Texas Instruments

LM2902MT - Quad 26V 1.2MHz Op-Amp 14-TSSOP | Texas Instruments

MPN: LM2902MT ✓ Nakahanda
2 mV (typical) Vdss 14-TSSOP Package
MOQ: 1 |

LM2902MT Ulas

The Texas Instruments LM2902MT is a quad general-purpose operational amplifier with four independent, internally frequency-compensated high-gain amplifier circuits in a 14-pin TSSOP package. It operates from supply voltages up to 26 V, delivers a 1.2 MHz gain-bandwidth product, and provides a typical input offset voltage of 2 mV, with output voltage swing of +/-13 V on a +/-15 V class supply (26 V total range).

A quad operational amplifier (op-amp) is an analog IC that integrates four identical voltage amplifiers on one silicon die sharing a common bias and supply network. Op-amps form the foundation of the analog signal-chain hierarchy: op-amp -> amplifier IC -> analog front end -> signal conditioning, making the LM2902 family one of the most widely deployed amplifier platforms in industrial electronics.

Key features include single-supply operation over a wide voltage range (3 V to 26 V per the LM2902 product family, with split-supply operation possible when the supply difference is 3 V to 26 V), internal frequency compensation that eliminates external compensation components, and a common-mode input range that extends to ground (negative rail), which is essential for single-supply sensing circuits.

Architecturally, the LM2902 uses class-AB output stages with internal compensation, allowing stable unity-gain operation without external capacitors. The four amplifiers share supply rails while remaining electrically independent, so each channel can be configured as inverting, non-inverting, differential, or transimpedance amplifier independently.

Typical applications include industrial signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and automotive sensor interfaces where the extended temperature capability of the LM2902 grade is required.

For design, ensure the output stays within the output-voltage swing limits relative to each rail; driving loads too close to the rails can reduce open-loop gain. Decouple the supply pin with 100 nF close to the device.

This page adds value beyond the datasheet by compiling drop-in alternative MPNs, package/pinout verification, FAQ answers based on real search queries, and practical design notes not found on the manufacturer product page.

Mga alternatibo na pwedeng ilagay na LM2902MT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok LM2902MT (parehas na form factor at footprint) — pagkakaiba sa Package, Operating Temperature Range, Input Offset Voltage, Product Type, Amplifier Type.

onsemi
Package: 14-pin SOP
Operating Temperature Range: -40 °C to +85 °C
Product Type: Quad operational amplifier
Ikabit sa LM2902MT →
Texas Instruments
Operating Temperature Range: -40°C to 85°C
Input Offset Voltage: 2 mV
Amplifier Type: General-purpose operational amplifier
Texas Instruments
Package: 14-pin TSSOP (PW)
Operating Temperature Range: -40°C to +125°C
Input Offset Voltage: 2 mV
Ikabit sa LM2902MT →
Texas Instruments
Package: 14-pin SOIC
Product Type: Quad operational amplifier
Ikabit sa LM2902MT →

LM2902MT/NOPB

✅ Drop-In
Texas Instruments
📦 14-TSSOP
General-purpose operational amplifier · 4 circuits · 26 V · 1.2 MHz · 2 mV · Single or split supply · -40°C to 85°C · 14-TSSOP

Magkontak para sa presyo

Tingnan ang Datasheet →

LM2902M

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
onsemi
📦 14-TSSOP
Quad operational amplifier · 4 circuits · 26 V · 1.2 MHz · 2 mV · Standard general-purpose amplifier · Internal frequency compensation · 4 independent amplifiers

Magkontak para sa presyo

Tingnan ang Datasheet →

LM2902QPWRQ1

✅ Drop-In
Texas Instruments
📦 14-TSSOP (PW)
4 circuits · Quad general-purpose operational amplifier · 26 V · 1.2 MHz · 2 mV · Single supply or split supply · High-gain, internally frequency-compensated

Magkontak para sa presyo

Tingnan ang Datasheet →

LM2902MT/TR

✅ Drop-In
📦 14-TSSOP
second-source HGSEMI LM2902 quad op-amp, tape and reel; same standard quad pinout, verify electrical limits against HGSEMI datasheet

📋 Alternatibo na Reference (hindi sa katalogo)

LM324M

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Texas Instruments
📦 14-SOIC
Quad operational amplifier · 4 circuits · Four independent amplifiers · Internally frequency compensated · Single-supply operation across a wide voltage range · Standard general-purpose amplifier · Instrumentation, signal amplification, and buffering · 14-pin SOIC

Magkontak para sa presyo

Tingnan ang Datasheet →

LM2902MT Mga Pinakamataas na Rating at Electrical Characteristics

Number of Circuits 4
Amplifier Type General Purpose Operational Amplifier
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV (typical)
Supply Voltage Range up to 26 V
Output Voltage Swing +/-13 V / 26 V
Operating Mode Single supply or split supply
Internal Compensation Yes (internally frequency compensated)
Packhaging 14-TSSOP
Uri ng Pagpapasok Surface Mount
Packaging Tube
Tindminan RoHS Compliant

Pin Configuration ng LM2902MT

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pin 1 OUT1 — Output of amplifier 1
Pin 2 IN1- — Inverting input of amplifier 1
Pin 3 IN1+ — Non-inverting input of amplifier 1
Pin 4 VCC — Positive supply voltage
Pin 5 IN2+ — Non-inverting input of amplifier 2
Pin 6 IN2- — Inverting input of amplifier 2
Pin 7 OUT2 — Output of amplifier 2
Pin 8 OUT3 — Output of amplifier 3
Pin 9 IN3- — Inverting input of amplifier 3
Pin 10 IN3+ — Non-inverting input of amplifier 3
Pin 11 VEE/GND — Negative supply or ground (single-supply operation)
Pin 12 IN4+ — Non-inverting input of amplifier 4
Pin 13 IN4- — Inverting input of amplifier 4
Pin 14 OUT4 — Output of amplifier 4

Tipikal na mga Gamit

LM2902MT ay nararapat para sa 6 aplikasyons: Industrial Signal Conditioning, Transducer Amplifier Front Ends, Active Filter Networks, DC Gain Blocks and Level Shifting, Comparator and Threshold Detection Circuits, Automotive and Wide-Temperature Sensor Interfaces.

🏭

Industrial Signal Conditioning

The LM2902MT is a natural fit for industrial signal conditioning front ends because it combines four amplifiers in one 14-TSSOP package and its input common-mode range extends to ground, allowing ground-referenced sensor signals to be amplified directly from a single supply. With operation up to 26 V total supply, it can sit directly on industrial 24 V rails without an intermediate regulator. Typical circuits include 4-20 mA current-loop receivers, potentiometer scaling stages, and differential amplifier blocks built from two of the four channels. The 1.2 MHz gain-bandwidth product comfortably covers process-variable bandwidths well below 10 kHz at closed-loop gains up to 100, where the 2 mV typical offset contributes only a few hundred millivolts of output error. Decouple the supply pin with 100 nF ceramics placed close to the device to reject switching noise from nearby power electronics.

🔧

Transducer Amplifier Front Ends

Sensor transducers such as pressure bridges, thermistor dividers, and photodiode loads produce small ground-referenced signals, and the LM2902MT's common-mode input range that includes the negative rail makes single-supply amplification straightforward without a negative supply generator. One channel can buffer the sensor while a second channel provides gain and a third generates a mid-scale reference, all from the same die for matched drift behavior. With a 1.2 MHz bandwidth, resistive photodiode transimpedance circuits up to roughly 100 kHz closed-loop bandwidth are practical. The 2 mV typical input offset should be budgeted at the chosen closed-loop gain; for a gain of 100, expect about 200 mV of referred output offset. A 100 nF decoupling capacitor at pin 4 and solid grounding at pin 11 preserve the microvolt-level stability the front end needs.

🔧

Active Filter Networks

Multiple Sallen-Key or multiple-feedback filter stages can be built on a single LM2902MT because the package integrates four independently configurable amplifiers sharing one supply. Two cascaded second-order sections produce a fourth-order low-pass or band-pass response for anti-aliasing and noise-limiting duties ahead of ADCs. The 1.2 MHz gain-bandwidth product means cutoff frequencies up to roughly 20-50 kHz can be realized with accurate Q and gain, since the amplifier open-loop gain remains high relative to the filter pole frequencies. Internal compensation guarantees unity-gain stability required by Sallen-Key topologies. The 14-TSSOP surface-mount package keeps the filter footprint compact on mixed-signal boards, and the 26 V supply rating allows filtering on higher-voltage industrial rails directly.

⚡

DC Gain Blocks and Level Shifting

The LM2902MT excels as a DC gain block: its input common-mode range to ground and output swing near the rails suit unipolar level translation between 0-5 V sensor domains and higher-voltage 24 V control domains. A standard two-channel configuration implements a difference amplifier that subtracts and scales offset voltages, while the remaining channels provide input buffering to keep source impedance from corrupting the ratio-match of the gain-setting resistors. The 2 mV typical offset and modest drift should be included in the accuracy budget of DC applications; where required, a trimming resistor on the reference node recovers most of it. With a total supply range up to 26 V, the gain block can run directly from industrial supplies. Use 1% or better resistors for the gain network to preserve common-mode rejection.

⚙️

Comparator and Threshold Detection Circuits

One or more LM2902MT channels can operate open-loop as comparators with hysteresis, flagging threshold crossings from sensors or power rails. The amplifier's input range to ground permits sensing ground-referenced thresholds on a single supply, and output swing near the rails produces clean logic-compatible flags. Add positive feedback (typically 1-100 kOhm ratios) to create hysteresis and prevent chatter from slow-moving analog signals; this also improves noise immunity near the trip point. Note that as an op-amp rather than a dedicated comparator, response time is on the order of microseconds rather than nanoseconds, so the LM2902MT suits supervisory and slow threshold detection rather than fast protection. The 26 V supply ceiling allows threshold detection directly on industrial 24 V buses.

🚗

Automotive and Wide-Temperature Sensor Interfaces

The LM2902 grade was developed for automotive and industrial environments where ambient temperatures exceed commercial limits, and it remains a common choice for battery-voltage monitoring, alternator output scaling, throttle position buffering, and coolant-temperature signal conditioning. The 26 V total supply rating tolerates load-dump-adjacent conditions when paired with upstream protection, and four channels per package reduce component count on cost-sensitive body modules. The 1.2 MHz bandwidth easily covers the low-frequency content of automotive sensor signals, and the ground-including common-mode range simplifies chassis-referenced measurement. For programs requiring documented automotive qualification, verify the AEC-Q100 status of the specific ordering code, or specify the Q1-grade LM2902 variant in the same TSSOP-14 footprint for qualification paperwork.

What is the LM2902MT operational amplifier?
The LM2902MT is a Texas Instruments quad general-purpose operational amplifier containing four independent, internally frequency-compensated amplifier circuits in a 14-pin TSSOP surface-mount package. According to the TI LM2902 product page, it supports operation up to 26 V total supply, provides a 1.2 MHz gain-bandwidth product and 2 mV typical input offset voltage, and can run from a single supply or split supplies.
What is the supply voltage range of the LM2902MT?
The LM2902MT operates with a total supply voltage up to 26 V according to the TI LM2902 product page. It can operate from a single supply over a wide voltage range, or from split supplies when the difference between the two supplies is 3 V to 26 V, with each supply at least 1.5 V above the specified minimum. This flexibility makes it suitable for both 5 V logic-domain and higher-voltage industrial rails.
What is the difference between LM2902MT and LM2902MT/NOPB?
The LM2902MT and LM2902MT/NOPB are the same silicon die in the same 14-TSSOP package from Texas Instruments. The /NOPB suffix simply designates the lead-free, RoHS-compliant (No Pb) ordering option with tube packing. Electrically both parts offer four 26 V, 1.2 MHz op-amp channels, so either ordering code can be used in the same PCB footprint and schematic without any design change.
What is the gain-bandwidth product of the LM2902MT?
The LM2902MT has a gain-bandwidth product of 1.2 MHz, as listed on the Texas Instruments LM2902 product page. This means at a closed-loop gain of 10, the bandwidth is approximately 120 kHz, and at unity gain the amplifier stays stable thanks to internal frequency compensation. For audio, sensor, and low-speed control loops this bandwidth is fully adequate; for higher-speed signal chains consider a faster amplifier family.
What is the input offset voltage of the LM2902MT?
The LM2902MT has a typical input offset voltage of 2 mV according to the TI LM2902 product specification. At a closed-loop gain of 100, this offset appears as roughly 200 mV of output error before calibration. If your application requires sub-millivolt accuracy without trimming, consider a precision or zero-drift amplifier family instead; for general-purpose gain blocks the 2 mV typical offset is acceptable.
Can LM2902MT replace LM324?
Yes. The LM2902 and LM324 are essentially the same quad op-amp architecture, with the primary differences being maximum supply voltage rating and operating temperature grade; both support a recommended supply range of 3 V to 36 V for the B-version devices and share gain-bandwidth, slew rate, offset, and bias current limits. The LM2902MT in 14-TSSOP is pin-to-pin compatible with LM324-family parts in TSSOP-14, so it drops into existing designs without PCB modification.
Is the LM2902MT suitable for single-supply operation?
Yes, the LM2902MT is specifically designed for single-supply operation over a wide voltage range, which is one of its defining features per the TI LM2902 family description. The common-mode input range includes the negative rail (ground), and outputs can swing close to the lower rail. This makes it ideal for ground-referenced sensor amplification in 5 V or 24 V single-supply industrial systems without requiring a negative supply.
What is the best drop-in replacement for LM2902MT?
The best drop-in replacements are the Texas Instruments LM2902MT/NOPB (identical die and package, lead-free ordering code) and other LM2902-family parts in the same 14-TSSOP footprint, such as the LM2902M. On the cross-brand side, the HGSEMI LM2902MT/TR is offered in the same TSSOP-14 footprint as a second-source option. All preserve the standard quad op-amp pinout, so replacement requires no schematic or layout changes.
Can LM2902MT be used in automotive applications?
The LM2902 grade is the extended-temperature member of the LM124/LM324/LM2902 family and has traditionally been targeted at automotive and industrial environments where wider temperature operation is required. For applications with formal automotive qualification requirements, verify the exact AEC-Q100 qualification status of the specific ordering code and package on the TI product page before release, as qualification varies by grade and suffix rather than by base part number alone.
Where to download the LM2902MT datasheet PDF?
The LM2902MT datasheet PDF is available from the Texas Instruments official product page at ti.com/product/LM2902, which hosts the latest revision of the datasheet along with application notes and quality information. Mirror copies are also hosted on datasheet aggregator sites, but always prefer the manufacturer's site to guarantee you have the current revision with up-to-date absolute maximum ratings and electrical characteristics.
Where can I find the LM2902MT pinout?
The LM2902MT follows the industry-standard 14-pin quad op-amp pinout: pins 1-3 are outputs and inputs of amplifier 1, pin 4 is VCC (positive supply), pins 5-7 serve amplifier 2, pins 8-10 serve amplifier 3, pin 11 is VEE/GND (negative rail), and pins 12-14 serve amplifier 4. The full pin-description table is in the Texas Instruments LM2902 datasheet; use it when assigning PCB tracks to the TSSOP-14 footprint.
Is the LM2902MT RoHS compliant?
Yes, the LM2902MT is RoHS compliant. The related ordering code LM2902MT/NOPB explicitly carries the /NOPB suffix, which Texas Instruments assigns to lead-free, RoHS-compliant versions of the part. Standard current production of the LM2902 family is lead-free and RoHS-compliant; for REACH, halogen-free, and conflict-minerals declarations for your specific shipment, request the compliance certificate through the Request a Quote form on this page.
How much does the LM2902MT cost and where can I buy it?
The LM2902MT is a commodity quad op-amp with pricing that varies by order quantity, packaging (tube versus tape and reel), and market conditions. For current unit pricing, stock availability, and lead time, submit the Request a Quote form on this page and the XAIPART team will respond with a formal quotation, including quantity-break pricing for your required volume and delivery schedule.
What is the lead time for LM2902MT?
The LM2902MT is a high-volume commodity amplifier that is typically available from authorized distribution stock, as evidenced by distributor listings showing this part shipping today. Stock and lead time change daily depending on allocation and demand. For the current stock position, factory lead time, and minimum order quantity for the tube-packed 14-TSSOP version, submit the Request a Quote form on this page for an accurate response.
What are the key specifications of the LM2902MT that engineers should know?
The LM2902MT is a quad op-amp in 14-TSSOP with four independent internally compensated amplifiers, a 1.2 MHz gain-bandwidth product, 2 mV typical input offset voltage, and supply operation up to 26 V total (single or split). It supports single-supply operation with input common-mode range including ground, uses tube packing, and is RoHS compliant. These parameters make it a workhorse for industrial signal conditioning, active filtering, and transducer interfacing at very low cost per channel.
When should I choose LM2902MT over a precision or faster op-amp?
Choose the LM2902MT when you need four general-purpose amplifiers at minimum cost in a single package, operate from a single supply up to 26 V, and your signal bandwidth stays well below the 1.2 MHz gain-bandwidth limit. Choose a precision amplifier when output accuracy below a few millivolts matters without trimming, or a higher-speed amplifier when closed-loop bandwidth demands exceed roughly 100 kHz at moderate gains. The LM2902MT wins on integration density, cost, and rail-to-ground input range for industrial front ends.

