Texas Instruments

MAX3232CDRG4 - Dual RS-232 Transceiver | Texas Instruments

MPN: MAX3232CDRG4 ✓ Nakahanda
3 V to 5.5 V Vdss 16-SOIC Package
MOQ: 1 |

MAX3232CDRG4 Ulas

Texas Instruments MAX3232CDRG4 is a 3 V to 5.5 V dual RS-232 line driver and receiver transceiver with two drivers, two receivers, full-duplex operation, and ±15 kV ESD protection in a 16-pin SOIC package. The device operates at data rates up to 1 Mbit/s and uses four external 0.1 µF charge-pump capacitors. Its 3.3 V-compatible supply range makes it suitable for modern serial interfaces.

An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or embedded processor into RS-232 line levels, while receiving and converting RS-232 signals back into CMOS-compatible logic. In the broader semiconductor hierarchy, this product belongs to the interface IC family, specifically the RS-232 line-driver and receiver category used to bridge modern digital logic with legacy and industrial serial ports.

The principal features of the MAX3232CDRG4 include a 3 V to 5.5 V operating range, two transmit channels, two receive channels, full-duplex operation, and ±15 kV ESD protection. It supports communication rates up to 1 Mbit/s, while its low-power design uses four external 0.1 µF capacitors for the internal charge-pump circuitry. The 16-SOIC package provides a conventional surface-mount form factor for industrial and embedded equipment.

Operationally, the integrated charge pump generates the positive and negative voltage levels required by RS-232 drivers. The receiver section converts incoming differential line voltages into CMOS-compatible outputs, while the transmitter section converts CMOS-compatible inputs into RS-232 levels. This architecture allows a controller with a UART to communicate with a PC, peripheral, instrument, or another RS-232-equipped system without implementing the level-shifting interface externally.

Typical applications include industrial serial consoles, data-acquisition equipment, barcode and identification systems, instrumentation, point-of-sale terminals, and embedded control systems. The 1 Mbit/s capability supports high-speed point-to-point links, while ±15 kV ESD protection improves robustness where cables can be exposed to electrostatic discharge.

When designing the circuit, place all four 0.1 µF charge-pump capacitors close to their associated device pins and follow the manufacturer datasheet layout and polarity markings. Confirm signal levels, ground continuity, and connector exposure in the final system; the ESD rating does not replace appropriate cable and enclosure design.

This product page organizes the operating limits, package information, technical applications, and verified drop-in alternatives for engineers evaluating the MAX3232CDRG4. It also provides practical guidance on capacitor placement, interface robustness, and the distinctions between electrically similar RS-232 transceivers.

Mga alternatibo na pwedeng ilagay na MAX3232CDRG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MAX3232CDRG4 (parehas na form factor at footprint) — pagkakaiba sa Package.

Texas Instruments
Package: 16-TSSOP (0.173 in, 4.40 mm width)
Ikabit sa MAX3232CDRG4 →

MAX3232EIPWG4

✅ Drop-In
Texas Instruments
📦 16-SOIC (narrow)
RS-232 Line Driver/Receiver · 2 · 2 · 3 V to 5.5 V · 250 kbps · +/-15 kV · +/-8 kV · +/-15 kV

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX3232ECDR

✅ Drop-In
Texas Instruments
📦 16-SOIC (narrow)
Dual RS-232 line driver and receiver · 2 channels · 3 V to 5.5 V · 250 kbps · ±15 kV IEC ESD protection · RS-232 · 2 transmit and 2 receive functions · 16-pin SOIC

Magkontak para sa presyo

Tingnan ang Datasheet →

SN65C3232D

✅ Drop-In
📦 16-SOIC (narrow)
The SN65C3232D uses two drivers, two receivers, and ±15 kV ESD protection; differences in charge-pump capacitance, logic thresholds, and timing must be verified before substitution.

📋 Alternatibo na Reference (hindi sa katalogo)

MAX3232CDRG4 Mga Spesipikasyon

Product Type RS-232 line driver/receiver transceiver
Number of Drivers 2
Number of Receivers 2
Duplex Mode Full duplex
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 1 Mbit/s
ESD Protection ±15 kV
External Charge-Pump Capacitors 4 × 0.1 µF
Hanay ng Temperature na Operasyon 0 °C to 70 °C
Technology CMOS
Packhaging 16-SOIC
Package Width 3.90 mm (0.154 in)
Uri ng Pagpapasok Surface mount
Lead-Free Status Lead-free
RS-232 Standard TIA/EIA-232-F
Bilang ng Pin 16

Gabay sa Pin Configuration ng MAX3232CDRG4 3.90 mm (0.154 in)

Pin configuration para sa MAX3232CDRG4 (3.90 mm (0.154 in) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 3.90 mm (0.154 in) package para sa MAX3232CDRG4

Wala ng detalyadong pinout data na magagamit para sa MAX3232CDRG4.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MAX3232CDRG4 ay nararapat para sa 6 aplikasyons: Industrial Serial Console, Data-Acquisition Equipment, Point-of-Sale Terminal, Embedded Test and Measurement, Barcode and Identification System, Embedded Control System.

