Renesas Electronics

ISL8485CB-T - 5V RS-485/RS-422 Transceiver | Renesas

MPN: ISL8485CB-T ✓ Nakahanda
5 V Vdss 8-pin SOIC, 0.154 inch (3.90 mm) width Package
MOQ: 1 |

ISL8485CB-T Ulas

The Renesas Electronics ISL8485CB-T is a 5 V, low-power RS-485/RS-422 line transceiver packaged in an 8-pin SOIC. It supports data rates up to 5 Mbps, operates from a 4.5 V to 5.5 V supply, and presents one unit load to an RS-485 bus. The device combines one driver and one receiver in a half-duplex transceiver arrangement for balanced industrial communication links.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals between a host controller and a differential communication bus. The driver transmits complementary differential signals, while the receiver detects the voltage difference across the pair. As a single-channel half-duplex transceiver, the ISL8485CB-T supports one communication line while sharing the same package and bus connection structure used by related ISL8485 devices.

The family is specified for 10% supply tolerance, providing a 4.5 V to 5.5 V operating range. Its BiCMOS construction supports low power consumption while operating at rates up to 5 Mbps. The ISL8485CB-T also provides ESD-protected, single-driver, single-receiver operation, making it suitable for point-to-point RS-422 links and multidrop RS-485 networks that require compact, surface-mount transceivers.

Renesas describes the ISL8485 family as a collection of 5 V-powered RS-485 and RS-422 transceivers. The CBZ-T ordering code is associated with a lead-free and RoHS-compliant version, while the CB-T designation identifies the tape-and-reel ordering configuration used in this listing. The 8-pin SOIC package supports conventional surface-mount assembly and is compatible with compact industrial and embedded control equipment.

Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, and embedded systems communicating over long differential cable runs. The 5 Mbps maximum data rate supports moderately high-speed control and data traffic, while the one-unit-load bus loading helps preserve network capacity when multiple transceivers share a bus.

PCB design should account for the difference between supply current and bus return current. Place the transceiver close to the connector and transceiver protection network, keep the differential pair routed as a tightly coupled pair, and provide the supply bypass capacitance recommended by the manufacturer. The 8-pin SOIC footprint should be checked against the PCB library before substitution because narrow-body variants can differ in lead width and courtyard dimensions.

This product page combines the manufacturer family description, distributor package and ordering information, current sourcing records, interface characteristics, and practical replacement guidance. It also distinguishes the exact ISL8485CB-T ordering code from related ISL8485 variants so engineers can evaluate footprint, supply, ESD, and rate requirements before approving a replacement.

Mga alternatibo na pwedeng ilagay na ISL8485CB-T — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

ISL8485IBZ-T

✅ Drop-In
📦 8-pin SOIC
Same narrow 8-SOIC package and single RS-485/RS-422 transceiver function; output drive and edge-rate characteristics require datasheet confirmation

📋 Alternatibo na Reference (hindi sa katalogo)

ISL8485EIBZ-T

✅ Drop-In
📦 8-pin SOIC
Same narrow 8-SOIC package, 5 V single-transceiver architecture, and RoHS-compliant lead-free construction; drive strength and slew-rate details differ by suffix

📋 Alternatibo na Reference (hindi sa katalogo)

ISL8485CBZ-T

✅ Drop-In
📦 8-pin SOIC
Same ISL8485 family, 5 V single-transceiver function, and 8-SOIC footprint; ordering suffix and qualification details differ

📋 Alternatibo na Reference (hindi sa katalogo)

ISL8485CB-T Mga Spesipikasyon

Product Type RS-485/RS-422 line transceiver
Volte ng Pagbibigay 5 V
Operating Supply Range 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps
Driver Count 1 driver
Receiver Count 1 receiver
Duplex Configuration Half-duplex
RS-485 Bus Loading 1 unit load
Process Technology BiCMOS
ESD Protection ±15 kV
Packhaging 8-pin SOIC, 0.154 inch (3.90 mm) width
Uri ng Pagpapasok Surface Mount
Ordering Package Tape & Reel
Tindminan RoHS Compliant
Katayuan ng Lifecycle Active

Gabay sa Pin Configuration ng ISL8485CB-T tape & reel

Pin configuration para sa ISL8485CB-T (tape & reel package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng tape & reel package para sa ISL8485CB-T

Wala ng detalyadong pinout data na magagamit para sa ISL8485CB-T.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

ISL8485CB-T ay nararapat para sa 6 aplikasyons: Industrial RS-485 Control Networks, Point-to-Point RS-422 Links, Building and Automation Controllers, Factory Automation Equipment, Test and Measurement Instrumentation, Embedded Serial Gateways.

