Broadcom

BCM5482SA1IFB - Dual-Port Gigabit Ethernet PHY | Broadcom

MPN: BCM5482SA1IFB ✓ Nakahanda
121-pin BGA Package 10 Mb/s, 100 Mb/s, and 1000 Mb/s Speed
MOQ: 1 |

BCM5482SA1IFB Ulas

The Broadcom BCM5482SA1IFB is a dual-port 10/100/1000BASE-T Ethernet transceiver designed for compact network-interface equipment. It integrates two Gigabit Ethernet PHYs, driver and receiver functions, and RGMII support in a 121-pin BGA package. Its reduced-pin-count interface is intended to simplify routing, reduce PCB layer requirements, and lower system cost in space-constrained applications.

An Ethernet transceiver such as the BCM5482SA1IFB belongs to the physical-layer IC category within the broader hierarchy of network-interface ICs, Ethernet controllers, and semiconductor interface devices. It converts between digital data interfaces and copper Ethernet physical channels, while supporting both 10 Mb/s, 100 Mb/s, and 1000 Mb/s operation. Integrating two ports in one package can reduce component count when equipment requires multiple network connections.

Key features include a dual-port 10/100/1000BASE-T configuration, integrated full-duplex transceiver operation, and a 121-ball BGA package. The RGMII clock timing can be adjusted to compensate for PCB trace delay, reducing sensitivity to routing length and helping simplify system-level timing design. These features make the device applicable to IP phones, network terminals, access equipment, and other products requiring compact multiport Ethernet connectivity.

The BCM5482SA1IFB is particularly relevant to space-constrained designs because one package provides two Gigabit Ethernet channels. Compared with using separate single-port PHYs, consolidation can simplify the bill of materials and reduce the number of routed network channels on the PCB. The RGMII timing-adjustment capability further supports practical board implementation by allowing interface timing to be tuned for propagation delay introduced by printed-circuit traces.

Typical applications include dual-port IP phones, VoIP terminals, customer-premises equipment, network interface controllers, industrial Ethernet endpoints, and embedded gateways. In an IP phone, the device can connect a processor or application controller to two copper Ethernet ports while using the RGMII interface for data transfer. In a compact gateway, the same integration can conserve board area and reduce component count.

Designers should confirm the required PHY features, supported RGMII modes, electrical characteristics, and thermal limits against the manufacturer datasheet before schematic release. PCB layout must follow the package ball map and recommended high-speed and power-distribution guidance. RGMII trace timing, clock routing, return paths, and decoupling should be evaluated together because interface timing margin depends on the complete interconnect.

This page organizes the BCM5482SA1IFB into practical selection, application, comparison, and design-guidance sections. It highlights the part's dual-port Gigabit Ethernet role, 121-BGA footprint, and adjustable RGMII clock timing while clearly separating confirmed characteristics from parameters that require design review.

Mga alternatibo na pwedeng ilagay na BCM5482SA1IFB — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

BCM5482SA2IFBG

✅ Drop-In
📦 121-BGA
Port count remains 2/2 and package remains 121-BGA; revision-specific feature differences are not quantified in the available documentation.

📋 Alternatibo na Reference (hindi sa katalogo)

BCM5482SEA2IFB

✅ Drop-In
📦 121-BGA
Dual-port 10/100/1000BASE-T classification is retained; the S-family suffix indicates a distinct variant, with 0 confirmed port-count changes.

