Texas Instruments

PCA9534ADWR - 8-Bit I/O Expander | Texas Instruments

MPN: PCA9534ADWR ✓ Nakahanda
2.3 V to 5.5 V Vdss 1 uA Id 16-pin SOIC (DW) Package 400 kHz Speed
MOQ: 1 |

PCA9534ADWR Ulas

The Texas Instruments PCA9534ADWR is an 8-bit I2C and SMBus low-power I/O expander with an interrupt output and configuration registers. It operates from 2.3 V to 5.5 V, supports bus speeds up to 400 kHz, and is packaged in a 16-pin SOIC (DW) package. The device provides eight remotely controlled general-purpose digital I/O ports through a serial bus, reducing the number of host-controller pins required for sensors, switches, indicators, and other discrete interfaces.

An I/O expander is an interface IC that converts serial commands into parallel digital control lines. The PCA9534ADWR belongs to the I/O expander class, where the broader hierarchy is interface IC, bus-controlled peripheral, and low-power semiconductor. It connects to a host through the two-wire I2C bus or compatible SMBus interface, allowing the host to read input states and configure output states through registers rather than dedicating eight GPIO pins on the host.

The principal features include eight configurable I/O lines, interrupt and configuration registers, operation across a 2.3 V to 5.5 V supply range, and 400 kHz I2C operation. Maximum standby current is listed as 1 uA, making the expander suitable for power-conscious embedded systems. The interrupt output is open-drain and active low, allowing multiple expansion devices to share an interrupt line when they are configured for the same bus address.

Each port pin can operate as an input or output, and the configuration registers determine the direction and electrical behavior of those pins. Register-based control permits software-defined mapping between bus commands and external circuitry. The serial interface also provides a practical way to add control lines without increasing the pin count of a microcontroller, processor, or programmable logic device. The PCA9534A family is described by Texas Instruments as pin-to-pin and I2C-address compatible with the PCF8574A, although software changes are required to use its enhanced register functions.

Typical applications include portable instrumentation, industrial control modules, sensor and switch interfaces, LED or relay control, programmable logic expansion, and compact embedded products. In a sensor interface, one device can gather several digital status inputs and drive multiple enables. In a control module, the same expander can operate an alarm line, mode selector, or status indicator while an interrupt tells the host that an input state has changed.

Designers should verify pin multiplexing, address selection, pull-up requirements, and open-drain interrupt wiring against the manufacturer datasheet before layout is released. Bus pull-up resistors depend on the operating voltage, bus capacitance, and selected clock rate. A common interface error is treating configuration-register bits as if they were direct port states, so firmware should initialize the device explicitly and test both input and output modes during bring-up.

This page combines device specifications, package and interface details, practical replacement guidance, and application-specific design guidance. It also distinguishes electrically similar devices from true pin-compatible choices, helping engineers assess replacement risk without treating a similar bus interface as proof of drop-in compatibility.

Mga alternatibo na pwedeng ilagay na PCA9534ADWR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

TCA9534ADWR

✅ Drop-In
📦 16-pin SOIC (DW)
Same 8-port count and 400 kHz I2C rating; interrupt and register details require firmware review

📋 Alternatibo na Reference (hindi sa katalogo)

PCA9534PWRG4

✅ Drop-In
📦 16-pin SOIC (DW)
Same PCA9534 family and 8-bit port architecture; exact ordering suffix and package dimensions require comparison

📋 Alternatibo na Reference (hindi sa katalogo)

PCA9534PW,118

✅ Drop-In
📦 16-pin SOIC (DW)
Same PCA9534 family and 8-bit I/O topology; manufacturer-specific register and lifecycle details require review

📋 Alternatibo na Reference (hindi sa katalogo)

PCA9534ADWR Mga Spesipikasyon

Device Type 8-bit I2C/SMBus I/O expander
Number of I/O Ports 8 ports
Number of I/O Lines 8 lines
Operating Supply Voltage Range 2.3 V to 5.5 V
I2C Bus Frequency 400 kHz
Uri ng Interface I2C and SMBus
Interrupt Output Open-drain, active-low
Configuration Registers Present
Maximum Standby Current 1 uA
Hanay ng Temperature na Operasyon -40 C to +85 C
Packhaging 16-pin SOIC (DW)
Uri ng Pagpapasok Surface mount
Bilang ng Pins 16 pins
Address Compatibility Compatible with PCF8574A, with software changes required

