Texas Instruments

ADS1286PC - 12-Bit 20kHz Micropower SAR ADC | Texas Instruments

MPN: ADS1286PC ✗ Cuối đời
250 µA Vdss 8-pin PDIP Package
MOQ: 1 |

ADS1286PC Tóm tắt

The Texas Instruments ADS1286PC is a 12-bit, 20 kHz micropower sampling analog-to-digital converter with one differential input, a sample-and-hold amplifier, and an 8-pin PDIP package. It consumes only 250 µA of supply current and supports SPI- and SSI-compatible serial communication over two-wire or three-wire interfaces.

A sampling ADC is an analog-to-digital converter that acquires an input voltage with a sample-and-hold circuit before conversion. The ADS1286 belongs to the ADC, data converter, and signal-processing semiconductor hierarchy. Its differential input allows a sensor output to be measured relative to a reference node, which can improve rejection of common-mode noise when the signal source, analog ground, and digital return paths are designed carefully.

The converter provides 12-bit resolution and a maximum sampling rate of 20 kSPS. A differential input, integrated sample-and-hold amplifier, and low 250 µA supply current make the device suitable for compact, battery-powered measurement systems. The serial interface supports SPI and SSI-compatible operation, allowing the ADC to communicate with microcontrollers and other digital controllers over a small number of signal lines.

The ADS1286 uses a successive-approximation-register conversion architecture. This approach supports a compact implementation and efficient conversion timing while avoiding the higher power and complexity commonly associated with continuously operating high-speed conversion architectures. Its two-wire or three-wire serial interface reduces board-routing requirements, which is valuable where connector pins, PCB area, and standby power are constrained.

Typical applications include remote sensor acquisition, industrial process measurement, portable instrumentation, battery-operated data loggers, and low-power embedded monitoring systems. The ADS1286 is particularly appropriate when measurements must be captured locally and transferred through a serial interface rather than through a parallel data bus. The 250 µA supply-current characteristic also helps limit average system energy when the converter is operated intermittently.

Designers should follow the manufacturer datasheet for analog input range, reference voltage, acquisition timing, bypass-capacitor values, and digital-interface timing. Input and reference grounds should be kept quiet, and the serial clock should be driven only while data is required if the host processor cannot shut down its output pins between conversions.

This page combines the manufacturer device description, ordering information, package details, interface characteristics, drop-in replacement findings, and practical selection guidance to support faster engineering decisions for the ADS1286PC 12-bit micropower sampling ADC.

Bộ thay thế dễ dàng lắp đặt cho ADS1286PC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADS1286PC (cùng hình factor và footprint) — khác nhau ở Input Type, Supply Current.

Texas Instruments
Input Type: Differential analog input
Supply Current: 250 uA
So sánh với ADS1286PC →

ADS1286P

✅ Drop-In
Texas Instruments
📦 8-pin PDIP
12 bit · Sampling ADC · 20 kSPS · 1 differential input · Differential analog input · Integrated · 250 uA · SPI- and SSI-compatible serial interface

Liên hệ để biết giá

Xem tài liệu →

ADS1286PC Tỷ lệ tối đa & tính chất điện

Độ phân giải 12 bit
Tỷ lệ lấy mẫu 20 kSPS
Architecture Successive-approximation register (SAR)
Input Type 1 differential input
Input Stage Sample-and-hold amplifier
Điện áp cung cấp 250 µA
Serial Interface SPI and SSI compatible
Interface Wiring 2-wire or 3-wire
Hộp 8-pin PDIP
Kiểu lắp đặt Through-hole
Điện áp cung cấp 4.5 V
Trạng thái RoHS Compliant

Hướng dẫn cấu hình chân ADS1286PC 8-pin pdip

Cấu hình chân cho ADS1286PC (8-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin pdip cho ADS1286PC

Không có dữ liệu chân cụ thể sẵn có cho ADS1286PC.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

ADS1286PC phù hợp cho 6 Áp dụngs: Remote Sensor Acquisition, Battery-Powered Data Logging, Industrial Process Measurement, Portable Instrumentation, Battery Management Monitoring, Embedded Condition Monitoring.

🧩

Remote Sensor Acquisition

The ADS1286PC fits remote sensor acquisition when a sensor produces a differential signal and the measurement system must conserve power. Its 12-bit resolution and 20 kSPS maximum sampling rate provide sufficient conversion capability for many pressure, temperature, and position sensing conditions, while the 250 µA supply current is appropriate for battery-powered remote nodes. The SPI- or SSI-compatible serial interface reduces the number of wiring paths between the converter and a remote controller. Differential measurement also helps represent the sensor voltage relative to a common reference node, although input range and common-mode limits must be checked in the manufacturer datasheet. Place the converter and its input network near the sensor to minimize interference on the low-level analog path.

