Microchip Technology

MCP651-E/SN - 50MHz Rail-to-Rail Op Amp | Microchip

MPN: MCP651-E/SN ✓ Nakahanda
150 µV Vdss 6 mA Id 8-pin SOIC Package
MOQ: 1 |

MCP651-E/SN Ulas

Microchip Technology MCP651-E/SN is a single-circuit, 50 MHz operational amplifier with rail-to-rail input and output capability, 1.8 V operation, and automatic offset calibration using mCal. The device is supplied in an 8-pin SOIC package and is intended for low-cost, low-power, high-precision signal-conditioning applications. Its 50 MHz gain-bandwidth product supports higher-bandwidth amplification than conventional general-purpose op amps, while the 150 µV low-offset figure improves DC accuracy after calibration.

An operational amplifier is an analog integrated circuit that uses external feedback to amplify the difference between two input voltages. The MCP651 belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, general-purpose amplifiers, instrumentation amplifiers, and other analog signal-conditioning ICs. Its rail-to-rail input and output behavior increases usable signal range in low-voltage systems where the output must approach the supply rails.

Key characteristics include a 50 MHz gain-bandwidth product, operation down to 1.8 V, and mCal self-calibration at power-up. The mCal function is intended to reduce input offset voltage and improve precision without requiring a manual trim procedure. Rail-to-rail inputs support sensing signals near either supply rail, while the single-amplifier configuration reduces board area in designs that need only one high-speed amplifier.

The MCP65x family is manufactured using Microchip CMOS technology and is built for low-cost, low-power, high-precision signal conditioning. At power-up, the amplifier performs its offset calibration, making it useful where fixed offset error would otherwise degrade measurement accuracy. The operating range and low-voltage capability are particularly valuable for battery-powered instruments, portable sensors, and mixed-signal systems operating from compact supply rails.

Typical applications include sensor-signal conditioning, low-level instrumentation, active filtering, audio and communication interfaces, portable measurement equipment, and general-purpose analog buffers. The 50 MHz bandwidth can support signal paths above audio frequency when required, although stability, output drive, and noise characteristics must be evaluated for the specific gain and load configuration.

For PCB design, route the input and feedback paths compactly, maintain short ground returns, and decouple the supply pins close to the device. Because the amplifier includes automatic calibration, allow the circuit to operate from a stable supply during startup and verify system behavior across the intended temperature range. Do not assume that rail-to-rail operation eliminates all headroom or output-current restrictions; consult the manufacturer datasheet for the complete electrical limits and typical curves.

This page combines the manufacturer electrical description, package information, pin assignment, drop-in alternatives, application guidance, and design-focused comparison points for engineers evaluating MCP651-E/SN in precision analog signal paths.

Mga alternatibo na pwedeng ilagay na MCP651-E/SN — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MCP651-E/SN (parehas na form factor at footprint) — pagkakaiba sa Gain-Bandwidth Product, Package, Common-Mode Rejection Ratio, Input Bias Current, Number of Amplifiers.

Microchip Technology
Gain-Bandwidth Product: 20 MHz
Number of Amplifiers: 1 circuit
Microchip Technology
Gain-Bandwidth Product: 50 MHz typical
Common-Mode Rejection Ratio: 81 dB typical
Input Bias Current: 0.0050 uA
Microchip Technology
Gain-Bandwidth Product: 60 MHz typical
Package: 8-SOIC, 0.154 inch body width, 3.90 mm width
Common-Mode Rejection Ratio: 79 dB typical

MCP651T-E/SN

✅ Drop-In
📦 8-SOIC
Same MCP651 family and 50 MHz gain-bandwidth rating; ordering-option behavior may differ by 0 MHz in bandwidth, so verify temperature grade and calibration details

📋 Alternatibo na Reference (hindi sa katalogo)

MCP652-E/SN

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 8-SOIC
2 circuits · 50 MHz typical · 30 V/us typical · 2.5 V · 7.5 nV/Hz typical at 1 MHz · +/-200 uV maximum · 81 dB typical · 100 mA typical

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP653-E/SN

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-SOIC
Same MCP65x family, rail-to-rail single-amplifier architecture, and 8-pin SOIC footprint; family-specific bandwidth and offset limits differ from the 50 MHz MCP651 target

📋 Alternatibo na Reference (hindi sa katalogo)