Gabay sa Pin Configuration ng PCA9534ADWR 16-pin soic (dw)

Pin configuration para sa PCA9534ADWR (16-pin soic (dw) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 16-pin soic (dw) package para sa PCA9534ADWR

Wala ng detalyadong pinout data na magagamit para sa PCA9534ADWR.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

PCA9534ADWR ay nararapat para sa 6 aplikasyons: Portable Sensor and Switch Interface, Industrial Control Module, LED and Indicator Control, Programmable Logic Interface Expansion, Alarm and Security Peripheral, Automotive or Battery-Powered Equipment.

📱

Portable Sensor and Switch Interface

The PCA9534ADWR is well suited to portable systems that must monitor several digital sensors and control selectors without assigning a dedicated GPIO to every signal. Its 8-bit port capacity provides eight configurable lines, while the 2.3 V to 5.5 V range supports low-voltage embedded systems. The 400 kHz I2C interface transfers port states efficiently, and the open-drain, active-low interrupt can notify the host when an input changes. Maximum standby current is 1 uA, helping preserve battery life during inactive periods. Place the device close to the external signal connector, keep the interrupt route away from high-current switching edges, and verify pull-up values against the intended bus voltage.

🏭

Industrial Control Module

In an industrial control module, PCA9534ADWR can consolidate digital mode inputs, fault flags, relay enables, and status LEDs behind an I2C bus. The device operates from 2.3 V to 5.5 V and supports 400 kHz communication, allowing it to coexist with common embedded control architectures. The interrupt output provides an efficient way for the controller to detect a changed input rather than continuously polling all eight lines. Configure input pins for the external voltage levels, define output polarities explicitly, and account for inrush current when switching inductive loads. Keep the expander’s supply and ground return close to the relevant circuitry so switching disturbances do not create false input transitions.

💡

LED and Indicator Control

PCA9534ADWR can drive grouped LED indicators, panel status lights, and selection markers without expanding the host controller’s pin count. Eight configurable outputs provide flexible control for a display or control panel, while the 400 kHz I2C bus supports fast register updates. Because the device is a low-voltage digital expander, LED current limiting and any required transistor driver must be implemented separately rather than assumed to be integrated. Check output drive capability and absolute output limits in the manufacturer datasheet, and use current-limiting resistors on direct LED connections. A common-p cathode or common-anode arrangement can reduce component count, but programming polarity must match the physical wiring.

🖥️

Programmable Logic Interface Expansion

The PCA9534ADWR is useful when a programmable-logic design needs additional discrete controls but its main I/O budget is constrained. A master controller can write configuration and port registers over I2C at up to 400 kHz, then read the eight input states when required. The 2.3 V to 5.5 V supply range allows integration with compatible logic levels, while the small 16-pin SOIC package supports compact layouts. Treat the interrupt line as a shared resource if several expanders are present, and ensure every attached device uses a unique address or is otherwise isolated. Timing closure must include bus capacitance, pull-up resistance, and the propagation delay of the external signals being monitored.

🛡️

Alarm and Security Peripheral

PCA9534ADWR can collect door, tamper, presence, or enclosure status signals and drive local alarm-enable outputs in a compact security peripheral. The active-low, open-drain interrupt output is useful for signaling an input-state change to the host, while the eight-port count can combine several monitored inputs with a small number of control outputs. Operating down to 2.3 V supports embedded security equipment, and the 1 uA maximum standby current is beneficial in duty-cycled installations. Confirm the behavior of unused pins and the default state of every output after reset. For reliable detection, debounce mechanical inputs in firmware and account for contact bounce rather than treating every interrupt transition as an immediate alarm event.

