Texas Instruments

OPA237UA - 1.5MHz Single-Supply Op Amp | Texas Instruments

MPN: OPA237UA ✓ فعال
2.7 V to 36 V Vdss 8 mA Id 8-pin SOIC Package
حداقل سفارش: 1 |

OPA237UA نمای کلی

Texas Instruments OPA237UA is a single-amplifier, single-supply operational amplifier designed for low-power signal-conditioning and precision analog applications. Its headline specifications include a 1.5 MHz gain-bandwidth product, 0.5 V/µs slew rate, and a 2.7 V to 36 V supply range, all housed in an 8-pin SOIC package. The device belongs to Texas Instruments’ MicroAmplifier product family, combining compact packaging with low offset voltage, low quiescent current, and low bias current.

An operational amplifier is a voltage-gain element that uses feedback to amplify the difference between its non-inverting and inverting inputs. The OPA237 family is optimized for operation from a single positive supply, including systems powered by batteries or low-voltage industrial rails. Its topology and electrical characteristics make it suitable for buffering, current sensing, analog measurement, filtering, and precision control. A single-amplifier package also allows designers to conserve board area when only one amplifier channel is required.

Key performance characteristics include a 1.5 MHz gain-bandwidth product for moderate-frequency analog signals and a 0.5 V/µs slew rate for large-signal response. The stated 78 dB common-mode rejection ratio helps reject common-mode interference, while the stated 100 dB power-supply rejection ratio indicates strong isolation from supply ripple. An 8 mA output-current capability supports the input and output stages required by typical low-power analog circuits.

OPA237UA operates from a 2.7 V to 36 V supply, enabling use across low-voltage battery systems and higher-voltage industrial equipment. Its single-supply architecture supports input and output signals referenced near ground when appropriate for the selected feedback network. The 8-pin SOIC footprint is suitable for conventional surface-mount assembly and board-level replacement planning, although input bias, offset, noise, stability, and output-swing constraints must be checked against the actual application.

Typical uses include low-side current measurement, sensor amplification, active filtering, transducer interfaces, buffered analog inputs, and precision control loops. The 1.5 MHz bandwidth is particularly appropriate for slow sensor signals, instrumentation, and general-purpose signal conditioning rather than high-frequency video or RF amplification. The 36 V maximum supply also makes the device useful in industrial systems where signal amplitudes and supply transients exceed typical consumer levels.

Designers should place input, feedback, and bypass components close to the amplifier pins to minimize parasitic feedback and maintain signal integrity. The SOIC package offers a practical thermal path on a conventional PCB, but sustained output current still requires careful assessment of power dissipation, copper area, and adjacent heat sources. Stable operation also depends on selecting feedback values compatible with the device’s gain-bandwidth and output-drive characteristics.

This page combines manufacturer specifications, package and pin information, drop-in replacement guidance, application-focused design notes, and parameter comparisons. It provides practical context for evaluating the OPA237UA alongside other single-amplifier choices while keeping circuit compatibility, supply range, bandwidth, and package constraints visible.

جایگزین‌های drop-in برای OPA237UA — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

OPA237UA/2K5G4

✅ جایگزین مستقیم
📦 8-pin SOIC
Same 1.5 MHz bandwidth, 0.5 V/µs slew rate, 36 V maximum supply, and 8-pin SOIC configuration; ordering suffix specifies 2,500-unit reel packaging

📋 جایگزین مرجع (خارج از کاتالوگ)

OPA237UA حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type Single operational amplifier
Gain-Bandwidth Product 1.5 MHz
Slew Rate 0.5 V/µs
Supply Voltage Range 2.7 V to 36 V
Common-Mode Rejection Ratio 78 dB
Power-Supply Rejection Ratio 100 dB
Output Current 8 mA
Number of Channels 1 channel
بسته‌بندی 8-pin SOIC
نوع نصب Surface mount
Supply Type Single supply
محدوده دمای کاری -40 °C to +85 °C

پیکربندی پین OPA237UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 NC — Not connected (per datasheet)
پین 2 IN- — Inverting input
پین 3 IN+ — Non-inverting input
پین 4 V- — Negative supply connection
پین 5 NC — Not connected (per datasheet)
پین 6 OUT — Amplifier output
پین 7 V+ — Positive supply connection
پین 8 NC — Not connected (per datasheet)

کاربردهای معمول

OPA237UA مناسب است برای 6 کاربردs: Low-Side Current Sensing, Sensor Signal Conditioning, Active Analog Filtering, Industrial Analog Measurement, Battery-Powered Instrumentation, Precision Control Loops.