MCP654-E/SN

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-SOIC
Same MCP65x family and 8-pin SOIC package; the alternative has a different family-specific gain-bandwidth rating while retaining a minimum supply voltage of 1.8 V

📋 Alternatibo na Reference (hindi sa katalogo)

MCP655-E/SN

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-SOIC
Same MCP65x family, 1.8 V minimum supply, and 8-pin SOIC format; gain-bandwidth and feature differences require datasheet verification against the MCP651's 50 MHz rating

📋 Alternatibo na Reference (hindi sa katalogo)

MCP661-E/SN

✅ Drop-In
Microchip Technology
📦 8-SOIC
Single operational amplifier · 60 MHz typical · 32 V/µs typical · 2.5 V minimum · Rail-to-rail output · 90 mA typical · 6.8 nV/√Hz typical at 1 MHz · 79 dB typical

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP651-E/SN Mga Pinakamataas na Rating at Electrical Characteristics

Amplifier Type Single operational amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 50 MHz
Input Offset Voltage 150 µV
Minimum Supply Voltage 1.8 V
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Offset Calibration mCal automatic power-up calibration
Process Technology CMOS
Kuru-kuryente ng Pagbibigay 6 mA
Packhaging 8-pin SOIC
Bilang ng Pin 8 pins
Uri ng Pagpapasok Surface mount
Product Type Standard general-purpose amplifier
Qualification Temperature Grade -40°C to +125°C

Pin Configuration ng MCP651-E/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 NC — Not connected
Pin 2 IN- — Inverting input
Pin 3 IN+ — Non-inverting input
Pin 4 V- — Negative power supply
Pin 5 NC — Not connected
Pin 6 OUT — Amplifier output
Pin 7 V+ — Positive power supply
Pin 8 NC — Not connected

Tipikal na mga Gamit

MCP651-E/SN ay nararapat para sa 6 aplikasyons: Low-Voltage Sensor Signal Conditioning, Portable Measurement Instrumentation, Active Filtering and Signal Conditioning, Battery-Powered Analog Interfaces, Audio and Communication Buffering, Precision Analog Signal Conditioning.

🧩

Low-Voltage Sensor Signal Conditioning

MCP651-E/SN fits low-voltage sensor front ends because its rail-to-rail input and output operation preserves signal range from a 1.8 V supply. The 150 µV low-offset specification and mCal startup calibration improve DC accuracy when the source impedance and signal bandwidth allow those benefits to dominate. A practical implementation places the sensor near the amplifier inputs, keeps the feedback network compact, and follows the sensor interface with a low-pass filter. The 50 MHz gain-bandwidth product leaves bandwidth above the sensor signal range, while rail-to-rail output simplifies connection to a low-voltage ADC or comparator. Verify input bias current, noise, settling time, and capacitive loading before fixing the gain and filter values.

📊

Portable Measurement Instrumentation

The MCP651-E/SN is appropriate for compact measurement instruments that operate from low-voltage rails. Operation down to 1.8 V reduces the need for a higher-voltage analog supply, while mCal performs offset calibration at power-up and supports repeatable DC measurements. The single-amplifier 8-pin SOIC package leaves board area for the sensor, display interface, and data-acquisition circuitry. In a typical instrument chain, the amplifier scales a transducer output before an ADC samples the result. Place the input path close to the sensor, use stable precision resistors, and evaluate offset drift over temperature rather than assuming startup calibration removes every source of error.

📡

Active Filtering and Signal Conditioning

MCP651-E/SN can implement active filters and general signal-conditioning stages when the required closed-loop bandwidth remains consistent with its 50 MHz gain-bandwidth product. Rail-to-rail inputs and outputs make the amplifier useful for filters centered on mid-supply signals or operating near a rail in a compact 1.8 V system. Build the filter from precision resistors and capacitors, and keep feedback loops physically small to reduce parasitic coupling. Gain, noise, and phase margin must be checked together because the gain-bandwidth value is not a guarantee that every filter topology will remain stable with the selected tolerance and load.

🔋

Battery-Powered Analog Interfaces

MCP651-E/SN is suited to battery-powered analog interfaces because its minimum supply voltage is 1.8 V and its input and output can operate rail-to-rail. These characteristics help a designer use more of the available supply range rather than restricting signals to a narrow central region. The amplifier can buffer a sensor, level-shift a logic-domain reference, or provide gain ahead of an ADC. Power-budget decisions should still account for the specified 6 mA supply-current class, mCal startup behavior, and leakage into the source network. Use local supply decoupling and verify that shutdown sequencing does not create an input overvoltage outside the manufacturer's absolute maximum ratings.

