CD4097BPW - 20V Differential 8:1 CMOS Multiplexer | TI
MPN: CD4097BPW ✗ Tapus ng BuhayCD4097BPW Ulas
A CMOS analog multiplexer is an interface IC that connects one of several input terminals to a common output under digital address-control signals. A demultiplexer performs the reverse routing function. The CD4097B family combines both operating roles in one device, while its differential configuration provides two outputs whose states are opposite at any selected channel, allowing complementary, inverting, and non-inverting signal paths without duplicating external switching.
The principal electrical features include a 20 V maximum supply rating, an 8:1 configuration, approximately 240 ohm on-state resistance, and a leakage-current value shown as 100 nA in the part listing. The CD4097BPW ordering option uses a 24-pin TSSOP package. Its address inputs allow digital control systems to scan multiple sensors or route a single conditioning chain toward one of eight sources, reducing component count and simplifying synchronization.
CMOS construction supports low-power operation and high input impedance, which is valuable when the multiplexed sources include high-impedance sensors, amplifiers, or precision measurement nodes. The paired outputs are especially useful when a system requires a selected signal and its complement, such as in bridge excitation, differential excitation, or dual-polarity reference routing. The exact switching speed, channel capacitance, common-mode limits, and static current should be confirmed in the TI CD40x7B datasheet before final timing and signal-integrity analysis.
Typical uses include multiplexed data acquisition, sensor-channel selection, automated test systems, industrial measurement interfaces, and control systems that must share one amplifier or converter across several inputs. In these applications, the address logic can operate from a microcontroller or programmable logic controller while the analog section remains at a compatible supply voltage. Designers should account for off-channel isolation, charge injection, settling time, and the resistance of the selected path when specifying downstream gain and precision.
PCB implementation requires careful handling of high-impedance and low-level analog nodes. Place the multiplexer close to the signal sources or the first low-noise input stage, keep analog traces short, provide a stable ground reference, and decouple the supply close to the device. Avoid routing address and digital-control signals beneath sensitive analog nets where switching activity could couple into the measurement channel.
This page combines manufacturer specifications, practical interface guidance, application fit, and a conservative drop-in assessment. It also highlights where engineers must validate timing, leakage, analog settling, and lifecycle risk against the manufacturer datasheet and the specific signal-chain requirements.
Mga alternatibo na pwedeng ilagay na CD4097BPW — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboCD4097BPW Mga Spesipikasyon
| Product Type | Differential 8:1 CMOS analog multiplexer and demultiplexer |
| Number of Switch Circuits | 2 circuits |
| Multiplexer Configuration | 8:1 |
| Maximum Supply Voltage | 20 V |
| On-State Resistance | 240 ohm |
| Leakage Current | 100 nA |
| Volte ng Pagbibigay | 5 V |
| Packhaging | 24-pin TSSOP |
| Package Width | 4.40 mm |
| Package Height | 0.173 mm |
| Bilang ng Pins | 24 pins |
| Uri ng Pagpapasok | Surface mount |
| Logic Family | CD4000B CMOS |
| Differential Outputs | 2 complementary outputs |
| Multiplexing and Demultiplexing | Multiplexer and demultiplexer operation |
| Tindminan RoHS | RoHS compliant |
| Lead-Free Status | Lead-free |
Gabay sa Pin Configuration ng CD4097BPW 0.173 mm
Pin configuration para sa CD4097BPW (0.173 mm package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa CD4097BPW.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
CD4097BPW ay nararapat para sa 6 aplikasyons: Multiplexed Data Acquisition, Industrial Sensor Channel Selection, Automated Test Equipment, Differential Bridge Excitation, Control-System Signal Routing, Precision Signal Conditioning.
Multiplexed Data Acquisition
The CD4097BPW suits data-acquisition front ends that must select one of eight sensor or analog inputs and route it into a shared amplifier or converter. Its 8:1 configuration reduces the number of signal-chain inputs, while the differential outputs can support paired measurement routing. The 240 ohm on-state resistance must be included in the source-impedance and gain-error calculation. The TI CD40x7B datasheet should be used to confirm switching time, channel capacitance, charge injection, and isolation before setting the acquisition aperture.
Inirekomenda
Industrial Sensor Channel Selection
The CD4097BPW can scan eight high-impedance sensor outputs in industrial monitoring equipment while sharing one downstream signal-conditioning path. Its CMOS implementation and 100 nA listed leakage are relevant when source impedance is high, while the 20 V supply rating supports interface designs operating above low-voltage logic levels. Keep traces short, maintain a stable analog ground, and decouple the supply near the package. Validate the complete error budget because on-resistance, leakage, injection, and settling all influence low-level sensor accuracy.
