ISL83491IP - 3.3V RS-485/422 Transceiver | Renesas
MPN: ISL83491IP ✓ NakahandaISL83491IP Ulas
An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into differential, balanced line signals. Differential signaling improves noise immunity by rejecting common-mode voltage, while the RS-485 standard supports multipoint buses and the RS-422 standard supports point-to-point or multidrop balanced links. The ISL83491IP belongs to the broader transceiver hierarchy within interface ICs and industrial communication semiconductors.
The device is described as a 3.3 V low-power BiCMOS part that can operate as either a high-speed transceiver or a slew-rate-limited device. This flexibility allows the same pinout and interface architecture to address data rates where low EMI is more important than maximum throughput. The single-driver, single-receiver arrangement also reduces component count in full-duplex RS-422 links, while the driver-enable and receiver-enable functions support controlled bus operation.
The 14-pin DIP package is intended for through-hole PCB assembly and is useful in industrial control equipment, instrumentation, communications adapters, and legacy or leaded systems. A DIP footprint offers generous spacing between leads, which can simplify manual inspection, prototyping, and rework. Designers should still evaluate connector spacing, insulation requirements, grounding, and high-voltage creepage when the transceiver is used in an industrial enclosure.
Typical applications include industrial RS-485 field buses, factory automation links, building-control networks, telemetry equipment, and data-acquisition systems. In an RS-485 network, the transceiver converts the controller's UART logic into a differential bus signal and converts differential bus data back into UART-compatible receive logic. In an RS-422 design, the driver and receiver can support separate point-to-point differential links.
The primary design consideration is bus termination. Long or high-noise RS-485 cables generally use termination at both ends of the bus, while RS-422 commonly places termination at the receiver. The selected data-rate mode, cable length, topology, grounding method, and transceiver count should be evaluated together because excessive loading or incorrect termination can produce reflections and unstable differential voltage.
This product summary consolidates the device function, interface standards, supply range, package details, verified comparison behavior, and practical implementation guidance into one engineering-focused reference for evaluating the ISL83491IP in new and existing through-hole designs.
Mga alternatibo na pwedeng ilagay na ISL83491IP — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ISL83491IP (parehas na form factor at footprint) — pagkakaiba sa Duplex Mode, Maximum Data Rate, Package, Product Type, Transceiver Configuration.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboISL83491IP Mga Spesipikasyon
| Product Type | 1/1 RS-485/RS-422 transceiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Supported Standards | RS-485 and RS-422 |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Technology | BiCMOS |
| Operating Mode | High-speed or slew-rate-limited |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
| Package Type | 14-pin PDIP |
| Uri ng Pagpapasok | Through-hole |
| Logic and Communication | Balanced differential RS-485/RS-422 |
Gabay sa Pin Configuration ng ISL83491IP 14-pin pdip
Pin configuration para sa ISL83491IP (14-pin pdip package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ISL83491IP.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ISL83491IP ay nararapat para sa 6 aplikasyons: Industrial RS-485 Field Bus, Point-to-Point RS-422 Link, Factory Automation Controller, Building Control Network, Data Acquisition Instrument, Telemetry and Remote Equipment.
Industrial RS-485 Field Bus
The ISL83491IP fits industrial RS-485 field-bus interfaces because it combines a differential driver and receiver at a 3.3 V supply while supporting high-speed and slew-rate-limited operating modes. The 14-pin through-hole package is particularly useful when maintaining existing controller cards, remote I/O modules, or production-test fixtures. Designers can use the driver-enable and receiver-enable functions to control bus direction and avoid unwanted transmitter activity. Slew-rate-limited operation can reduce high-frequency emissions on longer industrial cables, although the final rate must be checked against cable length and topology. The 3.3 V rail also simplifies integration with modern UART-based controllers.
Inirekomenda
Point-to-Point RS-422 Link
The ISL83491IP supports full-duplex point-to-point RS-422 links through its independent differential driver and receiver paths. This arrangement is useful for connecting a controller to a remote encoder, data logger, position sensor, or test instrument over balanced cabling. A 3.3 V supply suits modern embedded systems, while the leaded DIP package simplifies assembly and rework in industrial control hardware. Separate termination at the receiver is generally required according to the system impedance and cable length. The 14-pin footprint also leaves the circuit compatible with established through-hole RS-422 boards, reducing the mechanical changes required during modernization.
