KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip
料号: KSZ8795CLXIC ✓ 量产中KSZ8795CLXIC 概述
An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between multiple physical ports using a MAC address table. In this device family, the switch also integrates 10/100BASE-T/TX PHYs with internal biasing resistors, on-chip termination and auto-negotiation, so a single silicon device replaces discrete magnetics-heavy copper PHY circuitry. The KSZ8795CLXIC therefore sits in the hierarchy: Ethernet switch > Layer 2 managed switch > integrated copper PHY switch > network interface IC.
Key features include four 10/100Mbps copper ports with auto-MDIX support, a Gigabit-capable uplink port, IEEE 802.3u compliant operation, MIIM and SPI management interfaces, and on-chip port termination that eliminates external resistor networks. Low power consumption is achieved through internal biasing rather than external resistor dividers, and the small package outline reduces board area versus discrete implementations.
Internally the device combines a five-port frame buffer with an integrated 10/100 MAC/PHY per copper port and a configurable uplink MAC supporting GMII, RGMII, MII and RMII. Management is handled by a MIIM register interface and an SPI host interface, giving the system processor access to VLAN, QoS, port enable and mirror registers. The design is intended for cost-sensitive embedded equipment where a single high-integration switch replaces several discrete PHYs and magnetics.
Typical applications include industrial control gateways, industrial Ethernet switches and PLC communication modules, IP cameras and surveillance recorders, industrial IoT and building-automation nodes, and consumer or telecom CPE equipment with a Gigabit uplink. The configurable uplink lets one design serve either RGMII-based application processors or RMII-based microcontrollers.
Keep the analog and digital ground pins tied to a single solid, contiguous ground plane. Microchip explicitly warns that splitting GDNA and GNDD into separate planes causes frame drops, so route both to the same uninterrupted system ground and place the port magnetics with short, tightly-coupled differential pairs to preserve return-path integrity.
This page combines the manufacturer switch specifications, distributory pricing structure, pin-compatible 80-LQFP alternatives, and practical layout and thermal guidance that you would otherwise have to reconstruct from several separate documents.
直接替换替代料: KSZ8795CLXIC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
KSZ8765CLX
✅ 直接替换📋 参考替代料(不在目录中)
KSZ8765CLXIC
✅ 直接替换联系询价
查看数据手册 →KSZ8795CLX
✅ 直接替换📋 参考替代料(不在目录中)
KSZ8795CLXIC 最大额定值与电气特性
| Device Type | Integrated Layer 2 managed 5-port 10/100 Ethernet switch with Gigabit uplink |
| Number of Ports | 5 (Ports 1-4 copper 10/100Mbps, Port 5 uplink) |
| Copper Port Speed | 10/100 Mbps per port (Ports 1-4) |
| Uplink Port Speed | 10/100/1000 Mbps (Port 5) |
| Host Interface Options | GMII, RGMII, MII, RMII (configurable on Port 5) |
| Management Interface | MIIM register access and SPI host interface |
| 电源电压 | 3.3 V |
| 封装 | 80-LQFP (10 x 10 mm) |
| 安装类型 | Surface Mount |
| On-Chip Features | Internal biasing, on-chip termination, internal PHY |
| Power Consumption | Lowest power consumption in class via internal biasing |
| Ethernet Compliance | IEEE 802.3u 10BASE-T/100BASE-TX |
| Ethernet Media Features | 10/100BASE-T/TX PHY with auto-MDIX |
| Ordering Code Suffix | IC = industrial temperature, tray packaging |
| RoHS 状态 | RoHS Compliant |
| 生命周期状态 | Active |
| Datasheet Document Number | 00002112B |
| Datasheet Length | 132 pages |
| Hardware Design Checklist Document | KSZ8795CLX Hardware Design Checklist, document 00003579B |
KSZ8795CLXIC 80-lqfp (10 x 10 mm) 引脚配置指南
KSZ8795CLXIC(80-lqfp (10 x 10 mm) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: KSZ8795CLXIC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
KSZ8795CLXIC 适用于 6 应用s: Industrial Ethernet Switch and Gateway, IP Camera and Surveillance Network Node, Industrial IoT and Building Automation Node, Consumer and Telecom Customer Premises Equipment, Embedded Linux SoC Network Interface, PLC and Programmable Controller Communication Module.
