MAX3232CDRG4 - Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232CDRG4 ✓ Hoạt độngMAX3232CDRG4 Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or embedded processor into RS-232 line levels, while receiving and converting RS-232 signals back into CMOS-compatible logic. In the broader semiconductor hierarchy, this product belongs to the interface IC family, specifically the RS-232 line-driver and receiver category used to bridge modern digital logic with legacy and industrial serial ports.
The principal features of the MAX3232CDRG4 include a 3 V to 5.5 V operating range, two transmit channels, two receive channels, full-duplex operation, and ±15 kV ESD protection. It supports communication rates up to 1 Mbit/s, while its low-power design uses four external 0.1 µF capacitors for the internal charge-pump circuitry. The 16-SOIC package provides a conventional surface-mount form factor for industrial and embedded equipment.
Operationally, the integrated charge pump generates the positive and negative voltage levels required by RS-232 drivers. The receiver section converts incoming differential line voltages into CMOS-compatible outputs, while the transmitter section converts CMOS-compatible inputs into RS-232 levels. This architecture allows a controller with a UART to communicate with a PC, peripheral, instrument, or another RS-232-equipped system without implementing the level-shifting interface externally.
Typical applications include industrial serial consoles, data-acquisition equipment, barcode and identification systems, instrumentation, point-of-sale terminals, and embedded control systems. The 1 Mbit/s capability supports high-speed point-to-point links, while ±15 kV ESD protection improves robustness where cables can be exposed to electrostatic discharge.
When designing the circuit, place all four 0.1 µF charge-pump capacitors close to their associated device pins and follow the manufacturer datasheet layout and polarity markings. Confirm signal levels, ground continuity, and connector exposure in the final system; the ESD rating does not replace appropriate cable and enclosure design.
This product page organizes the operating limits, package information, technical applications, and verified drop-in alternatives for engineers evaluating the MAX3232CDRG4. It also provides practical guidance on capacitor placement, interface robustness, and the distinctions between electrically similar RS-232 transceivers.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CDRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CDRG4 (cùng hình factor và footprint) — khác nhau ở Package.
MAX3232EIPWG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ECDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN65C3232D
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232CDRG4 Thông số kỹ thuật
| Product Type | RS-232 line driver/receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 1 Mbit/s |
| ESD Protection | ±15 kV |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| Khoảng nhiệt độ hoạt động | 0 °C to 70 °C |
| Technology | CMOS |
| Hộp | 16-SOIC |
| Package Width | 3.90 mm (0.154 in) |
| Kiểu lắp đặt | Surface mount |
| Lead-Free Status | Lead-free |
| RS-232 Standard | TIA/EIA-232-F |
| Số chân | 16 |
Hướng dẫn cấu hình chân MAX3232CDRG4 3.90 mm (0.154 in)
Cấu hình chân cho MAX3232CDRG4 (3.90 mm (0.154 in) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232CDRG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232CDRG4 phù hợp cho 6 Áp dụngs: Industrial Serial Console, Data-Acquisition Equipment, Point-of-Sale Terminal, Embedded Test and Measurement, Barcode and Identification System, Embedded Control System.
Industrial Serial Console
The MAX3232CDRG4 fits an industrial serial console because it converts between CMOS UART signals and RS-232 line levels while operating from 3 V to 5.5 V. Two drivers and two receivers support full-duplex communication, and the 1 Mbit/s capability accommodates faster point-to-point transfers than a conventional low-speed serial link. Its ±15 kV ESD protection improves tolerance of electrostatic discharge on exposed equipment connections. Place the four required 0.1 µF capacitors close to the device, maintain a continuous signal-ground path, and confirm the console connector and cable arrangement during system integration.
Được đề xuất
Data-Acquisition Equipment
The MAX3232CDRG4 can connect a data-acquisition controller to a host computer through an RS-232 port. The 2/2 channel arrangement provides two transmit and two receive paths for full-duplex communication, while the 3 V to 5.5 V supply range permits operation in mixed 3.3 V and 5 V systems. A maximum rate of 1 Mbit/s can shorten transfer time for sampled records. The ±15 kV ESD rating is useful when the cable connects external laboratory equipment, although the enclosure, connector, and grounding system must also provide appropriate protection.
Được đề xuất
Point-of-Sale Terminal
The MAX3232CDRG4 suits a point-of-sale terminal that must communicate with legacy peripherals through RS-232. The full-duplex 2/2 configuration supports simultaneous command and response traffic, and the 3 V to 5.5 V operating range gives designers flexibility when the terminal uses a 3.3 V processor and 5 V peripheral interfaces. Its 1 Mbit/s capability supports a high-speed serial link, while ±15 kV ESD protection adds robustness at a connector exposed to user contact. Place the charge-pump capacitors at the pins specified in the datasheet and validate signal-ground continuity across the complete peripheral cable.