Inirekomenda
Factory Automation Controller
The ISL83491IP is appropriate for factory automation controllers that exchange commands and diagnostic data with distributed equipment over balanced wiring. Its 3.3 V operation can be shared with the controller's digital logic, while the RS-485/RS-422 capability supports both multidrop field buses and isolated point-to-point links. The through-hole 14-pin package is advantageous for ruggedized legacy platforms, maintenance controllers, and manually assembled test equipment. Slew-rate-limited mode should be considered where reducing edge-related EMI is important around motors, contactors, and switching power supplies. Cable routing, common-mode grounding, and bus termination remain essential to preserve differential signal integrity.
Inirekomenda
Building Control Network
The ISL83491IP can connect building-control equipment such as sensor nodes, room controllers, HVAC interfaces, and supervisory panels using an RS-485 or RS-422 backbone. Its 3.3 V supply requirement supports low-voltage embedded control boards, and the through-hole package suits controller products assembled in moderate volumes. The device's selectable operating approach allows slow, slew-limited communication where EMI control is more important, or high-speed operation where update latency and protocol throughput take priority. In a building installation, the design should include protective grounding, appropriately placed termination, and suitable surge protection while keeping the transceiver interface consistent with the selected bus topology.
Inirekomenda
Data Acquisition Instrument
The ISL83491IP is useful in data-acquisition instruments that must communicate with remote sensors or laboratory equipment over a balanced bus. The separate receiver and driver support RS-422-style point-to-point collection links, while the 3.3 V supply can simplify connection to FPGA- or MCU-based measurement systems. A 14-pin DIP package remains practical for laboratory instruments, interface cards, and service modules that favor through-hole assembly. Signal integrity depends on controlled grounding and termination, especially when cables pass near switching regulators or high-current laboratory equipment. The transceiver should be paired with suitable protection and filtering when external cables expose the board to conducted noise or ESD events.
Inirekomenda
Telemetry and Remote Equipment
The ISL83491IP fits remote telemetry equipment that must return sensor information over an industrial balanced link. Its 3.3 V operation is compatible with low-power embedded controllers, and the driver and receiver enable controls help manage half-duplex RS-485 traffic efficiently. The leaded DIP package supports equipment requiring field-serviceable through-hole construction or use in ruggedized legacy platforms. For long cables, the interface should be evaluated for maximum data rate, termination placement, common-mode range, and EMI susceptibility. Slew-rate-limited mode can provide a more gradual transition and lower emissions, but the protocol's required throughput must still be met. Protection components should be selected for the actual cable environment and grounding arrangement.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ISL83491IP — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Renesas Electronics |
| Package | 14-pin PDIP |
| Product Type | 1/1 RS-485/RS-422 transceiver |
| Supply Voltage | 3 V to 3.6 V |
| Nominal Supply | 3.3 V |
| Technology | BiCMOS |
| Operating Mode | High-speed or slew-rate-limited |
| Operating Temperature | -40 °C to +85 °C |
| Mounting Type | Through-hole |
Pangunahing mga Pagkakaiba
- Through-hole package preserves 14-pin DIP PCB compatibility (kumpara saMAX3491CSD+T)
- Supports both communication rate and EMI-conscious operating styles (kumpara saISL83491IBZ-T)
- Single-transceiver integration reduces parallel component count (kumpara saMAX3491ESD+)
Talaan ng Disenyo
Do not substitute a surface-mount transceiver without redesigning the PCB. The ISL83491IP uses a 14-pin PDIP footprint, while ISL83491IBZ-T, MAX3491CSD+T, and MAX3491ESD+ use small-outline packages. Even if a substitute has similar voltage and data-rate ratings, a mechanical adapter or new layout is required. After any replacement, verify every enable pin, supply pin, driver output, receiver input, and exposed interface connection rather than relying only on the transceiver description.
Apply termination according to the selected topology. A multidrop RS-485 bus normally places termination across the differential pair at both physical ends, whereas RS-422 point-to-point links commonly terminate at the receiver. Avoid placing unnecessary termination on every node because it can excessively load the bus. Confirm cable impedance, length, node count, logic thresholds, and data rate together; a nominal termination value is not sufficient if the complete wiring topology creates an excessive load.
Choose high-speed operation only when the required throughput justifies its edge rate. Slew-rate-limited operation can reduce high-frequency harmonics and radiated EMI, which is valuable near switching regulators, motors, and long cables. Keep the transceiver away from high-current switching nodes, provide a solid ground reference, and route the balanced pair together. External protection may be required for cable-connected ports, but its capacitance and clamping behavior should be checked against the intended data rate.
Impormasyon ng Pagsunod sa Kautusan
The available product information does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.