Industrial Ethernet Switch and Gateway
The KSZ8795CLXIC suits industrial gateways that must aggregate four 10/100Mbps field devices onto a Gigabit backbone. Ports 1 through 4 provide 10/100BASE-T/TX copper with integrated PHY, internal biasing and on-chip termination, which removes the external resistor dividers and termination networks that dominate the BOM of discrete copper PHY designs. Port 5 can be configured for RGMII, GMII, MII or RMII, so a single board layout can accept either an industrial application processor or a microcontroller host. Because the device is a managed Layer 2 switch, the host processor can read and write VLAN, QoS, port enable and mirroring registers over SPI or MIIM, which shortens commissioning time in a plant network.
推荐
IP Camera and Surveillance Network Node
An IP camera with several downstream sensors and a single uplink fits the KSZ8795CLXIC architecture exactly: four copper ports attach the camera, encoder and storage nodes while Port 5 carries video traffic upward at Gigabit speed. The 80-LQFP (10 x 10 mm) package keeps the switch footprint small enough for compact camera boards, and the 3.3 V single supply shares rails with typical video SoCs. Managed Layer 2 features let the system prioritize frames with QoS, and the port-mirror registers support remote diagnostics without extra instrumentation. On-chip termination means the board needs fewer passive parts beside each RJ-45 magnetic module, helping meet the tight cost and area budgets of volume surveillance designs.
推荐
Industrial IoT and Building Automation Node
Building automation controllers and industrial IoT edge nodes typically need several low-speed copper devices on one board and one fast link to a supervisory controller. The KSZ8795CLXIC assigns Ports 1 through 4 to sensors, actuators and HMI panels while Port 5 handles the uplink, and the configurable RGMII or RMII host interface matches both high-end and microcontroller-class processors. Managed Layer 2 forwarding with QoS prioritization keeps time-sensitive control traffic ahead of bulk data, and the MIIM/SPI management path lets the host apply VLAN segmentation between building floors. Low power consumption and on-chip biasing reduce both board area and the passive part count on space-constrained DIN-rail modules.
推荐
Consumer and Telecom Customer Premises Equipment
Customer premises equipment such as set-top boxes, home gateways and access terminals often needs to bridge several internal Ethernet PHY ports to an external network port. The KSZ8795CLXIC gives four 10/100Mbps internal copper ports and a configurable Gigabit uplink on a single 3.3 V device, keeping the bill of materials and board area low compared with using discrete PHY chips plus a separate switch. Internal biasing and on-chip termination remove resistor networks from every port, which shortens the analog design cycle and reduces EMC troubleshooting. Because the switch is managed, the host can enable or disable ports, set rate limits and mirror traffic for diagnostics, which supports remote fault isolation in deployed CPE installations.
推荐
Embedded Linux SoC Network Interface
Embedded Linux boards frequently run an application processor with an RGMII interface and need to expose additional Ethernet ports for cameras, storage and debug links. The KSZ8795CLXIC lets the same silicon present a Gigabit RGMII uplink to the SoC while four 10/100 ports serve local peripherals, and the SPI management path gives the Linux driver direct register access for link configuration. The 10 x 10 mm 80-LQFP outline is compatible with the density of compact single-board computers, and the single 3.3 V rail matches typical SoC core supplies, simplifying power sequencing. Layer 2 management registers also let the driver implement bridging or VLAN tagging for multi-homed embedded systems.
推荐
PLC and Programmable Controller Communication Module
Programmable controller communication modules need a rugged, self-contained Ethernet interface that supports several devices on the same board and one uplink to the plant network. The KSZ8795CLXIC provides four 10/100Mbps copper ports with integrated PHY and on-chip termination plus a configurable GMII/RGMII/MII/RMII uplink, letting the module connect an Ethernet switch, an HMI and remote I/O while still reaching a Gigabit controller. Managed Layer 2 operation supports port mirroring for commissioning diagnostics, and the MIIM/SPI interface lets the PLC CPU read link and error counters without extra external hardware. The single 3.3 V supply and compact 80-LQFP footprint integrate cleanly into tightly budgeted control module boards.