🎧

Audio and Communication Buffering

MCP651-E/SN can buffer higher-bandwidth analog signals in audio and communication equipment. Its 50 MHz gain-bandwidth product provides substantially more bandwidth than a typical low-frequency precision amplifier, while rail-to-rail input and output behavior supports operation from a compact supply. Place the amplifier where it can drive the intended load without long traces, and use a feedback topology appropriate for the required gain and bandwidth. Output-drive, output-noise, distortion, and capacitive-load limits must be taken from the manufacturer data sheet; these characteristics are not established solely by the 50 MHz headline bandwidth.

🔧

Precision Analog Signal Conditioning

MCP651-E/SN provides a combination of low offset, automatic calibration, and 50 MHz bandwidth for precision signal-conditioning designs where DC accuracy and moderate bandwidth matter in the same stage. mCal calibrates the amplifier at power-up, reducing the influence of initial input offset. A practical circuit places the amplifier close to the precision feedback resistors and the analog source, while a nearby bypass capacitor provides a low-impedance supply reference. Confirm the offset-error distribution, calibration time, input bias current, and temperature drift against the system error budget before using the device as the final precision amplifier in a high-gain chain.

Buod ng mga Inirekomendang Produkto

What are the key specifications of MCP651-E/SN that engineers should know?
The MCP651-E/SN is a single 50 MHz operational amplifier with rail-to-rail input and output operation, supply operation down to 1.8 V, and automatic power-up offset calibration using mCal. According to the Microchip MCP651 product page and the manufacturer MCP65x data sheet, the device also has a 150 µV low-offset specification and uses CMOS process technology. It is packaged in an 8-pin SOIC, making it appropriate for compact, surface-mounted precision analog designs.
What is MCP651-E/SN and what does the mCal function do?
MCP651-E/SN is a single, 50 MHz, rail-to-rail operational amplifier that calibrates its offset at power-up using mCal. Microchip states that the MCP65x family uses mCal to self-calibrate at startup, improving offset accuracy without a manual trim procedure. The 1.8 V minimum operating supply and rail-to-rail input/output characteristics make the amplifier suitable for low-voltage signal-conditioning circuits, including portable instrumentation and sensor interfaces.
Where can I download the MCP651-E/SN datasheet PDF?
The official MCP65x family data sheet is available from Microchip at the documented DeviceDoc link on this page. It covers MCP651 and related devices, including electrical characteristics, mCal operation, package information, and application guidance. Use that manufacturer document for the definitive MCP651-E/SN pin descriptions, absolute maximum ratings, supply-voltage limits, typical performance curves, and ordering information before completing the PCB footprint or production BOM.
Where can I find the MCP651-E/SN pinout?
The MCP651-E/SN pin assignment is shown in the 8-pin SOIC package data on this page and must be checked against the manufacturer pin-description table. The standard single-amplifier connection uses the two input pins, output, supply rails, and the package pins designated NC. Do not assign a function to an NC pin based only on package numbering; verify the exact mechanical drawing and pin table in the Microchip MCP65x data sheet before routing.
Is MCP651-E/SN suitable for low-voltage sensor signal conditioning?
Yes, MCP651-E/SN is well matched to low-voltage sensor signal conditioning because it operates down to 1.8 V and accepts and produces rail-to-rail signals. The manufacturer identifies low offset, mCal startup calibration, and a 50 MHz gain-bandwidth product as principal characteristics of the MCP65x family. These features help preserve signal range and accuracy, although sensor noise, source impedance, ADC requirements, and filter stability still determine the final signal-chain performance.
Where can I buy MCP651-E/SN online?
MCP651-E/SN can be requested through the Request a Quote form on this page, where package, quantity, delivery, and sourcing requirements can be reviewed with XAIPART. The part is identified as a Microchip Technology single amplifier in an 8-pin SOIC package. Confirm the exact suffix, operating-temperature grade, and delivery quantity during the quotation process rather than substituting a mechanically similar device without verifying its electrical behavior.
What is the price of MCP651-E/SN?
The current commercial terms for MCP651-E/SN should be obtained through the Request a Quote form on this page. The form captures the required quantity, package suffix, and delivery conditions needed to prepare an accurate quotation. No static price is used here because market pricing and availability can change independently of the device's technical specification, and a quote ensures that the requested ordering configuration is reviewed.
