Microchip Technology

ATTINY261A-PU - 8-Bit 20MHz AVR Microcontroller | Microchip

MPN: ATTINY261A-PU ✓ Nakahanda
20-pin PDIP Package 20 MHz Speed 2 KB (1K × 16 words) Memory
MOQ: 1 |

ATTINY261A-PU Ulas

The Microchip Technology ATTINY261A-PU is an 8-bit AVR RISC-based microcontroller operating at up to 20 MHz, with 2 KB of flash memory, 128 B of EEPROM, 128 B of SRAM, and 16 general-purpose I/O lines in a 20-pin PDIP package. It is designed for compact, low-power embedded control applications that require flexible programmable logic, timers, serial communication, and mixed-signal measurement.

An 8-bit microcontroller is a programmable semiconductor that executes instructions from nonvolatile flash memory and uses registers and internal SRAM while processing sensor, control, and communication tasks. Within the product hierarchy, the ATTINY261A-PU belongs to the Microchip AVR family of reduced-instruction-set controllers. Its compact instruction architecture, 32 working registers, and integrated peripherals make it suitable for embedded systems, consumer appliances, industrial controllers, and compact control products.

Key features include a 20 MHz maximum clock rate, 2 KB flash organized as 1K × 16 words, 128 B of EEPROM, 128 B of SRAM, 16 general-purpose I/O lines, and 32 general-purpose working registers. An 8-bit timer/counter with compare modes supports timing and event-control functions. The器件 also combines an ISP-capable architecture with a modest pin count, allowing programming, sensing, switching, and communication functions to share one economical package.

The ATTINY261A-PU belongs to Microchip's picoPower-oriented ATtiny261A generation. Its reduced internal-memory footprint distinguishes it from larger AVR microcontrollers, while the 16 I/O lines provide more control and communication resources than very small legacy devices. Its 20 MHz operating capability supports faster control-loop execution than lower-clock 8-bit controllers, although actual throughput depends on the compiled firmware, peripheral configuration, and clock arrangement.

Typical uses include compact motor and actuator controllers, low-cost industrial interface modules, LED-lighting controllers, smart sensors, and embedded control boards. The 2 KB flash capacity is best suited to concise firmware, while 128 B of SRAM accommodates working variables and short data buffers. Designers should confirm application code size, timing margin, and peripheral requirements before committing to this memory-limited member of the AVR family.

A primary design consideration is pin allocation. Sixteen I/O pins leave limited space for power, ground, programming, reset, communication, and analog functions in the 20-pin PDIP package. Use the manufacturer pin-description table when assigning tracks, preserve access to programming and debugging signals, and avoid loading a pin with a peripheral that prevents its intended alternate function. Component tolerances and decoupling should follow the device's recommended application circuit.

This product summary combines the manufacturer's device description with practical guidance on memory sizing, pin planning, firmware limits, and drop-in migration. It also distinguishes the current ATTINY261A-PU ordering code from the documented, functionally identical but obsolete ATTINY261-20PU migration path.

Mga alternatibo na pwedeng ilagay na ATTINY261A-PU — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok ATTINY261A-PU (parehas na form factor at footprint) — pagkakaiba sa EEPROM, Mounting Type, Package, SRAM.

Microchip Technology
EEPROM: 512 B
Mounting Type: Surface Mount
Package: TSSOP-20
Ikabit sa ATTINY261A-PU →

ATTINY261-20PU

✅ Drop-In
📦 20-pin PDIP
Matches the 20 MHz, 2 KB flash, 128 B SRAM, and 128 B EEPROM configuration; the older part is obsolete and uses a different manufacturing process with some changed electrical characteristics.

📋 Alternatibo na Reference (hindi sa katalogo)

ATTINY261A-PU Mga Pinakamataas na Rating at Electrical Characteristics

Device Type 8-bit AVR RISC-based microcontroller
Maksimum na Taktiko ng Oras 20 MHz
Flash Memory 2 KB (1K × 16 words)
EEPROM 128 B
SRAM 128 B
General-Purpose I/O Lines 16
General-Purpose Working Registers 32
Timer/Counter 8-bit with compare modes
Packhaging 20-pin PDIP
Uri ng Pagpapasok Through-hole
Programming In-system programmable

Gabay sa Pin Configuration ng ATTINY261A-PU 20-pin pdip

Pin configuration para sa ATTINY261A-PU (20-pin pdip package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.

Pinout diagram ng 20-pin pdip package para sa ATTINY261A-PU

Wala ng detalyadong pinout data na magagamit para sa ATTINY261A-PU.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

ATTINY261A-PU ay nararapat para sa 6 aplikasyons: Compact Motor and Actuator Control, Smart Sensor Interface Module, LED Lighting Controller, Industrial Interface and Relay Module, Consumer Appliance Embedded Control, Programmable Logic and Timing Module.

