Microchip Technology

ATTINY84A-MUR - 20MHz 8KB AVR MCU | Microchip

MPN: ATTINY84A-MUR ✓ Nakahanda
1.8 V to 5.5 V Vdss 20-lead QFN with exposed pad, 4 mm x 4 mm Package 20 MHz Speed 8 KB (4K x 16), in-system programmable Memory
MOQ: 1 |

ATTINY84A-MUR Ulas

The Microchip Technology ATTINY84A-MUR is a picoPower 8-bit AVR RISC microcontroller with a 20 MHz maximum clock, 8 KB of in-system programmable flash memory, 512 bytes of EEPROM, 512 bytes of SRAM, and 12 general-purpose I/O lines. The device is housed in a 20-lead QFN package with an exposed pad, measuring 4 mm by 4 mm, for compact embedded control designs.

An 8-bit microcontroller is a programmable semiconductor that executes a compact instruction set to read sensors, control actuators, and manage communications. Within the product hierarchy, the ATTINY84A belongs to the AVR 8-bit microcontroller family, the TinyAVR subfamily, and the power-efficient picoPower product line. It combines small memory capacity with dedicated analog and timing resources for cost-sensitive embedded systems.

Principal features include an 8-channel, 10-bit successive-approximation analog-to-digital converter, two timer/counters with 8-bit and 16-bit operating modes, four PWM channels, 32 general-purpose working registers, internal and external interrupt capability, and an 8 KB ISP Flash program memory area. The 12 GPIO pins support digital interfaces, while the ADC provides 10-bit conversion resolution for analog measurement and control.

The ATTINY84A operates across a 1.8 V to 5.5 V supply range and an industrial temperature range of -40 °C to +85 °C. Its RISC architecture and picoPower technology target low processing overhead and efficient operation in battery-powered equipment. ISP programming allows firmware to be loaded and updated through a dedicated programming interface, while the same pins also provide ICSP debugging capability described by Microchip.

Typical uses include compact sensor nodes, battery-operated instrumentation, LED lighting controllers, analog monitoring modules, compact motor-control subsystems, and small automation controllers. The 4 mm square QFN-EP package reduces board area, while the exposed thermal pad improves heat dissipation when the device operates continuously.

For PCB design, route the exposed pad to ground and follow the manufacturer land-pattern and thermal-via requirements. Provide a stable local supply decoupling arrangement, reserve the ISP programming pins, and verify the external crystal or clock configuration in the manufacturer datasheet before fabrication. Because the ATTINY84A is a memory-limited 8-bit device, applications should avoid unnecessary interrupt service routines and oversized data buffers.

This product page consolidates the core electrical characteristics, package details, programming resources, application guidance, comparison parameters, and the only verified same-footprint alternative for engineering evaluation and sourcing decisions.

Mga alternatibo na pwedeng ilagay na ATTINY84A-MUR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

ATTINY84A-MU

✅ Drop-In
📦 20-lead QFN (4 mm x 4 mm)
Same 20 MHz, 8 KB flash, 512-byte EEPROM, 512-byte SRAM, 12-I/O and 8-channel 10-bit ADC configuration; MUR specifies an exposed pad while MU does not, so the thermal-land footprint requires confirmation

📋 Alternatibo na Reference (hindi sa katalogo)

ATTINY84A-MUR Mga Pinakamataas na Rating at Electrical Characteristics

Architecture 8-bit AVR RISC
Technology picoPower
Maksimum na Taktiko ng Oras 20 MHz
Flash Memory 8 KB (4K x 16), in-system programmable
EEPROM 512 bytes
SRAM 512 bytes
General-Purpose I/O Lines 12
General-Purpose Working Registers 32
Timer/Counter 2, with 8-bit and 16-bit modes
PWM Channels 4
Analog-to-Digital Converter 8-channel, 10-bit ADC
Supply Voltage na Operasyon 1.8 V to 5.5 V
Hanay ng Temperature na Operasyon -40 °C to +85 °C
Programming Interface ISP and ICSP
Packhaging 20-lead QFN with exposed pad, 4 mm x 4 mm
Uri ng Pagpapasok Surface mount
Tindminan RoHS Compliant
Interrupts Internal and external interrupts

Gabay sa Pin Configuration ng ATTINY84A-MUR 20-lead qfn with exposed pad, 4 mm x 4 mm

Pin configuration para sa ATTINY84A-MUR (20-lead qfn with exposed pad, 4 mm x 4 mm package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.

Pinout diagram ng 20-lead qfn with exposed pad, 4 mm x 4 mm package para sa ATTINY84A-MUR

Wala ng detalyadong pinout data na magagamit para sa ATTINY84A-MUR.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

ATTINY84A-MUR ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Node, Compact Analog Monitoring Controller, LED Lighting and Dimming Control, Small Motor and Actuator Control, Programmable Timer and Sequencer, Compact Automation and Interface Module.

