INA152EA/250 - 800 kHz Single-Supply Difference Amplifier | TI
MPN: INA152EA/250 ✓ NakahandaINA152EA/250 Ulas
A difference amplifier is a specialized operational-amplifier configuration that rejects a voltage common to both inputs while amplifying their difference. The INA152 belongs to the precision analog signal-chain hierarchy: instrumentation amplifier, difference amplifier, operational amplifier, analog IC. Its integrated resistor network removes the need for an external matched resistor divider, simplifying current sensing, bridge excitation, and low-level front-end designs while preserving stable ratio behavior over temperature.
Important characteristics include a unity nominal gain, 0.01% gain accuracy from laser trimming, 800 kHz bandwidth, 1.5 mV input offset voltage, and 1 dB gain error. The INA152EA/250 operates across a -40 °C to +85 °C temperature range and is specified for an 8-VSSOP surface-mount package. Its integrated resistor network is designed for accurate common-mode rejection and gain stability across temperature.
The device uses a single-supply architecture, which simplifies analog signal acquisition where a negative supply is unavailable or undesirable. A single supply supports battery-powered, portable, industrial-sensor, and low-power test equipment designs. Because input and output headroom are constrained near the supply rails, the usable input and output common-mode ranges should be confirmed against the manufacturer datasheet for the exact operating voltage.
Typical uses include high-side or low-side current measurement, resistive sensor bridges, differential sensor interfaces, industrial process-control front ends, and low-power diagnostic instruments. The 800 kHz bandwidth is suitable for slow-to-moderate dynamic measurements rather than high-speed waveform capture. The integrated, trimmed network is particularly useful when maintaining accurate differential gain without calibrating several discrete resistors.
For board design, place the device close to the source node and route the differential inputs as a short, tightly coupled pair to minimize pickup of external noise. Connect the ground return directly to the source reference and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Verify supply decoupling, common-mode limits, output drive, and settling behavior in the application that sets the smallest signal of interest.
This page combines manufacturer specifications, package and ordering details, drop-in family alternatives, comparison parameters, and practical design guidance to support component selection, PCB planning, and precision analog front-end design.
Mga alternatibo na pwedeng ilagay na INA152EA/250 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
INA152EA/250G4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
INA152EA/2K5
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
INA152UA/250
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
INA152UA/2K5
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
INA152UA
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
INA152EA/250 Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Precision unity-gain difference amplifier |
| Number of Circuits | 1 circuit |
| Supply Configuration | Single supply |
| Nominal Gain | 1 V/V |
| Bandwidth | 800 kHz |
| Input Offset Voltage | 1.5 mV |
| Gain Error | 1 dB |
| Gain Accuracy | 0.01% from laser-trimmed internal resistors |
| Resistor Network | Integrated precision laser-trimmed resistor network |
| Operational Amplifier Core | CMOS operational amplifier |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
| Packhaging | 8-pin VSSOP (DGK), 0.118 in / 3.00 mm width |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | Compliant |
| Safe Operating Area | Not applicable to this amplifier IC |
Gabay sa Pin Configuration ng INA152EA/250 8-pin vssop (dgk), 0.118 in / 3.00 mm width
Pin configuration para sa INA152EA/250 (8-pin vssop (dgk), 0.118 in / 3.00 mm width package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa INA152EA/250.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
INA152EA/250 ay nararapat para sa 6 aplikasyons: High-Side Current Sensing, Resistive Bridge Sensor Front End, Industrial Process-Control Input, Battery-Powered Portable Instrument, Precision Diagnostic Instrumentation, Low-Level Differential Sensor Interface.
High-Side Current Sensing
The INA152EA/250 fits high-side current measurement when the shunt voltage is small and the common-mode voltage must be rejected. Its unity gain of 1 V/V, 0.01% gain accuracy, and 1.5 mV input offset establish a predictable signal path from the shunt to an ADC or instrumentation stage. Place the amplifier beside the shunt and route the sense pair as a short differential connection. Check that the input common-mode voltage remains within the operating range and that output swing is sufficient at the selected supply voltage.
Inirekomenda
Resistive Bridge Sensor Front End
The INA152EA/250 is appropriate for Wheatstone-bridge outputs because its integrated, laser-trimmed resistor network maintains an accurate unity differential gain while rejecting excitation voltage common to both inputs. The 0.01% gain accuracy avoids the external-resistor mismatch that often limits discrete difference-amplifier implementations. Use a regulated excitation source, keep the bridge return and amplifier ground closely connected, and verify bias-current error for high-impedance sensors. The 800 kHz bandwidth supports sensor bandwidths well below its upper limit.
