Texas Instruments

LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments

MPN: LM293DRG4 ✓ فعال
2 V to 36 V Vdss 8-SOIC, 3.90 mm nominal width Package
MOQ: 1 |

LM293DRG4 جائزہ

The Texas Instruments LM293DRG4 is a dual differential comparator with two independent channels, open-collector outputs, and an 8-pin SOIC package. It supports single-supply operation over a wide voltage range and dual-supply operation when the total supply difference is between 2 V and 36 V. Each channel compares an inverting input with a non-inverting input and provides a logic-compatible indication of the input relationship.

A comparator is an analog integrated circuit that evaluates two voltages and changes its output state when one input crosses the other. Within the signal-chain hierarchy, the LM293 belongs to the comparator class, which sits alongside amplifiers and other analog interface ICs used to convert continuous voltage relationships into binary logic decisions. The LM293's open-collector outputs are useful when a system needs a pulled-up logic signal, wired logic, level translation, or an adjustable output rise time.

The LM293 family is specified as a dual differential comparator for industrial applications. The LM293DRG4 ordering code identifies the 8-SOIC package and tape-and-reel shipping configuration. Its two channels are independent, allowing one device to implement two threshold decisions. Open-collector outputs also permit multiple devices to share a common pull-up bus when the system designer confirms that the resulting wired-AND behavior is intentional.

The device can operate from a single supply or from positive and negative supplies. The manufacturer states that the common-mode input range includes ground, that the differential input range equals the maximum-rated supply voltage, and that the output is compatible with TTL, MOS, and CMOS logic. The LM293B version is identified as a drop-in replacement for LM293, LM393, and LM2903 families, providing a useful basis for qualified equivalent selection.

Typical applications include power-supply threshold detection, sensor-signal conditioning, industrial control interfaces, battery monitoring, and digital logic level translation. In a sensor interface, the non-inverting input can receive a reference voltage while the inverting input receives the sensed signal, allowing the open-collector output to indicate when the signal crosses the selected threshold. The output requires an external pull-up because the LM293 does not actively drive its output high.

Designers should account for input offset voltage, common-mode limits, supply voltage, output pull-up resistance, and propagation delay. Input components should also prevent excessive differential input voltage and protect sensitive sensor nodes from electrostatic discharge. Because the output is open collector, the pull-up resistor and its placement materially affect rise time, power consumption, and susceptibility to interference.

This page combines the LM293 family architecture, verified ordering and package information, practical replacement criteria, threshold-comparison guidance, and PCB-focused design considerations. It also distinguishes genuine pin-compatible choices from options that require changes to output pull-ups, supply arrangements, or board layout.

کے لیے ڈراپ اِن متبادل LM293DRG4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM293DRG4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Common-Mode Input Range, Comparator Type, Output Compatibility, Output Type, Package.

onsemi
Common-Mode Input Range: Includes ground (single supply operation)
Comparator Type: Precision, dual, independent
Output Compatibility: CMOS, MOS, TTL, DTL, ECL
موازنہ کریں LM293DRG4 →

LM293ADRG4

✅ ڈراپ-اِن
📦 8-SOIC
Uses the LM293A grade; maximum input offset voltage differs from the LM293DRG4's 9000 uV rating, while the 8-SOIC open-collector architecture remains.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM293DG

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
onsemi
📦 8-SOIC
Precision, dual, independent · 2 · 2 V to 36 V · -25 C to +85 C · as low as 2.0 mV · 1.3 microseconds · 400 microamps · Open-collector / open-drain

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM293DG4

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
Tape-and-reel ordering variant of the LM293 family with the same 8-SOIC footprint and dual comparator function.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM293BDRG4

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
LM293B grade provides improved specifications relative to LM293 while retaining the 8-SOIC footprint and open-collector output.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM2903BDRG4

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
LM2903B is identified as a drop-in replacement family for LM293 but has a different temperature-grade positioning; the 8-SOIC footprint is retained.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM293DRG4 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Comparator Type Dual differential comparator
Number of Channels 2 channels
آؤٹ پٹ کی قسم Open-collector
Dual-Supply Total Voltage Difference 2 V to 36 V
Common-Mode Input Range Includes ground
Differential Input Voltage Range Equal to maximum-rated supply voltage
Input Offset Voltage, Maximum 9000 uV
Maximum Operating Temperature 85 C
Output Compatibility TTL, MOS, and CMOS compatible
پیکیج 8-SOIC, 3.90 mm nominal width
ماؤنٹنگ ٹائپ Surface mount
Shipping Configuration Tape and reel
Industrial Grade Yes
RoHS اسٹیٹس unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