推荐
推荐产品汇总
工程参考数据: KSZ8795CLXIC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | KSZ8765CLX | KSZ8765CLXIC | KSZ8795CLX |
|---|---|---|---|---|
| Package | 80-LQFP (10 x 10 mm) | 80-LQFP (10 x 10 mm) - same | 80-LQFP (10 x 10 mm) - same | 80-LQFP (10 x 10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Total Port Count | 5 | 5 | 5 | 5 |
| Copper Port Speed (Ports 1-4) | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| Uplink Port Speed (Port 5) | 10/100/1000 Mbps | 10/100 Mbps (no Gigabit uplink) | 10/100 Mbps (no Gigabit uplink) | 10/100/1000 Mbps |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Integrated Biasing and Termination | Yes, internal biasing with on-chip termination | Yes | Yes | Yes |
| Pin Compatibility | Reference design | Pin-compatible, same 80-pin LQFP package | Pin-compatible, same 80-pin LQFP package | Identical silicon and footprint |
关键差异点
- Gigabit-capable uplink in the same 80-LQFP footprint (对比 KSZ8765CLX)
- Higher integration reduces external passive count (对比 KSZ8765CLXIC)
- Single-part 5-port managed switch with host-side flexibility (对比 KSZ8795CLX)
设计说明
Tie GDNA and GNDD together into a single solid, contiguous system ground plane. Microchip explicitly warns that separate analog and digital ground regions cause frame drops on KSZ8795CLX designs because the return current must then find a path between the two domains under the device. Route the copper port differential pairs as short, tightly coupled traces with a continuous ground reference directly beneath them, and place the isolation magnetics close to the RJ-45 connectors to minimize radiated emissions.
Follow the KSZ8795CLX Hardware Design Checklist (document 00003579B) for new boards. The switch already integrates internal biasing and on-chip termination, so do not add external bias resistor dividers or termination networks on Ports 1 to 4. Provide the standard decoupling close to the 3.3 V supply pins, and keep the RGMII/GMII clock and data routing short and impedance controlled because the uplink runs at 1.25 GB/s in RGMII mode, where setup and hold margins are tight.
Estimated: with a 3.3 V supply and a full 100 Mbps load on all five ports, the switch dissipation scales with port activity; allow for roughly 1 W to 2 W of internal consumption in the worst case, which means the 80-LQFP package needs a solid copper pour and, in a sealed enclosure, careful attention to ambient rise. Estimate your own figure from the measured per-port current in the datasheet operating tables multiplied by the number of active ports, then verify junction temperature against the maximum rating in the device documentation.
The Port 5 uplink is configurable, so fix the host interface mode in software before layout sign-off, because GMII, RGMII, MII and RMII use different clock and data topologies. RGMII requires a 1.25 GB/s interface with source-synchronous clocking and careful trace length matching between the clock and data pairs; RMII uses a slower 50 MHz reference clock with a narrower timing budget. Confirm the selected mode and the corresponding host-side PHY or SoC timing in the datasheet before finalizing the layout.
Do not assume the base KSZ8795CLX and KSZ8795CLXIC are interchangeable without checking the temperature code and shipping format, since the IC suffix denotes the industrial tray ordering code. Likewise, verify that the link partner on each copper port supports auto-MDIX before relying on it, and confirm that the uplink speed negotiation on Port 5 is enabled in the boot configuration. Finally, remember that Microchip states there is currently no exact drop-in replacement for this device in the portfolio, so plan availability around the pin-compatible KSZ8765CLX family.
合规信息
RoHS compliant status is shown on aggregator part listings for KSZ8795CLXIC. The IC ordering suffix denotes the industrial temperature grade; automotive AEC-Q100 qualification is not indicated for this Ethernet switch.