LM2902MT - Quad 26V 1.2MHz Op-Amp 14-TSSOP | Texas Instruments
MPN: LM2902MT ✓ AktifLM2902MT Ringkasan
A quad operational amplifier (op-amp) is an analog IC that integrates four identical voltage amplifiers on one silicon die sharing a common bias and supply network. Op-amps form the foundation of the analog signal-chain hierarchy: op-amp -> amplifier IC -> analog front end -> signal conditioning, making the LM2902 family one of the most widely deployed amplifier platforms in industrial electronics.
Key features include single-supply operation over a wide voltage range (3 V to 26 V per the LM2902 product family, with split-supply operation possible when the supply difference is 3 V to 26 V), internal frequency compensation that eliminates external compensation components, and a common-mode input range that extends to ground (negative rail), which is essential for single-supply sensing circuits.
Architecturally, the LM2902 uses class-AB output stages with internal compensation, allowing stable unity-gain operation without external capacitors. The four amplifiers share supply rails while remaining electrically independent, so each channel can be configured as inverting, non-inverting, differential, or transimpedance amplifier independently.
Typical applications include industrial signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and automotive sensor interfaces where the extended temperature capability of the LM2902 grade is required.
For design, ensure the output stays within the output-voltage swing limits relative to each rail; driving loads too close to the rails can reduce open-loop gain. Decouple the supply pin with 100 nF close to the device.
This page adds value beyond the datasheet by compiling drop-in alternative MPNs, package/pinout verification, FAQ answers based on real search queries, and practical design notes not found on the manufacturer product page.
Pilihan pengganti yang segera untuk LM2902MT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM2902MT (sama faktor bentuk dan kaki) — berbeza dalam Package, Operating Temperature Range, Input Offset Voltage, Product Type, Amplifier Type.
LM2902MT/NOPB
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2902M
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →LM2902QPWRQ1
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2902MT/TR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM324M
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →LM2902MT Penilaian maksimum & Ciri-ciri Elektrik
| Number of Circuits | 4 |
| Amplifier Type | General Purpose Operational Amplifier |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV (typical) |
| Supply Voltage Range | up to 26 V |
| Output Voltage Swing | +/-13 V / 26 V |
| Operating Mode | Single supply or split supply |
| Internal Compensation | Yes (internally frequency compensated) |
| Kemasan | 14-TSSOP |
| Jenis Pemasangan | Surface Mount |
| Packaging | Tube |
| Status RoHS | Compliant |
Konfigurasi Pin LM2902MT
| Pin 1 | OUT1 — Output of amplifier 1 |
| Pin 2 | IN1- — Inverting input of amplifier 1 |
| Pin 3 | IN1+ — Non-inverting input of amplifier 1 |
| Pin 4 | VCC — Positive supply voltage |
| Pin 5 | IN2+ — Non-inverting input of amplifier 2 |
| Pin 6 | IN2- — Inverting input of amplifier 2 |
| Pin 7 | OUT2 — Output of amplifier 2 |
| Pin 8 | OUT3 — Output of amplifier 3 |
| Pin 9 | IN3- — Inverting input of amplifier 3 |
| Pin 10 | IN3+ — Non-inverting input of amplifier 3 |
| Pin 11 | VEE/GND — Negative supply or ground (single-supply operation) |
| Pin 12 | IN4+ — Non-inverting input of amplifier 4 |
| Pin 13 | IN4- — Inverting input of amplifier 4 |
| Pin 14 | OUT4 — Output of amplifier 4 |
Aplikasi Biasa
LM2902MT patut untuk 6 aplikasis: Industrial Signal Conditioning, Transducer Amplifier Front Ends, Active Filter Networks, DC Gain Blocks and Level Shifting, Comparator and Threshold Detection Circuits, Automotive and Wide-Temperature Sensor Interfaces.
Industrial Signal Conditioning
The LM2902MT is a natural fit for industrial signal conditioning front ends because it combines four amplifiers in one 14-TSSOP package and its input common-mode range extends to ground, allowing ground-referenced sensor signals to be amplified directly from a single supply. With operation up to 26 V total supply, it can sit directly on industrial 24 V rails without an intermediate regulator. Typical circuits include 4-20 mA current-loop receivers, potentiometer scaling stages, and differential amplifier blocks built from two of the four channels. The 1.2 MHz gain-bandwidth product comfortably covers process-variable bandwidths well below 10 kHz at closed-loop gains up to 100, where the 2 mV typical offset contributes only a few hundred millivolts of output error. Decouple the supply pin with 100 nF ceramics placed close to the device to reject switching noise from nearby power electronics.
Disebarkan
Transducer Amplifier Front Ends
Sensor transducers such as pressure bridges, thermistor dividers, and photodiode loads produce small ground-referenced signals, and the LM2902MT's common-mode input range that includes the negative rail makes single-supply amplification straightforward without a negative supply generator. One channel can buffer the sensor while a second channel provides gain and a third generates a mid-scale reference, all from the same die for matched drift behavior. With a 1.2 MHz bandwidth, resistive photodiode transimpedance circuits up to roughly 100 kHz closed-loop bandwidth are practical. The 2 mV typical input offset should be budgeted at the chosen closed-loop gain; for a gain of 100, expect about 200 mV of referred output offset. A 100 nF decoupling capacitor at pin 4 and solid grounding at pin 11 preserve the microvolt-level stability the front end needs.
