STMicroelectronics

LM258AWDT - Dual 30V Low-Power Op Amp | STMicroelectronics

MPN: LM258AWDT ✓ Nakahanda
3 V to 30 V Vdss 60 mA Id 8-pin SOIC, 0.154 inch body width Package
MOQ: 1 |

LM258AWDT Ulas

The STMicroelectronics LM258AWDT is a dual general-purpose operational amplifier designed for low-power operation from a single 3 V to 30 V supply. It provides two amplifier channels in an 8-pin SOIC package, with input and output voltage ranges extending to ±1.5 V and ±15 V, respectively. Key characteristics include 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 20 nA input bias current, and up to 60 mA of output current per channel. The LM258AWDT is supplied in tape-and-reel packaging for automated assembly.

A general-purpose operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify a voltage difference. In the broader electronics hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories, where it supports sensor interfaces, buffer stages, error amplifiers, analog-to-digital converter drivers, and general feedback-control circuits. The LM258 family combines broad supply-voltage tolerance with low quiescent-current operation, making it useful where the signal level and supply voltage vary across industrial or automotive equipment.

The principal features of the LM258AWDT include two independent channels, a 3 V to 30 V operating range, 85 dB open-loop gain-bandwidth behavior, low 20 nA input bias current, and approximately 0.1 µA input offset current. Its 1.1 MHz gain-bandwidth product supports moderate-frequency signal amplification, while the 0.6 V/µs slew rate supports reasonably clean output transitions. A 60 mA per-channel output-current capability is useful for driving moderate loads and providing isolation between high-impedance sources and downstream circuitry.

The automotive “A” version is identified as AEC-Q100 qualified in the available component information. This qualification is meaningful in applications where operating temperature, shock, vibration, and extended-life reliability require controlled automotive qualification. Because it is a bipolar, low-power dual op amp, the LM258AWDT emphasizes supply flexibility and input-current behavior rather than rail-to-rail input or output operation. Its usable common-mode and output ranges therefore need to remain inside the limits specified by the manufacturer datasheet.

Typical applications include industrial sensor conditioning, battery-powered instrumentation, current-loop receivers, analog signal buffers, bridge-amplifier interfaces, and low-frequency control loops. Automotive electronics can use the qualified version where its operating and environmental ratings match the system requirements. Two channels can be used independently or together for differential, summing, instrumentation, or active-filter configurations, reducing the number of separate amplifier packages required on a board.

The main design consideration is rail-to-rail behavior. A circuit requiring input or output swing close to either supply rail may not be served by the LM258AWDT’s conventional common-mode range. Designers should also check output-current limits, load capacitance, supply ripple, feedback stability, and the minimum operating voltage for the selected gain configuration before finalizing the circuit.

This page combines the LM258AWDT’s principal electrical ratings, automotive qualification, package details, practical applications, same-footprint alternatives, and design guidance to support component selection, PCB planning, sourcing, and schematic review.

Mga alternatibo na pwedeng ilagay na LM258AWDT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok LM258AWDT (parehas na form factor at footprint) — pagkakaiba sa Gain-Bandwidth Product, Package.

Texas Instruments
Gain-Bandwidth Product: 700 kHz
Package: 8-pin SOIC
Ikabit sa LM258AWDT →

LM258AWYPT

✅ Drop-In
📦 8-SOIC
0% difference in the listed 1.1 MHz GBW, 0.6 V/µs slew rate, 20 nA input bias, 3-30 V supply, and 60 mA output ratings; order-code markings should still be checked

📋 Alternatibo na Reference (hindi sa katalogo)

LM258ADT

✅ Drop-In
📦 8-SOIC
Same 8-SOIC LM258 family and dual-amplifier arrangement; the comparison listing identifies no electrical difference, so the replacement floor is 70% pending order-code and pinout verification

📋 Alternatibo na Reference (hindi sa katalogo)

TSH22IDT

✅ Drop-In
📦 8-SOIC
Same 8-SOIC dual-op-amp footprint with up to 30% parameter tolerance used for the 70% match floor; the candidate listing requires explicit pinout and electrical validation

📋 Alternatibo na Reference (hindi sa katalogo)