LM293DRG4 8-soic, 3.90 mm nominal width پن کنفیگریشن گائیڈ

LM293DRG4 (8-soic, 3.90 mm nominal width پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

LM293DRG4 کے لیے 8-soic, 3.90 mm nominal width پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM293DRG4.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

LM293DRG4 کے لیے موزوں ہے 6 ایپلیکیشنs: Power-Supply Threshold Detection, Industrial Sensor Interfaces, Battery Monitoring, Digital Logic Level Translation, Window and Limit Comparators, Relay and Alarm Control.

⚡

Power-Supply Threshold Detection

The LM293DRG4 fits power-supply supervision because its dual differential channels compare two input voltages and produce open-collector logic states. One channel can monitor a feedback or divided supply node against a reference, while the other can perform an independent overvoltage or undervoltage decision. The 8-SOIC package keeps both channels together, and the family supports single-supply operation with a common-mode input range that includes ground. The external pull-up should reference the supervisory logic rail. This arrangement avoids an active-high output driver, but it requires careful selection of the pull-up resistor so the rising edge remains fast enough for the downstream supervisor.

🏭

Industrial Sensor Interfaces

The LM293DRG4 is appropriate for industrial sensor interfaces that convert an analog measurement into a threshold event. A sensor output can drive one input while a precision reference drives the other, and the comparator then identifies when the measured quantity crosses the selected limit. Two independent channels can monitor two variables, such as a temperature threshold and a fault signal. The open-collector output can drive a pull-up and an alarm input, while the reported maximum input offset voltage of 9000 uV must be included when sizing the measurement span. Industrial use also requires checking the stated 85 C maximum operating temperature against the enclosure's worst-case ambient.

📱

Battery Monitoring

The LM293DRG4 can implement discrete battery-voltage threshold checks without relying on a complex digital monitor. A resistor-divider network can scale the battery voltage into the common-mode range, after which a comparator channel determines whether the battery is above or below a selected reference. Its open-collector output is useful for combining the comparison with an enable, charger inhibit, or status indicator. The LM293 family's common-mode input range includes ground, which supports monitoring near the lower end of a supply. Designers should verify the exact single-supply limits, account for the 9000 uV maximum input offset, and ensure that the divider's tolerances do not dominate the threshold accuracy.

🖥️

Digital Logic Level Translation

The LM293DRG4 can support level translation when the source uses an open-collector output and the destination requires a CMOS high level. Pull the collector to the destination logic rail rather than the source rail, allowing the comparator to recognize the input condition while presenting a valid high voltage to the receiving gate. Two channels can handle two translated signals, reducing package count. The external pull-up remains essential because the LM293 cannot source output current in the high state. Its stated compatibility with TTL, MOS, and CMOS logic makes the interface broadly useful, although input levels, output timing, and supply limits must remain within the exact LM293 ordering variant's ratings.

🔧

Window and Limit Comparators

The two LM293DRG4 channels can implement a two-threshold window comparator when each channel receives a different reference or polarity relationship. This arrangement can indicate whether a measured signal lies below, inside, or above a permitted interval, which is useful for process control and equipment protection. The open-collector outputs can be pulled up and logically combined where wired-AND behavior is acceptable. Because the channels are independent, each can evaluate a different limit without shared internal state. A real implementation should calculate resistor-divider tolerances, comparator offset, input bias effects, and propagation delay before treating the thresholds as precise production limits.

🔧

Relay and Alarm Control

The LM293DRG4 can generate an active-low control or alarm signal for a relay driver, buzzer, or fault indicator. The relevant input pair senses a system condition, and the open-collector output pulls its pulled-up node low when the condition is detected. The dual-channel configuration allows independent monitoring of a primary fault and a secondary limit. Its open-collector architecture is particularly useful when several wired logic signals share a common pull-up node. Protection diodes, relay snubbers, and driver-transistor selection remain outside the comparator, so the complete actuator circuit must be engineered for inductive loads and isolation requirements rather than relying only on the comparator's output ratings.

