directly replace the ADM202EARU on an unmodified PCB because the ADM208EARU has four transmit and four receive channels in 24 leads, while the ADM202EARU has two of each in 16 leads. The larger package changes the footprint and pin count. A board redesign or a confirmed 24-lead pin-compatible device is required rather than a simple component substitution.
When should I choose ADM208EARU over a 2/2 RS-232 transceiver?
Choose the ADM208EARU when the design needs four driver and four receiver channels in one 24-lead TSSOP. A 2/2 transceiver is more appropriate for one or two links and can reduce package count and board area in simpler systems. The ADM208EARU consolidates channel count but requires careful routing of eight RS-232-side connections and attention to unused-channel configuration.
Is ADM208EARU suitable for industrial equipment?
The ADM208EARU is suitable for industrial and instrumentation interfaces requiring RS-232 connectivity at up to 230 kbps. The Analog Devices family information confirms EIA-232E and CCITT V.28 conformity, single 5 V operation, and a robust ADM2xxE product positioning. The associated family material also identifies ±15 kV ESD protection and EMI/EMC compliance, making the device appropriate for protected equipment links when the complete system grounding and cable design are correct.
How should ADM208EARU be laid out for EMC performance?
Place the ADM208EARU close to the RS-232 connector and route each driver output directly toward its connector and protection network. Keep logic-side receiver traces and clocks away from high-swing driver nets to reduce capacitive coupling. Connect the interface ground according to the application topology, use the package pin table for bypass pins, and preserve the manufacturer's recommended protection-component arrangement.
Does ADM208EARU support shutdown or enable control?
The ADM208E family information states that shutdown and enable controls are provided on some products, but the public search material does not establish which control functions are assigned specifically to ADM208EARU. Consult the ADM208EARU pin-description table before using either function in a power-sequencing scheme. Do not assume that a control shown for another ADM2xxE member is present or wired identically on this exact device.
Where can I buy ADM208EARU and what is its lead time?
Use the Request a Quote form on this page to request ADM208EARU availability, current lead time, order quantity, and package quantity. The manufacturer maintains an official ADM208E product page, and current distributor listings identify the exact 24-lead TSSOP device. Stock and lead time can change, so obtain a written quotation for the quantity and date required by the build schedule.
What are the key specifications of ADM208EARU that engineers should know?
The principal ADM208EARU specifications are four transmit channels, four receive channels, single 5 V operation, a maximum rate of 230 kbps, EIA-232E and CCITT V.28 conformity, and a 24-lead TSSOP package. The ADM2xxE family is also associated with ±15 kV ESD protection and EMI/EMC compliance. These parameters define its role as a consolidated, multi-channel RS-232 interface rather than a general-purpose logic device.

工程参考数据: ADM208EARU ——对比、设计指导和合规信息。

选型指南

Choose ADM208EARU when the design requires four RS-232 driver channels and four receiver channels in a 24-lead TSSOP, particularly when consolidating two full-duplex ports or several one-way links. Choose a two-channel transceiver such as ADM202EARU when only one or two links are needed and a smaller 16-lead footprint is preferable; it is not a direct replacement because the package and channel assignments differ. Choose a single-channel RS-232 transceiver when PCB area, cost, or unused-channel simplicity matters more than channel consolidation. For any substitute, verify the exact package, all 24 pin assignments, 5 V supply requirement, data rate, control pins, and line-side protection. The ADM208EARU is strongest when channel count and standard 230 kbps RS-232 operation justify a larger interface package.

与替代料对比

参数 本产品
Brand Analog Devices
Package 24-lead TSSOP
Transmitter Channels 4 channels
Receiver Channels 4 channels
Supply Voltage 5 V
Maximum Data Rate 230 kbps
Interface Standards EIA-232E and CCITT V.28
ESD Protection ±15 kV

关键差异点

  • Higher channel density than a 2/2 RS-232 transceiver (对比 ADM202EARU)
  • Single-package consolidation for multi-port RS-232 designs (对比 ADM202EARU)
  • Standards-oriented interface operation (对比 ADM202EARU)

设计说明

Place the ADM208EARU close to the RS-232 connector and route driver outputs directly to the protected connector pins. Keep these high-swing nets away from receiver inputs, clocks, and sensitive logic so that capacitive coupling does not create false transitions. Use the manufacturer's pin-description table to locate all supply, ground, control, driver, and receiver terminals before finalizing the footprint.

Do not substitute the ADM202EARU for the ADM208EARU: the former has two transmitters and two receivers in 16 leads, whereas the ADM208EARU has four of each in 24 leads. Likewise, do not assume that enable or shutdown functions present on other ADM2xxE members use the same pins on this device. Verify the exact ordering code, pin table, and no-connect assignments against the manufacturer documentation.

Keep external protection components close to the connector and follow the manufacturer reference layout. Maintain a deliberate ground strategy for the RS-232 interface and minimize loop area around every protected line. The family is associated with ±15 kV ESD protection and EMI/EMC compliance, but connector-level system performance still depends on cable routing, enclosure behavior, grounding, and the selected surge-protection network.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The ADM2xxE family is identified as EMI/EMC-compliant and associated with ±15 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for ADM208EARU are not stated in the public product material.

相关搜索

ADM208EARU datasheet ADM208EARU pinout ADM208EARU datasheet pdf ADM208EARU specifications ADM208EARU equivalent ADM208EARU replacement ADM208EARU cross reference ADM208EARU 24-TSSOP ADM208EARU 230kbps RS-232 ADM208EARU price ADM208EARU stock Analog Devices ADM208EARU ADM208EARU vs ADM202EARU ADM208EARU industrial serial interface what does ADM208EARU do

相关元器件 & 术语

Analog Devices ADM208EARU ADM208E ADM2xxE RS-232 transceiver line driver line receiver EIA-232E CCITT V.28 interface IC semiconductor CMOS logic 5 V power supply 230 kbps 24-lead TSSOP TSSOP package family surface-mount package RS-232 interface industrial control data acquisition test and measurement ±15 kV ESD protection EMI/EMC compliance
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情