🏭

Industrial RS-485 Control Networks

The ISL8485CB-T fits industrial control networks that require a compact 5 V differential interface and communication rates up to 5 Mbps. Its single driver and receiver form a half-duplex channel, while the documented one-unit-load bus loading helps preserve capacity in multidrop RS-485 systems. Place the transceiver between the controller UART and the protected bus connector, then use matched differential routing for the cable connection. Because the device is specified for a 4.5 V to 5.5 V supply range, the design must maintain that range during startup and bus faults. Termination, fail-safe biasing, and isolation strategy remain application-level choices rather than functions established by the transceiver itself.

🌐

Point-to-Point RS-422 Links

The ISL8485CB-T is appropriate for point-to-point RS-422 links where separate differential driver and receiver functions communicate over balanced cabling. Its 5 Mbps maximum data rate accommodates supervisory, data acquisition, and equipment-control traffic when cable length and loss permit. The 8-pin SOIC package preserves a conventional surface-mount footprint and supports compact interface sections. In a point-to-point circuit, retain the full-duplex benefit of separate transmit and receive paths and provide termination at the appropriate cable endpoints. Validate signal polarity, idle state, and receiver enable requirements against the exact ISL8485CB-T pin description before finalizing the schematic.

🧩

Building and Automation Controllers

The ISL8485CB-T can connect an embedded controller to building-automation equipment operating on an RS-485 bus. Its one-unit-load presentation is valuable when floor controllers, sensors, and gateways share a wired communication backbone. The 5 V transceiver core integrates neatly with low-voltage control logic, while the 8-pin SOIC package supports compact, high-density boards. Designers should separate the transceiver's clean supply path from noisy actuator circuits and route the differential pair away from switching nodes. A surge-protection network at the external connector should be selected for the installation's ESD and lightning exposure, with its effect on bus rise time and data rate reviewed before implementation.

🏭

Factory Automation Equipment

The ISL8485CB-T supports factory-automation modules that exchange commands and diagnostics with remote actuators, sensors, and motor controllers. Its 5 Mbps capability is useful for service data and fast control traffic on appropriately short and properly terminated buses, while the one-unit-load bus presentation allows additional nodes to participate. Position the transceiver near the field connector so transient-energy protection can be placed ahead of the sensitive IC. Keep the differential route paired and controlled over the distance where possible. The principal trade-off is that a half-duplex single-channel transceiver needs a defined direction-control strategy, so firmware and schematic logic must avoid simultaneous transmission and receiver conflicts.

⚡

Test and Measurement Instrumentation

The ISL8485CB-T is useful in laboratory and field-test instruments that need a compact, high-speed differential link between a controller and remote fixture. Its 8-pin SOIC package simplifies assembly on mixed-signal boards, and the 4.5 V to 5.5 V range accommodates common 5 V instrument architectures. Differential routing helps reject common-mode noise present near motors, relays, and switching power stages. When integrating the device into high-accuracy equipment, compare the transceiver's receive threshold and switching behavior with the measurement bandwidth. The bus interface improves communication integrity, but it does not replace isolation, shielding, or grounding required by sensitive analog front ends.

📡

Embedded Serial Gateways

The ISL8485CB-T bridges a low-voltage embedded UART to a legacy RS-485 or RS-422 field bus in industrial gateways and remote terminal units. Its 5 Mbps capability supports high-throughput firmware transfer and burst data transfer, while the compact 8-pin SOIC package leaves board area for other interface functions. The one-unit-load characteristic helps when multiple field devices share a segment. Implement a deterministic direction-control circuit or firmware state machine, and define behavior when the bus is idle, shorted, or undriven. External protection should be referenced to the transceiver ground strategy to prevent fault energy from propagating into the controller section.

