LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments
MPN: LM293DRG4 ✓ NakahandaLM293DRG4 Ulas
A comparator is an analog integrated circuit that evaluates two voltages and changes its output state when one input crosses the other. Within the signal-chain hierarchy, the LM293 belongs to the comparator class, which sits alongside amplifiers and other analog interface ICs used to convert continuous voltage relationships into binary logic decisions. The LM293's open-collector outputs are useful when a system needs a pulled-up logic signal, wired logic, level translation, or an adjustable output rise time.
The LM293 family is specified as a dual differential comparator for industrial applications. The LM293DRG4 ordering code identifies the 8-SOIC package and tape-and-reel shipping configuration. Its two channels are independent, allowing one device to implement two threshold decisions. Open-collector outputs also permit multiple devices to share a common pull-up bus when the system designer confirms that the resulting wired-AND behavior is intentional.
The device can operate from a single supply or from positive and negative supplies. The manufacturer states that the common-mode input range includes ground, that the differential input range equals the maximum-rated supply voltage, and that the output is compatible with TTL, MOS, and CMOS logic. The LM293B version is identified as a drop-in replacement for LM293, LM393, and LM2903 families, providing a useful basis for qualified equivalent selection.
Typical applications include power-supply threshold detection, sensor-signal conditioning, industrial control interfaces, battery monitoring, and digital logic level translation. In a sensor interface, the non-inverting input can receive a reference voltage while the inverting input receives the sensed signal, allowing the open-collector output to indicate when the signal crosses the selected threshold. The output requires an external pull-up because the LM293 does not actively drive its output high.
Designers should account for input offset voltage, common-mode limits, supply voltage, output pull-up resistance, and propagation delay. Input components should also prevent excessive differential input voltage and protect sensitive sensor nodes from electrostatic discharge. Because the output is open collector, the pull-up resistor and its placement materially affect rise time, power consumption, and susceptibility to interference.
This page combines the LM293 family architecture, verified ordering and package information, practical replacement criteria, threshold-comparison guidance, and PCB-focused design considerations. It also distinguishes genuine pin-compatible choices from options that require changes to output pull-ups, supply arrangements, or board layout.
Mga alternatibo na pwedeng ilagay na LM293DRG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM293DRG4 (parehas na form factor at footprint) — pagkakaiba sa Common-Mode Input Range, Comparator Type, Output Compatibility, Output Type, Package.
LM293ADRG4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
LM293DG
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →LM293DG4
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM293BDRG4
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM2903BDRG4
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM293DRG4 Mga Pinakamataas na Rating at Electrical Characteristics
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Type ng Output | Open-collector |
| Dual-Supply Total Voltage Difference | 2 V to 36 V |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | Equal to maximum-rated supply voltage |
| Input Offset Voltage, Maximum | 9000 uV |
| Maximum Operating Temperature | 85 C |
| Output Compatibility | TTL, MOS, and CMOS compatible |
| Packhaging | 8-SOIC, 3.90 mm nominal width |
| Uri ng Pagpapasok | Surface mount |
| Shipping Configuration | Tape and reel |
| Industrial Grade | Yes |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Gabay sa Pin Configuration ng LM293DRG4 8-soic, 3.90 mm nominal width
Pin configuration para sa LM293DRG4 (8-soic, 3.90 mm nominal width package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM293DRG4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM293DRG4 ay nararapat para sa 6 aplikasyons: Power-Supply Threshold Detection, Industrial Sensor Interfaces, Battery Monitoring, Digital Logic Level Translation, Window and Limit Comparators, Relay and Alarm Control.
Power-Supply Threshold Detection
The LM293DRG4 fits power-supply supervision because its dual differential channels compare two input voltages and produce open-collector logic states. One channel can monitor a feedback or divided supply node against a reference, while the other can perform an independent overvoltage or undervoltage decision. The 8-SOIC package keeps both channels together, and the family supports single-supply operation with a common-mode input range that includes ground. The external pull-up should reference the supervisory logic rail. This arrangement avoids an active-high output driver, but it requires careful selection of the pull-up resistor so the rising edge remains fast enough for the downstream supervisor.