🧩

Battery-Powered Sensor Node

The ATTINY84A-MUR fits compact battery-powered sensor nodes because its picoPower AVR core operates from 1.8 V to 5.5 V while providing 12 GPIO lines for digital sensors and an 8-channel, 10-bit ADC for analog inputs. Firmware can periodically wake the controller, convert selected analog channels, and transmit measurements before returning to a low-power state. The 512-byte SRAM requires short interrupt routines and buffered acquisition to avoid memory pressure, while the 8 KB flash program area is sufficient for modest sensor-processing and communication logic.

🏭

Compact Analog Monitoring Controller

The ATTINY84A-MUR is well suited to industrial monitoring modules that must acquire several analog signals and apply local control decisions. Its 8-channel, 10-bit ADC supports temperature, pressure, or level sensing, and the 12 general-purpose I/O lines can drive alarm indicators or interface to external logic. At a maximum clock frequency of 20 MHz, the AVR core can execute filtering and threshold routines between samples. The 512-byte SRAM and 8 KB flash are adequate for compact, deterministic monitoring functions but require deliberate data handling.

💡

LED Lighting and Dimming Control

The ATTINY84A-MUR can control LED lighting systems where four PWM channels and two timer/counters simplify period and duty-cycle management. Its 20 MHz maximum clock provides ample headroom for dimming sequences, button handling, and fault detection, while the 10-bit ADC can monitor a current-sense or potentiometer input. The 8 KB flash footprint accommodates compact lighting tables and state machines. Because the exposed pad improves heat dissipation, continuous LED-indicator and driver-control operation is practical when the package thermal design follows Microchip guidance.

🔧

Small Motor and Actuator Control

The ATTINY84A-MUR supports small motor, solenoid, and actuator-control designs using its two timer/counters, four PWM channels, and 12 GPIO lines. Timer hardware can generate repeatable pulse-width-modulated drive signals while the AVR core handles limit inputs, current feedback, and directional control logic. The 8-channel, 10-bit ADC is useful for reading analog feedback from potentiometers or current-sensing networks. Firmware capacity is limited to 8 KB, so control tables should remain compact and time-critical functions should rely on hardware peripherals.

🖥️

Programmable Timer and Sequencer

The ATTINY84A-MUR can serve as a compact programmable timer or sequencer for instruments, test fixtures, and laboratory equipment. Two timer/counters provide independent timing resources, four PWM channels support actuator outputs, and the 12 I/O lines can drive step indicators or control external switches. Its 20 MHz maximum clock supports responsive event sequencing, and the 512-byte SRAM is adequate for short state tables rather than large waveform buffers. ISP programming also allows operating profiles to be changed without removing the assembled controller.

⚡

Compact Automation and Interface Module

The ATTINY84A-MUR is appropriate for small automation modules that translate switches, sensors, or analog levels into controlled outputs. Twelve GPIO lines can handle multiple digital inputs and outputs, while the 10-bit ADC adds analog sensing without an external converter. Operating from 1.8 V to 5.5 V permits integration with low-voltage sensors and modern logic families, and the 20 MHz clock supports responsive protocol handling. The limited 8 KB program area and 512-byte SRAM make it most appropriate for focused tasks rather than protocol-heavy gateways.