What is the lead time for MCP651-E/SN?
The current lead time for MCP651-E/SN should be confirmed through the Request a Quote form on this page. Lead time can vary with the order quantity, manufacturing schedule, and the exact ordering suffix, so a quantity-specific confirmation is preferable to a generic availability statement. Include the required delivery date and production schedule in the request to allow the most relevant supply commitment to be evaluated.
Is MCP651-E/SN in stock?
Current stock for MCP651-E/SN should be checked through the Request a Quote form on this page. Provide the required quantity and target date so XAIPART can confirm the appropriate supply position for the exact 8-pin SOIC ordering configuration. The technical designation as a standard general-purpose amplifier identifies the device family, but it does not by itself guarantee immediate availability for a particular order quantity.
MCP651-E/SN vs MCP661-E/SN: which is better for a 50 MHz signal path?
MCP651-E/SN is the safer choice when compatibility with the documented MCP651 family and its 50 MHz rail-to-rail operating characteristics is the priority. MCP661-E/SN appears in the cross-reference material as a comparable single amplifier with low offset, operation down to 1.8 V, and rail-to-rail inputs and outputs, but its family-specific specifications must be reviewed before substitution. Existing MCP651-E/SN layouts should also be checked against the MCP661 data sheet rather than assuming every electrical limit is identical.
What is the difference between MCP651-E/SN and MCP661-E/SN?
Both MCP651-E/SN and MCP661-E/SN are represented as single, rail-to-rail operational amplifiers with operation down to 1.8 V and low-offset capability. The documented comparison does not establish that every gain, bandwidth, current, stability, or calibration characteristic is identical, so engineers should compare the relevant values in the Microchip MCP65x data sheet and the MCP661 documentation. The cross-reference listing supports functional similarity but does not replace a final footprint and electrical review.
When should I choose MCP651-E/SN over MCP661-E/SN?
Choose MCP651-E/SN when the design specifically requires the MCP651 family's 50 MHz amplifier behavior, mCal startup calibration, and established 8-pin SOIC implementation. Choose MCP661-E/SN only after confirming that its datasheet satisfies the required bandwidth, input impedance, output drive, noise, stability, and power conditions for the same schematic. This is particularly important for high-gain, precision, or low-noise circuits where a close headline specification does not guarantee equivalent system performance.
What can replace MCP651-E/SN on the same PCB?
MCP651-E/SN can be replaced by a device only when its package, pinout, supply range, input/output range, bandwidth, stability, and calibration behavior are all compatible with the existing design. MCP651T-E/SN is a close same-family candidate identified in comparison data, while MCP661-E/SN is a cross-family candidate identified in the cross-reference material. Both require a manufacturer-datasheet review because the comparison snippets do not prove complete electrical equivalence.
Is MCP651-E/SN the same as MCP651T-E/SN?
No, MCP651-E/SN and MCP651T-E/SN are related ordering variants rather than necessarily identical package-and-temperature combinations. The cross-reference results explicitly identify MCP651T-E/SN as a comparable candidate, but the suffix may encode package, temperature, or qualification differences that affect land-pattern compatibility. Confirm the full ordering code, package dimensions, pin arrangement, temperature grade, and absolute maximum ratings in the Microchip ordering information before replacing one with the other.
What is the best Microchip equivalent for MCP651-E/SN?
The best Microchip equivalent is the member of the MCP65x family whose full ordering code matches the required 8-pin SOIC footprint, temperature range, calibration method, and electrical limits. MCP651T-E/SN is a documented same-family candidate, and MCP652-E/SN through MCP655-E/SN belong to the broader family named in the manufacturer data sheet. Because the family includes devices with different feature sets, do not choose an equivalent by amplifier count or bandwidth alone; confirm the pinout and full parameter set first.
Can MCP651-E/SN be used in audio and communication interfaces?
Yes, MCP651-E/SN can be used in audio and communication-interface signal paths when the required signal bandwidth and loading are compatible with its 50 MHz gain-bandwidth product. Rail-to-rail inputs and outputs are useful when the signal spans much of the available supply range. Designers should still evaluate output-current capability, noise, distortion, stability with the selected feedback network, and the bandwidth required by the actual channel rather than treating the gain-bandwidth figure as a guaranteed small-signal operating bandwidth.

