ATTINY84A-MUR - 20MHz 8KB AVR MCU | Microchip
料号: ATTINY84A-MUR ✓ 量产中ATTINY84A-MUR 概述
An 8-bit microcontroller is a programmable semiconductor that executes a compact instruction set to read sensors, control actuators, and manage communications. Within the product hierarchy, the ATTINY84A belongs to the AVR 8-bit microcontroller family, the TinyAVR subfamily, and the power-efficient picoPower product line. It combines small memory capacity with dedicated analog and timing resources for cost-sensitive embedded systems.
Principal features include an 8-channel, 10-bit successive-approximation analog-to-digital converter, two timer/counters with 8-bit and 16-bit operating modes, four PWM channels, 32 general-purpose working registers, internal and external interrupt capability, and an 8 KB ISP Flash program memory area. The 12 GPIO pins support digital interfaces, while the ADC provides 10-bit conversion resolution for analog measurement and control.
The ATTINY84A operates across a 1.8 V to 5.5 V supply range and an industrial temperature range of -40 °C to +85 °C. Its RISC architecture and picoPower technology target low processing overhead and efficient operation in battery-powered equipment. ISP programming allows firmware to be loaded and updated through a dedicated programming interface, while the same pins also provide ICSP debugging capability described by Microchip.
Typical uses include compact sensor nodes, battery-operated instrumentation, LED lighting controllers, analog monitoring modules, compact motor-control subsystems, and small automation controllers. The 4 mm square QFN-EP package reduces board area, while the exposed thermal pad improves heat dissipation when the device operates continuously.
For PCB design, route the exposed pad to ground and follow the manufacturer land-pattern and thermal-via requirements. Provide a stable local supply decoupling arrangement, reserve the ISP programming pins, and verify the external crystal or clock configuration in the manufacturer datasheet before fabrication. Because the ATTINY84A is a memory-limited 8-bit device, applications should avoid unnecessary interrupt service routines and oversized data buffers.
This product page consolidates the core electrical characteristics, package details, programming resources, application guidance, comparison parameters, and the only verified same-footprint alternative for engineering evaluation and sourcing decisions.
直接替换替代料: ATTINY84A-MUR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
ATTINY84A-MU
✅ 直接替换📋 参考替代料(不在目录中)
ATTINY84A-MUR 最大额定值与电气特性
| Architecture | 8-bit AVR RISC |
| Technology | picoPower |
| 最大时钟频率 | 20 MHz |
| Flash Memory | 8 KB (4K x 16), in-system programmable |
| EEPROM | 512 bytes |
| SRAM | 512 bytes |
| General-Purpose I/O Lines | 12 |
| General-Purpose Working Registers | 32 |
| Timer/Counter | 2, with 8-bit and 16-bit modes |
| PWM Channels | 4 |
| Analog-to-Digital Converter | 8-channel, 10-bit ADC |
| 工作电源电压 | 1.8 V to 5.5 V |
| 工作温度范围 | -40 °C to +85 °C |
| Programming Interface | ISP and ICSP |
| 封装 | 20-lead QFN with exposed pad, 4 mm x 4 mm |
| 安装类型 | Surface mount |
| RoHS 状态 | Compliant |
| Interrupts | Internal and external interrupts |
ATTINY84A-MUR 20-lead qfn with exposed pad, 4 mm x 4 mm 引脚配置指南
ATTINY84A-MUR(20-lead qfn with exposed pad, 4 mm x 4 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: ATTINY84A-MUR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATTINY84A-MUR 适用于 6 应用s: Battery-Powered Sensor Node, Compact Analog Monitoring Controller, LED Lighting and Dimming Control, Small Motor and Actuator Control, Programmable Timer and Sequencer, Compact Automation and Interface Module.
Battery-Powered Sensor Node
The ATTINY84A-MUR fits compact battery-powered sensor nodes because its picoPower AVR core operates from 1.8 V to 5.5 V while providing 12 GPIO lines for digital sensors and an 8-channel, 10-bit ADC for analog inputs. Firmware can periodically wake the controller, convert selected analog channels, and transmit measurements before returning to a low-power state. The 512-byte SRAM requires short interrupt routines and buffered acquisition to avoid memory pressure, while the 8 KB flash program area is sufficient for modest sensor-processing and communication logic.
推荐
Compact Analog Monitoring Controller
The ATTINY84A-MUR is well suited to industrial monitoring modules that must acquire several analog signals and apply local control decisions. Its 8-channel, 10-bit ADC supports temperature, pressure, or level sensing, and the 12 general-purpose I/O lines can drive alarm indicators or interface to external logic. At a maximum clock frequency of 20 MHz, the AVR core can execute filtering and threshold routines between samples. The 512-byte SRAM and 8 KB flash are adequate for compact, deterministic monitoring functions but require deliberate data handling.