TSB7192IDT

✅ Drop-In
📦 8-SOIC
Same 8-SOIC candidate package with up to 30% parameter tolerance used for the 70% match floor; the candidate listing requires explicit pinout and electrical validation

📋 Alternatibo na Reference (hindi sa katalogo)

LM258AD

✅ Drop-In
Texas Instruments
📦 8-SOIC
Dual operational amplifier · 2 circuits · 30 V · 700 kHz · 1.1 MHz · 100 dB · 500 uA · 20 nA

Magkontak para sa presyo

Tingnan ang Datasheet →

LM258AWDT Mga Pinakamataas na Rating at Electrical Characteristics

Amplifier Type General-purpose dual operational amplifier
Number of Channels 2 circuits
Supply Voltage Range 3 V to 30 V
Hanay ng Voltage ng Input ±1.5 V to ±15 V
Hanay ng Output Volte ±1.5 V to ±15 V
Output Current per Channel 60 mA
Input Bias Current 20 nA
Input Offset Current 0.1 µA
Gain-Bandwidth Product 1.1 MHz
Slew Rate 0.6 V/µs
Open-Loop Gain 85 dB
Kuru-kuryente ng Kapayapaan 0.1 µA per amplifier
Packhaging 8-pin SOIC, 0.154 inch body width
Package Dimensions 0.154 inch width × 3.90 mm length
Uri ng Pagpapasok Surface mount
Packaging Tape and reel
Automotive Qualification AEC-Q100 qualified

Gabay sa Pin Configuration ng LM258AWDT 0.154 inch width × 3.90 mm length

Pin configuration para sa LM258AWDT (0.154 inch width × 3.90 mm length package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 0.154 inch width × 3.90 mm length package para sa LM258AWDT

Wala ng detalyadong pinout data na magagamit para sa LM258AWDT.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

LM258AWDT ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Automotive Sensor Interface, Battery-Powered Instrumentation, Current-Loop Signal Receiver, Analog-to-Digital Converter Driver, Audio and Control Amplification.

🏭

Industrial Sensor Signal Conditioning

The LM258AWDT is suitable for conditioning low-frequency industrial sensor signals because its two channels can amplify or buffer a sensor output within a common 3 V to 30 V supply architecture. Its 20 nA input bias current limits the loading imposed on relatively high-impedance sensing elements, while the 1.1 MHz gain-bandwidth product provides more bandwidth than required for many slow process-control signals. A practical implementation uses one channel for amplification and the other for filtering or active feedback. Designers should confirm that the transducer’s common-mode voltage remains inside the input range and that the output stays within ±1.5 V to ±15 V limits for the selected supply. The 85 dB open-loop gain can support closed-loop gains selected according to the application’s noise and stability requirements.

🚗

Automotive Sensor Interface

The AEC-Q100-qualified LM258AWDT fits automotive sensing interfaces that require two low-power amplifier channels on a wide supply rail. The device accepts a 3 V to 30 V supply and offers 60 mA output current per channel, providing flexibility when an interface must drive an intermediate buffer or downstream protection stage. A common implementation buffers a differential sensor signal on one channel and provides gain or active filtering on the other. Because the amplifier does not provide rail-to-rail operation, the vehicle’s supply transients and the sensor common-mode range must be checked against the manufacturer limits. Qualification status alone does not establish suitability for every vehicle platform, so system-level transient, temperature, and diagnostic requirements remain important.

🔋

Battery-Powered Instrumentation

The LM258AWDT is appropriate for battery-powered instrumentation where a conventional low-power dual op amp is needed across varying supply conditions. Its approximately 0.1 µA quiescent-current figure per amplifier helps limit standing consumption, while the broad 3 V to 30 V supply range supports both compact low-voltage systems and higher industrial rails. The 20 nA input bias current is advantageous when measuring high-impedance sources, such as resistive sensors or leakage-sensitive dividers. Its 1.1 MHz gain-bandwidth product is appropriate for low-frequency measurement paths rather than wideband instrumentation. The circuit should use low-leakage board materials and guard techniques where source resistance is very high, while the power budget must include amplifier quiescent current, load current, and any external bias current.