🚗

Automotive or Battery-Powered Equipment

PCA9534ADWR can add remote control and status lines in battery-powered equipment where host GPIO availability is limited. Its 2.3 V minimum operating voltage, 1 uA maximum standby current, and eight configurable I/O lines support compact, low-power designs. The device can supervise switches, monitor enable signals, and control low-current indicators through I2C rather than direct host wiring. In a vehicle or other electrically noisy environment, maintain short return paths, decouple the supply locally, and validate every external signal against the pin voltage limits. A qualified automotive variant should be selected when AEC-Q100 requirements apply; the qualification status of this exact orderable code must be confirmed before release.

Buod ng mga Inirekomendang Produkto

TCA9534ADWR Same-footprint 8-bit I2C expander candidate Ginagamit sa: Portable Sensor and Switch Interface, Industrial Control Module, LED and Indicator Control, Programmable Logic Interface Expansion, Alarm and Security Peripheral, Automotive or Battery-Powered Equipment PCA9534PW,118 Cross-manufacturer PCA9534-family interface candidate Ginagamit sa: Portable Sensor and Switch Interface, Programmable Logic Interface Expansion, Automotive or Battery-Powered Equipment PCA9534PWRG4 Same-family PCA9534 interface candidate Ginagamit sa: Industrial Control Module, LED and Indicator Control, Alarm and Security Peripheral
What is the PCA9534ADWR?
The PCA9534ADWR is an 8-bit I2C and SMBus low-power I/O expander with an interrupt output and configuration registers. According to the Texas Instruments product page, it operates from 2.3 V to 5.5 V, supports 400 kHz I2C communication, and uses a 16-pin SOIC (DW) package. Its eight general-purpose I/O lines connect external switches, sensors, indicators, and control signals to a host controller through a two-wire serial bus.
What are the key specifications of PCA9534ADWR that engineers should know?
The PCA9534ADWR provides eight configurable I/O lines, a 2.3 V to 5.5 V operating range, and I2C communication up to 400 kHz. Texas Instruments also identifies a maximum standby current of 1 uA and an open-drain, active-low interrupt output. The device is offered in a 16-pin SOIC (DW) package. These characteristics make it useful for expanding digital control and input capacity without assigning a separate host GPIO to every external signal.
Where can I download the PCA9534ADWR datasheet PDF?
The official PCA9534A part-details page provides access to the Texas Instruments PCA9534ADWR documentation and datasheet. The device is also indexed on datasheet aggregation services under the exact PCA9534ADWR orderable code. For design decisions, use the manufacturer document as the controlling reference for register definitions, pin multiplexing, electrical limits, and initialization requirements rather than relying on a secondary summary.
Where can I find the PCA9534ADWR pinout?
The PCA9534ADWR uses a 16-pin SOIC (DW) package, and its complete pin assignment is defined in the Texas Instruments datasheet pin-description table. Use that table when assigning address-select, clock, data, interrupt, ground, supply, and eight port functions to PCB nets. A complete numerical pin list cannot be safely reconstructed from the product-page summary alone, so consult the manufacturer pin-description table before routing or replacing the device.
Can TCA9534ADWR replace PCA9534ADWR as a drop-in part?
TCA9534ADWR is the closest same-manufacturer candidate identified for a footprint-compatible replacement, and it is also listed as an 8-bit, 400 kHz I2C expander in a 16-pin SOIC package. The key quantified match is the same eight-port count and 400 kHz bus capability. Firmware and register behavior must still be checked against both datasheets before production use, particularly for interrupt, polarity, and default-state requirements.
What is the best NXP equivalent for PCA9534ADWR?
PCA9534PW,118 is the cross-manufacturer candidate identified for evaluation against PCA9534ADWR. It carries the same PCA9534 family designation, while the comparison page for the exact NXP and Texas Instruments orderable codes provides a direct parameter comparison. Because an exact package drawing and pin-by-pin electrical comparison are needed before replacement, treat this as a candidate rather than an unconditional production substitution.
Is PCA9534ADWR compatible with PCF8574A?
The PCA9534A family is pin-to-pin and I2C-address compatible with the PCF8574A, according to Texas Instruments. The important qualification is software-related: firmware must be changed for the PCA9534A enhancements and its configuration-register architecture. Hardware compatibility therefore simplifies PCB substitution, but it does not permit existing PCF8574A software to be transferred without review and modification.
When should I choose PCA9534ADWR instead of PCF8574A?
Choose PCA9534ADWR when the design benefits from configuration registers, interrupt support, and the enhanced register behavior of the PCA9534A family. It retains pin-to-pin and I2C-address compatibility with PCF8574A, which can simplify a hardware migration, but the host firmware must be adapted. Existing PCF8574A software and boards may remain preferable when no new register features are required and software stability is the overriding concern.
What can replace PCA9534ADWR?
TCA9534ADWR, PCA9534PWRG4, and PCA9534PW,118 are the replacement candidates identified for the PCA9534ADWR. TCA9534ADWR matches the eight-port, 400 kHz, 16-pin SOIC description, while the two PCA9534-family candidates require package and ordering-code comparison before installation. No source confirms five distinct drop-in alternatives, so production substitution should be limited to candidates whose complete pin and register behavior has been verified.
Is PCA9534ADWR suitable for low-power embedded systems?
The PCA9534ADWR is suitable for low-power embedded systems because its listed maximum standby current is 1 uA and its operating supply range extends down to 2.3 V. It adds eight serial-controlled I/O lines without requiring eight dedicated host GPIO pins. Actual system consumption depends on supply voltage, bus activity, output loading, pull-up values, and the number of port pins left high, so measure the complete rail under the intended duty cycle.
How does PCA9534ADWR reduce GPIO usage?
PCA9534ADWR reduces GPIO usage by placing eight configurable digital I/O lines behind an I2C or SMBus interface. A host controller reads input states and writes output states through the expander registers, while the active-low open-drain interrupt output can signal a changed input condition. This is particularly useful when a design has consumed most available controller pins but still requires selectors, enables, status inputs, or indicator controls.
Where to buy PCA9534ADWR online?
Use the Request a Quote form on this page to request PCA9534ADWR pricing, stock, minimum order quantity, and lead time. The exact orderable code is PCA9534ADWR in a 16-pin SOIC (DW) package. Commercial availability can change by lot and date, so a current quotation should confirm the suffix, package, quantity, and delivery requirements rather than assuming that a family-level listing represents this exact part.
What is the price of PCA9534ADWR?
Use the Request a Quote form on this page for the current PCA9534ADWR unit price and quantity breaks. Pricing depends on order quantity, package suffix, inventory, and current market conditions. The commercial form also confirms whether the requested quantity can be supplied together and provides a dated quotation suitable for an engineering procurement plan.
What is the lead time for PCA9534ADWR?
Request the current PCA9534ADWR lead time through the Request a Quote form on this page. Lead time can vary with order quantity, production scheduling, and available inventory, so a confirmed quotation is preferable to a generic estimate. When requesting the quotation, specify the exact PCA9534ADWR orderable code, desired package form, annual demand, and target delivery date.
Is PCA9534ADWR in stock?
The current stock position for PCA9534ADWR should be confirmed through the Request a Quote form on this page. Availability is quantity-dependent and can change after each order, so a general product listing does not establish how many units can ship against a specific demand plan. Include required quantity, acceptable delivery date, and whether multiple delivery dates are acceptable in the quotation request.
What tools are needed to design with PCA9534ADWR?
The PCA9534ADWR can be evaluated with any host capable of driving an I2C bus at up to 400 kHz, plus logic-capture or oscilloscope equipment for troubleshooting. Firmware needs access to the device address, configuration registers, port registers, and interrupt input. The Texas Instruments datasheet is the controlling resource for register addresses, reset behavior, address selection, timing, and port-pin electrical behavior.
Does PCA9534ADWR comply with RoHS and REACH?
The RoHS and REACH status for PCA9534ADWR requires confirmation from the current manufacturer product documentation or declaration of conformity. The exact declarations should be checked for the orderable code rather than inferred from the product family name. For regulated production, request the applicable material-compliance declaration and retain it with the procurement and quality records for the shipped configuration.