🏭

Industrial Serial Console

The MAX3232CDRG4 fits an industrial serial console because it converts between CMOS UART signals and RS-232 line levels while operating from 3 V to 5.5 V. Two drivers and two receivers support full-duplex communication, and the 1 Mbit/s capability accommodates faster point-to-point transfers than a conventional low-speed serial link. Its ±15 kV ESD protection improves tolerance of electrostatic discharge on exposed equipment connections. Place the four required 0.1 µF capacitors close to the device, maintain a continuous signal-ground path, and confirm the console connector and cable arrangement during system integration.

📟

Data-Acquisition Equipment

The MAX3232CDRG4 can connect a data-acquisition controller to a host computer through an RS-232 port. The 2/2 channel arrangement provides two transmit and two receive paths for full-duplex communication, while the 3 V to 5.5 V supply range permits operation in mixed 3.3 V and 5 V systems. A maximum rate of 1 Mbit/s can shorten transfer time for sampled records. The ±15 kV ESD rating is useful when the cable connects external laboratory equipment, although the enclosure, connector, and grounding system must also provide appropriate protection.

🏬

Point-of-Sale Terminal

The MAX3232CDRG4 suits a point-of-sale terminal that must communicate with legacy peripherals through RS-232. The full-duplex 2/2 configuration supports simultaneous command and response traffic, and the 3 V to 5.5 V operating range gives designers flexibility when the terminal uses a 3.3 V processor and 5 V peripheral interfaces. Its 1 Mbit/s capability supports a high-speed serial link, while ±15 kV ESD protection adds robustness at a connector exposed to user contact. Place the charge-pump capacitors at the pins specified in the datasheet and validate signal-ground continuity across the complete peripheral cable.

🖥️

Embedded Test and Measurement

The MAX3232CDRG4 is useful in embedded test and measurement equipment that exchanges commands and captured data with a PC or service laptop. Its dual-driver, dual-receiver configuration provides full-duplex control and data channels, while operation from 3 V to 5.5 V supports both legacy instrument interfaces and newer embedded platforms. The device's 1 Mbit/s limit is suitable for rapid instrument-response traffic, and the ±15 kV ESD rating helps protect the interface when service leads connect to external equipment. Designers should preserve the datasheet capacitor layout and evaluate the full cable and ground path.

📷

Barcode and Identification System

The MAX3232CDRG4 can provide the electrical interface between an identification controller and a conventional RS-232 scanner or printer. The two receive channels can accept status information from more than one RS-232 peripheral, while the transmit channels support command and data output. Its 3 V to 5.5 V supply range allows use with both 3.3 V embedded controllers and 5 V peripherals, and the 1 Mbit/s capability is more than adequate for typical identification traffic. The ±15 kV ESD protection is valuable at accessible equipment ports, but suitable strain relief, grounding, and cable routing remain essential.

🔧

Embedded Control System

The MAX3232CDRG4 bridges an embedded controller's UART and an RS-232 service or supervisory interface. Two full-duplex channels allow command, response, status, and diagnostic traffic without requiring external level-shifting components. Its 3 V to 5.5 V operating range supports common embedded supply levels, while 1 Mbit/s operation provides ample bandwidth for control traffic and firmware-service exchanges. The integrated ±15 kV ESD protection strengthens the interface against static discharge at an external connector. Follow the manufacturer layout for the four 0.1 µF charge-pump capacitors and ensure that chassis or signal grounding is designed for the deployment environment.