⚡

Low-Side Current Sensing

OPA237UA fits low-side current measurements because its 1.5 MHz gain-bandwidth product can amplify the small voltage generated by a shunt without adding substantial bandwidth limitations. The stated 78 dB common-mode rejection ratio helps reject voltage shared by the shunt, supply, and measurement ground, while the 2.7 V to 36 V supply range supports both compact battery-powered monitors and industrial measurement circuits. Place the amplifier close to the shunt and ADC input to minimize copper resistance and parasitic pickup. Check the common-mode input range at the selected supply voltage before finalizing the gain and shunt resistance.

🧩

Sensor Signal Conditioning

OPA237UA can amplify and buffer resistive sensor outputs such as thermistors, potentiometers, and resistive bridges when the signal bandwidth remains below its 1.5 MHz gain-bandwidth product. Its low-power single-supply operation is useful for portable instrumentation, and the 36 V maximum supply provides additional range for industrial sensor interfaces. The 100 dB power-supply rejection ratio helps prevent supply ripple from appearing at the conditioned output. Use resistor values that preserve the required closed-loop gain and verify sensor excitation current, input bias error, and output headroom.

🔧

Active Analog Filtering

OPA237UA is appropriate for first-order or modest higher-order active filters operating at low-to-moderate frequencies. Its 1.5 MHz gain-bandwidth product provides bandwidth beyond many sensor-band applications, while the 0.5 V/µs slew rate must be checked against the filter’s largest expected output transitions. The single 8-pin SOIC package simplifies designs that require one noninverting or inverting active-filter stage. Component tolerances and amplifier noise should be included when determining filter cutoff accuracy, and the completed circuit should be stability-checked across its full input and output signal range.

🏭

Industrial Analog Measurement

OPA237UA supports industrial analog measurement front ends where signals must be conditioned before conversion or control. Its supply range extends to 36 V, permitting use in systems with a higher nominal rail than ordinary low-voltage consumer circuits. The 78 dB common-mode rejection ratio is valuable when the measurement input includes substantial common-mode voltage, and the 100 dB power-supply rejection ratio helps isolate the signal path from supply variation. The amplifier still requires adequate transient protection, grounding, and input-range analysis for industrial surge and ground-offset conditions.

📱

Battery-Powered Instrumentation

OPA237UA is suitable for portable, battery-powered instruments because it is designed as a single-supply amplifier and can operate from rails as low as 2.7 V. A 1.5 MHz bandwidth is suitable for many physiological, environmental, and general-purpose sensor signals without requiring a high-speed amplifier. Low-voltage operation requires careful attention to output swing and common-mode headroom, particularly near the lower supply limit. Select resistor and reference networks that keep the signal inside those limits, and use local supply bypassing to reduce supply ripple coupled into the measurement chain.

⚡

Precision Control Loops

OPA237UA can serve as the error amplifier in low-frequency control and feedback systems where loop bandwidth remains well below its 1.5 MHz gain-bandwidth product. The 0.5 V/µs slew rate provides finite large-signal response, so loop compensation must account for the rate at which the control output can move. Single-supply operation simplifies systems whose actuator and sensor share a positive rail, while the 36 V upper limit permits use in higher-voltage control platforms. Verify startup behavior, output saturation limits, and noise before closing the loop around the selected actuator.

