ADS1286PC - 12-Bit 20kHz Micropower SAR ADC | Texas Instruments
MPN: ADS1286PC ✗ Tapus ng BuhayADS1286PC Ulas
A sampling ADC is an analog-to-digital converter that acquires an input voltage with a sample-and-hold circuit before conversion. The ADS1286 belongs to the ADC, data converter, and signal-processing semiconductor hierarchy. Its differential input allows a sensor output to be measured relative to a reference node, which can improve rejection of common-mode noise when the signal source, analog ground, and digital return paths are designed carefully.
The converter provides 12-bit resolution and a maximum sampling rate of 20 kSPS. A differential input, integrated sample-and-hold amplifier, and low 250 µA supply current make the device suitable for compact, battery-powered measurement systems. The serial interface supports SPI and SSI-compatible operation, allowing the ADC to communicate with microcontrollers and other digital controllers over a small number of signal lines.
The ADS1286 uses a successive-approximation-register conversion architecture. This approach supports a compact implementation and efficient conversion timing while avoiding the higher power and complexity commonly associated with continuously operating high-speed conversion architectures. Its two-wire or three-wire serial interface reduces board-routing requirements, which is valuable where connector pins, PCB area, and standby power are constrained.
Typical applications include remote sensor acquisition, industrial process measurement, portable instrumentation, battery-operated data loggers, and low-power embedded monitoring systems. The ADS1286 is particularly appropriate when measurements must be captured locally and transferred through a serial interface rather than through a parallel data bus. The 250 µA supply-current characteristic also helps limit average system energy when the converter is operated intermittently.
Designers should follow the manufacturer datasheet for analog input range, reference voltage, acquisition timing, bypass-capacitor values, and digital-interface timing. Input and reference grounds should be kept quiet, and the serial clock should be driven only while data is required if the host processor cannot shut down its output pins between conversions.
This page combines the manufacturer device description, ordering information, package details, interface characteristics, drop-in replacement findings, and practical selection guidance to support faster engineering decisions for the ADS1286PC 12-bit micropower sampling ADC.
Mga alternatibo na pwedeng ilagay na ADS1286PC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ADS1286PC (parehas na form factor at footprint) — pagkakaiba sa Input Type, Supply Current.
ADS1286P
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →ADS1286PC Mga Pinakamataas na Rating at Electrical Characteristics
| Pangangasiwaan | 12 bit |
| Rate ng Pagkupita | 20 kSPS |
| Architecture | Successive-approximation register (SAR) |
| Input Type | 1 differential input |
| Input Stage | Sample-and-hold amplifier |
| Kuru-kuryente ng Pagbibigay | 250 µA |
| Serial Interface | SPI and SSI compatible |
| Interface Wiring | 2-wire or 3-wire |
| Packhaging | 8-pin PDIP |
| Uri ng Pagpapasok | Through-hole |
| Volte ng Pagbibigay | 4.5 V |
| Tindminan RoHS | Compliant |
Gabay sa Pin Configuration ng ADS1286PC 8-pin pdip
Pin configuration para sa ADS1286PC (8-pin pdip package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa ADS1286PC.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADS1286PC ay nararapat para sa 6 aplikasyons: Remote Sensor Acquisition, Battery-Powered Data Logging, Industrial Process Measurement, Portable Instrumentation, Battery Management Monitoring, Embedded Condition Monitoring.
Remote Sensor Acquisition
The ADS1286PC fits remote sensor acquisition when a sensor produces a differential signal and the measurement system must conserve power. Its 12-bit resolution and 20 kSPS maximum sampling rate provide sufficient conversion capability for many pressure, temperature, and position sensing conditions, while the 250 µA supply current is appropriate for battery-powered remote nodes. The SPI- or SSI-compatible serial interface reduces the number of wiring paths between the converter and a remote controller. Differential measurement also helps represent the sensor voltage relative to a common reference node, although input range and common-mode limits must be checked in the manufacturer datasheet. Place the converter and its input network near the sensor to minimize interference on the low-level analog path.
Inirekomenda
Battery-Powered Data Logging
The ADS1286PC is useful in battery-powered data loggers that periodically capture analog measurements and then transmit the results through a serial link. Its 12-bit resolution and 20 kSPS capability support measurement streams without the continuous conversion burden of a flash or pipeline ADC, while the 250 µA supply current supports low-power operation. The two-wire or three-wire interface minimizes both connector usage and microcontroller I/O requirements. For best results, operate the converter only during acquisition windows and deassert or gate digital interface lines when the host can remain active. Battery life should be evaluated using the average supply current, conversion rate, and duty cycle rather than the typical operating current alone.