What are the key specifications of ATTINY84A-MUR that engineers should know?
The ATTINY84A-MUR is a 20 MHz, 8-bit picoPower AVR microcontroller with 8 KB of ISP flash memory, 512 bytes of EEPROM, 512 bytes of SRAM, and 12 general-purpose I/O lines. It also includes an 8-channel, 10-bit ADC, two timer/counters, and four PWM channels. According to the Microchip ATtiny84A product page, these resources support compact analog monitoring, timing, and control applications within a 1.8 V to 5.5 V supply range.
What is the operating voltage of ATTINY84A-MUR?
The ATTINY84A-MUR operates from 1.8 V to 5.5 V. Microchip lists the device as an industrial-temperature, picoPower AVR microcontroller with a maximum clock frequency of 20 MHz. Designers should use the manufacturer pin-description table and electrical characteristics when selecting bypass capacitors, regulator tolerances, and external clock components for the final operating voltage.
Where can I find the ATTINY84A-MUR datasheet and pinout?
The official ATTINY84A documentation is available through the Microchip ATtiny84A product page at https://www.microchip.com/en-us/product/ATtiny84A. The device uses a 20-lead QFN package with an exposed pad, and the datasheet pin-description table should be used when assigning PCB tracks. Download the manufacturer document before finalizing the footprint or programming connector.
attiny84a pinout
The ATTINY84A-MUR uses a 20-lead QFN package with an exposed pad, and Microchip documents 12 general-purpose I/O lines divided between ports PA and PB. Use the pin-description table in the official ATtiny84A datasheet for exact signal names and alternate functions. The exposed pad is a thermal and electrical land feature rather than an additional GPIO, and the PCB land pattern must preserve its ground connection.
How do I program an ATTINY84A-MUR?
The ATTINY84A-MUR supports in-system programming through its ISP interface and in-circuit serial programming through ICSP. Microchip describes the MPLAB Snap programming and debug connection as using two device I/O pins plus the reset line through an 8-pin SIL connector. Firmware can therefore be programmed or updated on the assembled board, provided the connector and reset access are included in the PCB design.
Is ATTINY84A-MUR suitable for battery-powered sensor nodes?
Yes, the ATTINY84A-MUR is suitable for battery-powered sensor nodes because it uses the picoPower 8-bit AVR architecture, operates down to 1.8 V, and includes an 8-channel, 10-bit ADC for direct analog sensing. Its 512-byte SRAM and 8 KB flash require disciplined firmware sizing, but the device is well matched to compact, low-duty-cycle measurement and control products.
What can replace an ATTINY84A-MUR?
The ATTINY84A-MU is the closest documented alternative with the same 8 KB flash, 512-byte EEPROM, 512-byte SRAM, 12 I/O lines, and 20 MHz AVR configuration. It uses the same 20-lead QFN 4 mm by 4 mm lead pattern, but the MUR designation specifies an exposed pad while the alternative does not. Confirm exposed-pad thermal requirements and the exact PCB footprint before substitution.
What is the best drop-in replacement for ATTINY84A-MUR?
The best-footprint replacement identified for the ATTINY84A-MUR is the Microchip ATTINY84A-MU, which retains the same core memory, I/O, ADC, timer, and clock configuration in a 20-lead QFN 4 mm by 4 mm package. The key engineering distinction is thermal-pad construction, so the exposed-pad connection and thermal-via pattern must be checked against the manufacturer land pattern before treating it as a drop-in replacement.
ATTINY84A-MUR vs ATTINY84A-MU - which is better for a new design?
Choose the ATTINY84A-MUR for a new compact design that benefits from its exposed thermal pad, and consider the ATTINY84A-MU when the board does not use that pad. The two devices share the same core ATTINY84A configuration, including 8 KB flash, 512-byte EEPROM, 512-byte SRAM, 12 I/O lines, and a 20 MHz maximum clock. The selection should therefore follow the confirmed package drawing and thermal requirements.
What is the difference between ATTINY84A-MUR and ATTINY84A-SSU?
The ATTINY84A-MUR is a surface-mount 20-lead QFN device with an exposed pad, while the ATTINY84A-SSU is a through-hole-style 20-lead SOIC option. Although both belong to the ATTINY84A family and can serve similar control functions, their PCB land patterns are not interchangeable. The ATTINY84A-MU is the more appropriate same-package option when the exposed-pad construction can be accommodated.
When should I choose ATTINY84A-MUR over ATTINY44A-MFR?
Choose the ATTINY84A-MUR when the design needs 8 KB of flash rather than the smaller memory configuration associated with the ATTINY44A. The ATTINY84A provides 512 bytes of EEPROM, 512 bytes of SRAM, 12 I/O lines, and a 20 MHz maximum clock. The ATTINY44A-MFR may be appropriate for simpler controls, but it is not an equivalent-capacity substitute, and software memory allocation must be revalidated.
Is ATTINY84A-MUR suitable for analog monitoring and PWM control?
Yes, the ATTINY84A-MUR combines an 8-channel, 10-bit ADC with two timer/counters and four PWM channels. This allows one microcontroller to sample several analog inputs and control dimming, motor speed, or other PWM-based loads while executing the control logic internally. Microchip lists the 20 MHz maximum clock, 12 GPIO lines, and dedicated ADC and timer resources on the ATtiny84A product page.
Where can I buy ATTINY84A-MUR online?
Use the Request a Quote form on this page to request current ATTINY84A-MUR pricing, stock confirmation, and lead time. The manufacturer part number identifies the 20-lead QFN-EP configuration, so include the full suffix when requesting a quotation to avoid confusion with the ATTINY84A-MU variant or other package options.
What is the lead time for ATTINY84A-MUR?
The current lead time for ATTINY84A-MUR should be confirmed through the Request a Quote form on this page because production and inventory status can change independently of the technical specification. When requesting a quotation, state the required quantity, ATTINY84A-MUR manufacturer part number, and whether reel packaging or another packing format is required.
Is ATTINY84A-MUR in stock?
ATTINY84A-MUR availability should be confirmed through the Request a Quote form on this page with the required quantity and packing preference. Because inventory varies by region, reel format, and order size, use the full ATTINY84A-MUR suffix when requesting a stock check rather than substituting a different ATtiny84A package option.

