Microchip Technology

MCP3302T-CI/ST - 13-Bit 4-Input SPI ADC | Microchip

MPN: MCP3302T-CI/ST ✓ Nakahanda
2.7 V to 5.5 V Vdss 14-pin TSSOP Package
MOQ: 1 |

MCP3302T-CI/ST Ulas

Microchip Technology MCP3302T-CI/ST is a 13-bit successive-approximation analog-to-digital converter with four single-ended or two differential inputs, conversion rates up to 100 ksps, and an SPI serial interface in a 14-pin TSSOP package. Its tested 2.7 V to 5.5 V operating supply range supports both 3.3 V and 5 V systems.

An ADC is a data-conversion IC that transforms an analog voltage into a digital value for measurement, control, or signal processing. The MCP3302 belongs to the SAR ADC family, where a successive-approximation internal DAC compares the sampled input with successive trial voltages. Its differential-input architecture can reject common-mode noise, while single-ended operation simplifies connections for sensors, potentiometers, and resistive dividers.

Key features include 13-bit resolution, four analog inputs, two differential channels, a 100 ksps maximum conversion rate, and an SPI-compatible serial interface. According to the manufacturer datasheet, the reference voltage can range from 400 mV to 5 V. This produces input-referred resolutions between 98 µV and 1.22 mV, depending on the selected reference voltage and gain configuration.

The converter uses an internal sample-and-hold architecture and a successive-approximation conversion sequence. Differential channel selection is controlled through the serial interface, allowing two analog pairs to share one converter while maintaining consistent sampling and conversion timing. The SPI interface provides a straightforward connection to microcontrollers, although software must handle chip selection, clocking, and conversion-start timing.

Typical uses include industrial process measurement, battery-powered sensor nodes, remote data acquisition, temperature sensing with thermistors or RTDs, potentiometer position measurement, and low-voltage analog monitoring. Differential inputs are particularly useful when the measured signal is small relative to system noise or when a sensor has a ground-referenced output that cannot be connected directly to a single-ended input.

For reliable operation, keep the analog and digital return paths controlled, bypass the supply close to the device, and select a quiet reference source. Input voltage must remain within the ADC input range, and the common-mode limits of the differential inputs must be checked against the chosen reference and supply voltages before layout is finalized.

This page combines converter specifications, package and interface guidance, practical application notes, and compatible replacement analysis. It is designed to help engineers determine whether the MCP3302T-CI/ST fits a precision measurement design and how to integrate it without overlooking reference, input-range, or SPI-timing constraints.

Mga alternatibo na pwedeng ilagay na MCP3302T-CI/ST — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MCP3302T-CI/ST (parehas na form factor at footprint) — pagkakaiba sa Input Configuration, Serial Interface.

Microchip Technology
Input Configuration: 2 fully differential input channels
Serial Interface: SPI

MCP3302-CI/ST

✅ Drop-In
Microchip Technology
📦 14-TSSOP
Successive approximation ADC · 13 bit · 2 channels · 2 fully differential input channels · 100 ksps · SPI · 14-pin TSSOP · Tube

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3302T-BI/ST

✅ Drop-In
Microchip Technology
📦 14-TSSOP
13 bit · 2 channels · 2 or 4 inputs · Successive-approximation register (SAR) · Single-ended and differential inputs · SPI · 14-TSSOP · 14 pins

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3302T-I/ST

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 14-TSSOP
Same family, 13-bit resolution, two differential channels, and 14-TSSOP footprint; grade and ordering-code differences require datasheet verification

📋 Alternatibo na Reference (hindi sa katalogo)

MCP3302T-BI/ST

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 14-TSSOP
13 bit · 2 channels · 2 or 4 inputs · Successive-approximation register (SAR) · Single-ended and differential inputs · SPI · 14-TSSOP · 14 pins

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3302-CI/ST

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 14-TSSOP
Successive approximation ADC · 13 bit · 2 channels · 2 fully differential input channels · 100 ksps · SPI · 14-pin TSSOP · Tube

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3302T-CI/ST Mga Pinakamataas na Rating at Electrical Characteristics

