LM358BPX - Dual 36V 1.2MHz Op Amp | Texas Instruments
MPN: LM358BPX ✓ NakahandaLM358BPX Ulas
An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, signal-conditioning ICs, and analog front-end components. Its two independent channels permit simultaneous processing of related signals without requiring two separate single-channel packages.
The principal LM358B-family characteristics include operation from a single supply or from split positive and negative supplies, a 1.2 MHz unity-gain bandwidth, a 0.5 V/us slew rate, and a 3 mV maximum input-offset voltage. According to the TI LM358B product page, the commercial-temperature family operates from -40°C to 85°C. These characteristics place the amplifier between precision low-noise amplifiers and high-speed operational amplifiers: it offers useful DC accuracy and common-mode flexibility without the bandwidth of a high-speed comparator or precision amplifier.
Each channel includes one input stage, an output stage, and compensation circuitry. The two amplifiers are independent rather than internally linked, allowing the same package to implement independent gain stages, comparators, buffers, or transducers. The 0.5 V/us slew rate limits how quickly a large output transition can occur, while the 1.2 MHz gain-bandwidth product limits closed-loop bandwidth as feedback gain increases. A practical gain-bandwidth relationship of 1.2 MHz divided by noise gain gives a useful first estimate of usable bandwidth.
Typical uses include temperature-sensor signal conditioning, audio preamplification, DC motor-current monitoring, industrial sensor interfaces, low-frequency active filters, and power-supply feedback. For sensor applications, the 3 mV offset specification is important because input-referred offset appears directly at the amplifier output after multiplication by the closed-loop noise gain. In AC-coupled audio paths, the slew rate and bandwidth determine whether large low-frequency signals can be reproduced without excessive distortion.
PCB design should prioritize short input and feedback paths, a stable output connection, and careful bypassing of the positive supply. Because the LM358BPX uses a compact ball-grid package, the manufacturer land pattern and pin-description table should govern assembly and inspection. Decoupling capacitors should be placed close to the supply and ground balls, while analog input traces should be kept away from switching nodes and high-current return paths.
This page combines the LM358B family electrical characteristics, LM358BPX package information, pin assignments, verified source links, and practical guidance for analog-board design. It also identifies the limits of direct substitution: many LM358 equivalents use DIP or SOIC packages rather than the LM358BPX 8-ball VFBGA footprint, so a functional match does not necessarily qualify as a PCB drop-in replacement.
Mga alternatibo na pwedeng ilagay na LM358BPX — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboLM358BPX Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Channels | 2 channels |
| Amplifier Type | Dual general-purpose operational amplifier |
| Maximum Supply Voltage | 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 3 mV maximum |
| Slew Rate | 0.5 V/us |
| Input Bias Current | 10 nA |
| Temperature na Operasyon | -40°C to 85°C |
| Packhaging | 8-VFBGA |
| Terminal Count | 8 terminals |
| Uri ng Pagpapasok | Surface mount |
| Package Shape | Square |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
Pin Configuration ng LM358BPX
| Pin 1 | OUT A — Channel A output |
| Pin 2 | IN A- — Channel A inverting input |
| Pin 3 | IN A+ — Channel A non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN B+ — Channel B non-inverting input |
| Pin 6 | IN B- — Channel B inverting input |
| Pin 7 | OUT B — Channel B output |
| Pin 8 | V+ — Positive supply connection |
Tipikal na mga Gamit
LM358BPX ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Audio Preamplification and Buffering, Power-Supply Feedback and Control, Temperature and Pressure Transducer Interface, Low-Frequency Active Filters, Motor Current Monitoring.
Industrial Sensor Signal Conditioning
The LM358BPX fits low-frequency current, voltage, and resistive sensor interfaces because each channel provides a 1.2 MHz gain-bandwidth product, 10 nA input-bias current, and a 36 V maximum supply rating. One channel can amplify a sensor signal while the other forms a buffer, gain stage, or active filter. Its 3 mV input-offset rating matters at higher noise gains, where offset error is multiplied by the closed-loop gain. The principal design check is common-mode range: the selected supply arrangement must keep both input pins inside the amplifier’s permitted operating region.