📋 Alternatibo na Reference (hindi sa katalogo)

BCM5482SA1IFB Mga Pinakamataas na Rating at Electrical Characteristics

Product Type Dual-port 10/100/1000BASE-T Ethernet transceiver
Number of Ethernet Ports 2 ports
Supported Ethernet Speeds 10 Mb/s, 100 Mb/s, and 1000 Mb/s
Physical Layer Standard 10/100/1000BASE-T
Transceiver Configuration 2/2 full-duplex transceiver configuration
Digital Interface RGMII
RGMII Clock Timing Adjustment Adjustable
Package Type 121-pin BGA
Bilang ng Pin 121 pins
Uri ng Pagpapasok Surface mount
Tindminan RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable
Lead-Free Status unknown
Halogen-Free Status unknown

Gabay sa Pin Configuration ng BCM5482SA1IFB 121-pin bga

Pin configuration para sa BCM5482SA1IFB (121-pin bga package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 121-pin bga package para sa BCM5482SA1IFB

Wala ng detalyadong pinout data na magagamit para sa BCM5482SA1IFB.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

BCM5482SA1IFB ay nararapat para sa 6 aplikasyons: Dual-Port IP Phone, VoIP Network Terminal, Customer Premises Equipment, Industrial Ethernet Gateway, Network Interface Controller, Embedded Ethernet Bridge.

📱

Dual-Port IP Phone

The BCM5482SA1IFB fits a dual-port IP phone that must expose both 10/100/1000BASE-T connections while keeping the PCB compact. Its two integrated Ethernet physical layers provide two full-duplex channels in one 121-pin BGA rather than requiring separate single-port PHY packages. The RGMII interface carries high-speed parallel data between the PHY and application controller, while adjustable clock timing helps accommodate PCB propagation delay. This integration reduces component count and routing complexity, although the final design still requires careful BGA escape routing, decoupling, RGMII length matching, and thermal qualification for the phone's enclosure and power budget.

🌐

VoIP Network Terminal

The BCM5482SA1IFB is appropriate for a VoIP terminal that combines one Ethernet link for network connectivity with a second link for a downstream device, phone, or pass-through connection. Supporting 10, 100, and 1000 Mb/s allows the terminal to negotiate the highest rate supported by the attached network. Two physical-layer channels in a single 121-pin BGA simplify the component arrangement in space-constrained hardware. The primary engineering trade-off is that RGMII timing must remain reliable across PCB temperature and manufacturing variation, so clock adjustment should be characterized using the final stack-up rather than a generic simulation assumption.

🏭

Customer Premises Equipment

The BCM5482SA1IFB can serve dual-port customer-premises equipment that must terminate copper Ethernet on a compact board. Its 10/100/1000BASE-T capability supports access-network links operating at different negotiated rates, while the two-port integration avoids placing two independent PHY packages on the PCB. The RGMII interface provides a direct digital connection to a network controller or communications processor. For an enclosure-mounted CPE product, designers should still check the manufacturer's recommended copper and magnetics interface details, verify regulatory implementation requirements, and validate the 121-BGA assembly process before committing to a high-volume production layout.

⚡

Industrial Ethernet Gateway

The BCM5482SA1IFB is well matched to a compact industrial gateway requiring two Gigabit-capable copper Ethernet connections. Integrating both 10/100/1000BASE-T PHYs into one 121-pin BGA reduces board area and component count compared with a discrete two-PHY arrangement. Adjustable RGMII clock timing gives the design team a mechanism for accommodating trace delay introduced by the final multilayer PCB. Industrial deployment also requires attention to operating-temperature limits, power-loss behavior, surge mitigation, and grounding. Those details should be confirmed against the manufacturer datasheet and the gateway's external network-protection circuitry before production release.

🖥️

Network Interface Controller

The BCM5482SA1IFB can provide the physical layer beneath a dedicated network interface controller or communications processor. Two RGMII-connected 10/100/1000BASE-T channels allow one host processor or controller to manage two Ethernet links without separate PHY packages. The resulting shared-device architecture can simplify software-visible link management and reduce PCB component count. The main design responsibility is signal integrity across the RGMII host interface, particularly clock jitter, skew, lane alignment, and package-exit delay. Use the manufacturer's recommended topology and timing configuration, and keep high-speed traces away from noisy switching nodes and Ethernet magnetics.