Inirekomenda
Automated Test Equipment
In automated test equipment, the CD4097BPW can route one of eight test points to a common measurement amplifier, comparator, or return channel. The complementary outputs allow the selected source and an opposite-polarity path to be presented together, which can simplify fixture interfaces and differential excitation. Address decoding should remain outside the sensitive analog region, and unused channels require appropriate handling according to the manufacturer guidance. Confirm switching settling before using the multiplexer near precision threshold measurements.
Inirekomenda
Differential Bridge Excitation
The CD4097BPW's complementary output pair is useful in bridge and differential excitation systems where two opposite signal states are required during channel selection. It can alternate excitation routing without duplicating an entire eight-channel switching network. The design must account for the 240 ohm on-state resistance in excitation amplitude and settling, and the 100 nA leakage figure must remain small relative to the sensing circuit. Use a symmetric, low-impedance layout and consult the TI timing and application information before finalizing bridge excitation limits.
Inirekomenda
Control-System Signal Routing
The CD4097BPW allows a microcontroller or programmable control system to choose among eight analog command or feedback signals without dedicating separate amplifiers to each route. The 8:1 architecture supports compact control panels, condition-monitoring controllers, and actuator-interface boards. Address outputs should be driven with compatible CMOS levels, and switching transients must not overlap critical control updates unless the acquisition and settling requirements permit it. The manufacturer timing diagram provides the basis for sequencing the address pins and changing channels.
Inirekomenda
Precision Signal Conditioning
The CD4097BPW can place one of eight conditioned inputs onto a shared low-noise amplifier or differential measurement chain, reducing component count while retaining selectable inputs. Its 240 ohm on-state resistance is small relative to many sensor-source impedances but remains relevant for high precision, and the listed 100 nA leakage must be included when calculating bias error. Place the device close to the amplifier input, use quiet supply decoupling, and isolate address traces from the analog path to minimize switching coupling.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for CD4097BPW — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Package | 24-pin TSSOP |
| Brand | Texas Instruments |
| Multiplexer Configuration | 8:1 differential |
| Switch Circuits | 2 circuits |
| Maximum Supply Voltage | 20 V |
| On-State Resistance | 240 ohm |
| Leakage Current | 100 nA |
| Logic Family | CD4000B CMOS |
| Lifecycle Status | Not recommended for new designs |
Pangunahing mga Pagkakaiba
- Provides paired complementary outputs in an 8:1 multiplexer (kumpara saCD4067BPW)
- Supports a higher operating interface voltage than common low-voltage logic multiplexers (kumpara sa74FST3384DTR2)
- Combines multiplexing and demultiplexing functions (kumpara saSN74CBTLV3384PWR)
Talaan ng Disenyo
Route the eight analog inputs and the two outputs as short, compact nets, especially when the source impedance is high or signal amplitudes are small. Place CD4097BPW near the shared amplifier or converter input rather than beside the system connector. Keep the address inputs and inhibit control away from sensitive analog traces. A solid, uninterrupted ground plane provides the lowest-impedance return path and reduces susceptibility to address-line coupling.
Follow the TI CD40x7B datasheet, Rev. D, for the permitted supply range and decoupling configuration. Place the required supply bypass capacitor close to the device's supply pins and provide an adequate return path to the ground pins. Avoid long supply loops through the analog section because the 240 ohm switch resistance is only one contributor to total measurement error; supply impedance and ground bounce can add further noise during address transitions.
Include off-channel isolation, charge injection, on-state resistance, leakage current, and output settling in the acquisition error budget. The listed 100 nA leakage is especially relevant to high-impedance sources, while the 240 ohm on-state resistance can create gain error when the source impedance is significant. Use the manufacturer timing diagrams to determine how long the address inputs must remain stable before the selected output is sampled.
Do not treat every 24-pin TSSOP multiplexer as a drop-in replacement. CD4067BPW has a 16:1 configuration rather than the CD4097BPW's 8:1 differential arrangement, while the listed 74FST3384DTR2 comparison does not establish identical pinout or complementary-output behavior. Verify the complete pin map, address truth table, logic thresholds, supply range, channel capacitance, and output architecture before approving any substitute.
Impormasyon ng Pagsunod sa Kautusan
A component listing identifies CD4097BPW as RoHS-compliant and lead-free. No additional REACH, halogen-free, conflict-minerals, or automotive qualification status is established for this ordering option.