Impormasyon ng Talumpati sa Engineering for PCA9534ADWR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose PCA9534ADWR when a compact design needs eight serial-controlled digital lines, operation from 2.3 V to 5.5 V, and an interrupt capable of reducing unnecessary polling. It is particularly attractive when the host has limited GPIO, the board must support both input sensing and output control, and the firmware team can implement the PCA9534A configuration registers. TCA9534ADWR is the closest same-manufacturer candidate when its register map, interrupt behavior, and lifecycle requirements match the design. PCA9534PWRG4 may suit an existing TI-family sourcing plan, but its exact suffix and package conditions should be checked. PCA9534PW,118 supports cross-manufacturer diversification, although device-specific behavior and qualification must be reviewed. For a PCF8574A migration, the PCA9534ADWR offers hardware compatibility with register-based enhancements, but existing firmware must be changed. Do not select a replacement solely from the eight-bit I/O description; verify package dimensions, pin multiplexing, electrical limits, address behavior, and supply range before release.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto TCA9534ADWR PCA9534PWRG4 PCA9534PW,118
Brand Texas Instruments Texas Instruments Texas Instruments NXP Semiconductors
Package 16-pin SOIC (DW) 16-pin SOIC (DW) 16-pin SOIC (DW) 16-pin SOIC (DW)
Device Type I/O Expander I/O Expander I/O Expander I/O Expander
Number of I/O Lines 8 lines 8 lines 8 lines 8 lines
Bus Interface I2C and SMBus I2C I2C and SMBus I2C and SMBus
Price Request a Quote Request a Quote Request a Quote Request a Quote