Inirekomenda
Industrial Process-Control Input
The INA152EA/250 can condition differential process signals in industrial control equipment while operating from a single supply, simplifying analog power planning. Its precision internal resistor ratio provides consistent unity gain, while the specified -40 °C to +85 °C range supports temperature-conditioned equipment. Place the input pair away from contactors, relays, and motor power stages, and use the reference arrangement defined by the manufacturer datasheet when the source is not ground-referenced. Confirm supply range, common-mode limits, and output swing for each analog input range.
Inirekomenda
Battery-Powered Portable Instrument
The single-supply INA152EA/250 architecture suits portable instruments that cannot generate a negative analog rail. Its compact 8-pin VSSOP package and integrated gain-setting network reduce board area and external-component count. The device's low-power design basis is useful for energy-limited measurements, although the exact supply current should be confirmed from the datasheet for the selected operating mode. Use local decoupling and tightly coupled differential routing to preserve accuracy as battery voltage changes.
Inirekomenda
Precision Diagnostic Instrumentation
The INA152EA/250 supports diagnostic instruments that measure small differential signals superimposed on larger common-mode voltages. Unity gain, 1.5 mV input offset, and the laser-trimmed 0.01% gain ratio provide predictable channel behavior. The 800 kHz bandwidth accommodates many sensor and bio-signal front ends without requiring a high-speed amplifier. Verify signal settling, noise performance, and common-mode limits in the final instrumentation configuration, and provide a stable reference return for the source under test.
Inirekomenda
Low-Level Differential Sensor Interface
The INA152EA/250 is useful when a sensor produces a millivolt-scale differential output and its common-mode voltage is much larger. The internal matched network establishes the unity-gain ratio and supports stable common-mode rejection, while the 800 kHz bandwidth leaves margin above most slow sensor response rates. Terminate or filter the input pair according to the source impedance, and check whether input bias current produces meaningful error. Keep sensitive traces away from switching converters and relay contacts.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for INA152EA/250 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | INA152EA/250G4 | INA152EA/2K5 | INA152UA/250 | INA152UA/2K5 | INA152UA |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) |
| Number of Pins | 8 | 8 | 8 | 8 | 8 | 8 |
| Amplifier Function | Single-supply unity-gain difference amplifier | Single-supply unity-gain difference amplifier | Single-supply gain-2.5 difference amplifier | Single-supply unity-gain difference amplifier | Single-supply gain-2.5 difference amplifier | Single-supply unity-gain difference amplifier |
| Nominal Gain | 1 V/V | 1 V/V | 2.5 V/V | 1 V/V | 2.5 V/V | 1 V/V |
| Resistor Network | Integrated precision laser-trimmed network | Integrated precision laser-trimmed network | Integrated precision resistor network | Integrated precision resistor network | Integrated precision resistor network | Integrated precision resistor network |
Pangunahing mga Pagkakaiba
- Unity-gain transfer function preserves source scaling (kumpara saINA152EA/2K5)
- Precision integrated resistor ratio reduces external matching requirements (kumpara saINA152UA/250)
- Single-supply architecture simplifies portable analog systems (kumpara saINA152EA/2K5)
Talaan ng Disenyo
Route the differential input pair as a short, tightly coupled trace from the source to the amplifier. Connect the amplifier ground reference to the source return rather than sharing a long path with digital or switching-current return wires. For shunt measurements, use a Kelvin connection so the sense traces carry only the amplifier input current. This arrangement limits parasitic pickup and prevents the voltage drop in a shared return trace from entering the measured difference.
Keep the INA152EA/250 away from switching nodes, relay contacts, and high-current conductors because its 1.5 mV input offset establishes a sensitive measurement scale. If series input resistors are required for transient protection or filtering, place them symmetrically and confirm that their parasitic resistance does not degrade differential gain accuracy. Use the manufacturer's pin-description table for the final input, reference, output, supply, and ground assignments.
Do not treat the 8-pin package outline as proof of interchangeability. The INA152EA/2K5 family variant has 2.5 V/V gain rather than the INA152EA/250's 1 V/V, which changes downstream scaling and reduces usable output headroom. Before any substitution, compare pin functions, nominal gain, gain error, offset voltage, common-mode range, output swing, supply range, temperature grade, and the manufacturer-recommended layout.
Impormasyon ng Pagsunod sa Kautusan
RoHS-compliant status is identified in the INA152 series distributor listing. The INA152EA/250 is an industrial-temperature analog amplifier rather than an AEC-Q100 automotive-qualified device. Use the Texas Instruments product page and current material-compliance declarations for final procurement approval.