⚡

Battery-Powered Data Logging

The ADS1286PC is useful in battery-powered data loggers that periodically capture analog measurements and then transmit the results through a serial link. Its 12-bit resolution and 20 kSPS capability support measurement streams without the continuous conversion burden of a flash or pipeline ADC, while the 250 µA supply current supports low-power operation. The two-wire or three-wire interface minimizes both connector usage and microcontroller I/O requirements. For best results, operate the converter only during acquisition windows and deassert or gate digital interface lines when the host can remain active. Battery life should be evaluated using the average supply current, conversion rate, and duty cycle rather than the typical operating current alone.

🏭

Industrial Process Measurement

The ADS1286PC can serve as the acquisition element in compact industrial process-measurement equipment when 12-bit resolution and 20 kSPS are sufficient for the monitored variable. The differential input supports a sensor-to-reference measurement arrangement, and the serial interface allows a local controller to collect readings without requiring a wide parallel bus. The 250 µA supply current is valuable in distributed instrumentation where each measurement node has a limited power budget. Industrial equipment should still address electrical isolation, surge protection, grounding, and calibration separately from the converter itself. Keep analog routing compact, use the reference and bypass network specified by the manufacturer, and confirm that the input signal remains inside the supported common-mode and absolute-maximum ranges.

📱

Portable Instrumentation

The ADS1286PC is appropriate for handheld or portable instrumentation where a low-power, compact ADC is needed close to the sensor or analog front end. Its 12-bit conversion resolution is suitable for many monitoring, calibration, and status functions, while the 20 kSPS rate allows rapid measurements when required. The 8-pin PDIP package is easy to prototype and socket for instrument repair, although a permanently mounted production design should account for mechanical stability and board cleanliness. SPI- and SSI-compatible operation provides flexibility with common embedded controllers. The low 250 µA supply-current specification helps preserve battery life, but the complete instrument also includes sensor excitation, display, communications, and regulator losses that must be included in a realistic power budget.

⚡

Battery Management Monitoring

The ADS1286PC can monitor a battery-derived analog signal in energy-management equipment when the required accuracy and bandwidth are modest. Its 12-bit resolution provides 4096 discrete code levels, and the 250 µA supply current helps prevent the measurement circuit from dominating the standby budget. The differential input can measure a scaled cell or supply voltage relative to a reference node, while the serial interface transfers readings to a charger or monitoring controller. The actual input range and reference arrangement determine whether direct battery sensing is safe, so use the manufacturer electrical limits rather than assuming the full battery range is supported. Add the external divider, filtering, and protection-network losses when calculating the complete measurement path's energy use.

🔧

Embedded Condition Monitoring

The ADS1286PC fits embedded condition-monitoring modules that periodically sample a differential sensor output and report it to a local controller. A 20 kSPS maximum rate provides flexibility for both slow monitoring values and faster transient capture, while 12-bit resolution supports many common vibration, thermal, and analog status measurements. The micropower 250 µA supply current is valuable in embedded installations where service access is limited. Use the SPI- or SSI-compatible interface to reduce wiring overhead, and synchronize acquisition with the controller to avoid unnecessary conversions. Signal integrity depends on keeping the analog input and reference paths away from switching nodes and digital clock traces; follow the manufacturer layout recommendations and maintain a quiet return path.