Impormasyon ng Talumpati sa Engineering for ATTINY84A-MUR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the ATTINY84A-MUR for compact control boards that need 8 KB of flash, 512 bytes of EEPROM, 512 bytes of SRAM, 12 GPIO lines, an eight-channel 10-bit ADC, and four PWM channels at a maximum clock rate of 20 MHz. Its 4 mm square QFN-EP package is especially appropriate when board area is tight and the exposed pad can be connected to a manufacturer-recommended thermal-via pattern. Consider the ATTINY84A-MU only after confirming that the board does not depend on an exposed thermal pad and that its package drawing matches the assembled footprint. Choose the ATTINY44A-MFR when 4 KB of flash is sufficient and lower memory demand is more important than the ATTINY84A capacity. Do not substitute SOIC or DIP ATtiny84A options without a PCB redesign.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto ATTINY84A-MU
Brand Microchip Technology Microchip Technology
Package 20-lead QFN-EP (4 mm x 4 mm) 20-lead QFN (4 mm x 4 mm)
Architecture 8-bit AVR RISC 8-bit AVR RISC
Maximum Clock Frequency 20 MHz 20 MHz
Flash Memory 8 KB 8 KB
EEPROM 512 bytes 512 bytes
SRAM 512 bytes 512 bytes
General-Purpose I/O 12 lines 12 lines
ADC 8-channel, 10-bit 8-channel, 10-bit
Timer/Counter Resources 2 timer/counters, 4 PWM channels 2 timer/counters, 4 PWM channels
Operating Voltage 1.8 V to 5.5 V 1.8 V to 5.5 V
Operating Temperature -40 °C to +85 °C -40 °C to +85 °C
Exposed Thermal Pad Yes No exposed pad in the MUR/MU package designation

Pangunahing mga Pagkakaiba

  • Exposed-pad construction supports thermal dissipation (kumpara saATTINY84A-MU)
  • Full 8 KB program memory in a compact 4 mm square footprint (kumpara saATTINY44A-MFR)
  • Integrated eight-channel analog conversion (kumpara saATTINY84A-MU)

Talaan ng Disenyo

The 4 mm by 4 mm QFN-EP package relies on its exposed pad for heat spreading. Route the pad to ground with the manufacturer-recommended thermal-via pattern and keep it clear of sensitive analog routing. Because the package is small, sustained high clock rates and continuously loaded GPIO outputs can still raise junction temperature; provide copper area rather than relying only on narrow pad connections. Review the official land pattern before the exposed-pad connection is copied from a generic QFN footprint.

Place the device-side supply capacitor at the VCC pin and use a short, low-impedance ground return for both decoupling and the exposed pad. Keep analog inputs connected to the ADC pins away from PWM outputs, clock signals, and switching nodes. Reserve the ISP or ICSP connector because in-system programming is a defining feature of this controller. Confirm the exact pin names and exposed-pad connection in the official ATtiny84A pin-description table before releasing artwork.

Do not treat ATtiny84A members with the same family name as automatically interchangeable. The ATTINY84A-SSU uses a different lead arrangement from the ATTINY84A-MUR, while the ATTINY44A-MFR has less program memory. Also avoid assuming that a replacement is thermal-equivalent: the ATTINY84A-MUR specifies an exposed pad whereas the ATTINY84A-MU does not. Confirm the package drawing, memory capacity, programmed firmware requirements, and board land pattern as a single compatibility decision.

For battery-powered designs operating from 1.8 V to 5.5 V, select a regulator whose dropout and quiescent behavior match the average load rather than the 20 MHz peak processing requirement. Use sleep modes between sensor samples and keep interrupt handlers short because the device has 512 bytes of SRAM. Place the local bypass capacitor close to the supply pin and validate the power rail during the 20 MHz operating state, not only while the controller is sleeping.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The JLCPCB component listing identifies the ATTINY84A-MUR as RoHS compliant. No separate REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification statements were identified for this exact MPN.

Data napatotohanan sa: 2026-11-19 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

attiny84a mur attiny84a pinout attiny84a datasheet attiny84a vs attiny85 attiny84a programming attiny84a arduino attiny84a ssu attiny84a ssf attiny84a ssur ATTINY84A-MUR equivalent ATTINY84A-MUR replacement ATTINY84A-MUR 20MHz QFN Microchip ATTINY84A-MUR ATTINY84A-MUR price ATTINY84A-MUR stock

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology ATTINY84A-MUR ATTINY84A-MU ATTINY84A AVR 8-bit RISC microcontroller TinyAVR picoPower ISP Flash memory EEPROM SRAM general-purpose I/O timer/counter PWM analog-to-digital converter 10-bit ADC In-System Programming ICSP MPLAB Snap QFN-20 QFN package family surface mount exposed pad RoHS industrial temperature range
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