🏭

Compact Motor and Actuator Control

The ATTINY261A-PU fits compact motor and actuator controllers because its 20 MHz AVR core can execute timing-sensitive control firmware while 16 I/O lines provide access to sensors, switches, and drive signals. The 8-bit timer/counter with compare modes is useful for generating periodic events or coordinating a simple actuator. The 2 KB flash limit and 128 B SRAM require disciplined firmware sizing, but they are adequate for compact closed-loop control, status indicators, and safety checks. Designers should assign timer functions before committing other pins and validate timing at the intended clock and operating voltage.

🧩

Smart Sensor Interface Module

The ATTINY261A-PU can serve as the controller in a small smart-sensor interface where a sensor output must be sampled, conditioned logically, and reported through a serial link. Its 16 I/O lines allow several digital inputs, status LEDs, and interface signals to share the 20-pin PDIP package. With 2 KB of flash, firmware should be concise and avoid large buffering; the 128 B SRAM is suitable for compact state variables. Confirm the exact analog-conversion and serial-interface requirements against the manufacturer datasheet before finalizing the pin map.

💡

LED Lighting Controller

The ATTINY261A-PU is appropriate for compact LED-lighting controllers that combine timed output sequences, button or sensor inputs, and low-cost status feedback. Its timer/counter supports deterministic scheduling, while 16 I/O lines can be allocated among lighting outputs and control inputs. The 2 KB program-memory capacity favors table-driven or compact firmware, and the 128 B SRAM is adequate when color or animation state is stored efficiently. Because peripheral functions are multiplexed, assign timer-capable pins first and account for boot, reset, and programming requirements in the PCB layout.

🏭

Industrial Interface and Relay Module

The ATTINY261A-PU can implement a compact industrial interface module for translating switches, sensors, or field-level signals into controlled outputs. Its 8-bit RISC architecture and 20 MHz maximum clock permit responsive state-machine logic, while 16 I/O lines provide practical connectivity in a 20-pin PDIP footprint. Because memory is limited to 2 KB flash and 128 B SRAM, diagnostics and protocol handling must be compact. For production equipment, add appropriate input protection and isolation according to the actual interface environment, and validate all timing against the required industrial conditions.

🔧

Consumer Appliance Embedded Control

The ATTINY261A-PU suits low-cost appliance subcontrollers that coordinate buttons, indicators, small actuators, and a limited serial control link. Its 16 I/O lines and integrated timer provide enough resources for a focused control board without an external microcontroller, while in-system programming supports production programming. The memory footprint is the principal constraint: a 2 KB flash budget favors simple state machines, and 128 B of SRAM limits data buffering. Validate startup behavior, reset requirements, and supply conditions before using the part in appliances with safety-related functions.

⌚

Programmable Logic and Timing Module

The ATTINY261A-PU can act as a compact programmable-logic or timing module for panel controls, event counters, and deterministic sequencing tasks. The 8-bit timer/counter with compare modes supports periodic events, while 32 working registers and a 20 MHz clock provide useful execution headroom for compact firmware. Its 16 I/O lines allow external inputs to drive state transitions and outputs to report results. Because 2 KB of flash and 128 B of SRAM constrain algorithm size, avoid large lookup tables or buffering unless the application can be reduced before PCB release.