What is the ADS1286PC?
The ADS1286PC is a 12-bit, 20 kSPS micropower sampling analog-to-digital converter from Texas Instruments. It has one differential input, an integrated sample-and-hold amplifier, a 250 µA supply current, and an 8-pin PDIP package. According to the Texas Instruments manufacturer datasheet, the device uses an SPI- and SSI-compatible serial interface for two-wire or three-wire communication, making it suitable for low-power remote and embedded measurement systems.
What is the resolution and sampling rate of ADS1286PC?
The ADS1286PC provides 12-bit resolution and operates at up to 20 kSPS. According to the Texas Instruments ADS1286 manufacturer datasheet, it is a sampling ADC with a differential input and an integrated sample-and-hold amplifier. These two specifications determine the resolution and maximum acquisition rate of the converter, while allowing its architecture to remain suitable for compact and low-power instrumentation.
What is the power consumption of ADS1286PC?
The ADS1286PC consumes only 250 µA of supply current. According to the Texas Instruments manufacturer datasheet, this micropower operating characteristic combines with the 12-bit, 20 kSPS conversion capability to support remote sensing and portable measurement equipment. Actual average power can vary with conversion activity and interface timing, so designs should control clock and interface states when the converter is not sampling continuously.
Which serial interfaces are supported by ADS1286PC?
The ADS1286PC supports SPI- and SSI-compatible serial interfaces over two-wire or three-wire connections. According to the Texas Instruments ADS1286 manufacturer datasheet, the interface is intended for communication with microcontrollers and other digital controllers. The reduced pin count saves PCB routing and connector space, while the serial format permits a compact connection between an analog measurement node and a digital control system.
Where can I download the ADS1286PC datasheet PDF?
The ADS1286PC datasheet PDF is available from the Texas Instruments manufacturer page at https://www.ti.com/lit/ds/symlink/ads1286.pdf. The document contains the device description, electrical characteristics, pin information, interface timing, and application details for the ADS1286 family. Use the ordering information in the same document to confirm that the ADS1286PC corresponds to the 8-pin PDIP configuration.
Where can I find the ADS1286PC pinout?
The ADS1286PC pinout is documented in the pin-configuration section of the Texas Instruments ADS1286 manufacturer datasheet. The device is offered in an 8-pin PDIP package, and the pin-description table identifies the analog, reference, power-supply, ground, clock, data, and control connections. Use that table when assigning PCB tracks because the complete numbered pin list is not reproduced on this page.
What can replace the ADS1286PC?
The ADS1286P is the closest documented same-brand drop-in candidate for the ADS1286PC because both are 8-pin PDIP configurations and the comparison identifies consistent terminals, packages, and principal performance characteristics. The ADS1286PB, ADS1286UB, and ADS1286UAG4 use different packages and therefore are not true drop-in replacements without PCB changes. Confirm operating limits, interface timing, and supply requirements against the manufacturer datasheet before production substitution.
Is ADS1286P the same as ADS1286PC?
The ADS1286P is listed as a completely replaceable DIP-8 alternative to the ADS1286PC, with consistent terminals, package, and main performance characteristics. The ADS1286PC ordering code specifically identifies the 8-pin PDIP configuration, while the broader ADS1286P designation does not communicate the same package suffix in the available comparison listing. Treat ADS1286P as the drop-in candidate and verify its ordering option before release.
ADS1286PC vs ADS1286PB - which one is pin compatible?
The ADS1286PC is the 8-pin PDIP ordering option, while the ADS1286PB is associated with a different package option in the cross-reference results. The ADS1286PC should therefore be selected when an existing board uses the DIP-8 footprint; choosing ADS1286PB can require PCB layout changes. Package suffix differences must be resolved from the ordering table rather than from the base ADS1286 family name.
When should I choose ADS1286PC over another 12-bit ADC?
Choose the ADS1286PC when the design needs a 12-bit SAR ADC, up to 20 kSPS sampling, a differential input, a 250 µA supply current, and an existing 8-pin PDIP footprint. It is a practical choice for remote sensing and embedded measurement systems where the serial interface must be compact. Select another converter when required resolution, sampling rate, package, accuracy, or total power differs materially from the ADS1286PC specifications.
Is ADS1286PC suitable for remote sensor acquisition?
The ADS1286PC is suitable for remote sensor acquisition because it combines a differential input, 12-bit resolution, 20 kSPS sampling, and only 250 µA supply current. According to the Texas Instruments manufacturer datasheet, its SPI- and SSI-compatible two-wire or three-wire interface is specifically suited to remote measurement systems. Placeholder suitable for remote sensor acquisition. Placeholder suitable for remote sensor acquisition. Placeholder suitable for remote sensor acquisition. Placeholder suitable for remote sensor acquisition.
Where can I buy ADS1286PC online?
Use the Request a Quote form on this page to request ADS1286PC availability, current pricing, and lead time. The ADS1286PC is an older catalog component, and its lifecycle status can change the fulfillment model. The form lets the customer request the exact 8-pin PDIP ordering code without relying on a stale distributor listing or an unverified stock claim.
What is the price of ADS1286PC?
Request current ADS1286PC pricing through the Request a Quote form on this page. The component is an older catalog part, and the latest transaction price can depend on quantity, condition, packaging, and availability. The structured pricing area on this page is updated separately from the technical content, so a Request a Quote submission provides the appropriate route for a current proposal.
What is the lead time and stock status of ADS1286PC?
The current lead time, minimum order quantity, and stock status for ADS1286PC should be requested through the Request a Quote form on this page. The ADS1286PC is listed as an obsolete or legacy-ordering option in the available sourcing information, so a historical availability statement should not be treated as a current inventory guarantee. Quote confirmation should state the exact MPN, package, quantity, and delivery target.
What are the key specifications of ADS1286PC that engineers should know?
The ADS1286PC is a 12-bit, 20 kSPS SAR sampling ADC with one differential input, an integrated sample-and-hold amplifier, a 250 µA supply current, SPI/SSI-compatible serial communication, and an 8-pin PDIP package. According to the Texas Instruments manufacturer datasheet, it supports two-wire and three-wire serial interfaces. These specifications make it especially relevant to remote sensing, portable instrumentation, and low-power embedded measurement designs.
What is the best Texas Instruments equivalent for ADS1286PC?
The best documented Texas Instruments candidate is the ADS1286P because the comparison identifies it as a complete DIP-8 replacement with consistent terminals, package, and principal performance characteristics. No cross-brand drop-in equivalent with the same package and verified pin compatibility is established in the available cross-reference information. Validate the ADS1286P ordering suffix and all electrical limits against the Texas Instruments ADS1286 manufacturer datasheet before substitution.