Inirekomenda
Audio Preamplification and Buffering
The LM358BPX is appropriate for modest-bandwidth audio preamplifier and buffering stages requiring two independent channels. A 1.2 MHz gain-bandwidth product provides useful response well above the audio band, while the 0.5 V/us slew rate constrains large-amplitude transitions. For microphone or line-level inputs, configure each channel with feedback resistors, bypass the supply near pins 8 and 4, and keep input traces short. Verify output swing against the chosen single-supply level and use input coupling capacitors when the source is biased around ground.
Inirekomenda
Power-Supply Feedback and Control
LM358BPX can monitor a regulated rail or participate in a low-frequency feedback loop because the 1.2 MHz gain-bandwidth product is substantially above typical control-loop bandwidth and the device supports supply operation up to 36 V. One channel may amplify a divided feedback voltage, while the other compares or amplifies the error signal. Compensation must be chosen around the actual amplifier bandwidth, output loading, and power-stage characteristics rather than around the 0.5 V/us slew rate alone. Decoupling and layout remain essential because injected supply ripple can otherwise appear as output disturbance.
Inirekomenda
Temperature and Pressure Transducer Interface
The LM358BPX supports resistive temperature-sensor and pressure-transducer interfaces where low input bias and moderate bandwidth are useful. Its 10 nA input-bias current produces less loading on high-resistance sensing elements than a general-purpose bipolar input with higher bias current. One channel can provide excitation buffering while the other amplifies the differential output. The 3 mV offset rating must be included in total error analysis, particularly at high gain or when the bridge excitation is low. The 36 V supply ceiling also allows operation from industrial rails when the common-mode limits are respected.
Inirekomenda
Low-Frequency Active Filters
The two LM358BPX channels can implement a second-order Sallen-Key filter or two separate first-order sections. At a noise gain of 10, the 1.2 MHz gain-bandwidth product implies a first-order gain-bandwidth limit of approximately 120 kHz, before allowing additional margin for component tolerances and phase error. The 0.5 V/us slew rate also affects large-signal behavior, particularly at low frequencies and high output amplitude. Because the package is compact, place input and feedback components close to their associated balls and avoid routing sensitive filter nodes beneath digital or switching circuitry.
Inirekomenda
Motor Current Monitoring
The LM358BPX can amplify a low-voltage motor-current-shunt signal in industrial or appliance control systems. Its 36 V maximum supply rating provides headroom for operation from a 24 V rail, and the 1.2 MHz bandwidth is well above typical motor-current control bandwidths. The shunt amplifier must preserve the common-mode voltage presented to the inputs, so the shunt placement and amplifier supply configuration need to be evaluated together. The 3 mV offset becomes a shunt-voltage error after gain multiplication; specify an appropriate shunt resistance and gain to preserve useful measurement resolution.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM358BPX — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Texas Instruments |
| Package | 8-VFBGA |
| Channel Count | 2 channels |
| Maximum Supply Voltage | 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/us |
| Input Offset Voltage | 3 mV maximum |
| Input Bias Current | 10 nA |
| Operating Temperature | -40°C to 85°C |
Talaan ng Disenyo
Use the manufacturer’s 8-VFBGA land pattern and ball-orientation markings without modification. Place the positive-supply bypass capacitor directly between the V+ ball and the ground reference, and provide a local return path that does not force input currents through the amplifier ground connection. Keep the two channels’ feedback networks compact and route each channel’s inputs away from adjacent switching or high-current paths.
Do not infer common-mode or output-swing limits solely from the 36 V maximum supply rating. For a single 5 V supply, verify that the input and output voltages remain within the electrical limits stated in the datasheet for that supply configuration. Also remember that the 3 mV input offset is multiplied by the closed-loop noise gain, so high-gain sensor designs should include that value in their error budget.
Choose the closed-loop bandwidth from the 1.2 MHz gain-bandwidth product and the selected noise gain, then leave additional margin for gain tolerance and phase shift. The 0.5 V/us slew rate also sets a large-signal limit. This is normally adequate for low-frequency industrial and audio stages, but it can become the limiting factor in fast edge, communications, or waveform-generation applications.
Impormasyon ng Pagsunod sa Kautusan
The available manufacturer and distributor pages do not establish the requested compliance statuses for this exact LM358BPX order code. The -40°C to 85°C rating identifies a commercial-temperature device but does not by itself establish AEC-Q100 qualification.