MSP430F2002IPW - 16MHz 1KB Flash MCU | Texas Instruments
MPN: MSP430F2002IPW ✓ NakahandaMSP430F2002IPW Ulas
A mixed-signal microcontroller is a semiconductor device that combines digital control logic with analog measurement or comparison functions. The MSP430 belongs to the broader hierarchy of embedded MCU, processor, and semiconductor products. Its architecture is designed for compact control systems in which low energy consumption, deterministic operation, and integrated sensing can reduce the number of external components.
The principal benefits of the MSP430F2002IPW include its 16 MHz operating clock, 1 KB Flash program memory, 128 B SRAM, and five low-power operating modes. The 10-bit ADC supports embedded measurement without requiring a separate converter, while the comparator supports threshold detection and basic signal conditioning. SPI and I2C interfaces allow the controller to communicate with sensors, memories, transceivers, and other low-speed peripherals.
The MSP430 uses a 16-bit RISC CPU with 16-bit registers, providing efficient execution for sensor acquisition, control loops, timing, and low-power state management. Five low-power modes are particularly valuable in battery-powered equipment because firmware can disable unused peripherals and place the MCU into a lower-energy state between measurement or communications events.
Typical uses include portable measurement instruments, compact industrial sensors, low-power data loggers, battery-operated monitoring modules, and embedded control systems with analog inputs. Its integrated ADC, comparator, timer, and serial interfaces make it especially appropriate for designs in which board area and standby energy are more important than large program-memory capacity.
When designing around this MCU, confirm that the application code, boot configuration, communication stack, and calibration data fit within the 1 KB Flash and 128 B SRAM limits. Use the manufacturer pin-description table when assigning PCB tracks, and follow the recommended decoupling and exposed-ground-layout guidance for the 14-pin TSSOP package.
This page consolidates the device identity, memory and peripheral details, commercial information, same-family replacement options, comparison parameters, and practical PCB guidance into one engineering-focused reference for designers evaluating the MSP430F2002IPW.
Mga alternatibo na pwedeng ilagay na MSP430F2002IPW — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MSP430F2002IPW (parehas na form factor at footprint) — pagkakaiba sa ADC Resolution, Flash Memory, Package, SRAM.
MSP430F2001IPW
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MSP430F2003IPW
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MSP430F2011IPW
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MSP430F2012IPW
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →MSP430F2013IPW
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
MSP430F2002IPW Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 16-bit ultra-low-power mixed-signal microcontroller |
| Maksimum na Taktiko ng Oras | 16 MHz |
| CPU Architecture | 16-bit RISC |
| Register Width | 16 bit |
| Flash Memory | 1 KB |
| SRAM | 128 B |
| ADC Resolution | 10 bit |
| Analog Comparator | 1 integrated comparator |
| Timer | 1 integrated 16-bit timer |
| Serial Interfaces | SPI and I2C |
| General-Purpose I/O Pins | 10 pins |
| Low-Power Modes | 5 modes |
| Packhaging | 14-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng MSP430F2002IPW 14-pin tssop
Pin configuration para sa MSP430F2002IPW (14-pin tssop package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa MSP430F2002IPW.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MSP430F2002IPW ay nararapat para sa 6 aplikasyons: Portable Data Logger, Industrial Sensor Interface, Battery-Powered Monitor, Embedded Control Module, Digital Potentiometer Control, Low-Power Communication Node.
Portable Data Logger
The MSP430F2002IPW fits portable data loggers that periodically measure an analog input and then sleep between samples. Its 16 MHz CPU executes acquisition, scaling, and storage-control routines, while the integrated 10-bit ADC reduces the need for a separate converter. The five low-power modes are especially valuable for battery-operated equipment because firmware can disable unused blocks between measurements. The main constraint is memory: only 1 KB of Flash and 128 B of SRAM are available, so designers should minimize buffers, store dense sampled data externally, and avoid resource-heavy middleware.
Inirekomenda
Industrial Sensor Interface
The MSP430F2002IPW is useful for compact industrial sensor interfaces where a 10-bit measurement, threshold decision, and serial reporting must be handled locally. Its analog comparator can perform fast threshold detection, while the ADC provides a sampled signal for filtering and calibration. SPI and I2C permit connection to industrial sensors or external signal-conditioning devices. For robust operation, keep the sensor path away from switching nodes, provide local supply bypassing, and use the device’s low-power modes only after confirming that the selected sensor and interface circuitry tolerate the resulting wake-up interval.