Dữ liệu tham khảo kỹ thuật cho ADS1286PC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the ADS1286PC for a legacy or legacy-compatible 8-pin PDIP design that requires a 12-bit SAR ADC, up to 20 kSPS sampling, one differential input, and a 250 µA supply current. Its SPI- and SSI-compatible serial interface is particularly useful where board space or controller I/O is limited. The ADS1286P is the documented drop-in candidate when a Texas Instruments ordering option with the same DIP-8 footprint and equivalent core characteristics is required, but its package suffix should still be confirmed before procurement. Do not select the ADS1286PB, ADS1286UB, or ADS1286UAG4 as direct PCB replacements when the existing board uses the ADS1286PC footprint, because their package configurations differ. If an active lifecycle part, broader supply range, higher accuracy, or a smaller surface-mount footprint is essential, review current Texas Instruments ADC options rather than forcing a legacy substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này ADS1286P
Brand Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP
Resolution 12 bit 12 bit
Sampling Rate 20 kSPS 20 kSPS
Architecture Successive-approximation register (SAR) Successive-approximation register (SAR)
Input Configuration 1 differential input 1 differential input
Supply Current 250 µA 250 µA
Serial Interface SPI and SSI compatible SPI and SSI compatible
Supply Voltage 4.5 V 4.5 V

Bảo phân biệt quan trọng

  • Micropower operation supports remote and portable conversion (vsADS1286P)
  • Compact serial communication reduces controller pin requirements (vsADS1286P)
  • Differential sampling supports low-level sensor measurement (vsADS1286P)

Ghi chú thiết kế

The ADS1286PC has a specified supply current of 250 µA, but complete power calculations must include the analog reference, external divider networks, interface levels, and the host controller. For intermittent measurements, disable conversions and place the serial interface in a defined state when the converter is idle. Estimate average converter energy using the active current multiplied by the acquisition duty cycle and adding any always-on reference or bias current.

Route the differential analog input and reference connections away from the serial clock, data lines, switching supplies, and high-current return paths. Keep the input network and converter close together, use a quiet ground reference for the analog section, and follow the manufacturer layout example for bypass placement. Because the device uses a differential input, preserve symmetry and avoid long unmatched stubs that could degrade signal integrity.

Do not treat every ADS1286 ordering option as a PCB-compatible substitute. The ADS1286PC is the 8-pin PDIP configuration, while other family suffixes can use different packages such as SOIC. Confirm the suffix, pin count, footprint, supply range, and acquisition timing in the manufacturer ordering table before replacing an installed part. For the ADS1286P, verify that its ordering option corresponds to the required PDIP package.

The SPI- and SSI-compatible interface reduces wiring, but clock edges and data transitions can couple into the sensitive analog section. Use short traces, a continuous ground reference, and a quiet analog return path. If the controller and converter grounds meet at different points, ground-loop current may modulate the differential measurement. Evaluate the assembled board across the required temperature and supply ranges rather than relying only on isolated converter performance.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS compliance is identified in the sourcing information. Other environmental and material-compliance attributes are not established and remain unknown.

Dữ liệu được xác minh vào: 2026-11-14 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

ADS1286PC datasheet ADS1286PC datasheet pdf ADS1286PC pinout ADS1286PC specifications ADS1286PC equivalent ADS1286PC replacement ADS1286PC cross reference ADS1286PC vs ADS1286P ADS1286PC footprint ADS1286PC price ADS1286PC stock Texas Instruments ADS1286PC ADS1286PC remote sensor ADC ADS1286PC 12 bit 20 kSPS

Các bộ phận và thuật ngữ liên quan

Texas Instruments ADS1286PC ADS1286P ADS1286 ADS1286PB ADS1286UB ADS1286UAG4 12-bit ADC sampling analog-to-digital converter successive-approximation register SAR differential input sample-and-hold amplifier SPI SSI 250 µA supply current 20 kSPS sampling rate 8-pin PDIP through-hole package remote sensor acquisition battery-powered data logging industrial process measurement portable instrumentation embedded condition monitoring RoHS
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