MAX499CWG - 3-Channel 250MHz Video Switch | Maxim
MPN: MAX499CWG ✓ NakahandaMAX499CWG Ulas
A video switch is an analog signal-routing component that connects one source to a selected destination while preserving signal amplitude and timing. The MAX499CWG belongs to the analog switch and video buffer amplifier category, combining SPDT routing with active output stages. This integration reduces the number of external buffer components required when several RGB video paths must be switched.
The principal performance characteristics include 250 MHz small-signal bandwidth, 135 MHz full-power bandwidth, 0.1 dB gain flatness, a 1250 V/µs slew rate, and 0.03° differential or 0.06% differential settling characteristics. These figures make the device suitable for video paths in which higher-bandwidth content, including standard-definition and higher-resolution consumer video signals, must pass through the switching stage.
The MAX499 offers three independently controlled switching channels. Each channel combines an SPDT switch with a video buffer amplifier, allowing an incoming signal to be routed between two possible output paths while maintaining a low-impedance drive capability. The MAX499 dissipation is 300 mW with all output buffers enabled and 100 mW with all buffers disabled when operated from ±5 V supplies, according to the manufacturer datasheet.
Typical uses include RGB video routing in broadcast and presentation equipment, video test and measurement systems, computer-video interfaces, video switchers, and multimedia consoles. The integrated buffers are particularly useful when the selected destination would otherwise require a separate video amplifier to drive downstream cabling or another video stage.
PCB design should account for the 24-pin SOIC footprint, clean supply connections, and the high slew rate of the output amplifiers. Keep video traces short, provide solid ground-plane continuity, and place decoupling capacitors close to the supply pins. Because the amplifiers can operate from dual supplies, unused supply rails and unused channels should be handled according to the manufacturer application guidance to avoid unnecessary current or signal-path issues.
This product page combines the manufacturer performance data with practical routing, layout, and selection guidance. It also distinguishes the MAX499CWG from four-channel MAX498 variants and documents where engineering verification is still required before substituting a different package, temperature grade, or function-compatible switch.
Mga alternatibo na pwedeng ilagay na MAX499CWG — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboMAX499CWG Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Channels | 3 channels |
| Switch Configuration | SPDT |
| Signal Type | RGB analog video |
| Small-Signal -3 dB Bandwidth | 250 MHz |
| Full-Power -3 dB Bandwidth | 135 MHz |
| Gain Flatness | 0.1 dB |
| Slew Rate | 1250 V/µs to 0.1% settling time |
| Differential Settling Error | 0.03° or 0.06% |
| Enabled Power Dissipation | 300 mW typical at ±5 V |
| Disabled Power Dissipation | 100 mW typical at ±5 V |
| Packhaging | 24-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Temperature Grade | Commercial |
| Number of Terminals | 24 terminals |
Gabay sa Pin Configuration ng MAX499CWG 24-pin soic
Pin configuration para sa MAX499CWG (24-pin soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MAX499CWG.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MAX499CWG ay nararapat para sa 6 aplikasyons: Broadcast RGB Video Routing, Video Test and Measurement, Professional Video Mixers, Computer and Multimedia Video Switching, Video Presentation Equipment, Analog Video Matrix and Patch Systems.
Broadcast RGB Video Routing
The MAX499CWG is suitable for broadcast-style RGB routing because it combines three SPDT switches with active video buffers in one 24-pin SOIC device. Its 250 MHz small-signal bandwidth and 135 MHz full-power bandwidth support fast analog transitions while the 0.1 dB gain-flatness specification helps limit amplitude variation across the usable frequency range. A broadcaster can route a source between two destinations or isolate inputs during test operations. The 1250 V/µs slew rate improves edge reproduction, but short traces, a continuous ground plane, and local supply bypassing remain essential for controlling reflection and crosstalk in rack-level video equipment.
Inirekomenda
Video Test and Measurement
The MAX499CWG can serve as the routing element in a video test system that connects RGB signals to an analyzer, reference source, or display. Its 135 MHz full-power bandwidth and 250 MHz small-signal bandwidth provide useful headroom for high-bandwidth video signals, while the integrated buffer reduces the need for separate amplifiers immediately after the switch. The 0.03° or 0.06% differential settling characteristics are relevant when timing or transient behavior is measured. For repeatable results, keep input and output paths short, use a low-impedance ground reference, and decouple the dual supply rails close to the device.