What are the key specifications of OPA237UA that engineers should know?
OPA237UA is a single-supply operational amplifier with a 1.5 MHz gain-bandwidth product, 0.5 V/µs slew rate, and a 2.7 V to 36 V operating supply range in an 8-pin SOIC package. According to the Texas Instruments OPA237 manufacturer datasheet, it also provides 78 dB common-mode rejection, 100 dB power-supply rejection, and an 8 mA output-current rating. These characteristics position it as a general-purpose amplifier for signal conditioning, buffering, filtering, current sensing, analog measurement, and precision control.
What is the operating voltage range of OPA237UA?
OPA237UA operates from 2.7 V to 36 V as a single-supply amplifier. The Texas Instruments OPA237 manufacturer datasheet identifies this range as the supported supply span for the family, allowing operation from low-voltage battery-powered systems through higher-voltage industrial rails. Verify the input common-mode and output-swing limits for the selected 2.7 V operating point because the usable signal range can be narrower than the supply voltage.
What is the gain-bandwidth product of OPA237UA?
OPA237UA has a gain-bandwidth product of 1.5 MHz. According to the Texas Instruments OPA237 manufacturer datasheet, this nominal value describes the relationship between closed-loop gain and usable bandwidth for the amplifier. It makes the device appropriate for low- and moderate-frequency analog signals, including sensor conditioning, active filters, and instrumentation. It is not intended to provide the bandwidth normally associated with high-speed video or RF amplifiers.
What is the slew rate of OPA237UA and why does it matter?
OPA237UA has a slew rate of 0.5 V/µs, as stated in the Texas Instruments OPA237 manufacturer datasheet. Slew rate limits how quickly the output can change in response to a large voltage step. The 0.5 V/µs rating is suitable for many sensor, control, and general signal-conditioning applications, but waveforms requiring faster edge rates may need an amplifier with a higher slew-rate specification.
Where can I download the OPA237UA datasheet PDF?
The official OPA237UA datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/opa237.pdf. The document contains the authoritative electrical characteristics, ordering information, pin descriptions, typical performance curves, and application guidance. Use the manufacturer datasheet when assigning PCB pins, checking input and output limits, or confirming values that are not shown in a distributor catalog.
Where can I find the OPA237UA pinout?
The OPA237UA pinout is shown in the Texas Instruments OPA237 manufacturer datasheet under the pin-configuration and pin-description sections. OPA237UA uses an 8-pin SOIC package. For a standard single-amplifier implementation, use the datasheet pin-description table when routing the inverting input, non-inverting input, supply rails, output, and no-connect positions rather than relying only on a generic package drawing.
Is OPA237UA suitable for single 5 V supply designs?
Yes, OPA237UA is designed for single-supply operation and its 2.7 V to 36 V supply range includes a 5 V rail. The Texas Instruments OPA237 manufacturer datasheet specifically describes the family for single-supply, battery-powered, and portable applications. The circuit must still keep the input voltage and output swing inside the limits for the chosen supply voltage, and input/output references should be selected to avoid saturation.
What is the best drop-in replacement for OPA237UA?
OPA237UA/2K5G4 is the closest same-footprint TI alternative because it is the same OPA237UA device configured for 2,500-unit reel packaging. It provides the same 1.5 MHz bandwidth, 0.5 V/µs slew rate, and 8-pin SOIC electrical configuration, but its ordering code and shipment format differ. Confirm package markings, sourcing requirements, and production availability before changing an approved BOM.
Can OPA237UA replace OPA237UA/2K5G4?
OPA237UA and OPA237UA/2K5G4 use the same 8-pin SOIC footprint and correspond to the same OPA237UA amplifier configuration, so the former can serve as a pin-compatible substitution when the required shipping format and quality-control conditions are satisfied. The principal practical distinction is the ordering and packaging suffix. Confirm the manufacturer ordering information and approved-source documentation before treating the parts as interchangeable in production.
OPA237UA vs OPA237UA/2K5G4 — which is better for a production BOM?
OPA237UA/2K5G4 is generally the better production choice when the production quantity is 2,500 units and reel packaging is required, while OPA237UA is the standard ordering option. Both correspond to the same 1.5 MHz, single-supply amplifier in an 8-pin SOIC and have the same stated core specifications. Selection should follow the approved BOM, incoming-inspection requirements, and manufacturing plan rather than electrical differences alone.
When should I choose OPA237UA over a dual operational amplifier?
Choose OPA237UA when the design needs only one amplifier channel and reducing board area is important. It provides one amplifier in an 8-pin SOIC, so an unused second channel does not occupy additional pins. A dual device can be preferable when two closely related channels are required, when a second amplifier is needed for signal generation or feedback, or when reducing the total component count is more important than using every package pin.
Is OPA237UA suitable for current sensing and sensor conditioning?
Yes, OPA237UA is suitable for current sensing, sensor conditioning, buffering, and filtering. Its 78 dB common-mode rejection ratio helps suppress common-mode voltage, while the 100 dB power-supply rejection ratio reduces supply-ripple coupling according to the Texas Instruments OPA237 manufacturer datasheet. The 1.5 MHz bandwidth is adequate for many slow sensor and measurement paths, subject to checking input offset, bias current, and output-swing requirements.
Where can I buy OPA237UA online?
Use the Request a Quote form on this page to request OPA237UA pricing, stock confirmation, and lead time. The form allows the exact 8-pin SOIC ordering configuration to be quoted without relying on a generic product listing. Include the required quantity, delivery location, acceptable date code, and reel or other shipping requirements so the quotation reflects the part and packaging needed for production.
What is the lead time for OPA237UA?
Current OPA237UA lead time depends on order quantity, factory loading, date-code requirements, and packaging configuration. Request a Quote on this page for a date-specific manufacturing and delivery schedule, and state the required reel quantity and acceptable date-code policy. Do not rely on an unverified inventory count when planning a production build, because availability can change independently of the device’s active lifecycle status.
Is OPA237UA in stock?
OPA237UA can be requested through the Request a Quote form on this page, where the exact ordering code and current supply status should be confirmed for the requested quantity. Because stock levels vary by package, shipment format, date code, and region, inventory should not be inferred from the presence of an active Texas Instruments product page. Include the required quantity and production window in the request.