Được đề xuất
Embedded Test and Measurement
The MAX3232CDRG4 is useful in embedded test and measurement equipment that exchanges commands and captured data with a PC or service laptop. Its dual-driver, dual-receiver configuration provides full-duplex control and data channels, while operation from 3 V to 5.5 V supports both legacy instrument interfaces and newer embedded platforms. The device's 1 Mbit/s limit is suitable for rapid instrument-response traffic, and the ±15 kV ESD rating helps protect the interface when service leads connect to external equipment. Designers should preserve the datasheet capacitor layout and evaluate the full cable and ground path.
Được đề xuất
Barcode and Identification System
The MAX3232CDRG4 can provide the electrical interface between an identification controller and a conventional RS-232 scanner or printer. The two receive channels can accept status information from more than one RS-232 peripheral, while the transmit channels support command and data output. Its 3 V to 5.5 V supply range allows use with both 3.3 V embedded controllers and 5 V peripherals, and the 1 Mbit/s capability is more than adequate for typical identification traffic. The ±15 kV ESD protection is valuable at accessible equipment ports, but suitable strain relief, grounding, and cable routing remain essential.
Được đề xuất
Embedded Control System
The MAX3232CDRG4 bridges an embedded controller's UART and an RS-232 service or supervisory interface. Two full-duplex channels allow command, response, status, and diagnostic traffic without requiring external level-shifting components. Its 3 V to 5.5 V operating range supports common embedded supply levels, while 1 Mbit/s operation provides ample bandwidth for control traffic and firmware-service exchanges. The integrated ±15 kV ESD protection strengthens the interface against static discharge at an external connector. Follow the manufacturer layout for the four 0.1 µF charge-pump capacitors and ensure that chassis or signal grounding is designed for the deployment environment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CDRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232E | MAX3232ECDR | SN65C3232D |
|---|---|---|---|---|
| Package | 16-SOIC (narrow) | 16-SOIC (narrow) | 16-SOIC (narrow) | 16-SOIC (narrow) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transmitter Channels | 2 | 2 | 2 | 2 |
| Receiver Channels | 2 | 2 | 2 | 2 |
| Drop-In Status | Reference device | Texas Instruments identifies it as an improved direct drop-in replacement for MAX3232 | MAX3232E-family 16-SOIC candidate; exact suffix must be checked | Two-channel pin-compatibility candidate; verify package and capacitor requirements |
Bảo phân biệt quan trọng
- Commercial 3 V to 5.5 V operation with full-duplex RS-232 (vsMAX3232E)
- Two-channel interface with defined high-level ESD protection (vsSN65C3232D)
- Existing MAX3232CD family design continuity (vsMAX3232ECDR)
Ghi chú thiết kế
Place the four required 0.1 µF charge-pump capacitors immediately adjacent to their designated MAX3232CDRG4 pins, following the manufacturer datasheet layout and polarity. Keep the charge-pump loop compact to limit switching noise and high-current trace area. Route the connector-side and logic-side ground through a common solid plane, and avoid placing sensitive analog traces between the charge-pump nodes and the RS-232 interface.
Use a continuous ground reference between the transceiver, UART, and remote RS-232 equipment. A common cause of unreliable RS-232 communication is a floating or interrupted signal-ground path rather than a failure of the line driver. Confirm the UART logic levels, driver input states, receiver output levels, and cable pinout using the manufacturer pin-description table before production release.
Do not treat the ±15 kV ESD rating as a substitute for external surge protection, isolation, or a compliant enclosure. The rating describes the device's ESD capability under its specified test conditions. Use suitable connector retention, cable strain relief, grounding, and system-level electrostatic-discharge controls, especially when the RS-232 connector is accessible to operators or connected to long external cables.
Separate the exposed RS-232 connector and cable routing from sensitive logic and clock traces. Keep the interface return path short, terminate unused inputs according to the datasheet, and inspect the assembled PCB for accidental open ground connections. When substituting another transceiver, verify package width, pin numbering, charge-pump capacitor values, shutdown behavior, and temperature grade rather than relying only on the connector arrangement.
Thông tin tuân thủ
The verified product information identifies the MAX3232CDRG4 as lead-free. RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status require confirmation from the applicable manufacturer declaration or product documentation.