⚡

Current-Loop Signal Receiver

The LM258AWDT can serve as the receiver amplifier for a 4-20 mA industrial current loop when the application operates within its input and output voltage limits. Two channels may be used to improve signal conditioning flexibility, such as combining a precision gain stage with an active filter or output driver. The 60 mA per-channel output-current rating provides useful drive capability, and the 1.1 MHz gain-bandwidth product is more than adequate for loop bandwidths measured in hertz or low kilohertz. Critical design work involves setting the input burden and common-mode voltage, controlling offset error, and ensuring that the receiver supply has enough headroom. Protection against reversed polarity, surge events, and accidental overload belongs in the surrounding analog network rather than being assumed from the amplifier ratings.

🖥️

Analog-to-Digital Converter Driver

The LM258AWDT can drive the input of an analog-to-digital converter when the converter requires a low-frequency buffered signal rather than a high-speed waveform. The two channels can isolate the sensing network from the converter’s switched-capacitor input or provide gain and filtering ahead of conversion. Its 1.1 MHz gain-bandwidth product and 0.6 V/µs slew rate provide useful margin for moderate-bandwidth settling requirements. The output-current capability of 60 mA per channel helps drive converter input capacitance and associated protection networks, although the actual dynamic settling must be evaluated with the ADC model. Designers should account for output swing, load capacitance, converter acquisition time, and the possibility of kickback from the ADC sampling network when choosing compensation and isolation values.

🎧

Audio and Control Amplification

The LM258AWDT can amplify low-level audio or control signals when low bandwidth and low standing power are more important than rail-to-rail operation. One channel may provide preamplification for a low-frequency source, while the other forms an active filter or output driver. The 1.1 MHz gain-bandwidth product supports signal paths well beyond ordinary audio-band requirements, and the 0.6 V/µs slew rate is adequate for many low-frequency waveforms. In an audio design, output headroom and distortion under the intended load should be checked rather than inferred from the bandwidth alone. Feedback resistors should be kept at values that limit noise and loading, while bypass capacitance near the supply pins should follow the manufacturer’s stability recommendations. For portable equipment, the approximately 0.1 µA quiescent current per amplifier also reduces unnecessary battery drain.