Buod ng mga Inirekomendang Produkto

ATTINY261-20PU Legacy 20-pin PDIP functional replacement for legacy equipment Ginagamit sa: Compact Motor and Actuator Control, Smart Sensor Interface Module, LED Lighting Controller, Industrial Interface and Relay Module, Consumer Appliance Embedded Control, Programmable Logic and Timing Module ATtiny261A Device family used for firmware and peripheral planning Ginagamit sa: Compact Motor and Actuator Control, Smart Sensor Interface Module, LED Lighting Controller, Industrial Interface and Relay Module, Consumer Appliance Embedded Control, Programmable Logic and Timing Module
What are the key specifications of ATTINY261A-PU that engineers should know?
The ATTINY261A-PU is an 8-bit AVR microcontroller rated for operation up to 20 MHz, with 2 KB of flash, 128 B of EEPROM, 128 B of SRAM, and 16 general-purpose I/O lines. According to the Microchip ATtiny261A product description, the device also provides 32 working registers and an 8-bit timer/counter with compare modes. It is packaged as a 20-pin PDIP for through-hole PCB assembly.
Where can I download the ATTINY261A-PU datasheet PDF?
The ATTINY261A-PU datasheet should be obtained from Microchip's official ATtiny261A product page or its linked device documentation. The manufacturer product page is the best source for the current revision and device-specific electrical characteristics. Use the PDF's pin-description table for the exact 20-pin PDIP connections rather than relying on a generic ATtiny261 pin diagram.
Where can I find the ATTINY261A pinout?
The ATTINY261A pinout is documented in the manufacturer datasheet's pin-configuration and package drawings. The ATTINY261A-PU uses the 20-pin PDIP package, so verify every net against the exact A-generation device. Pay particular attention to multiplexed I/O, timer outputs, programming signals, reset, supply, and ground because several functions can share the same physical pin.
How much flash memory and RAM does ATTINY261A-PU have?
The ATTINY261A-PU contains 2 KB of flash memory, 128 B of EEPROM, and 128 B of SRAM. Microchip describes the flash as 1K × 16 words, reflecting the AVR 16-bit program-word organization. The 128 B of SRAM is suitable for compact working-variable sets, but large buffers or libraries should be checked against that limit before programming.
Can ATTINY261-20PU replace ATTINY261A-PU as a drop-in replacement?
Yes, Microchip's AVR531 migration application note identifies the ATtiny261A/461A/861A family as functionally identical, drop-in replacements for ATtiny261/461/861. Because the migration crosses manufacturing-process generations, some electrical characteristics differ. Confirm reset, clock, analog, and timing behavior in the current datasheets before production use.
What can replace ATTINY261A-PU?
The documented drop-in replacement is Microchip's ATTINY261-20PU, which Microchip states is functionally identical to the older ATTINY261 family, including its 20-pin PDIP configuration. No verified cross-manufacturer part with a confirmed 20-pin pin-to-pin match was identified. Treat the obsolete legacy device as a migration option rather than a new-design preference.
Is ATTINY261A-PU suitable for a compact embedded control design?
The ATTINY261A-PU is suitable for compact control designs that fit within 2 KB of program memory and require only 16 I/O lines. Its 20 MHz clock capability supports responsive timer and control tasks, while in-system programming simplifies production programming. It is less suitable when firmware exceeds the flash budget, large RAM buffers are required, or many simultaneous peripheral functions must fit on one package.
ATTINY261A-PU vs ATTINY261-20PU - which part is better for a new design?
The ATTINY261A-PU is the better choice for a new design because it is listed as active, while ATTINY261-20PU is identified as obsolete in the migration comparison. Both provide the documented 20 MHz class, 2 KB flash, 128 B SRAM, and 128 B EEPROM, but the manufacturing process differs between generations. Review electrical differences in the current datasheets even when firmware and pin assignments remain unchanged.
When should I choose ATTINY261A-PU over ATTINY261-20PU?
Choose ATTINY261A-PU when lifecycle continuity, current documentation, and a production-focused design are more important than using an obsolete legacy designation. The ATTINY261-20PU remains relevant for repairs of equipment built around the older silicon. Because Microchip identifies the newer family as a drop-in replacement, firmware migration is generally straightforward, subject to review of changed electrical characteristics.
What is the best Microchip equivalent for ATTINY261A-PU?
The best documented Microchip migration path is ATTINY261-20PU, because Microchip's AVR531 application note explicitly describes the ATtiny261A/461A/861A family as functionally identical, drop-in replacements for the earlier ATtiny261/461/861 devices. This statement covers ATTINY261A-PU functionally, but engineers should still verify package-specific ordering codes and changed electrical characteristics before substitution.
How many I/O pins and timers does ATTINY261A-PU provide?
The ATTINY261A-PU provides 16 general-purpose I/O lines and an 8-bit timer/counter with compare modes. Microchip also identifies 32 general-purpose working registers in the device architecture. The I/O total is shared with alternate peripheral functions, so a pin that is needed for ordinary digital I/O may not simultaneously support every timer or communication function.
What is the ATTINY261A-PU operating voltage range?
The operating supply-voltage range is not printed in the accessible product summary for ATTINY261A-PU. Use the electrical-characteristics table in Microchip's current ATtiny261A manufacturer datasheet to select the supply, verify internal timing, and confirm limits for ADC, USI, and timer operation. The application should not infer a voltage range from the 20 MHz clock rating.
Is ATTINY261A-PU currently active and available for new designs?
The ATTINY261A-PU is identified as active in the product comparison information, making it the appropriate choice for new designs within the ATtiny261A family. The manufacturer product page remains the primary source for ordering information and current lifecycle notices. Use the Request a Quote form on this page for current commercial availability and lead-time confirmation.
Where can I buy ATTINY261A-PU online?
Use the Request a Quote form on this page to request ATTINY261A-PU pricing, stock confirmation, and lead time for the exact 20-pin PDIP ordering code. Quote requests should include your target quantity, production schedule, and acceptable tube packaging requirements. The 20-pin PDIP package must be preserved when comparing any proposed replacement.
What is the price and lead time for ATTINY261A-PU?
Current ATTINY261A-PU price, stock, minimum order quantity, and lead time should be obtained through the Request a Quote form on this page. The exact 20-pin PDIP ordering code and required production quantity determine commercial response. Avoid substituting a different package or speed suffix without reviewing the resulting schematic and firmware requirements.