Pangangasiwaan 13 bit
Input Configuration 4 single-ended or 2 differential inputs
Conversion Architecture Successive-approximation SAR ADC
Maximum Conversion Rate 100 ksps
Tested Supply Voltage Range 2.7 V to 5.5 V
Reference Voltage Range 400 mV to 5 V
Minimum Input-Referred Resolution 98 µV
Maximum Input-Referred Resolution 1.22 mV
Serial Interface SPI-compatible serial interface
Packhaging 14-pin TSSOP
Uri ng Pagpapasok Surface mount
Analog Input Type Differential and single-ended
Tindminan RoHS unknown
REACH Status unknown

Gabay sa Pin Configuration ng MCP3302T-CI/ST 14-pin tssop

Pin configuration para sa MCP3302T-CI/ST (14-pin tssop package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 14-pin tssop package para sa MCP3302T-CI/ST

Wala ng detalyadong pinout data na magagamit para sa MCP3302T-CI/ST.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MCP3302T-CI/ST ay nararapat para sa 6 aplikasyons: Industrial Process Measurement, Battery-Powered Sensor Node, Temperature Sensing, Potentiometer Position Measurement, Remote Data Acquisition, Precision Analog Monitoring.

🏭

Industrial Process Measurement

The MCP3302T-CI/ST is appropriate for acquiring low-level industrial process signals with two differential channels or four single-ended inputs. Its differential inputs help reject common-mode voltage present on sensor wiring, while the 13-bit resolution and adjustable reference voltage support measurements in the millivolt-to-volt range. The converter reaches up to 100 ksps, allowing periodic process monitoring without excessive conversion latency. Place the sensor return and analog ground in a controlled layout, provide a low-noise reference, and ensure every input remains within the selected common-mode range. The SPI interface also allows the converter to share a bus with industrial control circuitry when chip-select and timing are managed correctly.

🧩

Battery-Powered Sensor Node

The MCP3302T-CI/ST fits remote and battery-powered sensor nodes because it combines a 2.7 V minimum operating supply with low-power operation and an SPI-compatible interface. Four single-ended inputs can monitor temperature, pressure, or resistive sensor elements, while two differential channels can improve immunity to ground offsets in longer cables. Conversion rates up to 100 ksps provide flexibility for both slow environmental measurements and faster event-based sampling. Energy use should be evaluated over the complete duty cycle, including reference behavior, digital activity, and sleep intervals. Keep the analog front end close to the converter and use a stable, low-power reference to preserve repeatability and extend operating time.

🌡️

Temperature Sensing

The MCP3302T-CI/ST can digitize thermistor, RTD, or temperature-sensor signals through either single-ended or differential inputs. Differential excitation can cancel the effects of common-mode voltage and shared wiring errors, while the 13-bit output resolution supports accurate temperature interpolation over a carefully selected sensing range. The reference voltage directly influences resolution, so it should be chosen to match the sensor output while preserving sufficient headroom. Keep sensor traces away from switching nodes and connect the return path according to the sensor’s grounding method. Conversion time is normally much shorter than thermal response time, so the SPI sampling interval should be matched to the desired thermal update rate.

🔧

Potentiometer Position Measurement

The MCP3302T-CI/ST supports accurate potentiometer position readout by measuring the wiper voltage relative to one end of the resistive track. A 13-bit converter provides 8192 digital codes, and the reference range of 400 mV to 5 V allows the analog span to be matched to the potentiometer and excitation voltage. Differential operation can reduce sensitivity to reference drift or common supply disturbance, provided the track and wiper remain within the input limits. Keep the resistive track away from high-current paths to prevent resistive heating and local voltage distortion. The high conversion capability also allows the system to implement filtering or redundant readings for mechanical position systems.