What is the MAX3232CDRG4?
The MAX3232CDRG4 is a Texas Instruments dual RS-232 transceiver containing two line drivers, two line receivers, and integrated charge-pump circuitry. According to the manufacturer datasheet, it operates from 3 V to 5.5 V, supports full-duplex RS-232 communication up to 1 Mbit/s, provides ±15 kV ESD protection, and is packaged in a 16-SOIC.
What is the operating voltage of the MAX3232CDRG4?
The MAX3232CDRG4 operates from 3 V to 5.5 V. This range supports both conventional 5 V systems and 3.3 V systems. According to the manufacturer datasheet, the device uses four external 0.1 µF capacitors to support its charge-pump function, so the complete circuit should include all four capacitors at the specified locations.
How many RS-232 channels does the MAX3232CDRG4 provide?
The MAX3232CDRG4 provides two transmit channels and two receive channels in a full-duplex configuration. This means the device can support two independent data paths when its driver and receiver sections are paired appropriately. The manufacturer datasheet identifies the part as a 2/2 full-duplex RS-232 transceiver.
What is the maximum data rate of the MAX3232CDRG4?
The MAX3232CDRG4 supports data rates up to 1 Mbit/s. According to the manufacturer datasheet, this is a low-power true RS-232 transceiver using four external 0.1 µF capacitors. The maximum rate applies to suitable signal integrity, cable, load, and layout conditions; verify the complete interface configuration before relying on operation at the upper limit.
Where can I download the MAX3232CDRG4 datasheet PDF?
The MAX3232CDRG4 datasheet is available through the datasheet page linked on this product page. It documents the 3 V to 5.5 V supply range, 2/2 transceiver configuration, ±15 kV ESD protection, external-capacitor requirements, and package information. Use the manufacturer datasheet as the controlling document for pin assignments, capacitor polarity, electrical limits, and recommended layout.
Where can I find the MAX3232CDRG4 pinout?
Use the pin-description table and package drawing in the MAX3232CDRG4 manufacturer datasheet to locate every connection on the 16-SOIC package. The public search information confirms the 16-SOIC package but does not provide a complete pin-number table for this product page. Follow the datasheet for driver inputs, receiver outputs, charge-pump capacitors, and supply connections.
What capacitors does the MAX3232CDRG4 require?
The MAX3232CDRG4 requires four external 0.1 µF charge-pump capacitors. According to the manufacturer datasheet, these capacitors support the internal charge-pump circuitry that generates the voltage levels required by the RS-232 drivers. Place each capacitor close to its designated IC pins and observe the polarity and connection details shown in the datasheet layout.
Is the MAX3232CDRG4 a 3.3 V RS-232 interface?
Yes, the MAX3232CDRG4 can operate from a 3.3 V supply because its rated input range is 3 V to 5.5 V. It retains the bipolar line-level signaling required by RS-232 through its integrated charge pump. The manufacturer datasheet identifies a maximum signaling rate of 1 Mbit/s and ±15 kV ESD protection.
What can replace the MAX3232CDRG4?
The MAX3232E is identified by Texas Instruments as an improved direct drop-in replacement for the MAX3232, while the SN65C3232D is described as a two-channel RS-232 device with driver, receiver, and ±15 kV ESD functions. Verify the exact orderable suffix, package dimensions, temperature grade, and pin mapping against the manufacturer datasheet before production use.
Is the SN65C3232D pin-compatible with the MAX3232CDRG4?
The SN65C3232D is a two-channel RS-232 transceiver whose driver and receiver functions align with the MAX3232CDRG4 application, and comparative product information identifies a pin-to-pin relationship. According to the manufacturer and comparison descriptions, it includes dual drivers, dual receivers, and ±15 kV ESD protection. Confirm package width, pin numbering, and charge-pump connections before substitution.
MAX3232CDRG4 vs MAX3232E: which is better for a new design?
The MAX3232E is generally the better choice for a new design because Texas Instruments identifies it as an improved direct drop-in replacement for the MAX3232. The MAX3232CDRG4 remains appropriate for maintaining an existing 16-SOIC design. Compare the complete datasheet specifications, especially supply limits, timing, ESD behavior, and package details, before changing the BOM.
When should I choose the MAX3232CDRG4 instead of the MAX3232E?
Choose the MAX3232CDRG4 when maintaining an existing design specifically configured for the MAX3232CD family and when its manufacturer datasheet confirms that the required operating conditions are met. Choose the MAX3232E for new designs when its improved characteristics are preferred. Both are relevant to the same RS-232 interface category, but final equivalence must be established at the exact orderable-part level.
Is the MAX3232CDRG4 suitable for industrial serial communication?
The MAX3232CDRG4 is suitable for industrial serial interfaces when the system remains within its 0 °C to 70 °C operating range. It provides two drivers, two receivers, full-duplex operation, 1 Mbit/s operation, and ±15 kV ESD protection. For wider-temperature equipment, select a grade whose specified temperature range covers the enclosure environment.
Where can I buy MAX3232CDRG4 and request current lead time?
Use the Request a Quote form on this page to request MAX3232CDRG4 availability, current lead time, and order quantities. The available product listings confirm that the part is offered as a 16-SOIC RS-232 transceiver, but the verified listings do not contain a complete quantity-break price table or a factory lead-time statement. The quote form is the appropriate channel for current commercial terms.
What are the key specifications of MAX3232CDRG4 that engineers should know?
The MAX3232CDRG4 combines two drivers, two receivers, a 3 V to 5.5 V supply range, full-duplex RS-232 operation, data rates up to 1 Mbit/s, and ±15 kV ESD protection in a 16-SOIC package. According to the manufacturer datasheet, four external 0.1 µF capacitors are required. Its commercial-grade operating-temperature range is 0 °C to 70 °C.
Does the MAX3232CDRG4 provide ±15 kV ESD protection?
Yes, the MAX3232CDRG4 provides ±15 kV ESD protection. The rating is identified in the product description and comparative manufacturer material for the MAX3232CD family. The protection rating does not eliminate the need for sound grounding, controlled cable routing, suitable connectors, and an enclosure designed for the operating environment.