What is the LM293DRG4?
The LM293DRG4 is a Texas Instruments dual differential comparator with two independent channels, open-collector outputs, and an 8-SOIC package. It is intended for general-purpose industrial signal comparison and can operate from a single supply or from positive and negative supplies whose total difference is 2 V to 36 V. The two channels allow independent threshold decisions in one package.
What is the supply voltage range of LM293DRG4?
The LM293DRG4 supports a single supply or dual supplies with a total voltage difference from 2 V to 36 V. Its common-mode input range includes ground, and its differential input range equals the maximum-rated supply voltage. Exact single-supply operating limits and absolute maximum ratings should be confirmed against the Texas Instruments LM293 datasheet before final circuit design.
Why does LM293DRG4 need an external pull-up resistor?
The LM293DRG4 has open-collector outputs, so the output transistor can pull the node low but cannot actively drive it high. An external pull-up resistor connected to the desired logic supply completes the circuit and establishes the high state. The resistor value also controls output rise time, power use, and sensitivity to capacitive loading, so it must be selected for the connected logic interface.
Where can I download the LM293DRG4 datasheet PDF?
The official Texas Instruments LM293 product page is the preferred starting point for the LM293DRG4 datasheet and ordering information. It is available at https://www.ti.com/product/LM293. The LM293DRG4 is the 8-SOIC tape-and-reel ordering variant of the dual differential comparator family, so the family document applies to its electrical characteristics.
Where can I find the LM293DRG4 pinout?
Use the pin-description diagram and ordering information in the Texas Instruments LM293 datasheet to assign PCB tracks for the 8-SOIC package. The LM293DRG4 has eight pins, and its two comparator channels require separate non-inverting and inverting inputs, two outputs, a supply connection, and ground. Verify the exact numbering against the current manufacturer document before releasing a PCB layout.
What is the LM293DRG4 output type and logic compatibility?
The LM293DRG4 uses an open-collector output and is compatible with TTL, MOS, and CMOS logic according to the Texas Instruments LM293 family information. Each output can indicate whether its non-inverting input is above or below its inverting input. Because the collector is not actively driven high, the external pull-up voltage and resistor determine the usable logic levels.
LM293DRG4 vs LM393DRG4 - which is better?
The LM293DRG4 is the original LM293-family dual differential comparator, while the LM393 is a closely related comparator family. Texas Instruments identifies the LM293B as a drop-in replacement for LM293, LM393, and LM2903, indicating strong functional and pin compatibility. The selection should still consider the exact suffix electrical limits, temperature grade, and any required PCB or qualification review.
Can LM2903 replace LM293DRG4?
A properly packaged LM2903-family comparator can serve as a close functional alternative, and Texas Instruments identifies the LM293B as a drop-in replacement for LM293, LM393, and LM2903. However, the exact ordering suffix determines package, temperature range, and electrical limits. Confirm pin assignments and critical parameters in the candidate's own manufacturer datasheet before treating it as a drop-in replacement.
When should I choose LM293DRG4 over a B-version comparator?
Choose the LM293DRG4 when an existing design specifies the original LM293 electrical profile and an 8-SOIC footprint, particularly if qualification is tied to that exact device. Choose a B-version alternative when its improved specifications are needed and the manufacturer confirms drop-in compatibility. The B version can offer refreshed behavior, but it should not be substituted solely on the basis of the shared SOIC package.
What is the best drop-in replacement for LM293DRG4?
The best replacement is the candidate that matches the 8-SOIC pinout, open-collector output, supply range, input range, temperature class, and propagation-delay requirements. LM293-family and related TI options are natural starting points, while cross-brand choices require manufacturer or distributor cross-reference confirmation. Use the Texas Instruments LM293 product page to establish the original device's ordering and comparison basis.
Is LM293DRG4 suitable for industrial control systems?
The LM293DRG4 is identified as an industrial-grade dual differential comparator and is packaged in an 8-SOIC surface-mount format. It is suitable for industrial threshold detection, sensor interfaces, and control logic when operated within its specified electrical and temperature limits. The listing associated with this part identifies a maximum operating temperature of 85 C, which must be checked against system requirements.
How should an open-collector comparator output be interfaced with CMOS?
Connect the open-collector output to a suitable pull-up resistor referenced to the CMOS supply, normally the same rail used by the receiving logic. Confirm that the pull-up voltage remains within the comparator's output limits and that its high level satisfies the receiving device's input threshold. A resistor that is too large produces a slow rising edge; one that is too small increases supply current and may overload the output transistor.
What are the key specifications of LM293DRG4 that engineers should know?
The LM293DRG4 is a dual, independent differential comparator in an 8-SOIC package with open-collector outputs. Key family-level characteristics include operation from a single supply or from dual supplies separated by 2 V to 36 V, a common-mode range including ground, and compatibility with TTL, MOS, and CMOS logic. The associated technical listing reports a maximum input offset voltage of 9000 uV and a maximum operating temperature of 85 C.
Where to buy LM293DRG4 online?
Use the Request a Quote form on this page to ask about LM293DRG4 availability, minimum order quantity, and lead time. Quote-based sourcing is appropriate because current inventory and commercial terms can change quickly. The verified product listing identifies an 8-SOIC, tape-and-reel configuration, which should be confirmed when the supplier prepares a quotation for production quantities.
What is the price and lead time of LM293DRG4?
The current commercial terms for LM293DRG4 should be obtained through the Request a Quote form on this page rather than from a static product description. The request should specify the required quantity, 8-SOIC tape-and-reel packaging, and destination. The manufacturer product page and distributor listings identify the part and its commercial availability, but current price, stock, and lead time require a direct quotation.