📡

Remote Data Acquisition

The MCP3302T-CI/ST is suitable for compact remote data-acquisition modules that must measure several low-energy sensors and transmit results through a serial controller. Two differential channels improve signal integrity when the acquisition node is connected to grounded or floating sensors over longer wiring runs. The 100 ksps conversion capability provides more throughput than many slowly changing environmental measurements require, while the compact 14-pin TSSOP package conserves board area. Firmware should define the full SPI transaction, sample timing, and input multiplexing sequence before production. A stable reference and careful grounding are particularly important when the converter is located far from the system controller.

🖥️

Precision Analog Monitoring

The MCP3302T-CI/ST can monitor precision analog nodes in laboratory, instrumentation, and embedded-control systems where 13-bit resolution and flexible differential measurement are valuable. Its selectable reference supports multiple signal ranges, from a 400 mV minimum to a 5 V maximum, allowing one converter architecture to serve several measurement classes. The serial interface reduces pin count compared with many parallel-output ADCs, although clock and data-capture timing must be handled accurately. Use short analog traces, a low-impedance reference, and a controlled return network to maximize repeatability. For fast-changing signals, evaluate acquisition time and source settling rather than relying only on the headline conversion rate.

What are the key specifications of MCP3302T-CI/ST that engineers should know?
The MCP3302T-CI/ST is a 13-bit SAR ADC with four single-ended or two differential inputs, a maximum conversion rate of 100 ksps, an SPI-compatible interface, and a 14-pin TSSOP package. According to the manufacturer datasheet, its tested supply range is 2.7 V to 5.5 V, while its reference voltage can range from 400 mV to 5 V. Those reference choices correspond to input-referred resolutions from 98 µV to 1.22 mV.
What is the operating voltage of MCP3302T-CI/ST?
The MCP3302T-CI/ST operates from 2.7 V to 5.5 V, with conversion-rate specifications tested over the 4.5 V to 5.5 V portion of that range. This makes the converter suitable for 3.3 V and 5 V embedded systems. According to the manufacturer datasheet, the selected supply must satisfy the analog and digital input limits as well as the supply voltage itself.
How many analog inputs does MCP3302T-CI/ST have?
The MCP3302T-CI/ST provides four single-ended inputs that can be configured as two differential channels. According to the manufacturer datasheet, this arrangement supports full differential input operation while retaining flexible single-ended measurements. Differential mode is useful for rejecting common-mode voltage, whereas single-ended mode simplifies sensor connections when the source voltage is referenced to ground.
What is the conversion rate of MCP3302T-CI/ST?
The MCP3302T-CI/ST supports conversion rates up to 100 ksps. According to the manufacturer datasheet, the maximum rate is specified with a 4.5 V to 5.5 V supply. Actual throughput depends on the SPI clock, conversion latency, chip-select behavior, and firmware sequence, so a system requiring sustained sampling must verify the complete transaction timing.
What is the difference between MCP3302T-CI/ST and MCP3302-CI/ST?
The MCP3302T-CI/ST and MCP3302-CI/ST both use the Microchip MCP3302 family and are identified in comparison data as 13-bit, 14-pin TSSOP converters with SPI connectivity. The available comparison information does not quantify their electrical or ordering differences, so treat them as closely related rather than automatically interchangeable. Confirm the exact temperature grade, packaging code, and production ordering information before substitution.
When should I choose MCP3302T-CI/ST over another 13-bit ADC?
Choose the MCP3302T-CI/ST when the design needs four single-ended or two differential inputs, a compact 14-pin TSSOP footprint, and an SPI interface at rates up to 100 ksps. It is particularly suitable when differential measurement and low supply voltage matter more than a wider native input range. Confirm the reference voltage, common-mode range, acquisition time, and serial timing against the required sensor bandwidth before finalizing the design.
Is MCP3302T-CI/ST suitable for battery-powered sensor applications?
The MCP3302T-CI/ST is suitable for battery-powered sensor applications because Microchip describes the MCP3302 family as low-power and identifies battery-powered systems and remote data acquisition as suitable uses. The 2.7 V to 5.5 V operating range also supports common energy-harvesting and portable-system rails. Actual battery life still depends on operating current, duty cycle, reference circuitry, and the time spent between conversions.
What is the best drop-in replacement for MCP3302T-CI/ST?
The closest supported replacement is the Microchip MCP3302-CI/ST because comparison data identifies both devices as 13-bit, two-channel SPI ADCs in 14-pin TSSOP packages. The MCP3302T-BI/ST is another same-family TSSOP option, but its ordering and grade details should be checked before production use. Because exact pin and parameter equivalence was not quantified for every suffix, perform a footprint and timing review rather than relying on the family name alone.
Can MCP3302-CI/ST replace MCP3302T-CI/ST without PCB changes?
MCP3302-CI/ST is the most plausible drop-in candidate because it is listed as a 13-bit, two-channel SPI ADC in the same 14-pin TSSOP package. The comparison source does not establish every ordering or temperature-grade detail, so verify the exact manufacturer pinout, electrical limits, and ordering codes. Use the MCP3302T-CI/ST datasheet as the controlling reference for any production substitution.
What can replace MCP3302T-CI/ST?
The available replacements are concentrated within the Microchip MCP3302 family, including MCP3302-CI/ST and MCP3302T-BI/ST. Both are identified as 14-pin TSSOP, 13-bit SPI converter options in comparison data. No cross-manufacturer drop-in candidate is established here, and different ADC families may change pin assignments, reference requirements, acquisition timing, or SPI protocols. Confirm the complete datasheet before replacing the device.
Where can I download the MCP3302T-CI/ST datasheet PDF?
The MCP3302T-CI/ST datasheet PDF is available from the manufacturer-document mirror identified as MCP3302TCIST-datasheet.pdf and through the Microchip MCP3302 product page. The manufacturer document is titled “13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface.” Use the pin-description table and electrical-characteristics sections from that document when assigning PCB signals and verifying operating limits.
Where can I find the MCP3302T-CI/ST pinout?
The MCP3302T-CI/ST pinout is contained in the pin-description table of the manufacturer datasheet for the MCP3302 family. The part is supplied in a 14-pin TSSOP package, but the retrieved product material does not expose the individual signal names in a pin-by-pin table. Use the package drawing and pin-description table together to verify analog inputs, supply pins, grounds, reference connections, and SPI signals before layout.
How should the reference voltage be selected for MCP3302T-CI/ST?
The MCP3302T-CI/ST reference may vary from 400 mV to 5 V according to the manufacturer datasheet. A smaller reference improves input-referred resolution for low-level signals but reduces the usable input span, while a larger reference supports wider measurements with coarser absolute resolution. The published range corresponds to input-referred resolutions from 98 µV to 1.22 mV. The reference must also remain within the permitted input range.
Where can I buy MCP3302T-CI/ST and request a quote?
Use the “Request a Quote” form on this XAIPART page to request MCP3302T-CI/ST availability, current commercial terms, and lead time. The component is listed for sale by major distributors, but inventory and transaction status can change independently of this page. Provide the target quantity, acceptable packaging, and required delivery date when submitting the request to obtain an actionable quotation.
What is the lead time for MCP3302T-CI/ST?
Request the current MCP3302T-CI/ST lead time through the “Request a Quote” form on this page. Lead time can vary with order quantity, package form, production scheduling, and destination, so a general estimate would not represent a reliable commitment. Include the required quantity and delivery date so the commercial response can reflect the actual procurement request.
Is MCP3302T-CI/ST in stock?
The MCP3302T-CI/ST is currently offered for sale by distributors, but stock levels are channel-specific and can change quickly. Use the “Request a Quote” form on this page for a current availability response rather than relying on a historical listing status. Include the required quantity and packaging preference so the quote can identify stock that can actually be allocated to the order.

Impormasyon ng Talumpati sa Engineering for MCP3302T-CI/ST — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MCP3302T-CI/ST for a compact 13-bit measurement design that needs four single-ended or two differential inputs, an SPI interface, operation from 2.7 V to 5.5 V, and conversion rates up to 100 ksps. It is especially suitable for battery-powered sensor nodes and industrial acquisition circuits where differential operation can improve common-mode rejection. MCP3302-CI/ST is the closest listed ordering alternative and may suit a design that does not require the target suffix configuration. MCP3302T-BI/ST is another same-family TSSOP option, but its grade and ordering details must be checked against the controlling datasheet. MCP3302T-I/ST and the other listed same-brand variants are appropriate only after confirming electrical limits, temperature range, and pin timing. No cross-manufacturer drop-in part is established here; converters with different pinouts, references, or acquisition timing require PCB or firmware changes rather than a direct substitution.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MCP3302-CI/ST MCP3302T-BI/ST MCP3302T-I/ST
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP
Resolution 13 bit 13 bit 13 bit 13 bit
Input Configuration 4 single-ended or 2 differential inputs 2-channel differential ADC 2-channel differential ADC 2-channel differential ADC
Conversion Architecture Successive-approximation SAR ADC Successive-approximation Successive-approximation Successive-approximation
Reference Voltage Range 400 mV to 5 V 400 mV to 5 V 400 mV to 5 V 400 mV to 5 V
Serial Interface SPI-compatible SPI SPI SPI
Pin Count 14 pins 14 pins 14 pins 14 pins

Pangunahing mga Pagkakaiba

  • Combines two differential channels with four single-ended inputs (kumpara saMCP3302-CI/ST)
  • Supports references from 400 mV to 5 V (kumpara saMCP3302T-BI/ST)
  • Uses a compact 14-pin TSSOP interface (kumpara saMCP3302T-I/ST)

Talaan ng Disenyo

Route the reference, analog inputs, and their return path away from SPI clock, digital output, and switching-node traces. Keep the reference bypass capacitor at the converter’s supply and reference pins, and provide a low-impedance ground connection. The MCP3302 can resolve down to 98 µV with a 400 mV reference, so small layout-induced errors can become significant even though the nominal converter resolution is 13 bit.

Validate the complete SPI timing rather than only the maximum nominal conversion rate. Include conversion latency, chip-select setup and hold requirements, clock polarity, and the time needed to shift 13 result bits in the firmware. Recheck analog settling at each selected gain because a source with high output impedance or excessive capacitance may require a longer acquisition interval than the conversion sequence itself.

Select the reference voltage from the required measurement span rather than using the highest permitted voltage by default. A 400 mV reference maximizes sensitivity for small signals, while a 5 V reference supports a wider input range with coarser absolute resolution. Check the reference current, converter supply current, bypass capacitance, and source impedance together so the reference remains stable during conversions.

Do not assume that a family member with the same TSSOP footprint is automatically interchangeable. Verify the exact pin functions, temperature grade, ordering code, electrical limits, and SPI timing from the controlling datasheet. Differential inputs also require both signal terminals to remain within the permitted common-mode range, even when the differential voltage itself is small.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The retrieved product and datasheet listings do not explicitly state the requested compliance statuses. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations should be confirmed using the manufacturer's current product documentation and declaration records.

Data napatotohanan sa: 2026-11-20 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MCP3302T-CI/ST datasheet MCP3302T-CI/ST specifications MCP3302T-CI/ST pinout MCP3302T-CI/ST datasheet pdf Microchip MCP3302T-CI/ST MCP3302T-CI/ST equivalent MCP3302T-CI/ST replacement MCP3302T-CI/ST cross reference MCP3302T-CI/ST price MCP3302T-CI/ST stock MCP3302T-CI/ST TSSOP-14 footprint MCP3302 13-bit differential SPI ADC MCP3302T-CI/ST battery powered sensor MCP3302T-CI/ST vs MCP3302-CI/ST 14-TSSOP 13-bit 2-channel SPI ADC

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology MCP3302T-CI/ST MCP3302-CI/ST MCP3302T-BI/ST MCP3302T-I/ST MCP3301T-BI/SN MCP3301T-BI/MS analog-to-digital converter ADC successive-approximation ADC SAR ADC low-power ADC differential input single-ended input SPI serial peripheral interface 13-bit resolution 100 ksps 2.7 V to 5.5 V 400 mV to 5 V reference 14-pin TSSOP TSSOP package surface-mount package data acquisition battery-powered sensor node
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