OPA237UA - 1.5MHz Single-Supply Op Amp | Texas Instruments
MPN: OPA237UA ✓ NakahandaOPA237UA Ulas
An operational amplifier is a voltage-gain element that uses feedback to amplify the difference between its non-inverting and inverting inputs. The OPA237 family is optimized for operation from a single positive supply, including systems powered by batteries or low-voltage industrial rails. Its topology and electrical characteristics make it suitable for buffering, current sensing, analog measurement, filtering, and precision control. A single-amplifier package also allows designers to conserve board area when only one amplifier channel is required.
Key performance characteristics include a 1.5 MHz gain-bandwidth product for moderate-frequency analog signals and a 0.5 V/µs slew rate for large-signal response. The stated 78 dB common-mode rejection ratio helps reject common-mode interference, while the stated 100 dB power-supply rejection ratio indicates strong isolation from supply ripple. An 8 mA output-current capability supports the input and output stages required by typical low-power analog circuits.
OPA237UA operates from a 2.7 V to 36 V supply, enabling use across low-voltage battery systems and higher-voltage industrial equipment. Its single-supply architecture supports input and output signals referenced near ground when appropriate for the selected feedback network. The 8-pin SOIC footprint is suitable for conventional surface-mount assembly and board-level replacement planning, although input bias, offset, noise, stability, and output-swing constraints must be checked against the actual application.
Typical uses include low-side current measurement, sensor amplification, active filtering, transducer interfaces, buffered analog inputs, and precision control loops. The 1.5 MHz bandwidth is particularly appropriate for slow sensor signals, instrumentation, and general-purpose signal conditioning rather than high-frequency video or RF amplification. The 36 V maximum supply also makes the device useful in industrial systems where signal amplitudes and supply transients exceed typical consumer levels.
Designers should place input, feedback, and bypass components close to the amplifier pins to minimize parasitic feedback and maintain signal integrity. The SOIC package offers a practical thermal path on a conventional PCB, but sustained output current still requires careful assessment of power dissipation, copper area, and adjacent heat sources. Stable operation also depends on selecting feedback values compatible with the device’s gain-bandwidth and output-drive characteristics.
This page combines manufacturer specifications, package and pin information, drop-in replacement guidance, application-focused design notes, and parameter comparisons. It provides practical context for evaluating the OPA237UA alongside other single-amplifier choices while keeping circuit compatibility, supply range, bandwidth, and package constraints visible.
Mga alternatibo na pwedeng ilagay na OPA237UA — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
OPA237UA/2K5G4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
OPA237UA Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 1.5 MHz |
| Slew Rate | 0.5 V/µs |
| Supply Voltage Range | 2.7 V to 36 V |
| Common-Mode Rejection Ratio | 78 dB |
| Power-Supply Rejection Ratio | 100 dB |
| Output Current | 8 mA |
| Number of Channels | 1 channel |
| Packhaging | 8-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Supply Type | Single supply |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
Pin Configuration ng OPA237UA
| Pin 1 | NC — Not connected (per datasheet) |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected (per datasheet) |
| Pin 6 | OUT — Amplifier output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected (per datasheet) |
Tipikal na mga Gamit
OPA237UA ay nararapat para sa 6 aplikasyons: Low-Side Current Sensing, Sensor Signal Conditioning, Active Analog Filtering, Industrial Analog Measurement, Battery-Powered Instrumentation, Precision Control Loops.
Low-Side Current Sensing
OPA237UA fits low-side current measurements because its 1.5 MHz gain-bandwidth product can amplify the small voltage generated by a shunt without adding substantial bandwidth limitations. The stated 78 dB common-mode rejection ratio helps reject voltage shared by the shunt, supply, and measurement ground, while the 2.7 V to 36 V supply range supports both compact battery-powered monitors and industrial measurement circuits. Place the amplifier close to the shunt and ADC input to minimize copper resistance and parasitic pickup. Check the common-mode input range at the selected supply voltage before finalizing the gain and shunt resistance.
Inirekomenda
Sensor Signal Conditioning
OPA237UA can amplify and buffer resistive sensor outputs such as thermistors, potentiometers, and resistive bridges when the signal bandwidth remains below its 1.5 MHz gain-bandwidth product. Its low-power single-supply operation is useful for portable instrumentation, and the 36 V maximum supply provides additional range for industrial sensor interfaces. The 100 dB power-supply rejection ratio helps prevent supply ripple from appearing at the conditioned output. Use resistor values that preserve the required closed-loop gain and verify sensor excitation current, input bias error, and output headroom.
Inirekomenda
Active Analog Filtering
OPA237UA is appropriate for first-order or modest higher-order active filters operating at low-to-moderate frequencies. Its 1.5 MHz gain-bandwidth product provides bandwidth beyond many sensor-band applications, while the 0.5 V/µs slew rate must be checked against the filter’s largest expected output transitions. The single 8-pin SOIC package simplifies designs that require one noninverting or inverting active-filter stage. Component tolerances and amplifier noise should be included when determining filter cutoff accuracy, and the completed circuit should be stability-checked across its full input and output signal range.
