LM258AWDT - Dual 30V Low-Power Op Amp | STMicroelectronics
MPN: LM258AWDT ✓ 啟用中LM258AWDT 概覽
A general-purpose operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify a voltage difference. In the broader electronics hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories, where it supports sensor interfaces, buffer stages, error amplifiers, analog-to-digital converter drivers, and general feedback-control circuits. The LM258 family combines broad supply-voltage tolerance with low quiescent-current operation, making it useful where the signal level and supply voltage vary across industrial or automotive equipment.
The principal features of the LM258AWDT include two independent channels, a 3 V to 30 V operating range, 85 dB open-loop gain-bandwidth behavior, low 20 nA input bias current, and approximately 0.1 µA input offset current. Its 1.1 MHz gain-bandwidth product supports moderate-frequency signal amplification, while the 0.6 V/µs slew rate supports reasonably clean output transitions. A 60 mA per-channel output-current capability is useful for driving moderate loads and providing isolation between high-impedance sources and downstream circuitry.
The automotive “A” version is identified as AEC-Q100 qualified in the available component information. This qualification is meaningful in applications where operating temperature, shock, vibration, and extended-life reliability require controlled automotive qualification. Because it is a bipolar, low-power dual op amp, the LM258AWDT emphasizes supply flexibility and input-current behavior rather than rail-to-rail input or output operation. Its usable common-mode and output ranges therefore need to remain inside the limits specified by the manufacturer datasheet.
Typical applications include industrial sensor conditioning, battery-powered instrumentation, current-loop receivers, analog signal buffers, bridge-amplifier interfaces, and low-frequency control loops. Automotive electronics can use the qualified version where its operating and environmental ratings match the system requirements. Two channels can be used independently or together for differential, summing, instrumentation, or active-filter configurations, reducing the number of separate amplifier packages required on a board.
The main design consideration is rail-to-rail behavior. A circuit requiring input or output swing close to either supply rail may not be served by the LM258AWDT’s conventional common-mode range. Designers should also check output-current limits, load capacitance, supply ripple, feedback stability, and the minimum operating voltage for the selected gain configuration before finalizing the circuit.
This page combines the LM258AWDT’s principal electrical ratings, automotive qualification, package details, practical applications, same-footprint alternatives, and design guidance to support component selection, PCB planning, sourcing, and schematic review.
直接替換替代品,適用於 LM258AWDT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM258AWDT (相同外形與佔位) — 差異在於 Gain-Bandwidth Product, Package.
LM258AWYPT
✅ 直接替換📋 參考替代品(不在目錄中)
LM258ADT
✅ 直接替換📋 參考替代品(不在目錄中)
TSH22IDT
✅ 直接替換📋 參考替代品(不在目錄中)
TSB7192IDT
✅ 直接替換📋 參考替代品(不在目錄中)
LM258AWDT 最大額定值與電氣特性
| Amplifier Type | General-purpose dual operational amplifier |
| Number of Channels | 2 circuits |
| Supply Voltage Range | 3 V to 30 V |
| 輸入電壓範圍 | ±1.5 V to ±15 V |
| 輸出電壓範圍 | ±1.5 V to ±15 V |
| Output Current per Channel | 60 mA |
| Input Bias Current | 20 nA |
| Input Offset Current | 0.1 µA |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 0.6 V/µs |
| Open-Loop Gain | 85 dB |
| 靜態電流 | 0.1 µA per amplifier |
| 封裝 | 8-pin SOIC, 0.154 inch body width |
| Package Dimensions | 0.154 inch width × 3.90 mm length |
| 安裝類型 | Surface mount |
| Packaging | Tape and reel |
| Automotive Qualification | AEC-Q100 qualified |
LM258AWDT 0.154 inch width × 3.90 mm length 腳位配置指南
LM258AWDT(0.154 inch width × 3.90 mm length 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM258AWDT.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM258AWDT 適用於 6 應用s: Industrial Sensor Signal Conditioning, Automotive Sensor Interface, Battery-Powered Instrumentation, Current-Loop Signal Receiver, Analog-to-Digital Converter Driver, Audio and Control Amplification.
Industrial Sensor Signal Conditioning
The LM258AWDT is suitable for conditioning low-frequency industrial sensor signals because its two channels can amplify or buffer a sensor output within a common 3 V to 30 V supply architecture. Its 20 nA input bias current limits the loading imposed on relatively high-impedance sensing elements, while the 1.1 MHz gain-bandwidth product provides more bandwidth than required for many slow process-control signals. A practical implementation uses one channel for amplification and the other for filtering or active feedback. Designers should confirm that the transducer’s common-mode voltage remains inside the input range and that the output stays within ±1.5 V to ±15 V limits for the selected supply. The 85 dB open-loop gain can support closed-loop gains selected according to the application’s noise and stability requirements.
推薦
Automotive Sensor Interface
The AEC-Q100-qualified LM258AWDT fits automotive sensing interfaces that require two low-power amplifier channels on a wide supply rail. The device accepts a 3 V to 30 V supply and offers 60 mA output current per channel, providing flexibility when an interface must drive an intermediate buffer or downstream protection stage. A common implementation buffers a differential sensor signal on one channel and provides gain or active filtering on the other. Because the amplifier does not provide rail-to-rail operation, the vehicle’s supply transients and the sensor common-mode range must be checked against the manufacturer limits. Qualification status alone does not establish suitability for every vehicle platform, so system-level transient, temperature, and diagnostic requirements remain important.