Inirekomenda
Industrial Sensor Interfaces
The LM293DRG4 is appropriate for industrial sensor interfaces that convert an analog measurement into a threshold event. A sensor output can drive one input while a precision reference drives the other, and the comparator then identifies when the measured quantity crosses the selected limit. Two independent channels can monitor two variables, such as a temperature threshold and a fault signal. The open-collector output can drive a pull-up and an alarm input, while the reported maximum input offset voltage of 9000 uV must be included when sizing the measurement span. Industrial use also requires checking the stated 85 C maximum operating temperature against the enclosure's worst-case ambient.
Inirekomenda
Battery Monitoring
The LM293DRG4 can implement discrete battery-voltage threshold checks without relying on a complex digital monitor. A resistor-divider network can scale the battery voltage into the common-mode range, after which a comparator channel determines whether the battery is above or below a selected reference. Its open-collector output is useful for combining the comparison with an enable, charger inhibit, or status indicator. The LM293 family's common-mode input range includes ground, which supports monitoring near the lower end of a supply. Designers should verify the exact single-supply limits, account for the 9000 uV maximum input offset, and ensure that the divider's tolerances do not dominate the threshold accuracy.
Inirekomenda
Digital Logic Level Translation
The LM293DRG4 can support level translation when the source uses an open-collector output and the destination requires a CMOS high level. Pull the collector to the destination logic rail rather than the source rail, allowing the comparator to recognize the input condition while presenting a valid high voltage to the receiving gate. Two channels can handle two translated signals, reducing package count. The external pull-up remains essential because the LM293 cannot source output current in the high state. Its stated compatibility with TTL, MOS, and CMOS logic makes the interface broadly useful, although input levels, output timing, and supply limits must remain within the exact LM293 ordering variant's ratings.
Inirekomenda
Window and Limit Comparators
The two LM293DRG4 channels can implement a two-threshold window comparator when each channel receives a different reference or polarity relationship. This arrangement can indicate whether a measured signal lies below, inside, or above a permitted interval, which is useful for process control and equipment protection. The open-collector outputs can be pulled up and logically combined where wired-AND behavior is acceptable. Because the channels are independent, each can evaluate a different limit without shared internal state. A real implementation should calculate resistor-divider tolerances, comparator offset, input bias effects, and propagation delay before treating the thresholds as precise production limits.
Inirekomenda
Relay and Alarm Control
The LM293DRG4 can generate an active-low control or alarm signal for a relay driver, buzzer, or fault indicator. The relevant input pair senses a system condition, and the open-collector output pulls its pulled-up node low when the condition is detected. The dual-channel configuration allows independent monitoring of a primary fault and a secondary limit. Its open-collector architecture is particularly useful when several wired logic signals share a common pull-up node. Protection diodes, relay snubbers, and driver-transistor selection remain outside the comparator, so the complete actuator circuit must be engineered for inductive loads and isolation requirements rather than relying only on the comparator's output ratings.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM293DRG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM293ADRG4 | LM293DG | LM293DG4 | LM293BDRG4 | LM2903BDRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Comparator Configuration | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Pangunahing mga Pagkakaiba
- Two independent channels in one 8-SOIC package (kumpara saLM2904PWR)
- Open-collector output supports flexible pull-up logic (kumpara saLM2904PWR)
- Dual-supply flexibility of 2 V to 36 V total difference (kumpara saLM293DG)
Talaan ng Disenyo
Do not treat an open-collector output as a push-pull logic output. Connect a suitable pull-up resistor from each output to the receiving logic rail, and include the resistor's contribution to output rise time when the connected input is capacitive. A value that is too large can create a slow or noisy high transition, while a value that is too small can increase supply current and overload the output transistor.
Keep the two inputs and the comparator ground connection compact on the PCB. Input traces should be short and physically separated from switching nodes and high-current paths to reduce differential noise pickup. When using long sensor wiring, place protection and filtering near the connector, and account for the reported maximum input offset voltage of 9000 uV when defining the smallest useful threshold difference.
Decouple the comparator supply with a local ceramic capacitor and provide adequate return-current continuity to the device ground. Check the exact absolute maximum and operating supply limits in the Texas Instruments LM293 datasheet before selecting the rail. The open-collector pull-up may draw current continuously when the output is low, so include that load in the supply budget when the output remains asserted for long periods.
Impormasyon ng Pagsunod sa Kautusan
The component is described by Texas Instruments as an industrial-grade dual differential comparator. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the source data.