LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments
MPN: LM2903BIDGKR ✓ 啟用中LM2903BIDGKR 概覽
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a threshold. The LM2903B belongs to the comparator hierarchy within analog and power-management semiconductors. Unlike an operational amplifier, each channel does not require feedback compensation for linear amplification, and its open-collector output must connect to an external pull-up resistor when driving a logic input.
Key B-version improvements include lower offset voltage, lower input bias current, lower supply current, faster response, and stronger input protection than the original LM2903. The device features 0.37 mV input offset voltage, 3.5 nA input bias current, 200 μA supply current per comparator, 1 μs response time, and a 2 kV human-body-model ESD rating. Its outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer documentation.
Each internal comparator is electrically independent, but both channels share the supply pins and ground connection. Separate input and output pins allow one channel to perform threshold detection while the other performs window monitoring, current sensing, or another independent comparison. The open-collector architecture provides wired-AND behavior when multiple outputs share a pull-up node, although rise time then depends on the resistor, capacitance, and leakage current.
Typical uses include industrial sensor thresholding, battery and power-supply monitoring, overvoltage detection, signal conditioning, and embedded control systems. The wide 38 V maximum rating is useful in industrial environments where input transients can exceed nominal logic levels, but system designers must still validate signal levels and protection requirements for every operating condition.
For layout, route the comparator inputs away from switching nodes and place input-referred components close to their associated pins. Select the external output pull-up to balance sink-current capability against rise time. Verify input common-mode range, output pull-up voltage, package thermal conditions, and system shutdown behavior against the manufacturer datasheet before production release.
This page combines the LM2903B electrical characteristics, package and pin information, application guidance, design checks, and verified drop-in alternatives. It also highlights practical considerations for pull-up selection, input protection, noise, and industrial qualification that engineers can apply directly during schematic review and PCB design.
直接替換替代品,適用於 LM2903BIDGKR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2903BIDGKR (相同外形與佔位) — 差異在於 Comparator Type, Number of Channels, Output Type, Package.
LM2903AVQPWR
✅ 直接替換聯絡詢價
查看資料表 →LM2903BIDGKR 最大額定值與電氣特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 independent channels |
| Maximum Supply Voltage | 38 V |
| 工作電源電壓 | 2 V to 36 V |
| Input Common-Mode Voltage Range | Rail-to-rail |
| Differential Input Voltage Range | ±38 V |
| Input Offset Voltage | 0.37 mV maximum |
| Input Bias Current | 3.5 nA maximum |
| 供應電流 | 200 μA per comparator |
| Response Time | 1 μs |
| ESD Rating | 2 kV HBM |
| 輸出類型 | Open collector |
| Output Logic Compatibility | TTL, MOS, and CMOS |
| Qualification Class | Industrial grade |
| 封裝 | 8-pin VSSOP |
| 安裝類型 | Surface mount |
LM2903BIDGKR 腳位配置
| 腳位 1 | OUT1 — Comparator 1 open-collector output |
| 腳位 2 | IN1- — Comparator 1 inverting input |
| 腳位 3 | IN1+ — Comparator 1 noninverting input |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | IN2+ — Comparator 2 noninverting input |
| 腳位 6 | IN2- — Comparator 2 inverting input |
| 腳位 7 | OUT2 — Comparator 2 open-collector output |
| 腳位 8 | VCC — Positive supply connection |
典型應用
LM2903BIDGKR 適用於 6 應用s: Industrial Sensor Threshold Detection, Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Window and Limit Monitoring, Motor and Solenoid Current Sensing, Embedded Control Signal Conditioning.
Industrial Sensor Threshold Detection
The LM2903BIDGKR fits industrial sensor threshold detection because its two channels can monitor two independent signals while providing 0.37 mV maximum input offset voltage and 3.5 nA maximum input bias current. Connect one channel to a sensor signal and a precision reference to determine an upper or lower threshold. The dual architecture can monitor a second sensor or a validity signal without adding another comparator package. Because the comparator supports a 38 V maximum rated supply, it can interface with suitably protected industrial sensor lines. Add input clamps when wiring leaves the board, because the 38 V differential rating does not remove the need to control every input transient.
推薦
Power-Supply Overvoltage Detection
The LM2903BIDGKR is appropriate for power-supply overvoltage detection because it combines two independent channels with a 38 V maximum supply rating and 1 μs response time. One channel can compare a divided feedback voltage with a reference, while the other can monitor an auxiliary rail or UVLO condition. The open-collector output can pull a system-fault line low and remain compatible with CMOS or TTL logic when paired with the correct pull-up supply. Validate the divider tolerances, input filtering, and maximum monitored voltage so that startup overshoot cannot exceed the comparator's absolute-maximum limits.