Inirekomenda
Industrial Process Measurement
The ADS1286PC can serve as the acquisition element in compact industrial process-measurement equipment when 12-bit resolution and 20 kSPS are sufficient for the monitored variable. The differential input supports a sensor-to-reference measurement arrangement, and the serial interface allows a local controller to collect readings without requiring a wide parallel bus. The 250 µA supply current is valuable in distributed instrumentation where each measurement node has a limited power budget. Industrial equipment should still address electrical isolation, surge protection, grounding, and calibration separately from the converter itself. Keep analog routing compact, use the reference and bypass network specified by the manufacturer, and confirm that the input signal remains inside the supported common-mode and absolute-maximum ranges.
Inirekomenda
Portable Instrumentation
The ADS1286PC is appropriate for handheld or portable instrumentation where a low-power, compact ADC is needed close to the sensor or analog front end. Its 12-bit conversion resolution is suitable for many monitoring, calibration, and status functions, while the 20 kSPS rate allows rapid measurements when required. The 8-pin PDIP package is easy to prototype and socket for instrument repair, although a permanently mounted production design should account for mechanical stability and board cleanliness. SPI- and SSI-compatible operation provides flexibility with common embedded controllers. The low 250 µA supply-current specification helps preserve battery life, but the complete instrument also includes sensor excitation, display, communications, and regulator losses that must be included in a realistic power budget.
Inirekomenda
Battery Management Monitoring
The ADS1286PC can monitor a battery-derived analog signal in energy-management equipment when the required accuracy and bandwidth are modest. Its 12-bit resolution provides 4096 discrete code levels, and the 250 µA supply current helps prevent the measurement circuit from dominating the standby budget. The differential input can measure a scaled cell or supply voltage relative to a reference node, while the serial interface transfers readings to a charger or monitoring controller. The actual input range and reference arrangement determine whether direct battery sensing is safe, so use the manufacturer electrical limits rather than assuming the full battery range is supported. Add the external divider, filtering, and protection-network losses when calculating the complete measurement path's energy use.
Inirekomenda
Embedded Condition Monitoring
The ADS1286PC fits embedded condition-monitoring modules that periodically sample a differential sensor output and report it to a local controller. A 20 kSPS maximum rate provides flexibility for both slow monitoring values and faster transient capture, while 12-bit resolution supports many common vibration, thermal, and analog status measurements. The micropower 250 µA supply current is valuable in embedded installations where service access is limited. Use the SPI- or SSI-compatible interface to reduce wiring overhead, and synchronize acquisition with the controller to avoid unnecessary conversions. Signal integrity depends on keeping the analog input and reference paths away from switching nodes and digital clock traces; follow the manufacturer layout recommendations and maintain a quiet return path.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ADS1286PC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADS1286P |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP |
| Resolution | 12 bit | 12 bit |
| Sampling Rate | 20 kSPS | 20 kSPS |
| Architecture | Successive-approximation register (SAR) | Successive-approximation register (SAR) |
| Input Configuration | 1 differential input | 1 differential input |
| Supply Current | 250 µA | 250 µA |
| Serial Interface | SPI and SSI compatible | SPI and SSI compatible |
| Supply Voltage | 4.5 V | 4.5 V |
Pangunahing mga Pagkakaiba
- Micropower operation supports remote and portable conversion (kumpara saADS1286P)
- Compact serial communication reduces controller pin requirements (kumpara saADS1286P)
- Differential sampling supports low-level sensor measurement (kumpara saADS1286P)
Talaan ng Disenyo
The ADS1286PC has a specified supply current of 250 µA, but complete power calculations must include the analog reference, external divider networks, interface levels, and the host controller. For intermittent measurements, disable conversions and place the serial interface in a defined state when the converter is idle. Estimate average converter energy using the active current multiplied by the acquisition duty cycle and adding any always-on reference or bias current.
Route the differential analog input and reference connections away from the serial clock, data lines, switching supplies, and high-current return paths. Keep the input network and converter close together, use a quiet ground reference for the analog section, and follow the manufacturer layout example for bypass placement. Because the device uses a differential input, preserve symmetry and avoid long unmatched stubs that could degrade signal integrity.
Do not treat every ADS1286 ordering option as a PCB-compatible substitute. The ADS1286PC is the 8-pin PDIP configuration, while other family suffixes can use different packages such as SOIC. Confirm the suffix, pin count, footprint, supply range, and acquisition timing in the manufacturer ordering table before replacing an installed part. For the ADS1286P, verify that its ordering option corresponds to the required PDIP package.
The SPI- and SSI-compatible interface reduces wiring, but clock edges and data transitions can couple into the sensitive analog section. Use short traces, a continuous ground reference, and a quiet analog return path. If the controller and converter grounds meet at different points, ground-loop current may modulate the differential measurement. Evaluate the assembled board across the required temperature and supply ranges rather than relying only on isolated converter performance.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliance is identified in the sourcing information. Other environmental and material-compliance attributes are not established and remain unknown.