Inirekomenda
Industrial Analog Measurement
OPA237UA supports industrial analog measurement front ends where signals must be conditioned before conversion or control. Its supply range extends to 36 V, permitting use in systems with a higher nominal rail than ordinary low-voltage consumer circuits. The 78 dB common-mode rejection ratio is valuable when the measurement input includes substantial common-mode voltage, and the 100 dB power-supply rejection ratio helps isolate the signal path from supply variation. The amplifier still requires adequate transient protection, grounding, and input-range analysis for industrial surge and ground-offset conditions.
Inirekomenda
Battery-Powered Instrumentation
OPA237UA is suitable for portable, battery-powered instruments because it is designed as a single-supply amplifier and can operate from rails as low as 2.7 V. A 1.5 MHz bandwidth is suitable for many physiological, environmental, and general-purpose sensor signals without requiring a high-speed amplifier. Low-voltage operation requires careful attention to output swing and common-mode headroom, particularly near the lower supply limit. Select resistor and reference networks that keep the signal inside those limits, and use local supply bypassing to reduce supply ripple coupled into the measurement chain.
Inirekomenda
Precision Control Loops
OPA237UA can serve as the error amplifier in low-frequency control and feedback systems where loop bandwidth remains well below its 1.5 MHz gain-bandwidth product. The 0.5 V/µs slew rate provides finite large-signal response, so loop compensation must account for the rate at which the control output can move. Single-supply operation simplifies systems whose actuator and sensor share a positive rail, while the 36 V upper limit permits use in higher-voltage control platforms. Verify startup behavior, output saturation limits, and noise before closing the loop around the selected actuator.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for OPA237UA — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | OPA237UA/2K5G4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint |
| Amplifier Channels | 1 channel | 1 channel |
| Supply Range | 2.7 V to 36 V | 2.7 V to 36 V |
| Gain-Bandwidth Product | 1.5 MHz | 1.5 MHz |
| Slew Rate | 0.5 V/µs | 0.5 V/µs |
| Common-Mode Rejection Ratio | 78 dB | 78 dB |
| Power-Supply Rejection Ratio | 100 dB | 100 dB |
| Output Current | 8 mA | 8 mA |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Ordering Configuration | OPA237UA | OPA237UA/2K5G4 with 2,500-unit reel packaging |
| Price Tier | Request a Quote | Request a Quote |
Pangunahing mga Pagkakaiba
- Direct single-amplifier ordering option in an 8-pin SOIC (kumpara saOPA237UA/2K5G4)
- Wide supply-range capability in a compact single channel (kumpara saOPA237UA/2K5G4)
- Same electrical configuration for manufacturing substitution (kumpara saOPA237UA/2K5G4)
Talaan ng Disenyo
Place the amplifier, input components, feedback resistors, and supply-bypass capacitor close together to minimize parasitic feedback and high-frequency coupling. Keep the inverting-input trace short because it is especially sensitive to capacitance from adjacent signals. For a noninverting configuration, connect the feedback network directly to pins 2 and 6 and place the bypass capacitor between pins 7 and 4 near the package.
The OPA237UA supply range extends to 36 V, but the actual power dissipation depends on supply voltage, output voltage, quiescent current, and load current. Estimated maximum package dissipation can be calculated as PD ≈ (V+ − |VOUT|) × IOUT plus internal losses; verify the result against the manufacturer’s maximum power and temperature-rise limits before operating near the upper supply limit.
Account for the 1.5 MHz gain-bandwidth product when selecting closed-loop gain. A higher gain reduces usable signal bandwidth, while a 0.5 V/µs slew rate can limit large-signal output response even when small-signal bandwidth appears adequate. Use the Texas Instruments OPA237 manufacturer datasheet typical-characteristic curves to verify settling, output swing, and stability for the intended gain and signal amplitude.
Do not assume that the full 2.7 V to 36 V supply span is simultaneously available at the input and output. Check common-mode range, output swing, and input-offset requirements at the lowest operating voltage. Single-supply designs also require careful biasing of the signal source so the amplifier does not saturate near ground during startup or sensor excursions.
Route high-impedance input and feedback nodes away from switching nodes, inductors, relay contacts, and fast digital clocks. Use a continuous ground reference beneath the SOIC where practical, and avoid splitting the ground plane beneath the amplifier. If the circuit includes an ADC or sensor with long leads, terminate the cable at the connector and provide local filtering rather than relying on distant filtering.
Impormasyon ng Pagsunod sa Kautusan
The general-purpose OPA237UA is not presented as an AEC-Q100-qualified automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.