Inirekomenda
Battery-Powered Monitor
A battery-powered environmental or equipment monitor can use the MSP430F2002IPW to combine measurement, comparison, and communications in one 14-pin device. The 10-bit ADC supports basic level or condition monitoring, and the comparator can implement threshold events without continuously running conversion software. The five low-power modes allow the MCU to remain asleep during long idle intervals and wake for periodic measurements. Designers should select external sensors with low standby demand, keep leakage paths off analog inputs, and size storage and communications so that processing after wake-up does not compromise the intended battery life.
Inirekomenda
Embedded Control Module
The MSP430F2002IPW can serve as the central controller in a small embedded module that accepts digital commands, drives an actuator interface, and monitors a sensor signal. Its 16-bit RISC core and ten I/O pins provide enough parallelism for basic sequencing and timing, while SPI or I2C handles slower peripheral traffic. Because the 14-pin package has limited I/O, priority signals should be assigned to the pins with the required timer or interrupt functions. Firmware should use the timer as the timing reference and place repetitive processing into interrupt service routines to maintain predictable response behavior.
Inirekomenda
Digital Potentiometer Control
The MSP430F2002IPW is appropriate for controlling a digital potentiometer or similar SPI-compatible actuator in compact analog systems. The SPI interface shares the MCU with the ADC and comparator, allowing a firmware loop to read a measured value, compare it with a target, and update the actuator. The 16 MHz clock provides ample execution margin for simple control calculations, while low-power modes help reduce consumption when the actuator does not need continuous updating. The tight memory limits require concise control code and careful buffer allocation, especially if local calibration data must also be retained.
Inirekomenda
Low-Power Communication Node
The MSP430F2002IPW can act as a low-power communication node when a design must connect a sensor or simple control point to an SPI or I2C bus. The MCU can format measurements, manage acknowledgements, and enter a low-power state between transactions. Its 10-bit ADC supports local analog supervision, and the timer can establish communication or sampling intervals. Bus reliability depends on correct pull-up placement, signal-level compatibility, and isolation from noisy power stages. Firmware should define timeout and recovery behavior because the limited RAM constrains buffering for complex protocol stacks.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MSP430F2002IPW — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MSP430F2001IPW | MSP430F2003IPW | MSP430F2011IPW | MSP430F2012IPW | MSP430F2013IPW |
|---|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Flash Memory | 1 KB | 1 KB | 1 KB | 2 KB | 2 KB | 2 KB |
Pangunahing mga Pagkakaiba
- Combines control, measurement, comparison, and serial communication in one 14-pin device (kumpara saMSP430F2001IPW)
- Higher ADC resolution is available in the same family (kumpara saMSP430F2003IPW)
- Balanced memory and ADC configuration for compact acquisition systems (kumpara saMSP430F2012IPW)
- Compact 14-TSSOP implementation for space-constrained boards (kumpara saMSP430F133IPMR)
Talaan ng Disenyo
Place the MCU and its required support components using the manufacturer land pattern for the 14-pin TSSOP. Keep analog inputs away from digital return paths, provide a continuous ground reference, and route decoupling current with a short path to the supply and ground pins. Confirm exposed-pad requirements from the package drawing before release because land-pattern assumptions can create assembly or soldering defects.
Design the supply path for low-voltage MCU operation and validate startup behavior across the full intended voltage range. Place local bulk and high-frequency bypass capacitors at the device entry points, use the capacitor values and placement directed by the manufacturer datasheet, and avoid routing switching-regulator currents through analog-reference areas. The five low-power modes reduce demand only when external peripherals and analog networks are placed in compatible low-leakage states.
Do not treat the MSP430F2002IPW as a general-purpose MCU with ample memory: its 1 KB Flash and 128 B SRAM impose strict limits on buffering, protocol stacks, and calibration tables. Estimate peak stack depth, use the smallest practical data types, and move bulky data to external storage. Changes to the MSP430F2001IPW or MSP430F2003IPW should include a complete firmware review because ADC and peripheral behavior differ.
Treat SPI and I2C routing as short, continuous communication paths, especially when the MSP430F2002IPW operates at 16 MHz. Match trace lengths where timing margins are narrow, avoid crossing switching-node boundaries, and keep pull-up placement close to the relevant bus devices. The ADC reference and analog input paths require separate attention from digital bus routing to prevent coupling from introducing measurement errors.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page and family datasheet identify the device and its quality information, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were included. AEC-Q100 is not applicable to this general-purpose microcontroller.