What is the ISL8485CB-T?
The ISL8485CB-T is a 5 V, half-duplex RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. According to the Renesas ISL8485 product description, the family operates from 4.5 V to 5.5 V, supports data rates up to 5 Mbps, and presents one unit load to an RS-485 bus. The CB-T suffix identifies the tape-and-reel ordering configuration.
What are the key specifications of ISL8485CB-T that engineers should know?
The ISL8485CB-T combines a 4.5 V to 5.5 V supply range, a maximum data rate of 5 Mbps, one driver, one receiver, and an 8-pin SOIC package. Renesas describes the ISL8485 family as a BiCMOS, 5 V-powered RS-485/RS-422 transceiver family. It also presents one unit load to the bus, which is important when calculating how many transceivers can share the same RS-485 network.
Where can I download the ISL8485CB-T datasheet PDF?
The ISL8485CB-T datasheet is available through the Renesas ISL8485 product page and through the indexed Intersil PDF copy. The manufacturer part-details page is the preferred source because it keeps the document connected to the current product family. Search for the exact ISL8485CB-T ordering code and use the pin-description table in the manufacturer datasheet when assigning PCB connections.
Where can I find the ISL8485CB-T pinout?
The ISL8485CB-T pinout is defined in the manufacturer datasheet for the 8-pin SOIC package. Use that pin-description table to confirm driver, receiver, enable, ground, and supply assignments before routing a board. The indexed PDF identifies the ISL8485CB-T as a 16-page datasheet, while the family description confirms the device uses an 8-SOIC package.
What is the operating voltage of ISL8485CB-T?
The ISL8485CB-T operates from 4.5 V to 5.5 V, representing a nominal 5 V supply with a 10% tolerance range. This range is stated in the Renesas ISL8485 family description. Designers should keep the transceiver supply within those limits and account for noise, voltage drop, and startup behavior when determining whether 5 V system rails provide adequate margin.
What data rate does ISL8485CB-T support?
The ISL8485CB-T supports data rates up to 5 Mbps. Renesas states that the ISL8485, ISL8490, and ISL8491 families support rates up to 5 Mbps while using 5 V power. Actual system throughput can be lower because of bus length, transceiver propagation delay, cable loss, termination, grounding, and the selected data rate limit of the connected controller.
Is ISL8485CB-T suitable for RS-485 and RS-422 networks?
Yes, the ISL8485CB-T is intended for both RS-485 and RS-422 balanced communication. Renesas identifies the ISL8485 family as a single-channel transceiver compatible with both standards. RS-422 point-to-point links can use the differential driver and receiver directly, while RS-485 designs additionally require an appropriate bus topology, termination strategy, and bias arrangement.
ISL8485CB-T vs ISL8485IBZ-T - which is better for an RS-485 link?
The ISL8485CB-T and ISL8485IBZ-T are closely related Renesas ISL8485-family devices, and the available comparison identifies both as 5 V single transceivers in narrow 8-SOIC packages. Selection should therefore focus on the specific IBZ suffix characteristics, including its drive and slew-rate configuration, rather than assuming identical behavior. The exact manufacturer datasheet should be checked for enable, shutdown, and edge-rate differences.
When should I choose ISL8485CB-T over ISL8485EIBZ-T?
Choose the ISL8485CB-T when its CB-specific output and switching characteristics match the channel timing and signal-integrity requirements of the design. Choose the ISL8485EIBZ-T when its documented electrical characteristics, particularly its drive behavior, are preferable for the target bus. Both devices use the narrow 8-SOIC package according to component comparisons, but the suffix-specific datasheet remains the controlling document.
Can ISL8485EIBZ-T replace ISL8485CB-T?
The ISL8485EIBZ-T is a candidate drop-in replacement because both devices are listed as Renesas single transceivers in narrow 8-SOIC packages. Compatibility still requires confirmation of pin functions, driver strength, slew rate, receiver thresholds, enable behavior, and supply limits. Use the two manufacturer datasheets together before changing a qualified PCB or production assembly.
What can replace ISL8485CB-T?
The ISL8485IBZ-T and ISL8485EIBZ-T are the strongest documented same-brand replacements because they are listed in narrow 8-SOIC packages and are compared directly with the ISL8485CB-T. A valid replacement must preserve the 8-pin footprint, 5 V operation, driver/receiver functions, bus loading, and required data-rate and timing behavior. No cross-brand substitute should be approved without a separate pin and parametric review.
Is ISL8485CB-T the same as ISL8485CBZ-T?
The ISL8485CB-T and ISL8485CBZ-T refer to related ordering configurations within the same ISL8485 family, but they should not be treated as identical without checking the manufacturer ordering table. The comparison record identifies the EIBZ and CBZ variants as RoHS-compliant and lead-free, while the CB-T listing uses the tape-and-reel suffix. Verify the exact finish, tape orientation, and shipping form on the manufacturer page.
Where can I buy ISL8485CB-T and what is its price?
Use the Request a Quote form on this page to request current ISL8485CB-T availability, unit pricing, and lead time. Current inventory and transaction terms can change by quantity, date code, and package configuration, so a quote provides the appropriate purchasing record. The exact MPN shown in the request should be ISL8485CB-T, not the ISL8485CB or ISL8485CBZ-T ordering codes.
What is the lead time for ISL8485CB-T?
Current lead time for the ISL8485CB-T should be confirmed through the Request a Quote form on this page. The Renesas product page identifies the associated CBZ-T configuration as an active family member, while distributor records show market availability for exact and closely related order codes. Submit the required quantity and packaging information to obtain a dated sourcing commitment.
Is ISL8485CB-T in stock?
Stock status for the ISL8485CB-T can be requested through the Request a Quote form on this page. The available distributor records include an exact ISL8485CB-T listing, but inventory quantities can change rapidly and may differ by package form. Provide the required quantity, date-code preference, and target delivery schedule so the response reflects the current order configuration.
What compliance and lifecycle information applies to ISL8485CB-T?
The ISL8485CB-T belongs to an active Renesas product family, and the related CBZ ordering information identifies it as RoHS-compliant and lead-free. According to the Renesas family description, the device is a 5 V RS-485/RS-422 transceiver operating from 4.5 V to 5.5 V. The manufacturer product page should control final environmental, lifecycle, and orderable-part status.