推薦
Battery-Powered Instrumentation
The LM258AWDT is appropriate for battery-powered instrumentation where a conventional low-power dual op amp is needed across varying supply conditions. Its approximately 0.1 µA quiescent-current figure per amplifier helps limit standing consumption, while the broad 3 V to 30 V supply range supports both compact low-voltage systems and higher industrial rails. The 20 nA input bias current is advantageous when measuring high-impedance sources, such as resistive sensors or leakage-sensitive dividers. Its 1.1 MHz gain-bandwidth product is appropriate for low-frequency measurement paths rather than wideband instrumentation. The circuit should use low-leakage board materials and guard techniques where source resistance is very high, while the power budget must include amplifier quiescent current, load current, and any external bias current.
推薦
Current-Loop Signal Receiver
The LM258AWDT can serve as the receiver amplifier for a 4-20 mA industrial current loop when the application operates within its input and output voltage limits. Two channels may be used to improve signal conditioning flexibility, such as combining a precision gain stage with an active filter or output driver. The 60 mA per-channel output-current rating provides useful drive capability, and the 1.1 MHz gain-bandwidth product is more than adequate for loop bandwidths measured in hertz or low kilohertz. Critical design work involves setting the input burden and common-mode voltage, controlling offset error, and ensuring that the receiver supply has enough headroom. Protection against reversed polarity, surge events, and accidental overload belongs in the surrounding analog network rather than being assumed from the amplifier ratings.
推薦
Analog-to-Digital Converter Driver
The LM258AWDT can drive the input of an analog-to-digital converter when the converter requires a low-frequency buffered signal rather than a high-speed waveform. The two channels can isolate the sensing network from the converter’s switched-capacitor input or provide gain and filtering ahead of conversion. Its 1.1 MHz gain-bandwidth product and 0.6 V/µs slew rate provide useful margin for moderate-bandwidth settling requirements. The output-current capability of 60 mA per channel helps drive converter input capacitance and associated protection networks, although the actual dynamic settling must be evaluated with the ADC model. Designers should account for output swing, load capacitance, converter acquisition time, and the possibility of kickback from the ADC sampling network when choosing compensation and isolation values.
推薦
Audio and Control Amplification
The LM258AWDT can amplify low-level audio or control signals when low bandwidth and low standing power are more important than rail-to-rail operation. One channel may provide preamplification for a low-frequency source, while the other forms an active filter or output driver. The 1.1 MHz gain-bandwidth product supports signal paths well beyond ordinary audio-band requirements, and the 0.6 V/µs slew rate is adequate for many low-frequency waveforms. In an audio design, output headroom and distortion under the intended load should be checked rather than inferred from the bandwidth alone. Feedback resistors should be kept at values that limit noise and loading, while bypass capacitance near the supply pins should follow the manufacturer’s stability recommendations. For portable equipment, the approximately 0.1 µA quiescent current per amplifier also reduces unnecessary battery drain.
推薦
推薦產品摘要
工程參考資料,適用於 LM258AWDT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM258AWYPT | LM258ADT | TSH22IDT | TSB7192IDT | LM258AD |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Amplifier Configuration | Dual general-purpose operational amplifier | Dual general-purpose operational amplifier | Dual LM258-family operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual LM258-family operational amplifier |
主要差異化特點
- Closest listed same-family candidate matches the core electrical ratings (對比LM258AWYPT)
- Automotive qualification is identified for the replacement candidate (對比LM258AWYPT)
- Provides two channels in a conventional 8-SOIC footprint (對比TSH22IDT)
設計說明
Estimate dissipation in linear-feedback service with Estimated: P = (VIN − VOUT) × ILESS, where ILESS includes load current plus input-bias and feedback contributions. For example, a 12 V input, 5 V output, and 1 mA load gives an estimated 7 mW dissipation. The much larger risk is incorrect output-range planning: confirm that the selected feedback network keeps the output between the datasheet’s common-mode and output limits at every supply condition.
Place the input, output, feedback, and bypass components close to their associated SOIC pins. Route the feedback loop as a compact, low-impedance path and keep the output node physically separated from the non-inverting input to reduce parasitic coupling. If the amplifier drives an ADC or cable input, reserve protection and isolation components in the output path. Follow the manufacturer’s recommended decoupling arrangement and thermal-copper pattern for the exact package.
Do not assume rail-to-rail input or output behavior merely because the supply can reach 30 V. The listed input and output range is ±1.5 V to ±15 V, so common-mode voltage and output swing can become the limiting specifications in single-supply designs. Also verify that the circuit does not attempt to operate below the minimum 3 V supply and that source resistance remains compatible with the 20 nA input-bias-current specification.
Confirm loop stability with the actual source impedance, load capacitance, feedback resistors, and supply decoupling. The 1.1 MHz gain-bandwidth product does not guarantee stability at every closed-loop gain or capacitive load. Add isolation resistance between the op-amp output and highly capacitive loads, and compare the resulting bandwidth and settling behavior with the signal source and downstream acquisition requirements.
合規資訊
The LM258AWDT is identified as AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer or distributor information.