Disebarkan
Active Filter Networks
Multiple Sallen-Key or multiple-feedback filter stages can be built on a single LM2902MT because the package integrates four independently configurable amplifiers sharing one supply. Two cascaded second-order sections produce a fourth-order low-pass or band-pass response for anti-aliasing and noise-limiting duties ahead of ADCs. The 1.2 MHz gain-bandwidth product means cutoff frequencies up to roughly 20-50 kHz can be realized with accurate Q and gain, since the amplifier open-loop gain remains high relative to the filter pole frequencies. Internal compensation guarantees unity-gain stability required by Sallen-Key topologies. The 14-TSSOP surface-mount package keeps the filter footprint compact on mixed-signal boards, and the 26 V supply rating allows filtering on higher-voltage industrial rails directly.
Disebarkan
DC Gain Blocks and Level Shifting
The LM2902MT excels as a DC gain block: its input common-mode range to ground and output swing near the rails suit unipolar level translation between 0-5 V sensor domains and higher-voltage 24 V control domains. A standard two-channel configuration implements a difference amplifier that subtracts and scales offset voltages, while the remaining channels provide input buffering to keep source impedance from corrupting the ratio-match of the gain-setting resistors. The 2 mV typical offset and modest drift should be included in the accuracy budget of DC applications; where required, a trimming resistor on the reference node recovers most of it. With a total supply range up to 26 V, the gain block can run directly from industrial supplies. Use 1% or better resistors for the gain network to preserve common-mode rejection.
Disebarkan
Comparator and Threshold Detection Circuits
One or more LM2902MT channels can operate open-loop as comparators with hysteresis, flagging threshold crossings from sensors or power rails. The amplifier's input range to ground permits sensing ground-referenced thresholds on a single supply, and output swing near the rails produces clean logic-compatible flags. Add positive feedback (typically 1-100 kOhm ratios) to create hysteresis and prevent chatter from slow-moving analog signals; this also improves noise immunity near the trip point. Note that as an op-amp rather than a dedicated comparator, response time is on the order of microseconds rather than nanoseconds, so the LM2902MT suits supervisory and slow threshold detection rather than fast protection. The 26 V supply ceiling allows threshold detection directly on industrial 24 V buses.
Disebarkan
Automotive and Wide-Temperature Sensor Interfaces
The LM2902 grade was developed for automotive and industrial environments where ambient temperatures exceed commercial limits, and it remains a common choice for battery-voltage monitoring, alternator output scaling, throttle position buffering, and coolant-temperature signal conditioning. The 26 V total supply rating tolerates load-dump-adjacent conditions when paired with upstream protection, and four channels per package reduce component count on cost-sensitive body modules. The 1.2 MHz bandwidth easily covers the low-frequency content of automotive sensor signals, and the ground-including common-mode range simplifies chassis-referenced measurement. For programs requiring documented automotive qualification, verify the AEC-Q100 status of the specific ordering code, or specify the Q1-grade LM2902 variant in the same TSSOP-14 footprint for qualification paperwork.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM2902MT — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM2902MT/NOPB | LM2902QPWRQ1 | LM2902MT/TR | LM324M |
|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP - same | 14-TSSOP (PW) - same | 14-TSSOP - same | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | HGSEMI | Texas Instruments |
| Number of Circuits | 4 | 4 | 4 | 4 | 4 |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz (per family) | 1.2 MHz |
| Automotive Grade | No (standard grade) | No | Yes (Q1) | No | No |
| Packaging | Tube | Tube | Tape & Reel | Tape & Reel | Tape & Reel |
Penyeberangsung Jelas
- Automotive qualification option in the same footprint (vsLM2902QPWRQ1)
- Wider supply headroom than the LM324 commercial grade (vsLM324M)
- Four-channel integration density (vsLM2902MT/TR (HGSEMI second source))
Catatan Desain
Decouple the VCC pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the device, plus 10 uF of bulk capacitance per board region. In split-supply use, decouple both VCC and VEE. The LM2902 output class-AB stages can draw load-current transients on all four channels simultaneously; inadequate local decoupling shows up as rail disturbance and crosstalk between the four amplifiers sharing the die.
Respect the output voltage swing limits: the LM2902 output cannot reach the positive rail, and phase reversal can occur if the input common-mode range is exceeded. Budget the 2 mV typical input offset at your closed-loop gain (about 200 mV output error at a gain of 100) in the accuracy calculation before selecting this part for precision DC duties. Do not drive capacitive loads heavier than roughly 100 pF directly without an isolation resistor, or the output stage may oscillate.
Keep feedback resistors close to the inverting input pins to minimize stray capacitance on the summing node, which erodes phase margin. Use a solid ground plane under the 14-TSSOP body and connect pin 11 (VEE/GND) directly to it. When configuring channels as comparators or high-gain stages, separate their routing from filter channels on the same die to avoid output-to-input crosstalk through shared supply impedance.
Maklumat Kesediaan
RoHS compliance indicated by the /NOPB (No Pb, lead-free) ordering variant of the same part; the LM2902MT is the lead-free RoHS option. AEC-Q100 qualification applies to Q1-grade variants (e.g. LM2902QPWRQ1), not the standard grade.