ICS513MLF - 140MHz Clock Generator | Renesas Electronics
MPN: ICS513MLF ✓ NakahandaICS513MLF Ulas
A PLL clock generator is a clock-timing semiconductor that multiplies a reference frequency and distributes the resulting clock to digital circuits. A crystal reference provides a stable time base, while the internal phase-locked loop derives the required output frequency. Clock-generator ICs belong to the clock and timing hierarchy, where they sit between frequency references and the clocks consumed by processors, communications equipment, and digital logic.
ICS513MLF combines a 140 MHz maximum stated operating frequency with a single clock output and a 5 V supply range. Its LOCO positioning emphasizes a cost-effective implementation for common digital clocking needs. The lead-free 8-SOIC package supports conventional surface-mount assembly and is suitable for compact industrial, communications, and embedded systems that need a local clock source without employing a more complex high-performance frequency synthesizer.
The device operates with CMOS-compatible signals and can use either a 14.31818 MHz crystal or a clock input as its frequency reference. During implementation, the crystal, load capacitance, supply decoupling, and output-drive configuration determine whether the generated clock meets the timing and jitter requirements of the downstream circuit. The manufacturer datasheet should be consulted for the exact reference configuration and electrical limits before finalizing a high-speed design.
Typical uses include clocking digital controllers, standardizing clock distribution across a compact circuit board, and replacing a board-level oscillator plus divider arrangement with a single timing IC. The single-output configuration is especially appropriate when only one derived clock is needed. In multi-domain equipment, the ICS513MLF can supply a common local clock where clock quality and frequency are adequate but multi-output fanout or differential clocking is not required.
PCB implementation requires short return paths and careful treatment of the crystal and high-speed clock traces. Place the reference components close to the device, connect the supply to a low-impedance ground plane, and route clock outputs away from noisy switching nodes. Verify output rise time, duty cycle, jitter, and load capacitance in the finished layout because the complete timing performance depends on component selection and board implementation.
This page combines the identified electrical ratings, package details, sourcing guidance, and application-oriented design considerations for ICS513MLF. It also distinguishes the device from related clock-generator references while clearly identifying parameters that require confirmation against the manufacturer datasheet before production release.
Mga alternatibo na pwedeng ilagay na ICS513MLF — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ICS513MLF (parehas na form factor at footprint) — pagkakaiba sa Device Type.
ICS513M
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →ICS513MLF Mga Spesipikasyon
| Device Type | Clock Generator, Fanout Distribution IC |
| Maximum Operating Frequency | 140 MHz |
| Bilang ng Outputs | 1 output |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Reference Input Frequency | 14.31818 MHz |
| Clock Architecture | LOCO PLL |
| Bus Interface | CMOS |
| Package Type | 8-SOIC (0.154 inch, 3.90 mm width) |
| Uri ng Pagpapasok | Surface Mount |
| Lead-Free Status | Lead-free |
| Product Category | Clock Generators, PLLs, Frequency Synthesizers |
| Output Kumpigurasyon | Single CMOS clock output |
| Phase-Locked Loop Configuration | LOCO PLL multiplier |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Gabay sa Pin Configuration ng ICS513MLF 8-soic (0.154 inch, 3.90 mm width)
Pin configuration para sa ICS513MLF (8-soic (0.154 inch, 3.90 mm width) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ICS513MLF.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ICS513MLF ay nararapat para sa 6 aplikasyons: Digital Controller Clocking, Communications Equipment Timing, Industrial Control Logic, Data Conversion and Interface Timing, Test and Measurement Front Ends, Embedded System Clock Distribution.
Digital Controller Clocking
ICS513MLF fits digital controllers that require one local clock generated from a 14.31818 MHz crystal and a 5 V supply. The device provides a single CMOS output and supports a stated operating frequency up to 140 MHz, making it appropriate for logic, control, and embedded subsystems that need a stable local timing reference without a multi-output synthesizer. Its 8-SOIC footprint simplifies conventional surface-mount assembly, while the LOCO PLL architecture avoids building an oscillator, divider, and output buffer as separate components. Confirm output jitter, duty-cycle limits, fanout, and load capacitance against the target controller requirements, and place the reference network close to the IC.
Inirekomenda
Communications Equipment Timing
ICS513MLF can supply a local derived clock for communications equipment built around a 5 V CMOS logic domain. A 14.31818 MHz crystal reference and the LOCO PLL stage allow the circuit to obtain the required operating clock without implementing discrete frequency synthesis. The single-output arrangement suits a board section with one timing domain, while the 140 MHz stated rating provides headroom for moderately fast digital processing. Keep the crystal path short, maintain a continuous ground reference under the device, and isolate the clock route from switching-power and high-current return paths to minimize timing disturbance.
