LM2900NE4 - Quad Norton Op Amp, 2.5 MHz | Texas Instruments
MPN: LM2900NE4 ✓ NakahandaLM2900NE4 Ulas
The LM2900NE4 uses the Norton current-feedback operational-amplifier architecture. Unlike a conventional voltage-feedback amplifier, the Norton topology is based on low-input-resistance current feedback and is well suited to applications where the source impedance and feedback network are compatible with that operating principle. Internal frequency compensation makes the amplifier convenient to use without external compensation components in closed-loop gain configurations specified by the manufacturer.
Key specifications include four amplifier circuits, a 2.5 MHz gain-bandwidth product, a 20 V/µs slew rate, and a 14-pin PDIP package. The device also provides wide supply-voltage operation, large output-voltage swing, output short-circuit protection, and low input-bias-current characteristics according to the LM2900 family information. These features make the LM2900NE4 suitable for industrial control, sensor interfaces, audio and communication signal paths, and test equipment.
The quad package can reduce board area when four similar analog functions are required. Each amplifier is independent, allowing the same device to implement four separate gain, buffering, comparison, or filtering functions. The PDIP format is also convenient for through-hole assembly, prototyping, repair, and applications where a large thermal pad is not required.
When designing around the LM2900NE4, verify the source impedance and feedback values against the manufacturer’s recommended operating conditions. Because the Norton architecture has different input and feedback considerations from a voltage-feedback op amp, do not substitute a conventional amplifier without checking stability, slew behavior, output swing, and bias-current requirements. Maintain adequate supply decoupling and observe the specified common-mode and output-voltage limits.
This product page combines the manufacturer family information, distributor package and availability references, technical comparisons, and practical design guidance to support component selection and replacement planning for the LM2900NE4.
Mga alternatibo na pwedeng ilagay na LM2900NE4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM2900NE4 (parehas na form factor at footprint) — pagkakaiba sa Frequency Compensation, Package, Short-Circuit Protection.
LM2900N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM3900NE4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
LM2900NE4 Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Amplifier Circuits | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Architecture | Quad high-gain frequency-compensated Norton current-feedback amplifier |
| Gain-Bandwidth Product | 2.5 MHz |
| Slew Rate | 20 V/µs |
| Volte ng Pagbibigay | Up to 15 V |
| Supply Configuration | Single or split supply |
| Packhaging | 14-PDIP, 0.300 inch pitch |
| Package Type | Through-hole PDIP |
| Frequency Compensation | Internal frequency compensation |
| Output Voltage Swing | Large output voltage swing |
| Short-Circuit Protection | Output short-circuit protection |
Gabay sa Pin Configuration ng LM2900NE4 through-hole pdip
Pin configuration para sa LM2900NE4 (through-hole pdip package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2900NE4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2900NE4 ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Audio and Communication Signal Paths, Power Supply Monitoring and Control Loops, Test and Measurement Front Ends, Active Filtering and Waveform Conditioning, Legacy Through-Hole Control Boards.
Industrial Sensor Signal Conditioning
The LM2900NE4 is suitable for conditioning signals from sensors whose source impedance is compatible with the LM2900 Norton architecture. Its four independent amplifier sections can support multiple conditioning channels within one 14-pin PDIP device. A 2.5 MHz gain-bandwidth product permits useful bandwidth for general-purpose industrial measurement, while the 20 V/µs slew rate supports faster signal transitions. The design must follow the manufacturer’s recommended feedback values and source-impedance limits; otherwise stability and usable bandwidth can differ from conventional voltage-feedback amplifier behavior.
Inirekomenda
Audio and Communication Signal Paths
The LM2900NE4 can process general audio-band and communication signals where a wideband quad amplifier is useful. Its 20 V/µs slew rate provides substantially faster large-signal movement than a basic low-frequency amplifier, while the 2.5 MHz gain-bandwidth product covers more than the audible band. Four amplifier sections allow mixing of buffering, gain, and filtering functions in one package. Check source impedance, feedback values, output swing, supply level, and stability against the LM2900 datasheet before using it in a new Norton current-feedback design.