推薦
Battery Voltage Monitoring
The LM2903BIDGKR can support battery voltage monitoring in industrial or high-voltage systems where a resistive divider brings the cell or pack voltage into the comparator input range. Its low 3.5 nA maximum input bias current reduces divider-loading error, while the 0.37 mV maximum offset helps preserve threshold accuracy after gain and reference errors are included. The two channels can monitor charge and discharge limits separately. Keep the divider current high enough to dominate input leakage, and protect the input pins from battery disconnection transients and high-energy fault events.
推薦
Window and Limit Monitoring
The two independent channels of the LM2903BIDGKR are well suited to window monitoring, where one output indicates a below-limit condition and the other indicates an above-limit condition. A divided sensor voltage can be compared against two reference levels, producing separate fault indications for excessive and insufficient system conditions. The 1 μs response time supports rapid threshold events, while the 200 μA supply current per comparator limits continuous overhead in battery-operated equipment. External pull-ups should be selected for the required fault-line rise time, and unused comparator inputs must be tied to a defined potential.
推薦
Motor and Solenoid Current Sensing
The LM2903BIDGKR can detect a current-shunt voltage and provide a digital fault signal for motor or solenoid control. Place the shunt near ground and compare the amplified or divided shunt voltage with a threshold reference, taking advantage of the comparator's 3.5 nA maximum input bias current to avoid significantly loading the sensing node. The second channel can monitor an overtemperature or driver-fault signal. Because switching nodes can produce fast transients, use a protection network and maintain a low-impedance return path from the shunt to the comparator ground.
推薦
Embedded Control Signal Conditioning
The LM2903BIDGKR converts an analog control or status signal into a logic decision for a microcontroller or programmable controller. Its dual-channel arrangement reduces component count when the controller needs both a rising threshold and a falling threshold, while the 1 μs response time provides rapid event capture. The 2 V to 36 V operating supply range supports industrial rails, and open-collector outputs permit wired fault signaling with an external pull-up. Confirm logic thresholds, input offsets, pull-up voltage, and grounding topology against the controller's electrical requirements before release.
推薦
推薦產品摘要
工程參考資料,適用於 LM2903BIDGKR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2903AVQPWR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin VSSOP | 8-pin VSSOP |
| Comparator Configuration | Dual differential | Dual differential |
| Output Type | Open collector | Open collector |
| Grade | Industrial grade | Automotive-oriented A-version grade |
主要差異化特點
- Improved B-version input accuracy (對比LM2903AVQPWR)
- Low input loading for high-impedance sensing (對比LM2903AVQPWR)
- Compact dual-channel implementation (對比LM2903AVQPWR)
設計說明
Do not treat the 38 V maximum supply rating as permission to apply 38 V continuously to every input. Check input common-mode limits, differential input limits, and absolute-maximum conditions separately, especially during power-up and shutdown. The open-collector outputs also require an external pull-up; omitting it can leave the connected logic input floating. Confirm that every unused comparator input is connected to a defined voltage rather than allowed to float.
Place input-divider resistors, reference components, and protection devices close to the comparator pins to minimize parasitic capacitance and susceptibility to injected noise. Keep the comparator ground connection short and return it to the quiet ground reference used by the sensed signal. For shunt-current sensing, use a dedicated low-impedance ground path from the shunt to the comparator ground instead of sharing a long return with switching loads.
Select the open-collector pull-up using three constraints: the output-low sink-current rating, the required logic rise time, and the pull-up voltage allowed by the connected device. A smaller pull-up improves rise time but increases sink current; a larger pull-up reduces current but slows the edge. Include bus capacitance and leakage when timing the rising transition, and use the datasheet's output-low voltage curve to verify the margin at the intended sink current.
The 200 μA-per-comparator supply current is low, but total system demand also includes input bias current, pull-up current, reference circuits, and external logic loads. Estimate the comparator's average dissipation as the supply voltage multiplied by the total device current, then include resistor-network loading separately. Provide adequate local bypassing at VCC and keep the supply return path short to limit transient coupling into the sensitive input nodes.
合規資訊
The LM2903BIDGKR is identified as industrial grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation. The LM2903AVQPWR alternative carries automotive-oriented grade considerations.