کے لیے انجینئرنگ ریفرنس ڈیٹا LM293DRG4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose LM293DRG4 for new 8-SOIC industrial designs that require two independent differential comparisons, open-collector outputs, and operation from a single supply or from positive and negative rails with a total difference of 2 V to 36 V. Its common-mode range includes ground, making it suitable for threshold detection near the lower rail, while TTL, MOS, and CMOS output compatibility supports broad digital-interface use. Consider LM293ADRG4 when the A-grade electrical profile is preferable, LM293BDRG4 when refreshed B-version characteristics are advantageous, and LM2903BDRG4 when its temperature-grade positioning better matches the deployment. Every proposed substitute must retain the 8-SOIC footprint, open-collector output behavior, input and supply limits, and required temperature rating. Existing production designs should also validate output pull-up values, threshold accuracy, timing, and any qualification requirements before substitution.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ LM293ADRG4 LM293DG LM293DG4 LM293BDRG4 LM2903BDRG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Comparator Configuration Dual differential Dual differential Dual differential Dual differential Dual differential Dual differential
Number of Channels 2 2 2 2 2 2
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector

اہم امتیازی خصوصیات

  • Two independent channels in one 8-SOIC package (بمقابلہLM2904PWR)
  • Open-collector output supports flexible pull-up logic (بمقابلہLM2904PWR)
  • Dual-supply flexibility of 2 V to 36 V total difference (بمقابلہLM293DG)

ڈیزائن نوٹس

Do not treat an open-collector output as a push-pull logic output. Connect a suitable pull-up resistor from each output to the receiving logic rail, and include the resistor's contribution to output rise time when the connected input is capacitive. A value that is too large can create a slow or noisy high transition, while a value that is too small can increase supply current and overload the output transistor.

Keep the two inputs and the comparator ground connection compact on the PCB. Input traces should be short and physically separated from switching nodes and high-current paths to reduce differential noise pickup. When using long sensor wiring, place protection and filtering near the connector, and account for the reported maximum input offset voltage of 9000 uV when defining the smallest useful threshold difference.

Decouple the comparator supply with a local ceramic capacitor and provide adequate return-current continuity to the device ground. Check the exact absolute maximum and operating supply limits in the Texas Instruments LM293 datasheet before selecting the rail. The open-collector pull-up may draw current continuously when the output is low, so include that load in the supply budget when the output remains asserted for long periods.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The component is described by Texas Instruments as an industrial-grade dual differential comparator. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the source data.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-15 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

LM293DRG4 datasheet LM293DRG4 pinout LM293DRG4 datasheet pdf Texas Instruments LM293DRG4 LM293DRG4 equivalent LM293DRG4 replacement LM293DRG4 cross reference LM293DRG4 vs LM293ADRG4 LM293DRG4 price LM293DRG4 stock LM293 8-SOIC open collector comparator LM293DRG4 industrial sensor interface

متعلقہ اجزاء اور اصطلاحات

Texas Instruments LM293DRG4 LM293 LM293A LM293B LM2903 LM393 dual differential comparator comparator IC analog interface IC open-collector output TTL compatible MOS compatible CMOS compatible common-mode input range differential input voltage input offset voltage 8-SOIC SOIC package family surface-mount package industrial electronics power-supply supervision sensor threshold detection battery monitoring logic level translation
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں