MCP3302T-CI/ST - 13-Bit 4-Input SPI ADC | Microchip
MPN: MCP3302T-CI/ST ✓ 啟用中MCP3302T-CI/ST 概覽
An ADC is a data-conversion IC that transforms an analog voltage into a digital value for measurement, control, or signal processing. The MCP3302 belongs to the SAR ADC family, where a successive-approximation internal DAC compares the sampled input with successive trial voltages. Its differential-input architecture can reject common-mode noise, while single-ended operation simplifies connections for sensors, potentiometers, and resistive dividers.
Key features include 13-bit resolution, four analog inputs, two differential channels, a 100 ksps maximum conversion rate, and an SPI-compatible serial interface. According to the manufacturer datasheet, the reference voltage can range from 400 mV to 5 V. This produces input-referred resolutions between 98 µV and 1.22 mV, depending on the selected reference voltage and gain configuration.
The converter uses an internal sample-and-hold architecture and a successive-approximation conversion sequence. Differential channel selection is controlled through the serial interface, allowing two analog pairs to share one converter while maintaining consistent sampling and conversion timing. The SPI interface provides a straightforward connection to microcontrollers, although software must handle chip selection, clocking, and conversion-start timing.
Typical uses include industrial process measurement, battery-powered sensor nodes, remote data acquisition, temperature sensing with thermistors or RTDs, potentiometer position measurement, and low-voltage analog monitoring. Differential inputs are particularly useful when the measured signal is small relative to system noise or when a sensor has a ground-referenced output that cannot be connected directly to a single-ended input.
For reliable operation, keep the analog and digital return paths controlled, bypass the supply close to the device, and select a quiet reference source. Input voltage must remain within the ADC input range, and the common-mode limits of the differential inputs must be checked against the chosen reference and supply voltages before layout is finalized.
This page combines converter specifications, package and interface guidance, practical application notes, and compatible replacement analysis. It is designed to help engineers determine whether the MCP3302T-CI/ST fits a precision measurement design and how to integrate it without overlooking reference, input-range, or SPI-timing constraints.
直接替換替代品,適用於 MCP3302T-CI/ST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP3302T-CI/ST (相同外形與佔位) — 差異在於 Input Configuration, Serial Interface.
MCP3302-CI/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP3302T-BI/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP3302T-I/ST
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3302T-BI/ST
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP3302-CI/ST
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP3302T-CI/ST 最大額定值與電氣特性
| 解析度 | 13 bit |
| Input Configuration | 4 single-ended or 2 differential inputs |
| Conversion Architecture | Successive-approximation SAR ADC |
| Maximum Conversion Rate | 100 ksps |
| Tested Supply Voltage Range | 2.7 V to 5.5 V |
| Reference Voltage Range | 400 mV to 5 V |
| Minimum Input-Referred Resolution | 98 µV |
| Maximum Input-Referred Resolution | 1.22 mV |
| Serial Interface | SPI-compatible serial interface |
| 封裝 | 14-pin TSSOP |
| 安裝類型 | Surface mount |
| Analog Input Type | Differential and single-ended |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
MCP3302T-CI/ST 14-pin tssop 腳位配置指南
MCP3302T-CI/ST(14-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP3302T-CI/ST.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP3302T-CI/ST 適用於 6 應用s: Industrial Process Measurement, Battery-Powered Sensor Node, Temperature Sensing, Potentiometer Position Measurement, Remote Data Acquisition, Precision Analog Monitoring.
Industrial Process Measurement
The MCP3302T-CI/ST is appropriate for acquiring low-level industrial process signals with two differential channels or four single-ended inputs. Its differential inputs help reject common-mode voltage present on sensor wiring, while the 13-bit resolution and adjustable reference voltage support measurements in the millivolt-to-volt range. The converter reaches up to 100 ksps, allowing periodic process monitoring without excessive conversion latency. Place the sensor return and analog ground in a controlled layout, provide a low-noise reference, and ensure every input remains within the selected common-mode range. The SPI interface also allows the converter to share a bus with industrial control circuitry when chip-select and timing are managed correctly.
推薦
Battery-Powered Sensor Node
The MCP3302T-CI/ST fits remote and battery-powered sensor nodes because it combines a 2.7 V minimum operating supply with low-power operation and an SPI-compatible interface. Four single-ended inputs can monitor temperature, pressure, or resistive sensor elements, while two differential channels can improve immunity to ground offsets in longer cables. Conversion rates up to 100 ksps provide flexibility for both slow environmental measurements and faster event-based sampling. Energy use should be evaluated over the complete duty cycle, including reference behavior, digital activity, and sleep intervals. Keep the analog front end close to the converter and use a stable, low-power reference to preserve repeatability and extend operating time.
推薦
Temperature Sensing
The MCP3302T-CI/ST can digitize thermistor, RTD, or temperature-sensor signals through either single-ended or differential inputs. Differential excitation can cancel the effects of common-mode voltage and shared wiring errors, while the 13-bit output resolution supports accurate temperature interpolation over a carefully selected sensing range. The reference voltage directly influences resolution, so it should be chosen to match the sensor output while preserving sufficient headroom. Keep sensor traces away from switching nodes and connect the return path according to the sensor’s grounding method. Conversion time is normally much shorter than thermal response time, so the SPI sampling interval should be matched to the desired thermal update rate.
推薦
Potentiometer Position Measurement
The MCP3302T-CI/ST supports accurate potentiometer position readout by measuring the wiper voltage relative to one end of the resistive track. A 13-bit converter provides 8192 digital codes, and the reference range of 400 mV to 5 V allows the analog span to be matched to the potentiometer and excitation voltage. Differential operation can reduce sensitivity to reference drift or common supply disturbance, provided the track and wiper remain within the input limits. Keep the resistive track away from high-current paths to prevent resistive heating and local voltage distortion. The high conversion capability also allows the system to implement filtering or redundant readings for mechanical position systems.
推薦
Remote Data Acquisition
The MCP3302T-CI/ST is suitable for compact remote data-acquisition modules that must measure several low-energy sensors and transmit results through a serial controller. Two differential channels improve signal integrity when the acquisition node is connected to grounded or floating sensors over longer wiring runs. The 100 ksps conversion capability provides more throughput than many slowly changing environmental measurements require, while the compact 14-pin TSSOP package conserves board area. Firmware should define the full SPI transaction, sample timing, and input multiplexing sequence before production. A stable reference and careful grounding are particularly important when the converter is located far from the system controller.
推薦
Precision Analog Monitoring
The MCP3302T-CI/ST can monitor precision analog nodes in laboratory, instrumentation, and embedded-control systems where 13-bit resolution and flexible differential measurement are valuable. Its selectable reference supports multiple signal ranges, from a 400 mV minimum to a 5 V maximum, allowing one converter architecture to serve several measurement classes. The serial interface reduces pin count compared with many parallel-output ADCs, although clock and data-capture timing must be handled accurately. Use short analog traces, a low-impedance reference, and a controlled return network to maximize repeatability. For fast-changing signals, evaluate acquisition time and source settling rather than relying only on the headline conversion rate.
推薦
工程參考資料,適用於 MCP3302T-CI/ST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP3302-CI/ST | MCP3302T-BI/ST | MCP3302T-I/ST |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Resolution | 13 bit | 13 bit | 13 bit | 13 bit |
| Input Configuration | 4 single-ended or 2 differential inputs | 2-channel differential ADC | 2-channel differential ADC | 2-channel differential ADC |
| Conversion Architecture | Successive-approximation SAR ADC | Successive-approximation | Successive-approximation | Successive-approximation |
| Reference Voltage Range | 400 mV to 5 V | 400 mV to 5 V | 400 mV to 5 V | 400 mV to 5 V |
| Serial Interface | SPI-compatible | SPI | SPI | SPI |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins |
主要差異化特點
- Combines two differential channels with four single-ended inputs (對比MCP3302-CI/ST)
- Supports references from 400 mV to 5 V (對比MCP3302T-BI/ST)
- Uses a compact 14-pin TSSOP interface (對比MCP3302T-I/ST)
設計說明
Route the reference, analog inputs, and their return path away from SPI clock, digital output, and switching-node traces. Keep the reference bypass capacitor at the converter’s supply and reference pins, and provide a low-impedance ground connection. The MCP3302 can resolve down to 98 µV with a 400 mV reference, so small layout-induced errors can become significant even though the nominal converter resolution is 13 bit.
Validate the complete SPI timing rather than only the maximum nominal conversion rate. Include conversion latency, chip-select setup and hold requirements, clock polarity, and the time needed to shift 13 result bits in the firmware. Recheck analog settling at each selected gain because a source with high output impedance or excessive capacitance may require a longer acquisition interval than the conversion sequence itself.
Select the reference voltage from the required measurement span rather than using the highest permitted voltage by default. A 400 mV reference maximizes sensitivity for small signals, while a 5 V reference supports a wider input range with coarser absolute resolution. Check the reference current, converter supply current, bypass capacitance, and source impedance together so the reference remains stable during conversions.
Do not assume that a family member with the same TSSOP footprint is automatically interchangeable. Verify the exact pin functions, temperature grade, ordering code, electrical limits, and SPI timing from the controlling datasheet. Differential inputs also require both signal terminals to remain within the permitted common-mode range, even when the differential voltage itself is small.
合規資訊
The retrieved product and datasheet listings do not explicitly state the requested compliance statuses. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations should be confirmed using the manufacturer's current product documentation and declaration records.