LM224DG4 - Quad General-Purpose Op Amp | Texas Instruments
MPN: LM224DG4 ✓ NakahandaLM224DG4 Ulas
An operational amplifier is a voltage-gain device that uses differential feedback to amplify the difference between two input voltages. The LM224DG4 belongs to the operational-amplifier hierarchy, combining four high-gain, internally compensated amplifier channels in one integrated circuit. This quad-channel arrangement is useful when a system needs several closely related signal-processing stages, such as sensor conditioning, active filtering, or buffering multiple analog channels.
The principal benefit of the four-channel architecture is board-space efficiency. Instead of placing four separate single op amps on a PCB, a designer can use one 14-SOIC device and distribute the amplifier channels according to signal flow. The standard general-purpose classification makes the LM224DG4 appropriate for non-specialized analog functions, although precision requirements should be checked against the manufacturer's electrical characteristics before selecting it for high-accuracy instrumentation.
The wide 3 V to 32 V operating range provides flexibility for industrial, instrumentation, sensing, and test-equipment designs. Operation from a single positive supply simplifies circuits where the signal is referenced to ground, while split supplies can support bipolar signal processing. Because four amplifiers share one package, power-supply routing and decoupling must be designed to keep common supply impedance and package-level heating low.
Typical uses include sensor-interface amplifiers, low-frequency active filters, analog signal conditioners, transducer amplifiers, sample-and-hold support circuits, and general-purpose buffers. The LM224DG4 is especially useful when multiple amplifier channels are required but the precision, speed, noise, or rail-to-rail performance of a specialized amplifier is not required.
Designers should verify input common-mode range, output swing, supply current, slew rate, and stability requirements against the Texas Instruments LM224 product documentation. Place the package power pins and bypass capacitor according to the datasheet guidance, maintain adequate operating area for thermal dissipation, and avoid relying on rail-to-rail operation unless the selected grade explicitly supports it.
This product page combines package information, application guidance, drop-in replacement analysis, comparison parameters, and practical layout notes. It is intended to accelerate engineering selection while directing detailed verification to the manufacturer datasheet and pin-description tables.
Mga alternatibo na pwedeng ilagay na LM224DG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM224DG4 (parehas na form factor at footprint) — pagkakaiba sa Package, Amplifier Type, Number of Amplifier Circuits, AEC-Q100 Qualification, Product Type.
LM224KAD
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM224DR
✅ Drop-In✓ Sa Stock
$0.1641 / Yunit
Tingnan ang Datasheet →LM224KD
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324DG4
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →LM2902DG4
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →LM224DG4 Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Quadruple operational amplifier |
| Amplifier Circuit Count | 4 circuits |
| Operating Supply Voltage Range | 3 V to 32 V |
| Packhaging | 14-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Device Class | Standard general-purpose amplifier |
| Number of Amplifiers | 4 |
| Supply Configuration | Single or split supply |
Pin Configuration ng LM224DG4
| Pin 1 | OUT1 — Output of amplifier channel 1 |
| Pin 2 | IN1- — Inverting input of amplifier channel 1 |
| Pin 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Pin 4 | V- — Negative power supply connection |
| Pin 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Pin 6 | IN2- — Inverting input of amplifier channel 2 |
| Pin 7 | OUT2 — Output of amplifier channel 2 |
| Pin 8 | OUT3 — Output of amplifier channel 3 |
| Pin 9 | IN3- — Inverting input of amplifier channel 3 |
| Pin 10 | IN3+ — Non-inverting input of amplifier channel 3 |
| Pin 11 | V+ — Positive power supply connection |
| Pin 12 | IN4- — Inverting input of amplifier channel 4 |
| Pin 13 | IN4+ — Non-inverting input of amplifier channel 4 |
| Pin 14 | OUT4 — Output of amplifier channel 4 |
Tipikal na mga Gamit
LM224DG4 ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Active Filters and Audio Control, Test and Measurement Instrumentation, Battery-Powered Monitoring Devices, Interface Buffering and Level Conversion, Power Supply Monitoring and Control Loops.
Industrial Sensor Signal Conditioning
The LM224DG4 fits industrial sensor-conditioning circuits that require several amplifier stages within one 14-pin SOIC package. Its four amplifier channels can provide non-inverting gain, inverting gain, buffering, and level conversion around sensors such as temperature, pressure, and position transducers. The 3 V to 32 V supply range supports both low-voltage electronics and 24 V industrial systems. Designers should verify the sensor’s output range against the input common-mode limits, confirm adequate output swing, and check the amplifier grade’s operating-temperature range before production release.