Inirekomenda
Industrial Control Logic
ICS513MLF is suitable for industrial control logic requiring a compact, dedicated clock source on a 5 V rail. The device’s 140 MHz stated operating frequency and single CMOS output can support processor, state-machine, or interface clocking where one common clock is sufficient. Its 8-SOIC package is well suited to automated PCB assembly and can simplify BOM consolidation by replacing separate oscillator and divider circuitry. In industrial equipment, follow the manufacturer grounding and decoupling guidance, route the clock away from relays and power-converter stages, and verify stability across the intended supply tolerance and ambient conditions.
Inirekomenda
Data Conversion and Interface Timing
ICS513MLF can provide a common clock for data-conversion or interface circuitry operating in a 4.5 V to 5.5 V domain. The one-output CMOS architecture is useful when an ADC, DAC, serializer, or digital interface requires a locally generated clock but does not need multiple independently programmable frequencies. Because timing quality depends on the complete implementation, evaluate jitter, duty-cycle distortion, output rise time, and load behavior using the manufacturer test conditions and the actual PCB. Keep the crystal and clock traces compact and provide a low-impedance return path to reduce susceptibility to coupled noise.
Inirekomenda
Test and Measurement Front Ends
ICS513MLF can establish a local timing reference in compact test and measurement front ends that operate from a 5 V supply. Its 140 MHz stated capability and single CMOS output suit instrument control, acquisition, calibration, and synchronization blocks that need a repeatable digital clock. The 8-SOIC package allows placement close to the timing-consuming circuitry and supports conventional surface-mount production. For sensitive measurements, use a continuous ground plane, minimize clock-trace coupling, and validate jitter and edge quality with the actual cable, probe, and switching loads rather than relying only on unloaded output data.
Inirekomenda
Embedded System Clock Distribution
ICS513MLF is useful in embedded subsystems that need one synchronized CMOS clock for a processor, programmable logic, or peripheral group. A 14.31818 MHz crystal reference and the internal LOCO PLL provide a compact clock source in an 8-SOIC package, reducing the component count compared with discrete oscillator and divider arrangements. Because this is a single-output device, it is most appropriate when the subsystem does not require multiple divided clocks or independently buffered domains. Validate maximum fanout, input capacitance, startup time, and power-supply noise tolerance, and preserve short return paths beneath the timing network.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for ICS513MLF — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ICS513M |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC (0.154 inch, 3.90 mm width) | 8-SOIC (0.154 inch, 3.90 mm width) |
| Device Type | Clock Generator, Fanout Distribution IC | PLL Clock Generator |
Pangunahing mga Pagkakaiba
- Single-output clock generation in a conventional 8-SOIC package (kumpara saICS513M)
- Defined operating-frequency capability (kumpara saICS513M)
- 5 V CMOS integration (kumpara saICS513M)
Talaan ng Disenyo
Place the 14.31818 MHz crystal and its load network directly beside the reference pins, using the shortest practical ground return. Keep the clock output route short and avoid routing it parallel to switching-node or high-current traces. A continuous ground plane beneath the timing section provides a lower-impedance return path and reduces coupling into the reference and output nets.
Place the supply-decoupling capacitor close to the 5 V and ground connections, and verify the capacitor selection against the manufacturer requirements. The supported 4.5 V to 5.5 V range leaves room for a conventional 5 V rail, but supply ripple and transient energy can affect clock-edge quality. Confirm the final rail tolerance and decoupling arrangement in the target system rather than assuming ideal supply behavior.
Do not treat every ICS513 ordering code as an automatic drop-in substitute without checking the pin description and electrical limits. The target uses one output and is identified at 140 MHz, while related family members may differ in temperature grade, frequency, or ordering options. Verify pinout, reference input, output count, supply range, output loading, and package before approving a replacement.
Evaluate output rise time, duty cycle, jitter, and load capacitance with the actual receiver and PCB geometry. A CMOS clock can be sensitive to excessive capacitive loading and improperly terminated stubs. Keep fanout modest, use series damping only where timing analysis supports it, and avoid long point-to-point clock routes when downstream devices can provide a more stable reference.
Impormasyon ng Pagsunod sa Kautusan
The identified package information describes ICS513MLF as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status were not established and are therefore recorded as unknown.