Impormasyon ng Talumpati sa Engineering for ISL8485CB-T — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the ISL8485CB-T when the design requires a 5 V Renesas RS-485/RS-422 transceiver in an 8-pin SOIC and matches the exact CB ordering configuration already approved for the assembly. Choose the ISL8485CBZ-T when its associated ordering and environmental attributes are preferred for the procurement plan. Consider the ISL8485IBZ-T or ISL8485EIBZ-T when their suffix-specific drive strength, slew rate, enable behavior, or receiver characteristics better fit the channel. Before replacing the ISL8485CB-T, verify pin functions, 4.5 V to 5.5 V operation, 5 Mbps data-rate capability, one-unit-load bus presentation, and every electrical maximum and typical value. A shared SOIC footprint alone is not enough to approve a qualified design.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto ISL8485IBZ-T ISL8485EIBZ-T ISL8485CBZ-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 line transceiver RS-485/RS-422 transceiver
Supply Voltage 5 V 5 V 5 V 5 V
Operating Supply Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps 5 Mbps
Driver and Receiver Count 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver
Bus Loading 1 unit load 1 unit load 1 unit load 1 unit load

Pangunahing mga Pagkakaiba

  • Exact CB-family ordering configuration (kumpara saISL8485CBZ-T)
  • Same-package Renesas upgrade path (kumpara saISL8485EIBZ-T)
  • Direct family alternative with matching bus loading (kumpara saISL8485IBZ-T)

Talaan ng Disenyo

Route the RS-485 and RS-422 signals as a tightly coupled differential pair from the transceiver to the protection network and connector. Avoid crossing splits between the two conductors, keep the pair away from switching nodes and high-current paths, and minimize stub lengths. Use the package pin-description table in the manufacturer datasheet to preserve the intended pin assignments and maintain a consistent ground reference between the transceiver and protection devices.

Do not treat the CB-T, CBZ-T, IBZ-T, and EIBZ-T suffixes as interchangeable without checking the ordering table and electrical characteristics. The narrow 8-SOIC footprint may appear compatible, but driver strength, slew rate, enable behavior, receiver thresholds, and qualification can vary. Before substitution, compare the exact manufacturer datasheets and confirm that the replacement retains the required 4.5 V to 5.5 V supply range, data-rate capability, and bus loading.

Place a suitable protection network at the external connector and connect it to the transceiver's defined ground strategy. Select components so that protection capacitance does not distort the intended edge rate or violate the receiver's common-mode limits. For factory and building installations, evaluate the ESD and surge environment separately because a connector-side protection network may require coordination with cable shielding, chassis grounding, and isolated systems.

Keep the 5 V transceiver supply within 4.5 V to 5.5 V and decouple it close to the IC. The transceiver supply current is distinct from the current delivered through the communication bus, so supply sizing should account for both internal consumption and external loads. Review whether the 5 V rail experiences startup droop or switching noise from nearby actuators, and avoid routing the bus return through a high-impedance logic-ground path.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Yes
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The ISL8485EIBZ-T comparison identifies the related Renesas variant as RoHS-compliant and lead-free. The ISL8485CB-T exact ordering code should be confirmed against the manufacturer ordering table for its final environmental status.

Kaugnay na Hanapin

ISL8485CB-T datasheet ISL8485CB-T pinout ISL8485CB-T datasheet pdf Renesas ISL8485CB-T ISL8485CB-T equivalent ISL8485CB-T replacement ISL8485CB-T cross reference ISL8485CB-T vs ISL8485IBZ-T ISL8485CB-T 8-SOIC footprint ISL8485CB-T 5 Mbps RS-485 ISL8485CB-T RS-422 application circuit ISL8485CB-T price ISL8485CB-T stock ISL8485CB-T lead time

Mga kaugnay na Mga Komponente at mga Tuntunin

Renesas Electronics ISL8485CB-T ISL8485CB ISL8485CBZ-T ISL8485IBZ-T ISL8485EIBZ-T RS-485 RS-422 half-duplex transceiver differential line transceiver interface IC BiCMOS 5 V transceiver 4.5 V to 5.5 V supply 5 Mbps data rate one unit load 8-pin SOIC SOIC family surface mount ESD protection industrial communication factory automation building automation embedded serial gateway
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