داده‌های مرجع مهندسی برای OPA237UA — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose OPA237UA when the circuit needs one low-to-moderate-bandwidth amplifier on a single supply between 2.7 V and 36 V. It is a practical fit for sensor conditioning, current sensing, buffering, filtering, and low-frequency control where the 1.5 MHz gain-bandwidth product and 0.5 V/µs slew rate are sufficient. Choose OPA237UA/2K5G4 when the approved production plan specifically calls for 2,500-unit reel packaging; its electrical configuration and 8-pin SOIC footprint remain the same. A dual amplifier is preferable when two related signal paths are required and eliminating a separate package is more important than minimizing pins per channel. Before finalizing any choice, verify the input common-mode range, output swing, offset, bias current, noise, stability, and operating temperature requirements in the Texas Instruments OPA237 manufacturer datasheet.

مقایسه با جایگزین‌ها

پارامتر این محصول OPA237UA/2K5G4
Brand Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC - same footprint
Amplifier Channels 1 channel 1 channel
Supply Range 2.7 V to 36 V 2.7 V to 36 V
Gain-Bandwidth Product 1.5 MHz 1.5 MHz
Slew Rate 0.5 V/µs 0.5 V/µs
Common-Mode Rejection Ratio 78 dB 78 dB
Power-Supply Rejection Ratio 100 dB 100 dB
Output Current 8 mA 8 mA
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C
Ordering Configuration OPA237UA OPA237UA/2K5G4 with 2,500-unit reel packaging
Price Tier Request a Quote Request a Quote

تفاوت‌های کلیدی

  • Direct single-amplifier ordering option in an 8-pin SOIC (در مقابلOPA237UA/2K5G4)
  • Wide supply-range capability in a compact single channel (در مقابلOPA237UA/2K5G4)
  • Same electrical configuration for manufacturing substitution (در مقابلOPA237UA/2K5G4)

یادداشت‌های طراحی

Place the amplifier, input components, feedback resistors, and supply-bypass capacitor close together to minimize parasitic feedback and high-frequency coupling. Keep the inverting-input trace short because it is especially sensitive to capacitance from adjacent signals. For a noninverting configuration, connect the feedback network directly to pins 2 and 6 and place the bypass capacitor between pins 7 and 4 near the package.

The OPA237UA supply range extends to 36 V, but the actual power dissipation depends on supply voltage, output voltage, quiescent current, and load current. Estimated maximum package dissipation can be calculated as PD ≈ (V+ − |VOUT|) × IOUT plus internal losses; verify the result against the manufacturer’s maximum power and temperature-rise limits before operating near the upper supply limit.

Account for the 1.5 MHz gain-bandwidth product when selecting closed-loop gain. A higher gain reduces usable signal bandwidth, while a 0.5 V/µs slew rate can limit large-signal output response even when small-signal bandwidth appears adequate. Use the Texas Instruments OPA237 manufacturer datasheet typical-characteristic curves to verify settling, output swing, and stability for the intended gain and signal amplitude.

Do not assume that the full 2.7 V to 36 V supply span is simultaneously available at the input and output. Check common-mode range, output swing, and input-offset requirements at the lowest operating voltage. Single-supply designs also require careful biasing of the signal source so the amplifier does not saturate near ground during startup or sensor excursions.

Route high-impedance input and feedback nodes away from switching nodes, inductors, relay contacts, and fast digital clocks. Use a continuous ground reference beneath the SOIC where practical, and avoid splitting the ground plane beneath the amplifier. If the circuit includes an ADC or sensor with long leads, terminate the cable at the connector and provide local filtering rather than relying on distant filtering.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The general-purpose OPA237UA is not presented as an AEC-Q100-qualified automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

OPA237UA datasheet OPA237UA pinout OPA237UA datasheet pdf OPA237UA SOIC-8 OPA237UA specifications OPA237UA 1.5MHz OPA237UA 36V OPA237UA replacement OPA237UA equivalent OPA237UA vs OPA237UA/2K5G4 Texas Instruments OPA237UA OPA237UA application circuit OPA237UA price OPA237UA stock

قطعات و اصطلاحات مرتبط

Texas Instruments OPA237UA OPA237UA/2K5G4 OPA237 MicroAmplifier operational amplifier single-supply operational amplifier signal conditioning current sensing active filtering precision control gain-bandwidth product slew rate common-mode rejection ratio power-supply rejection ratio 8-pin SOIC SOIC package family surface-mount single-supply operation battery-powered instrumentation industrial analog measurement input common-mode range output swing quiescent current
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