推荐
LED Lighting and Dimming Control
The ATTINY84A-MUR can control LED lighting systems where four PWM channels and two timer/counters simplify period and duty-cycle management. Its 20 MHz maximum clock provides ample headroom for dimming sequences, button handling, and fault detection, while the 10-bit ADC can monitor a current-sense or potentiometer input. The 8 KB flash footprint accommodates compact lighting tables and state machines. Because the exposed pad improves heat dissipation, continuous LED-indicator and driver-control operation is practical when the package thermal design follows Microchip guidance.
推荐
Small Motor and Actuator Control
The ATTINY84A-MUR supports small motor, solenoid, and actuator-control designs using its two timer/counters, four PWM channels, and 12 GPIO lines. Timer hardware can generate repeatable pulse-width-modulated drive signals while the AVR core handles limit inputs, current feedback, and directional control logic. The 8-channel, 10-bit ADC is useful for reading analog feedback from potentiometers or current-sensing networks. Firmware capacity is limited to 8 KB, so control tables should remain compact and time-critical functions should rely on hardware peripherals.
推荐
Programmable Timer and Sequencer
The ATTINY84A-MUR can serve as a compact programmable timer or sequencer for instruments, test fixtures, and laboratory equipment. Two timer/counters provide independent timing resources, four PWM channels support actuator outputs, and the 12 I/O lines can drive step indicators or control external switches. Its 20 MHz maximum clock supports responsive event sequencing, and the 512-byte SRAM is adequate for short state tables rather than large waveform buffers. ISP programming also allows operating profiles to be changed without removing the assembled controller.
推荐
Compact Automation and Interface Module
The ATTINY84A-MUR is appropriate for small automation modules that translate switches, sensors, or analog levels into controlled outputs. Twelve GPIO lines can handle multiple digital inputs and outputs, while the 10-bit ADC adds analog sensing without an external converter. Operating from 1.8 V to 5.5 V permits integration with low-voltage sensors and modern logic families, and the 20 MHz clock supports responsive protocol handling. The limited 8 KB program area and 512-byte SRAM make it most appropriate for focused tasks rather than protocol-heavy gateways.
推荐
推荐产品汇总
工程参考数据: ATTINY84A-MUR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATTINY84A-MU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-lead QFN-EP (4 mm x 4 mm) | 20-lead QFN (4 mm x 4 mm) |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Frequency | 20 MHz | 20 MHz |
| Flash Memory | 8 KB | 8 KB |
| EEPROM | 512 bytes | 512 bytes |
| SRAM | 512 bytes | 512 bytes |
| General-Purpose I/O | 12 lines | 12 lines |
| ADC | 8-channel, 10-bit | 8-channel, 10-bit |
| Timer/Counter Resources | 2 timer/counters, 4 PWM channels | 2 timer/counters, 4 PWM channels |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C |
| Exposed Thermal Pad | Yes | No exposed pad in the MUR/MU package designation |
关键差异点
- Exposed-pad construction supports thermal dissipation (对比 ATTINY84A-MU)
- Full 8 KB program memory in a compact 4 mm square footprint (对比 ATTINY44A-MFR)
- Integrated eight-channel analog conversion (对比 ATTINY84A-MU)
设计说明
The 4 mm by 4 mm QFN-EP package relies on its exposed pad for heat spreading. Route the pad to ground with the manufacturer-recommended thermal-via pattern and keep it clear of sensitive analog routing. Because the package is small, sustained high clock rates and continuously loaded GPIO outputs can still raise junction temperature; provide copper area rather than relying only on narrow pad connections. Review the official land pattern before the exposed-pad connection is copied from a generic QFN footprint.
Place the device-side supply capacitor at the VCC pin and use a short, low-impedance ground return for both decoupling and the exposed pad. Keep analog inputs connected to the ADC pins away from PWM outputs, clock signals, and switching nodes. Reserve the ISP or ICSP connector because in-system programming is a defining feature of this controller. Confirm the exact pin names and exposed-pad connection in the official ATtiny84A pin-description table before releasing artwork.
Do not treat ATtiny84A members with the same family name as automatically interchangeable. The ATTINY84A-SSU uses a different lead arrangement from the ATTINY84A-MUR, while the ATTINY44A-MFR has less program memory. Also avoid assuming that a replacement is thermal-equivalent: the ATTINY84A-MUR specifies an exposed pad whereas the ATTINY84A-MU does not. Confirm the package drawing, memory capacity, programmed firmware requirements, and board land pattern as a single compatibility decision.
For battery-powered designs operating from 1.8 V to 5.5 V, select a regulator whose dropout and quiescent behavior match the average load rather than the 20 MHz peak processing requirement. Use sleep modes between sensor samples and keep interrupt handlers short because the device has 512 bytes of SRAM. Place the local bypass capacitor close to the supply pin and validate the power rail during the 20 MHz operating state, not only while the controller is sleeping.
合规信息
The JLCPCB component listing identifies the ATTINY84A-MUR as RoHS compliant. No separate REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification statements were identified for this exact MPN.