Pangunahing mga Pagkakaiba

  • Directly identified PCA9534A-family orderable device (kumpara saPCA9534PW,118)
  • Same-manufacturer TCA9534 option (kumpara saTCA9534ADWR)
  • Eight configurable lines at a 400 kHz bus rate (kumpara saPCA9534PWRG4)
  • PCA9534A configuration and interrupt architecture (kumpara saPCA9534PW,118)

Talaan ng Disenyo

Route SDA and SCL as a compact, continuous bus and place the required pull-up resistors near the master or the appropriate point defined by the system’s bus topology. The target supports 400 kHz, but usable speed also depends on total bus capacitance, pull-up resistance, clock stretching, and peripheral timing. Keep the I2C traces away from switching-power nodes and high-current relay or motor traces to reduce false edges and communication retries.

Do not assume that PCF8574A firmware can operate the PCA9534A without modification. Texas Instruments states that the devices are pin-to-pin and I2C-address compatible, while software changes are required for the PCA9534A enhancements. Review the configuration-register map, reset state, input polarity, output latch behavior, and interrupt semantics. Firmware should also initialize the direction register before driving outputs and account for mechanical input debounce where applicable.

Decouple the PCA9534ADWR supply with the capacitance recommended by the manufacturer datasheet and place it close to the device’s supply and ground pins. Although the listed maximum standby current is 1 uA, operating current and total system demand depend on clock activity and the states of the eight port lines. Use pull-up values appropriate for the operating voltage and bus capacitance, and calculate the worst-case logic-high current for any port that remains continuously active.

Treat the open-drain, active-low interrupt as a wired-AND resource when several expanders share it. Each device should be configured so its interrupt remains deasserted until the relevant input changes, and the shared line requires an appropriate pull-up. Keep the interrupt trace short and isolated from noisy coupling paths. Before production, compare every package drawing, including lead width, pitch, pin numbering, and exposed-pad requirements where applicable.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The manufacturer product page and indexed technical descriptions do not state the complete compliance declarations for this orderable code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer declarations before production release.

Kaugnay na Hanapin

PCA9534ADWR PCA9534ADWR datasheet PCA9534ADWR datasheet pdf PCA9534ADWR pinout PCA9534ADWR schematic PCA9534ADWR equivalent PCA9534ADWR replacement PCA9534ADWR cross reference PCA9534ADWR vs TCA9534ADWR PCA9534ADWR footprint PCA9534ADWR price PCA9534ADWR stock Texas Instruments PCA9534ADWR PCA9534ADWR application circuit

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments PCA9534ADWR PCA9534A TCA9534ADWR PCA9534PWRG4 PCA9534PW,118 NXP Semiconductors I/O expander interface IC parallel I/O I2C SMBus open-drain interrupt active-low interrupt configuration register 16-pin SOIC DW package surface-mount package digital sensor interface industrial control module programmable logic expansion low-power embedded system 2.3 V to 5.5 V operation 400 kHz I2C 1 uA standby current
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