🧩

Embedded Ethernet Bridge

The BCM5482SA1IFB fits an embedded Ethernet bridge that needs to translate between a digital processor interface and two copper network ports. Supporting 10, 100, and 1000 Mb/s allows each link to negotiate independently with connected equipment. Combining the two physical layers in one 121-pin BGA is especially useful where board area is constrained by a connector-dense front panel. The adjustable RGMII clock timing can reduce sensitivity to board-trace delay, but the setting must be established from the actual routed topology. Production validation should include negotiated-speed testing, packet-transfer integrity, power cycling, and compatibility testing with the intended magnetics and connector implementation.

Buod ng mga Inirekomendang Produkto

BCM5482SA1IFB Broadcom Ginagamit sa: Dual-Port IP Phone, VoIP Network Terminal, Customer Premises Equipment, Industrial Ethernet Gateway, Network Interface Controller, Embedded Ethernet Bridge BCM5482SA2IFBG Same-family dual-port transceiver option Ginagamit sa: Dual-Port IP Phone, Customer Premises Equipment, Industrial Ethernet Gateway, Embedded Ethernet Bridge BCM5482SEA2IFB Same-family two-port Ethernet option Ginagamit sa: VoIP Network Terminal, Network Interface Controller
What is the BCM5482SA1IFB?
The BCM5482SA1IFB is a Broadcom dual-port 10/100/1000BASE-T Ethernet transceiver with RGMII support in a 121-pin BGA package. According to the manufacturer documentation, it consolidates two Gigabit Ethernet physical-layer channels to reduce component count and simplify routing in compact network-interface products. It is intended for applications requiring copper Ethernet connectivity through a digital RGMII interface.
How many Ethernet ports does BCM5482SA1IFB support?
The BCM5482SA1IFB supports two 10/100/1000BASE-T Ethernet ports. Broadcom describes the device as a dual-port Gigabit Ethernet transceiver with a 2/2 full-duplex transceiver configuration. Combining both physical-layer channels in one 121-pin BGA package can simplify PCB layout compared with using two separate single-port PHY devices.
What Ethernet speeds are supported by BCM5482SA1IFB?
The BCM5482SA1IFB supports 10 Mb/s, 100 Mb/s, and 1000 Mb/s operation over 10/100/1000BASE-T. The manufacturer identifies the part as a dual-port Gigabit Ethernet transceiver. Automatic support across these rates allows the same physical design to accommodate legacy 10/100 links as well as Gigabit connections.
Where can I download the BCM5482SA1IFB datasheet PDF?
The official Broadcom BCM5482 documentation is available through the manufacturer document portal at https://docs.broadcom.com/doc/12358218. Use the manufacturer document to confirm the ball map, RGMII configuration, electrical characteristics, timing limits, and layout recommendations before releasing a PCB design. A separate distributor-hosted PDF should be used only when its revision can be matched to the current manufacturer document.
Where can I find the BCM5482SA1IFB pinout?
The BCM5482SA1IFB uses a 121-pin BGA package, and its complete numbered ball assignment should be taken from the manufacturer datasheet. The package data in this listing confirms a 121-pin device but does not reproduce individual ball names, so the detailed pin table is not presented here. Assign PCB nets from the official ball-map table to prevent orientation and power-net mistakes.
Can BCM5482SA1IFB compensate for RGMII board-trace delay?
Yes, the BCM5482SA1IFB includes adjustable RGMII clock timing that can compensate for PCB trace delay. Broadcom specifically describes this capability as a way to eliminate board-trace delay otherwise required by the RGMII specification. The adjustment should be validated in the final layout because connector, via, and layer-transition effects all contribute to total interconnect delay.
BCM5482SA1IFB vs BCM5482SA2IFBG - which is the better replacement?