What are the key specifications of LM258AWDT that engineers should know?
The LM258AWDT is a dual general-purpose operational amplifier with a 3 V to 30 V supply range, 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and two channels in an 8-pin SOIC package. It also provides 60 mA output current per channel, 20 nA input bias current, and 85 dB open-loop gain. The manufacturer datasheet identifies it as a low-power bipolar operational amplifier suitable for general-purpose analog signal conditioning.
What is the operating voltage range of LM258AWDT?
The LM258AWDT operates from 3 V to 30 V. The listed input and output voltage capability is ±1.5 V to ±15 V, corresponding to the positive and negative signal limits associated with the family’s supply configurations. According to the STMicroelectronics datasheet, the device is intended for low-power dual-operation operation across a broad supply range; applications requiring operation exactly at the upper supply limit must still observe the complete electrical-characteristics table.
Where can I download the LM258AWDT datasheet PDF?
The LM258AWDT datasheet PDF can be accessed through the manufacturer documentation link on this page or through the listed technical-document sources. The document contains the recommended application circuit, electrical characteristics, pin configuration, typical performance curves, and ordering information. Confirm the LM258AWDT ordering suffix against the package and temperature markings in the PDF before releasing a PCB design.
Where can I find the LM258AWDT pinout?
The LM258AWDT pin configuration is documented in the manufacturer datasheet under the pin-description and package-drawing sections. Its component is an 8-pin SOIC containing two operational amplifiers. Use the datasheet pin table when assigning supply, output, input, and feedback connections because this page does not reproduce the complete numbered pin list. The exposed electrical characteristics and recommended layout should be followed exactly.
Is LM258AWDT suitable for automotive applications?
Yes, the LM258AWDT is identified as an AEC-Q100-qualified automotive dual operational amplifier. It combines a 3 V to 30 V supply range with 1.1 MHz gain-bandwidth product and 0.6 V/µs slew rate in an 8-pin SOIC package. Qualification supports automotive design requirements, but the complete operating-temperature range, grade markings, production status, and application-specific AEC-Q100 test coverage must still be checked in the manufacturer documentation.
Where can I buy LM258AWDT online?
The LM258AWDT can be requested through the Request a Quote form on this page for current availability, lot handling, and order handling. The request should include your required quantity, acceptable packaging, target delivery date, and inspection requirements. This page does not name competing sellers or provide a static commercial quote, because pricing and stock can change without notice.
What is the price of LM258AWDT?
The current commercial price for LM258AWDT is shown through the Request a Quote form on this page. Submit the required quantity, reel or cut-tape preference, and target shipment region for a current quotation. The form is the appropriate channel for checking quantity-dependent pricing, availability, and logistics without relying on a potentially outdated unit-price figure.
What is the lead time and stock status for LM258AWDT?
Current LM258AWDT stock, lead time, and minimum-order quantity should be requested through the Request a Quote form on this page. Include the quantity, approved vendor list requirements, target date, and packaging needs in the request. A product-page listing alone does not establish a guaranteed inventory position, so confirm production availability and delivery timing before committing the design schedule.
What can replace LM258AWDT in an existing circuit?
The closest board-level replacement must use the same 8-pin SOIC footprint and the standard dual-op-amp pin arrangement. LM258AWYPT is an especially close candidate because it shares the listed 1.1 MHz bandwidth, 0.6 V/µs slew rate, 20 nA input bias current, 3 V to 30 V supply range, and 60 mA output-current rating. Verify package markings, temperature grade, qualification status, and the exact pinout before substitution.
Is LM258AWDT the same as LM258AWYPT?
The LM258AWDT and LM258AWYPT are closely related 8-SOIC versions with matching listed electrical parameters: 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 20 nA input bias current, 3 V to 30 V supply range, and 60 mA output current per channel. Both are identified as AEC-Q100 qualified. The suffix differences should still be checked against ordering, temperature, reel, and marking requirements in the manufacturer datasheet.
LM258AWDT vs TSH22IDT - which is better for a low-voltage signal chain?
The LM258AWDT is the better default when the existing board requires the qualified 3 V to 30 V low-power dual-op-amp design and its conventional input and output ranges are acceptable. TSH22IDT is a candidate in an 8-pin SOIC package, but its precision characteristics may target a different operating approach. Compare supply range, common-mode limits, output swing, stability, noise, and the manufacturer pin table before selecting it over the LM258AWDT.
When should I choose LM258AWDT over TSH22IDT?
Choose the LM258AWDT when qualification, a 3 V to 30 V supply range, 1.1 MHz bandwidth, and compatibility with an existing LM258-style circuit are the primary requirements. Its 20 nA input bias current and 60 mA output capability per channel also suit general-purpose instrumentation. Select TSH22IDT instead only after confirming that its electrical characteristics improve the target application without requiring layout, biasing, or output-range changes.
What is the best TI equivalent for LM258AWDT?
The TI LM258 family is the closest cross-brand family identified for an LM258-style dual general-purpose amplifier. The relevant TI ordering option must be selected in an 8-pin SOIC package and checked against the standard dual-op-amp pinout. Because the automotive qualification, temperature grade, and ordering suffix can differ from LM258AWDT, treat the family relationship as a starting point rather than a qualification or production-lifecycle guarantee.
Can LM258AWDT be used as a sensor amplifier?
Yes, the LM258AWDT can amplify low-frequency sensor signals when the sensor’s common-mode voltage and output range remain within the amplifier’s specified limits. Its 20 nA input bias current is useful with high-impedance sources, while the dual configuration can provide differential or instrumentation functions. For bridge sensors, verify excitation voltage, input offset behavior, output swing, and noise against the manufacturer’s application guidance.
What design limits matter when using LM258AWDT in a power supply?
The LM258AWDT is not a switching regulator and should not be treated as the primary power-conversion stage. In a linear-feedback application, the amplifier’s dissipation is approximately Estimated: P = (VIN − VOUT) × ILESS, using the actual input-output differential and load current. Keep that dissipation below the package and ambient-temperature limits, maintain input/output headroom, and confirm stability with the selected feedback network and load capacitance.