Inirekomenda
Professional Video Mixers
MAX499CWG fits professional video mixers and production switchers that need to route multiple RGB signals between processing stages. Three channels provide a practical match for systems handling red, green, and blue paths independently, and the integrated buffers can drive the next stage more effectively than an unbuffered passive switch. The MAX499’s 1250 V/µs slew rate preserves rapid transitions, while its 0.1 dB gain-flatness characteristic supports consistent video amplitude. Designers should preserve ground-plane continuity, avoid long routes around connector or processor sections, and check channel enable sequencing in the complete switching system.
Inirekomenda
Computer and Multimedia Video Switching
The MAX499CWG is applicable to computer-video and multimedia switching equipment that selects among multiple RGB sources. Its three independent SPDT channels permit source selection without adding a separate amplifier after each routing point, and the 250 MHz small-signal bandwidth covers a broad range of analog video content. The commercial 24-pin SOIC package supports surface-mount assembly but requires careful handling of high-speed edges around connectors and processor interfaces. Use short video traces, maintain a common ground plane, and place bypass capacitors near the supply pins to minimize noise coupling into downstream display circuitry.
Inirekomenda
Video Presentation Equipment
MAX499CWG can route RGB signals in presentation systems that combine computers, playback devices, and projection equipment. The integrated video buffers help isolate selected outputs and provide a more suitable drive level for downstream cables and receivers. A 135 MHz full-power bandwidth and 0.1 dB gain flatness support consistent signal transfer, while the 1250 V/µs slew rate accommodates fast transitions. Because presentation equipment may contain switching regulators and long cable runs, designers should use a continuous ground plane, keep the MAX499 output routes compact, and validate the completed system for crosstalk, ringing, and ground-offset errors.
Inirekomenda
Analog Video Matrix and Patch Systems
The MAX499CWG can be used in compact analog video matrices or patch systems that route three RGB-related paths between source and destination modules. SPDT switching gives each channel two selectable routes, while the integrated buffer improves drive capability into the next stage. The MAX499 consumes less enabled dissipation than the four-channel MAX498, which is 300 mW versus 390 mW under ±5 V operation, making it potentially preferable when only three channels are needed. System planners should still evaluate channel count, source impedance, cable loading, and thermal performance across the complete matrix rather than treating the IC as an unrestricted cable driver.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MAX499CWG — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Maxim Integrated |
| Package | 24-pin SOIC |
| Number of Channels | 3 |
| Switch Configuration | SPDT |
| Small-Signal -3 dB Bandwidth | 250 MHz |
| Full-Power -3 dB Bandwidth | 135 MHz |
| Gain Flatness | 0.1 dB |
| Slew Rate | 1250 V/µs to 0.1% settling time |
| Enabled Power Dissipation | 300 mW typical at ±5 V |
| Disabled Power Dissipation | 100 mW typical at ±5 V |
| Signal Type | RGB analog video |
Pangunahing mga Pagkakaiba
- Three integrated SPDT channels with video buffers (kumpara saMAX498)
- High small-signal bandwidth in a compact SOIC (kumpara saMAX498)
- Separate control of integrated output buffers (kumpara saUnbuffered SPDT switch alternatives)
Talaan ng Disenyo
Place the MAX499CWG near the video connectors or signal-processing stages that create the longest routing paths. Keep RGB traces short and continuous, remove unnecessary test-point stubs, and use a solid ground plane beneath and around the device. The 1250 V/µs slew rate can expose trace discontinuities, connector transitions, and impedance changes as ringing, so the complete signal path should be reviewed with the intended cable and connector loads.
Connect the dual supply rails with low-impedance traces and place the required decoupling capacitors close to the corresponding device pins. The manufacturer datasheet specifies typical dissipation of 300 mW with all three output buffers enabled and 100 mW with all buffers disabled under ±5 V operation. Estimate the worst-case board-level dissipation from actual channel state and ambient temperature, then verify that the PCB copper and surrounding airflow keep the device within its specified operating conditions.
Check source impedance, destination loading, cable length, and output-buffer enable state as one signal-chain design rather than tuning them independently. The 250 MHz small-signal and 135 MHz full-power bandwidth figures describe device performance under specified conditions, not guaranteed bandwidth for every external load. Use controlled-impedance routing where appropriate and inspect the assembled video path with an oscilloscope for overshoot, ringing, crosstalk, and settling.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer documentation used for this product does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements for the exact ordering code. Request current compliance documentation for MAX499CWG through the Request a Quote form when a formal declaration is required.