The BCM5482SA2IFBG is the closer documented same-package alternative because it is also identified as a 2/2 full-duplex Ethernet transceiver in a 121-BGA package. The BCM5482SA1IFB and BCM5482SA2IFBG share the same dual-port 10/100/1000BASE-T architecture, but revision-specific features are not established here. Confirm register compatibility, RGMII options, and electrical requirements before substitution.
When should I choose BCM5482SA1IFB over BCM5482SA2IFBG?
Choose the BCM5482SA1IFB when it is the released or approved device for the existing design and its RGMII behavior meets the product requirements. Consider the BCM5482SA2IFBG only after confirming pin, register, clocking, and application compatibility. Both are 121-BGA, two-port Gigabit Ethernet transceiver options, so the deciding factors are the exact revision requirements and qualification status of the target product.
Is BCM5482SA1IFB suitable for a dual-port IP phone design?
The BCM5482SA1IFB is suitable for a dual-port IP phone when two 10/100/1000BASE-T connections and RGMII integration are required. Its two physical-layer channels occupy one 121-pin BGA package, while adjustable RGMII clock timing helps address printed-circuit trace delay. Validate the complete interface timing, thermal environment, and mechanical assembly process in the target design.
What can replace BCM5482SA1IFB without redesigning the PCB?
The BCM5482SA2IFBG is the strongest documented drop-in candidate for the BCM5482SA1IFB because both use a 121-BGA package and implement a two-port Gigabit Ethernet transceiver. Before replacing the device, verify every BGA assignment, supported RGMII mode, strap configuration, register behavior, and electrical limit against the manufacturer datasheet. The available cross-reference information does not establish enough additional drop-in candidates to provide a broader verified list.
Is BCM5482SA1IFB the same as BCM5482SEA2IFB?
No, the BCM5482SA1IFB and BCM5482SEA2IFB are not equivalent MPNs, even though both are described as dual-port 10/100/1000BASE-T Ethernet devices. The BCM5482SEA2IFB carries a different family suffix, so its exact revision and pin compatibility must be checked independently. Do not substitute it solely because the Ethernet port count and speed categories match.
What are the key specifications of BCM5482SA1IFB that engineers should know?
The BCM5482SA1IFB combines two 10/100/1000BASE-T Ethernet ports, RGMII connectivity, adjustable RGMII clock timing, and a 121-pin BGA package in one device. Broadcom positions the integrated dual-channel design for lower component count and fewer PCB layers in space-constrained IP phone and network-interface applications. Supply voltage, current, temperature limits, and exact timing values require confirmation from the manufacturer datasheet.
Where can I buy BCM5482SA1IFB and check its lead time?
Use the Request a Quote form on this page to ask for BCM5482SA1IFB availability, current lead time, minimum order quantity, and package quantity. The quote team can confirm the exact BCM5482SA1IFB ordering code and delivery position. Because these commercial terms can change with supply conditions, request a written quotation for the planned production quantity.
Is BCM5482SA1IFB in stock?
Current BCM5482SA1IFB stock should be confirmed through the Request a Quote form on this page. Submit the required quantity, target date, and acceptable delivery terms for a current supply response. Inventory can vary by package, quantity, and regional logistics, so a confirmed production allocation is more useful than a general stock indication.
How should BCM5482SA1IFB be handled in a PCB layout?
Place the BCM5482SA1IFB according to the manufacturer ball map and preserve continuous supply and ground distribution around the 121-pin BGA. Route RGMII clock and data signals as a controlled-length group, provide suitable return paths, and follow the datasheet's decoupling recommendations. Validate signal and power integrity on the final stack-up because package escape routing and RGMII timing margin are tightly coupled.