Impormasyon ng Talumpati sa Engineering for MAX3232CDRG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the MAX3232CDRG4 when maintaining an existing MAX3232CD-based RS-232 design, particularly with a 3 V to 5.5 V supply, two transmit channels, two receive channels, and a 1 Mbit/s interface requirement. Its 16-SOIC format also fits conventional narrow SOIC layouts, while four external 0.1 µF capacitors are required. Choose the MAX3232E for a new design when Texas Instruments' improved direct-replacement family is preferred and its exact specifications satisfy the application. MAX3232ECDR is a relevant same-family alternative for designs using the narrow CD package, but verify the full orderable suffix and electrical limits. Consider the SN65C3232D when its two-channel RS-232 architecture and ESD capability meet the interface requirements, after checking package dimensions, logic thresholds, timing, and charge-pump capacitor requirements. For any substitution, compare the complete manufacturer datasheets rather than relying only on the RS-232 connector pinout.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MAX3232E MAX3232ECDR SN65C3232D
Package 16-SOIC (narrow) 16-SOIC (narrow) 16-SOIC (narrow) 16-SOIC (narrow)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Transmitter Channels 2 2 2 2
Receiver Channels 2 2 2 2
Drop-In Status Reference device Texas Instruments identifies it as an improved direct drop-in replacement for MAX3232 MAX3232E-family 16-SOIC candidate; exact suffix must be checked Two-channel pin-compatibility candidate; verify package and capacitor requirements

Pangunahing mga Pagkakaiba

  • Commercial 3 V to 5.5 V operation with full-duplex RS-232 (kumpara saMAX3232E)
  • Two-channel interface with defined high-level ESD protection (kumpara saSN65C3232D)
  • Existing MAX3232CD family design continuity (kumpara saMAX3232ECDR)

Talaan ng Disenyo

Place the four required 0.1 µF charge-pump capacitors immediately adjacent to their designated MAX3232CDRG4 pins, following the manufacturer datasheet layout and polarity. Keep the charge-pump loop compact to limit switching noise and high-current trace area. Route the connector-side and logic-side ground through a common solid plane, and avoid placing sensitive analog traces between the charge-pump nodes and the RS-232 interface.

Use a continuous ground reference between the transceiver, UART, and remote RS-232 equipment. A common cause of unreliable RS-232 communication is a floating or interrupted signal-ground path rather than a failure of the line driver. Confirm the UART logic levels, driver input states, receiver output levels, and cable pinout using the manufacturer pin-description table before production release.

Do not treat the ±15 kV ESD rating as a substitute for external surge protection, isolation, or a compliant enclosure. The rating describes the device's ESD capability under its specified test conditions. Use suitable connector retention, cable strain relief, grounding, and system-level electrostatic-discharge controls, especially when the RS-232 connector is accessible to operators or connected to long external cables.

Separate the exposed RS-232 connector and cable routing from sensitive logic and clock traces. Keep the interface return path short, terminate unused inputs according to the datasheet, and inspect the assembled PCB for accidental open ground connections. When substituting another transceiver, verify package width, pin numbering, charge-pump capacitor values, shutdown behavior, and temperature grade rather than relying only on the connector arrangement.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Yes
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The verified product information identifies the MAX3232CDRG4 as lead-free. RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status require confirmation from the applicable manufacturer declaration or product documentation.

Data napatotohanan sa: 2026-11-09 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MAX3232CDRG4 datasheet MAX3232CDRG4 pinout MAX3232CDRG4 datasheet pdf MAX3232CDRG4 schematic MAX3232CDRG4 equivalent MAX3232CDRG4 replacement MAX3232CDRG4 cross reference MAX3232CDRG4 vs MAX3232E MAX3232CDRG4 footprint MAX3232CDRG4 spice model MAX3232CDRG4 price MAX3232CDRG4 stock Texas Instruments MAX3232CDRG4 MAX3232 16-SOIC RS-232 transceiver MAX3232 industrial serial communication

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments MAX3232CDRG4 MAX3232E MAX3232ECDR SN65C3232D RS-232 transceiver RS-232 line driver RS-232 line receiver interface IC CMOS logic full duplex charge-pump capacitors ESD protection 1 Mbit/s 3 V to 5.5 V supply 16-SOIC SOIC package family surface mount TIA/EIA-232-F industrial serial communication lead-free RoHS REACH AEC-Q100
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