Impormasyon ng Talumpati sa Engineering for MCP651-E/SN — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MCP651-E/SN when the design needs a single rail-to-rail amplifier operating from 1.8 V, with 50 MHz gain-bandwidth, low offset, and mCal startup calibration in an 8-pin SOIC. It is a strong fit for compact sensor front ends, precision analog signal conditioning, active filtering, portable instruments, and moderate-bandwidth communication interfaces. MCP651T-E/SN is the closest documented same-family candidate, but its full suffix, temperature grade, and pin requirements should be checked before substitution. MCP652-E/SN through MCP655-E/SN are useful MCP65x alternatives when their family-specific features better match the circuit, but none should replace the target solely because it uses the same family. MCP661-E/SN may suit a comparable low-voltage rail-to-rail design, yet it must be selected from its own datasheet rather than treated as electrically identical. For all alternatives, verify package dimensions, pinout, supply limits, offset behavior, bandwidth, output drive, noise, and stability against the existing schematic.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MCP651T-E/SN MCP652-E/SN MCP653-E/SN MCP654-E/SN MCP655-E/SN
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Amplifier Count 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Minimum Supply Voltage 1.8 V 1.8 V 1.8 V 1.8 V 1.8 V 1.8 V
Input Common-Mode Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Offset Calibration mCal automatic power-up calibration MCP65x-family power-up calibration feature MCP65x-family power-up calibration feature MCP65x-family power-up calibration feature MCP65x-family power-up calibration feature MCP65x-family power-up calibration feature
Process Technology CMOS CMOS CMOS CMOS CMOS CMOS
Special Features Standard general-purpose amplifier MCP651-family general-purpose amplifier MCP652-family function MCP653-family function MCP654-family function MCP655-family function

Pangunahing mga Pagkakaiba

  • Combines 50 MHz bandwidth with automatic power-up offset calibration (kumpara saMCP661-E/SN)
  • Supports operation from a 1.8 V supply with rail-to-rail signal range (kumpara saMCP652-E/SN)
  • Provides a standard single-amplifier 8-SOIC implementation (kumpara saMCP655-E/SN)

Talaan ng Disenyo

Keep the op-amp input pins and feedback components away from switching nodes, high-current traces, and the supply-return path. Place the input and feedback components close to pins 2, 3, and 6, and use a continuous ground plane where practical. For a single-supply circuit, connect V+ and V- to their respective bypass capacitors and return them directly to the ground plane. This reduces parasitic pickup and helps the amplifier retain the benefit of its 50 MHz bandwidth.

Use the 1.8 V minimum operating capability as the lower design boundary, not as a target for new designs. Provide normal supply margin above 1.8 V because the exact allowed range, startup behavior, and absolute maximum limits must be confirmed in the manufacturer data sheet. Place the supply bypass capacitor close to the device and keep its ground connection short. Treat mCal as a startup event and avoid switching the supply repeatedly without reviewing the resulting system behavior.

Do not assume that rail-to-rail input and output operation permits operation beyond the supply rails or eliminates output headroom. Check output-current capability, output-voltage limits at the selected load, input common-mode limits, and stability with the selected feedback network. A 50 MHz gain-bandwidth product does not guarantee 50 MHz usable closed-loop bandwidth at every gain. Confirm the exact MCP651-E/SN ordering suffix and pin description against the manufacturer data sheet before releasing a PCB.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified. Confirm the current compliance and qualification information with the manufacturer before using the device in regulated production.

Data napatotohanan sa: 2026-11-10 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MCP651-E/SN MCP651-E/SN datasheet MCP651-E/SN datasheet pdf MCP651-E/SN pinout MCP651-E/SN specifications Microchip MCP651-E/SN MCP651-E/SN 50 MHz op amp MCP651-E/SN 8-SOIC MCP651-E/SN equivalent MCP651-E/SN replacement MCP651-E/SN cross reference MCP651-E/SN vs MCP661-E/SN MCP651-E/SN application circuit MCP651-E/SN price MCP651-E/SN stock

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology MCP651-E/SN MCP651T-E/SN MCP652-E/SN MCP653-E/SN MCP654-E/SN MCP655-E/SN MCP661-E/SN operational amplifier op amp analog amplifier signal-conditioning IC rail-to-rail input rail-to-rail output mCal automatic offset calibration gain-bandwidth product input offset voltage CMOS 8-SOIC SOIC package surface-mount package low-voltage analog precision signal conditioning
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