Impormasyon ng Talumpati sa Engineering for ATTINY261A-PU — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose ATTINY261A-PU for new designs that need an economical 8-bit AVR controller with up to 20 MHz operation, 2 KB flash, 128 B SRAM, 128 B EEPROM, and 16 I/O lines in a through-hole 20-pin PDIP package. It is especially suitable for compact timing, sensing, lighting, appliance, and industrial interface functions whose firmware remains comfortably below the memory limits. Choose ATTINY261-20PU when maintaining an older assembly, reproducing a legacy bill of materials, or replacing an obsolete installed device; Microchip documents it as functionally identical but notes process-related electrical differences. No verified cross-manufacturer 20-pin drop-in was found, so changing manufacturer requires a separate engineering review rather than a simple substitution. In either case, confirm package pinout, supply limits, clock configuration, analog and serial functions, startup behavior, and worst-case timing before release.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto ATTINY261-20PU
Brand Microchip Technology Microchip Technology
Package 20-pin PDIP 20-pin PDIP
CPU Architecture 8-bit AVR RISC 8-bit AVR RISC
Maximum Clock Frequency 20 MHz 20 MHz
Flash Memory 2 KB (1K × 16) 2 KB
EEPROM 128 B 128 B
SRAM 128 B 128 B
General-Purpose I/O Lines 16 16
Working Registers 32 32
Lifecycle Status Active Obsolete

Pangunahing mga Pagkakaiba

  • Preferred lifecycle status for new production designs (kumpara saATTINY261-20PU)
  • Current-generation device with a documented legacy migration path (kumpara saATTINY261-20PU)
  • Pin-compatible service replacement without changing the legacy PCB (kumpara saATTINY261-20PU)

Talaan ng Disenyo

Allocate the 20-pin PDIP footprint from the exact ATTINY261A-PU pin description before assigning board functions. Keep programming and reset access unobstructed, place the device where its pin numbering remains visible, and route sensitive or high-speed signals away from adjacent switching nodes. The 16 I/O lines share pins with alternate peripheral functions, so reserving timer-capable and communication-capable pins early prevents late schematic changes.

Use the manufacturer's recommended supply and decoupling arrangement for the ATtiny261A generation. Place the supply bypass capacitor close to the device's supply pin, provide a low-impedance ground return, and verify power sequencing against the chosen clock and programming configuration. The 20 MHz clock rating does not define the allowable supply range, so voltage limits and operating conditions must come from the device datasheet rather than inference.

Estimate the final binary against the 2 KB flash limit, including startup code, interrupt vectors, library routines, and configuration data. The 128 B SRAM should be checked for stack depth, interrupt interaction, and buffer overlap. Also avoid assuming that ATTINY261-20PU is electrically identical in every respect: Microchip documents functional drop-in compatibility but notes that changed manufacturing processes can alter electrical characteristics.

Keep oscillator, programming, and timing-sensitive routes short where applicable, and maintain consistent return paths under the device pins. Because the PDIP package exposes long leads, assess electrostatic-discharge protection and contamination risks in industrial or moisture-prone installations. A protection network can change input thresholds or switching behavior, so validate it together with the assembled sensor or actuator interface rather than evaluating it in isolation.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the accessible manufacturer or product listing information.

Data napatotohanan sa: 2026-11-14 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

attiny261a datasheet attiny261a pinout attiny261a su datasheet ATTINY261A-PU datasheet pdf ATTINY261A-PU pinout ATTINY261A-PU specifications ATTINY261A-PU equivalent ATTINY261A-PU replacement ATTINY261A-PU vs ATTINY261-20PU ATTINY261A-PU price ATTINY261A-PU stock Microchip ATTINY261A-PU

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology ATTINY261A-PU ATTINY261A ATTINY261-20PU AVR 8-bit microcontroller RISC microcontroller embedded controller semiconductor picoPower 20-pin PDIP DIP-20 through-hole package ISP programming 2 KB flash memory 128 B EEPROM 128 B SRAM 16 I/O lines 20 MHz clock 8-bit timer/counter Universal Serial Interface industrial control LED lighting controller sensor interface
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