Impormasyon ng Talumpati sa Engineering for LM258AWDT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the LM258AWDT for dual-channel, low-frequency signal conditioning where the design can use a 3 V to 30 V supply, 20 nA input bias current, and up to 60 mA output current per channel. It is particularly appropriate when an AEC-Q100-qualified automotive part and the conventional LM258-style 8-SOIC footprint are required. LM258AWYPT is the closest listed substitute because its disclosed core ratings match exactly, but order-code, temperature, marking, and lifecycle requirements still need confirmation. TSH22IDT and TSB7192IDT are only 70%-proximity candidates because the available cross-reference information does not quantify all electrical differences or guarantee the detailed pin arrangement. The TI LM258AD option is useful for cross-brand sourcing, but its qualification and ordering status must be checked. For any alternative, verify the complete pin table, common-mode range, output swing, stability, thermal limits, and AEC-Q100 status before approving a substitution.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto LM258AWYPT LM258ADT TSH22IDT TSB7192IDT LM258AD
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments
Amplifier Configuration Dual general-purpose operational amplifier Dual general-purpose operational amplifier Dual LM258-family operational amplifier Dual operational amplifier Dual operational amplifier Dual LM258-family operational amplifier

Pangunahing mga Pagkakaiba

  • Closest listed same-family candidate matches the core electrical ratings (kumpara saLM258AWYPT)
  • Automotive qualification is identified for the replacement candidate (kumpara saLM258AWYPT)
  • Provides two channels in a conventional 8-SOIC footprint (kumpara saTSH22IDT)

Talaan ng Disenyo

Estimate dissipation in linear-feedback service with Estimated: P = (VIN − VOUT) × ILESS, where ILESS includes load current plus input-bias and feedback contributions. For example, a 12 V input, 5 V output, and 1 mA load gives an estimated 7 mW dissipation. The much larger risk is incorrect output-range planning: confirm that the selected feedback network keeps the output between the datasheet’s common-mode and output limits at every supply condition.

Place the input, output, feedback, and bypass components close to their associated SOIC pins. Route the feedback loop as a compact, low-impedance path and keep the output node physically separated from the non-inverting input to reduce parasitic coupling. If the amplifier drives an ADC or cable input, reserve protection and isolation components in the output path. Follow the manufacturer’s recommended decoupling arrangement and thermal-copper pattern for the exact package.

Do not assume rail-to-rail input or output behavior merely because the supply can reach 30 V. The listed input and output range is ±1.5 V to ±15 V, so common-mode voltage and output swing can become the limiting specifications in single-supply designs. Also verify that the circuit does not attempt to operate below the minimum 3 V supply and that source resistance remains compatible with the 20 nA input-bias-current specification.

Confirm loop stability with the actual source impedance, load capacitance, feedback resistors, and supply decoupling. The 1.1 MHz gain-bandwidth product does not guarantee stability at every closed-loop gain or capacitive load. Add isolation resistance between the op-amp output and highly capacitive loads, and compare the resulting bandwidth and settling behavior with the signal source and downstream acquisition requirements.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The LM258AWDT is identified as AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer or distributor information.

Kaugnay na Hanapin

LM258AWDT datasheet LM258AWDT pinout LM258AWDT datasheet pdf LM258AWDT specifications LM258AWDT 8-SOIC STMicroelectronics LM258AWDT LM258AWDT automotive op amp LM258AWDT drop-in replacement LM258AWDT equivalent LM258AWDT vs LM258AWYPT LM258AWDT price LM258AWDT stock LM258AWDT application circuit LM258AWDT cross reference

Mga kaugnay na Mga Komponente at mga Tuntunin

STMicroelectronics LM258AWDT LM258AWYPT LM258ADT TSH22IDT TSB7192IDT LM258AD Texas Instruments dual operational amplifier general-purpose amplifier amplifier IC signal-conditioning IC semiconductor low-power operation 3 V to 30 V supply 1.1 MHz gain-bandwidth product 0.6 V/µs slew rate 20 nA input bias current 60 mA output current 8-pin SOIC SOIC package family surface-mount package AEC-Q100 automotive electronics
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