Active Filters and Audio Control
The four-channel LM224DG4 can implement low-frequency active filters, tone-control stages, and general audio signal-conditioning paths without requiring four separate packages. Feedback networks determine the closed-loop response, while the shared quad-device construction simplifies routing between adjacent filter stages. The broad 3 V to 32 V supply capability accommodates multiple analog rails, but the selected circuit must stay within the amplifier’s common-mode range and output-swing limits. Check gain-bandwidth and slew-rate requirements against the manufacturer’s typical curves for the exact LM224 grade.
Test and Measurement Instrumentation
LM224DG4 is useful in general-purpose test and measurement front ends where four buffered or amplified channels are required. Possible uses include sensor conditioning, differential-to-single-ended conversion, reference buffering, and gain stages around measurement bridges. Its 14-pin SOIC package reduces board area, while the wide 3 V to 32 V supply range supports bench and industrial instrumentation power systems. Precision designs should check input offset, bias current, noise, and drift against the requirements of the measurement rather than treating the general-purpose amplifier as automatically precision-qualified.
Battery-Powered Monitoring Devices
The LM224DG4 can serve as the analog amplification core in battery-powered environmental monitors, portable meters, and sensor interfaces. Four channels allow the device to support several sensor paths while sharing one package and supply rail. The LM224 family’s 3 V minimum supply rating supports common single-cell and multi-cell operating ranges, but total quiescent current contributes directly to battery life. Confirm channel-current consumption, output load capability, and low-voltage behavior in the manufacturer datasheet, then select output values that avoid forcing the amplifier into nonlinear operation.
Interface Buffering and Level Conversion
The LM224DG4 can buffer sensor outputs before they enter an ADC or microcontroller input and can perform voltage-level shifting where the source and destination limits are compatible with the amplifier’s input and output ranges. Quad-channel availability is valuable in multiplexed measurement systems where several analog lines require buffering. The device should not automatically be used as a logic-level translator without checking common-mode limits, output swing, and source impedance. Place short, quiet input routes and provide local supply bypassing to prevent added noise or instability.
Power Supply Monitoring and Control Loops
The LM224DG4 can implement amplifier-based monitoring, threshold comparison, and error-amplifier functions in 24 V industrial or control systems because its operating supply range extends to 32 V. Multiple channels can monitor separate rails or assist with feedback and fault handling. The output must remain inside the allowed swing, and any comparator-style configuration requires the correct polarity and feedback arrangement. Designers should also account for the four amplifiers’ combined package dissipation, input common-mode limits, and stability requirements rather than evaluating only one channel in isolation.
Impormasyon ng Talumpati sa Engineering for LM224DG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM224KAD | LM224DR | LM224KD | LM324DG4 | LM2902DG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Amplifier Channel Count | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Device Class | Standard general-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Drop-In Compatibility | 14-pin SOIC LM224 reference device | Documented as completely replaceable | Same package family; grade verification required | Same package family; grade verification required | Same package and channel count; electrical verification required | Same package and channel count; electrical verification required |
Pangunahing mga Pagkakaiba
- Documented same-footprint replacement option (kumpara saLM224KAD)
- Quad-channel integration reduces package count (kumpara saLM324DG4)
- Wide operating supply range (kumpara saLM2902DG4)
Talaan ng Disenyo
Place the supply-bypass capacitor immediately adjacent to the LM224DG4 positive and negative supply pins, with the shortest practical ground return. Keep amplifier input routing away from supply, clock, and switching-node traces because input capacitance combined with feedback resistance can amplify coupling into an analog signal. Use a solid ground plane and provide separate copper areas for sensitive inputs and outputs when the circuit handles low-level signals.
Calculate dissipation from the total voltage drop across all four channels and the total supply current rather than evaluating one amplifier in isolation. Four channels can create package-level heating even when each channel appears lightly loaded. Confirm the maximum supply, output swing, and channel-current limits in the manufacturer datasheet, and provide adequate copper area so the SOIC package does not become the thermal bottleneck.
Do not treat a 32 V supply rating as a 32 V signal-swing rating. Input common-mode voltage and output swing are separate electrical limits, especially with a single positive supply. Similarly, a pin-compatible replacement is only electrically interchangeable after its input range, offset, bias current, bandwidth, slew rate, noise, stability, and temperature grade have been compared. Use the exact ordering-code datasheet for final sign-off.
Impormasyon ng Pagsunod sa Kautusan
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the exact LM224DG4 ordering code.