Inirekomenda
Power Supply Monitoring and Control Loops
The LM2900NE4 can implement voltage comparison, error amplification, and auxiliary control functions in an industrial power-control board. Four independent amplifier sections allow several low-frequency feedback loops to share one package, and the 14-lead PDIP format is convenient for through-hole industrial control assemblies. The 2.5 MHz gain-bandwidth product is suitable for many slow regulation loops, while the 20 V/µs slew rate provides useful response margin. Verify the common-mode range and output swing at the actual supply voltage because the amplifier cannot drive outputs beyond its specified operating limits.
Inirekomenda
Test and Measurement Front Ends
The LM2900NE4 is appropriate for general-purpose instrumentation front ends when the Norton feedback network is selected correctly. Its four sections can be used for input conditioning, active filtering, gain stages, and output buffering, while the 2.5 MHz gain-bandwidth product supports bandwidth beyond traditional precision low-frequency amplifier limits. The 20 V/µs slew rate helps preserve large-signal waveform shape. For precision measurement, compare input bias current, offset, common-mode range, and noise against the application requirements rather than relying on bandwidth alone.
Inirekomenda
Active Filtering and Waveform Conditioning
The LM2900NE4 can form active filters and waveform-conditioning stages where four related amplifier sections are advantageous. Its 2.5 MHz gain-bandwidth product provides the basis for moderate-bandwidth filter sections, and its 20 V/µs slew rate improves large-signal response compared with slower general-purpose amplifiers. Because this is a Norton current-feedback device, each feedback component and source impedance must be calculated for the intended closed-loop gain. Check output-current capability and output swing before driving heavy loads or producing large amplitude waveforms.
Inirekomenda
Legacy Through-Hole Control Boards
The LM2900NE4 is especially practical for legacy control boards that use a 14-PDIP footprint and require four general-purpose amplifier functions. Its through-hole package supports conventional PCB insertion, socketed prototyping, and repair without a fine-pitch assembly process. The tube packaging identified for this ordering code also aligns with conventional component-handling workflows. For an existing board, confirm every pin function against the manufacturer pin-description table and verify operating temperature, supply voltage, bias current, and load-driving requirements before substitution or reuse.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2900NE4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM2900N | LM3900NE4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-PDIP (0.300, 7.62mm) | 14-PDIP (0.300, 7.62mm) | 14-PDIP (0.300, 7.62mm) |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Architecture | Norton current-feedback | Norton current-feedback | Norton current-feedback |
Pangunahing mga Pagkakaiba
- Four independent Norton amplifier sections in one package (kumpara saLM2900N)
- Defined 2.5 MHz gain-bandwidth product and 20 V/µs slew rate (kumpara saLM3900NE4)
- Single-supply and split-supply operating capability (kumpara saLM2900N)
Talaan ng Disenyo
Do not treat the LM2900NE4 as a conventional voltage-feedback operational amplifier when selecting feedback resistors. The Norton architecture requires the source impedance and feedback network to follow the LM2900 family recommendations. Review the manufacturer application information for the intended closed-loop gain, then check stability and usable bandwidth on the actual PCB. This prevents oscillation, unexpected gain, or poor transient response.
Place bypass capacitors close to the power-supply pins and keep the input and feedback tracks short to reduce parasitic inductance and capacitance. A PDIP layout should provide adequate clearance between adjacent traces, especially around high-impedance input nodes. Because high-impedance nodes are particularly sensitive in a Norton topology, avoid long parallel runs and keep nearby switching or high-current return paths physically separated.
Check the output-current demand and voltage drop across the amplifier when driving a load. The stated 20 V/µs slew rate is a large-signal response specification, not an output-current limit, and the device has a listed maximum supply voltage of 15 V. Keep the output within its specified swing range and include adequate supply bypassing. For calculations not taken directly from the manufacturer datasheet, label any derived dissipation and junction-temperature result as an estimate using the actual supply, output, load, and thermal resistance.
For instrumentation and waveform conditioning, verify gain-bandwidth behavior at the selected closed-loop gain rather than assuming the full 2.5 MHz is available. Also compare the 20 V/µs slew rate with the required output amplitude and frequency. A square wave at higher frequency can be limited by slew rate even when the small-signal bandwidth appears adequate. Confirm common-mode range, output swing, and load capacitance using the manufacturer data.
Impormasyon ng Pagsunod sa Kautusan
No explicit compliance declarations were identified in the cited product and distributor records. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with the manufacturer for the exact ordering code.