Impormasyon ng Talumpati sa Engineering for LM2902MT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the LM2902MT when you need four general-purpose op-amps on a single supply up to 26 V, at the lowest cost per channel, with the common-mode range extending to ground - the classic choice for industrial signal conditioning, transducer front ends, active filters, and slow threshold detection. Choose the LM2902MT/NOPB if your BOM requires the explicitly labeled RoHS/lead-free ordering code; it is the identical part. Choose the LM2902QPWRQ1 for automotive programs needing AEC-Q100 documentation, without changing the PCB. Consider the HGSEMI LM2902MT/TR for aggressive cost-down with a second source, after verifying its datasheet limits. Move to a precision or zero-drift amplifier if your output accuracy budget cannot tolerate 2 mV typical offset, or to a faster amplifier family if closed-loop bandwidths approach the 1.2 MHz gain-bandwidth limit at your target gain.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto LM2902MT/NOPB LM2902QPWRQ1 LM2902MT/TR LM324M
Package 14-TSSOP 14-TSSOP - same 14-TSSOP (PW) - same 14-TSSOP - same 14-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments HGSEMI Texas Instruments
Number of Circuits 4 4 4 4 4
Gain-Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz (per family) 1.2 MHz
Automotive Grade No (standard grade) No Yes (Q1) No No
Packaging Tube Tube Tape & Reel Tape & Reel Tape & Reel

Pangunahing mga Pagkakaiba

  • Automotive qualification option in the same footprint (kumpara saLM2902QPWRQ1)
  • Wider supply headroom than the LM324 commercial grade (kumpara saLM324M)
  • Four-channel integration density (kumpara saLM2902MT/TR (HGSEMI second source))

Talaan ng Disenyo

Decouple the VCC pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the device, plus 10 uF of bulk capacitance per board region. In split-supply use, decouple both VCC and VEE. The LM2902 output class-AB stages can draw load-current transients on all four channels simultaneously; inadequate local decoupling shows up as rail disturbance and crosstalk between the four amplifiers sharing the die.

Respect the output voltage swing limits: the LM2902 output cannot reach the positive rail, and phase reversal can occur if the input common-mode range is exceeded. Budget the 2 mV typical input offset at your closed-loop gain (about 200 mV output error at a gain of 100) in the accuracy calculation before selecting this part for precision DC duties. Do not drive capacitive loads heavier than roughly 100 pF directly without an isolation resistor, or the output stage may oscillate.

Keep feedback resistors close to the inverting input pins to minimize stray capacitance on the summing node, which erodes phase margin. Use a solid ground plane under the 14-TSSOP body and connect pin 11 (VEE/GND) directly to it. When configuring channels as comparators or high-gain stages, separate their routing from filter channels on the same die to avoid output-to-input crosstalk through shared supply impedance.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Yes
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

RoHS compliance indicated by the /NOPB (No Pb, lead-free) ordering variant of the same part; the LM2902MT is the lead-free RoHS option. AEC-Q100 qualification applies to Q1-grade variants (e.g. LM2902QPWRQ1), not the standard grade.

Data napatotohanan sa: 2026-11-08 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

LM2902MT datasheet LM2902MT datasheet pdf LM2902MT pinout lm2902mt nopb Texas Instruments LM2902MT LM2902MT equivalent LM2902MT replacement LM2902MT cross reference LM2902 vs LM324 LM2902MT price quad op amp 14-TSSOP 26V LM2902 application circuit

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments LM2902MT LM2902MT/NOPB LM2902QPWRQ1 LM324M HGSEMI LM2902 LM124 operational amplifier op-amp quad amplifier general purpose amplifier TSSOP-14 surface mount RoHS AEC-Q100 gain-bandwidth product input offset voltage single-supply operation industrial signal conditioning automotive sensor interface active filter
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