Impormasyon ng Talumpati sa Engineering for BCM5482SA1IFB — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the BCM5482SA1IFB for a compact dual-port Ethernet design that requires 10/100/1000BASE-T operation, RGMII connectivity, and adjustable clock timing in a 121-BGA package. Its two integrated physical layers can simplify IP phone, CPE, gateway, and embedded-bridge layouts by replacing two separate single-port devices. The BCM5482SA2IFBG is the leading documented same-package candidate when the original part is unavailable, but register behavior, strap options, RGMII modes, and qualification must be checked before substitution. The BCM5482SEA2IFB offers a related dual-port configuration, but its distinct family suffix requires a more conservative compatibility review. Because the available cross-reference results do not establish five qualified drop-ins, engineers should base final selection on the manufacturer datasheet rather than assuming electrical interchangeability from the shared package and port count.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto BCM5482SA2IFBG BCM5482SEA2IFB
Brand Broadcom Broadcom Broadcom
Package 121-BGA 121-BGA 121-BGA
Device Type Dual-port 10/100/1000BASE-T Ethernet transceiver Dual-port 10/100/1000BASE-T Ethernet transceiver Dual-port 10/100/1000BASE-T Ethernet PHY
Ethernet Port Count 2 ports 2 ports 2 ports
Supported Speeds 10/100/1000 Mb/s 10/100/1000 Mb/s 10/100/1000 Mb/s
Pin Count 121 pins 121 pins 121 pins
Mounting Type Surface mount Surface mount Surface mount

Pangunahing mga Pagkakaiba

  • Two Gigabit-capable Ethernet channels in one package (kumpara saBCM5482SA2IFBG)
  • Adjustable RGMII clock timing (kumpara saBCM5482SEA2IFB)
  • Compact two-port integration for terminal equipment (kumpara saBCM5482SA2IFBG)

Talaan ng Disenyo

Route RGMII clock, data, and control signals as a matched interface and use the BCM5482 adjustable clock-timing feature to compensate for the actual routed delay. Keep the BGA escape paths short, provide continuous return planes, and avoid splitting supply planes beneath the device. Validate timing after final-layer assignment because changing layer transitions can alter skew and propagation delay even when nominal trace lengths remain unchanged.

Implement the 121-BGA footprint with the manufacturer-recommended pad, solder-mask, and paste geometry, and verify the ball map against the exact ordering variant. Place input and output decoupling capacitors close to their designated BGA balls while maintaining a low-impedance ground reference. X-ray or equivalent assembly inspection is advisable because hidden solder defects under the BGA can create intermittent Ethernet or RGMII failures.

Separate the RGMII clocks and data paths from Ethernet magnetics, switching regulators, and other high-current or high-edge-rate nodes. Use uninterrupted reference planes and check RGMII setup and hold timing with board-level compensation, including temperature and manufacturing variation. Ethernet copper-channel validation remains necessary because compliant PHY timing does not by itself guarantee compliance at the connector without the intended external network interface.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The manufacturer documentation identifies BCM5482 as a dual-port Ethernet PHY family, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. Compliance status must be confirmed for the exact ordering code and manufacturing site before procurement.

Data napatotohanan sa: 2026-11-15 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

BCM5482SA1IFB datasheet BCM5482SA1IFB pinout BCM5482SA1IFB datasheet pdf BCM5482SA1IFB equivalent BCM5482SA1IFB replacement BCM5482SA1IFB cross reference BCM5482SA1IFB footprint BCM5482SA1IFB RGMII Broadcom BCM5482SA1IFB BCM5482SA1IFB price BCM5482SA1IFB stock BCM5482SA1IFB vs BCM5482SA2IFBG 121-BGA dual-port Ethernet PHY BCM5482 dual-port Gigabit Ethernet PHY

Mga kaugnay na Mga Komponente at mga Tuntunin

Broadcom BCM5482SA1IFB BCM5482SA2IFBG BCM5482SEA2IFB Ethernet transceiver Ethernet PHY 10/100/1000BASE-T Gigabit Ethernet RGMII physical-layer IC network-interface IC interface IC semiconductor 121-BGA BGA package surface-mount package full-duplex transceiver RGMII clock timing PCB trace delay IP phone customer premises equipment industrial Ethernet gateway embedded Ethernet bridge RGMII
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